Laserfiche WebLink
*,,,SANTA <br />ANA <br />lLl\\l\[ <br />& BIITDIIC <br />lct\fl <br />Plannlng & Bulldlng Agency <br />Bulldlng Safety Dlvision <br />20 Clvic Csnt€r Plaza <br />P.O. Box 1988 (lrl-19) <br />Santa Ana, CA92702 <br />(714) 647-5800 <br />www.6anta-ana.org <br />RESIDENTIAL <br />PHOTOVOLTAIC <br />CHECKLIST <br />sol{, c8c 2013 <br />Solar Photovoltalc (PV) Checkllst for Detached SINGLE FAMTLY RESTDENGES Onty <br />lnstructlons: The licensed contraclor of record shall complete all seclions, answer the t6n quostions and <br />sign the certificatio <br />minimum 11" x 17' <br />Project Address: <br />n soction below. A copy of this form shall be attached to each of TWO sels of plans, of <br />2519 Fairmont Ave, Santa Ana, CA 92706, US <br />size. lf answerinq NO to any of the questions. Dlan chsck shall be requlred. <br />2 <br />,l <br />9 <br />Contractor Company Name . Tesla Inc <br />contractor Llcense Number: 8BB 1 04 <br />trtr Are the following applicable to the proposed project? <br />Will the PV system layout provide the required threrfoot wide clear access pathways <br />per Section 605.1 1 of the California Fire Code, and is this shown on the roof plan? <br />Will th€ PV system be installed on a roof having only one roofing layer with no <br />overlays? <br />Will the PV array be flush mounted to the existing roof so that the plane of the <br />modules (panels) are parall6l to the plane of the roof? <br />Will the PV system weigh maximum 4 pounds per square feet or less? <br />Will the PV system be installed where the modules do nol overhang any roof edges <br />(such as eaves, gabled ends, ridges and hips)? <br />Will the PV system be lnstalled with a space of 2" minimum to 10" maximum between <br />the underside of modules and the surface of the rooP <br />Will the PV system be installed without using any ballast system or counter-weight <br />system? <br />Will the anchors be installed with a maximum horizontal anchor spacing of 6 feet <br />and is this maximum horizontal spacing shown on the plans? <br />Will the minimum 5/16" lag screws be installed with a minimum olz-ll?inch <br />embedment into roof rafters (with pre-drilled holes) and is this minimum embedment <br />shown on the plans? <br />Are ALL the structural pag6s of the plans WET stamped and signed by a Califomia <br />licensed professional engineer? (including proiect specific site plan, PV layout, <br />anchorage spacing, anchorage details and manufacturer's PV support information.) <br />Eltr <br />tro <br />trtr <br />@tr <br />tro <br />Eltr <br />YES NO <br />Ettr <br />Eltr <br />4 <br />5 <br />6 <br />7 <br />8 <br />10.trtr <br />I cerllfy under Penalty ol psriury undor tho laws of the State ol Callfornia that tho above ls truo: <br />print Name: Bhanu Gaddam sig nature. Bhanu swaroop caddam ffl.jtH#,if-,ti*r:x-"" <br />Phone Numb6r <br />Email Addr6ss: bgaddam@tesla.com <br />Darc, 06/22/ 18 <br />RovrS/1712015