Laserfiche WebLink
October 1, 2013 SIGN COMPONENTS MANUAL (SAM) 14 <br />1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC. <br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 <br />requirements. <br />3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited to <br />draw a total wattage of no greater than the secondary current rating of each Class 2 power supply. <br />Part No.Operating Current per Watts per module <br />voltage module <br />LS0723x 12Vdc 40mA 0.48W <br />LS0766x 12Vdc 30mA 0.36W <br />LS1769x 12Vdc 75mA 0.9ow <br />LS0776x 12Vdc 60mA 0.72W <br />4. These products are suitable for use in dry, damp and wet locations without additional enclosures. <br />Class 2 LED Modules, Model AA-0766EC-XX, where XX can be any alpha characters or blank to represent different light color <br />1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. <br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage <br />and energy limited circuit and which is rated greater than 12 V DC. <br />3. These Class 2 LED modules are each rated as noted in the electrical ratings tables. When units are connected to a Class 2 <br />circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. <br />4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less. <br />5. These products are not required to be enclosed or protected from the weather in the end product. <br />6. These products may be secured in place in the end product by any means available. <br />ABC SIGN PRODUCTS E80767 <br />2028 SE FRONTAGE RD <br />FT COLLINS, CO 80525 <br />Lampholder adapter, Type LH. <br />1. This device is suitable for use in indoor or outdoor extruded aluminum awning frames. <br />2. This adapter is intended for use only with Listed, single or double contact, recessed lampholders (Cat. No. 530, Kulka) which <br />snap-fit into, and are securely held by, the adapter. The lampholder shall be held securely with or without a lamp in place. <br />3. This adapter is intended to complete the enclosure housing of insulated live parts only. <br />4. This device shall be installed in an aluminum extrusion in accordance with the "Installation Instructions" supplied by the <br />manufacturer in the smallest shipping container. <br />Sign Face Tensioning System, Model ABC. <br />1. The suitability of these tensioning systems in combination with any R/C (UYMR2) Flexible Sign Face Material to prevent <br />entrance of water in outdoor sign applications shall be determined in the end product, <br />2. This product has not be evaluated for use as an electrical enclosure. <br />3. Tensioning clips shall be spaced as described in the Installation Instructions. <br />4. When employed in a sign with any frame dimension greater than 6 feet the sign shall be provided with a means to prevent <br />billowing. <br />5. The mounted assembly of sign face material in these tensioning systems shall comply with the electrical and thermal spacing <br />requirements of UL 48. <br />6. These clips have been determined to be suitable with any R/C Flexible Sign Face Material of min. 0.020 inches (0.51 mm) thick, <br />suitability for use with a material of lesser thickness shall be determined in the end product. <br />ABLE APPLIED TECHNOLOGIES LTD E329973 <br />BOUNDARY HOUSE BUSINESS CENTER <br />BOSTON MANOR RD <br />LONDON, W7 2QE UNITED KINGDOM <br />Class 2 LED Modules, Models MS-P40XXX-XX Series, where XXX-XX may be any alphanumeric characters. <br />1. These LED panel of these products are powered by Class 2 power source rated at max. 15 VDC, 5 amps. <br />2. These products are suitable for use in dry and damp locations. <br />3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, <br />and minimum 2 inches spacing to top of enclosure. <br />4. When provided with a power supply, in the end product the power supply spacing to other heat producing components shall be <br />minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. <br />5. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 limits. <br />ACROSENTEC CO LTD E363566 <br />253-9 GOCHUN-DONG <br />UIWANG-SHI, GYEONGGI-DO <br />437-801 REPUBLIC OF KOREA <br />Class 2 LED Modules, Models ASPCH-@4-24-$-%-&, ASFCH-@+24-$-%-&, and ASMX-@-'-24-*-!, where @ can be any 2 to <br />4 alphanumeric code, # can be any 3 to 5 alphanumeric code, $ can be any 2 or 3 alphanumeric code, % can be any 1 to 4 <br />alphanumeric code, & can be any 3 to 9 alphanumeric code, A can be any 3 to 5 alphanumeric code, * can be any 3 to 6 <br />alphanumeric code, ! can be any 2 to 9 alphanumeric code. <br />1. These products are only suitable for connection to a Class 2 power source rated 27 V DC or less.