|
WI RI NG DIAGRAM
<br />Recommended Layout
<br />Density per Channel Width
<br />CAUTIONS
<br />AC POWER 12V DC USE 12V DC CONSTANT VOLT/GE INPUT ONLY
<br />DO NOT USE AC INPUT !
<br />9/16
<br />PIt
<br />MA•Incindr.,i.q.or.,ihr..1.:,IM",119.%,1.16:ed.g'.4,1™•Cion,;170,™1*,1:UN,1.•,1,241, F
<br />po-"hillph-,19'0Jn•:E-Ai.1-t·M/,41:.Ihni•ill,a.iw nut.1,•:,1,%* d.inmed'ht·r.0., 011 + Do not cut or rejoin wires while producti i is connected with live power source.
<br />. i
<br />-1 *1. -1-
<br />132·'
<br />1-2-1/2-4 4- 3" to 4" -4
<br />01'low Iwolows/hnodult·5
<br />of module'3"104"apart
<br />0,•,eliter pla,e modules at abotit
<br />lin" from edge of le:ter
<br /> DO NOT PERFORM ACTION LISTED BELOW• Alter or modify Strips
<br />• Touch LED lamps with sharp objects
<br />• Put glue or silicone over the LED lamps
<br />© Avoid performing installation under rainor high humidity and only install in
<br />temperatures above 50'F (10') to allow
<br />for better mounting tape adhesion
<br />i -1- 4== ==b . · 0 7.:r-Ja - 02.*,_----0 Z.*. --2 --0.-.84-- - 0 J.::,2.2.- 02.1:.- e.- 0 3·:, 0
<br />2" min.Min. Depmr Maximum driver quantity per serial1 Depth5 ' ma, ' connection is limited to available power supplyi
<br />wattage, failure causes overload of current and
<br />i damages to the product
<br />M STRIP MAX. WATTAGE •TO DRIVER ·
<br />.- -1 -
<br />.
<br />...., 5
<br />,
<br />Use recommended length for pitch between each module to achieve opti,num
<br />1 lighting output while maintaining lowest unit cost. Failure or misplacing will cause
<br />dimmed spols or uneven appearance of light on the surface. 2" minimum depth.
<br />PREPARATION
<br />POWERSUPPLYLOADING
<br />Tools Required Supplies Required
<br />Output(W)20W 30W 40W 45W 60W
<br />Max. Quantity \, 46
<br />U10 15 20 23 30
<br />W.retripe,.r,1,.ir.Di./i ..V:el. Itie Wilef:·in,Cal:,cnri 1[,CLoilneclon.w;feStrip Footage*
<br />Max. Length
<br />Recommended 15 ft 30 ft 50 ft 75 ft 100 ft
<br />Pr·epare Channel Letters
<br />Extension Wire
<br />f-··1.4
<br />18AWG 18AWG 16AWG 14AWG 12AWG
<br />efli
<br />oli 6 1
<br />* Maximum quantity for MAXBRITE Strip is based on approximately 85%t. (.1.ai, n,u%·,ri. ij.,11 ./ I f: uni tl/ ,0111... 111 ./.,el ,Ir ,....1,8...1
<br />...1, ...1·i·.i,/Ill......1,r·,IM,pedgeal
<br />of specified capacity of power supplies for extended lifespan. Equip with I,• K...0:•,JI•'!f,•Illwl·
<br />protective box for outdoor use and the box should have ventilating holes.
<br />Use only white paint Aide channels for better reflection
<br />© 2011 Ma:<Brite LED Lighting Technology - 1740-B Junction Ave. - San Jose, CA 95112
<br />Toll Free: 1-800-297-2210 - Fax: 1-408-437- 1602 1 www.maxbriteled.corn
<br />MA]{Brite
<br />L..................
|