|
October 1, 2013 SIGN COMPONENTS MANUAL (SAM) 94
<br />Ribbon Strip Series, Super Tiny Series.1. These products are only suitable for connection to a UL Listed or Recognized
<br />maximum Class 2, 12 V DC power source.
<br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 circuit
<br />limits.
<br />3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
<br />of the Class 2 supply. Each module is rated 60W, 5A, and Max. 120 of LED modules per string.
<br />4. These products are suitable for use in dry. damp or wet locations.
<br />5. These products are not required to be enclosed or protected from the weather.
<br />Sign accessories, Class 2 LED power supplies, Model MB-12760-12V Multi Drive Series Maxbrite LED power supply.
<br />1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 12 Volt
<br />DC or less.
<br />2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
<br />of the Class 2 supply.
<br />3. These products are not required to be enclosed or protected from the weather in the end product.
<br />4. These products may be secured in place in the end product by any means available.
<br />Toggle Switch Boot, Model MB-TS20B.
<br />1. This switch boot was evaluated for use on a MaxBrite toggle switch(WOYR2)/E355116 part number MB-TS20, with 19 mm long
<br />actuator mounted on a 12mm tall threaded stem, with a 12 x 1.Omm thread. Suitability of any other switch size shall be
<br />determined in the end product.
<br />2. The suitability of the switch ratings shall be determined in the end product.
<br />3. This product is acceptable for use in dry, damp and wet locations.
<br />4. The water exclusion must be determined in the end product.
<br />Class 2 LED Drivers, Models MDS27760-12, DS12745-12, MDS12760-12, SLS27720-12, SLS27730-12, MDS12060-12,
<br />TPS 12060-12, TPS27760-12.
<br />1. The output of this component complies with Class 2 requirements in the Standard for Class 2 Power Units, UL 1310.
<br />2. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
<br />min. 2 inches spacing to top of enclosure.
<br />3. These products shall be enclosed in the end product.
<br />4. These power supplies are suitable for use in dry and damp locations.
<br />5. These devices are intended for factory installation only.
<br />6. This Class 2 power supply is not provided with any grounding. The enclosure must be grounded in the end product.
<br />Sign accessories, Class 2 LED power supplies, Models SLS27730-12V, SLS27730-24V, SLS27760-12V and SLS27760-24V.
<br />1. The units have been evaluated using a resistive load resulting in an output rated current of (1) 2.5 A for SLS27730-12V, (2) 1.25
<br />A for SLS27730-24V, (3) 5 A for SLS27760-12V, (4) 2.5 A for SLS27760-24V respectively. The need for repeating tests related
<br />to heating and the isolated output shall be considered in the end product.
<br />2. The units have been tested at 40°C ambient. The measured maximum surface temperatures are as follows. Acceptable
<br />operation at a higher temperature should be determined in end products.
<br />Model Surface temperature (degree C) / Location
<br />SLS27730-12V 50.9 / enclosure outside top of Tl
<br />SLS27730-24V 50.0 / enclosure outside top of Tl
<br />SLS27760-12V 59.9 / enclosure outside top of Tl
<br />SLS27760-24V 51.9 / enclosure outside top of Tl
<br />3. The units are intended for operated in a maximum 20 A branch circuit.
<br />4. The LED driver bodies have been evaluated for certain wet location requirments. The thermoplastic UV rating determination and
<br />precondition before impact not completed since it is anticipated the thermoplastic parts of this unit will be protected in the end
<br />use. To be considered in end use.
<br />5. Only the U-Shaped inside metal enclosure was considered as protective bonded for SLS27730-12V and SLS27730-24V, the
<br />metal chassis of these models need to be reliably bonded to the earthed chassis in the end product. The outside metal
<br />enclosure was considered as protective bonded for SLS27760-12V and SLS27760-24V.
<br />6. The LED drivers are for built-in installation, the suitability of enclosure, mounting and inpuVoutput connections shall be
<br />determined in end-use product.
<br />7. The LED drivers are for factory-wiring only.
<br />8. Certain UL 8750 wet location requirements have been completed on this component, acceptance is to be determined in the end
<br />product on the need to account for any items not covered and to address any of the CSA requirements (CSA C22.2 No.250
<br />etc).
<br />9. The RTN output was connected to ground for all SELV Reliability and working voltage measurements as noted on the test data
<br />page.
<br />MEAN WELL ENTERPRISES CO LTD
<br />28 WUQUAN 3RD RD WUGU DIST
<br />E320521
<br />NEW TAIPEI, 248 TAIWAN
<br />LED array drivers, Model CLY-100-Z, Y can be G (for with Glue) or N (for without Glue), Z can be 12,15,20,24,27, 36 for output
<br />voltage; Model PLN-100-Zi Z can be 12,15, 20, 24, 27, 36 for output voltage; Models CLY-100-48, PLN-100-48, Y can be G (for
<br />with Glue) or N (for without Glue).
<br />1. These power supplies have a maximum of one Class 2 outputs. The output of these power supplies have been evaluated to
<br />Class 2 output requirements for dc circuits.
<br />2. These products have been evaluated for dry and damp locations use only..
<br />3. These devices shall be mounted in the intended manner within a suitable electrical enclosure.
<br />4. For Models CLN-100-Z only (Z=12,15, 20, 24, 27, 36, or 48), the temperature measured on top enclosure surface of was 63°C
<br />during the Temperature Test. For Models PLN-100-Z only (Z=12, 15, 20, 24, 27, 36, or 48), the temperature measured on top
<br />enclosure surface of was 72°C during the Temperature Test, For Models CLG-100-Z only (Z=12,15, 20, 24,27, 36 or 48), the
|