Laserfiche WebLink
ICC <br />EVALUATION <br />SERVICE" <br />ICC-ES Evaluation Report <br />ESR-1118 <br />Reissued January 2025 This report also contains: <br />- City of LA Supplement <br />Subject to renewal January 2027 - FL Supplement <br />CITY OF SANTA ANA <br />Planning and Building Agency <br />may, lS. <br />Approved <br />FOR PERMIT ISSUANCE <br />Master ID: <br />Date: <br />ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an <br />endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or <br />other matter in this report, or as to any product covered by the report. <br />opyright © 2025 ICC Evaluation Service, LLC. All rights reserved. <br />DIVISION: 06 00 00— REPORT HOLDER: <br />WOOD, PLASTICS AND <br />COMPOSITES <br />Section: 06 17 53— <br />Shop-Fabricated Wood <br />Trusses <br />ITW BUILDING <br />COMPONENTS GROUP <br />INC. <br />1.0 EVALUATION SCOPE <br />EVALUATION SUBJECT: <br />ALPINE TRUSS PLATES <br />(METAL CONNECTOR <br />PLATES): WAVE, H AND <br />SS, TRULOX AND <br />HINGE PLATES <br />Compliance with the following codes: <br />■ 2021, 2018, 2015, and 2012 International Building Code° (IBC) <br />■ 2021, 2018, 2015, and 2012 International Residential Code° (IF <br />Property evaluated: <br />■ Structural <br />2.0 USES <br />The Alpine Truss Plates (Metal Connector Plates) described in this evaluation report are used as joint <br />connector components of light wood frame trusses. <br />3.0 DESCRIPTION <br />3.1 Wave PlateTm Truss Plate Connector: <br />The Wave PlateT"" metal truss connector plates are manufactured from No. 20 gage [minimum 0.0356 inch <br />(0.904 mm) total thickness] steel complying with ASTM A653 SS Grade 40, with a G60 galvanization coating <br />[0.0005-inch (0.013 mm) thickness on each side], and a minimum base -metal thickness of 0.0346 inch <br />(0.879 mm). The Wave Plate is also available with G90 [0.0008-inch (0.019 mm) thickness on each side] and <br />G185 [0.0016-inch (0.040 mm) thickness on each side] galvanizing levels applied to the same minimum base - <br />metal thickness steel as specified forthe G60 galvanized Wave Plate. Pairs ofteeth are punched forming slots <br />which are 0.12 inch (3.0 mm) wide and 0.50 inch (12.7 mm) long, are aligned parallel to the plate length, and <br />are spaced 0.25 inch (6.35 mm) on center across the width of the plate and 1.0 inch (25.4 mm) on center along <br />the length of the plate. Adjacent teeth are staggered along the length of the plate 0.06 inch (1.52 mm) from <br />each other in a double alternating pattern, resulting in three slot positions: centered in the row; +0.06 inch <br />(1.52 mm) from the center of the row; and -0.06 inch (1.52 mm) from the center of the row, resulting in an <br />undulating or "wave" pattern within each row of slots. The Wave PlateT"" is available in 1-inch (25.4 mm) <br />increments of both width and length. See Figure 1 for details. <br />3.2 H and SS Connector Plates: <br />H and SS connector plates are manufactured in two forms known as H (High Strength, also referred to as HS) <br />and SS (Super High Strength) from No. 20 gage [minimum 0.0356-inch (0.904 mm) total thickness] and <br />�,11 AJM <br />Page 1 of 10 <br />