2150 & 2160 E Fourth St - Plumbing & Mechanical Revision - Plan

Home Browse Search

MATERIAL AND FIXTURE SCHEDULES FIXTURE FLOW RATES (2022 CAL GREEN MANDATORY MEASURES) FIXTURE TYPE MAXIMUM FLOW RATE SHOWERHEADS, RESIDENTIAL 1.8 GPM @ 80 PSI WHEN A SHOWER IS SERVED BY MORE THAN ONE SHOWERHEAD, THE COMBINED FLOW RATE OF ALL SHOWERHEADS AND/OR OTHER SHOWER OUTLETS CONTROLLED BY A SINGLE VALVE SHALL NOT EXCEED 1.8 GPM AT 80 PSI, OR THE SHOWER SHALL BE DESIGNED TO ALLOW ONLY ONE SHOWER OUTLET TO BE IN OPERATION AT A TIME LAVATORY FAUCETS, RESIDENTIAL 1.2 GPM @ 60 PSI THE MINIMUM FLOW RATE OF RESIDENTIAL LAVATORY FAUCETS SHALL NOT BE LESS THAN 0.8 GPM AT 20 PSI. LAVATORY FAUCETS, PUBLIC AREAS 0.5 GPM @ 60 PSI KITCHEN FAUCETS 1.8 GPM @ 60 PSI KITCHEN FAUCETS MAY TEMPORARILY INCREASE THE FLOW ABOVE THE MAXIMUM RATE, BUT NOT TO EXCEED 2.2 GPM AT 60 PSI, AND MUST DEFAULT TO A MAXIMUM FLOW RATE OF 1.8 GPM AT 60 PSI. WATER CLOSETS 1.28 GALLONS/FLUSH THE EFFECTIVE FLUSH VOLUME OF DUAL FLUSH TOILETS IS DEFINED AS THE COMPOSITE, AVERAGE FLUSH VOLUME OF TWO REDUCED FLUSHES AND ONE FULL FLUSH. URINALS 0.125 GALLON/FLUSH METERING FAUCETS 0.2 GALLON/CYCLE 1. FLOW RATES ARE BASED ON THE 2022 CALIFORNIA GREEN BUILDING CODE STANDARDS SECTION 4.303 & 5.303. NOTES: THE DIAMETER OF AN INDIVIDUAL VENT SHALL NOT BE LESS THAN ONE AND ONE-FOURTH (1-1/4) INCHES NOR LESS THAN ONE-HALF (1/2) THE DIAMETER OF THE DRAIN TO WHICH IT IS CONNECTED. FIXTURE UNIT LOAD VALUES FOR DRAINAGE AND VENT PIPING SHALL BE COMPUTED FROM CALIFORNIA PLUMBING CODE TABLES 702.1 AND 702.2. NOT TO EXCEED ONE-THIRD (1/3) OF THE TOTAL PERMITTED LENGTH OF ANY VENT MAY BE INSTALLED IN A HORIZONTAL POSITION. WHERE VENTS ARE INCREASED ONE (1) PIPE SIZE FOR THEIR ENTIRE LENGTH, THE MAXIMUM LENGTH LIMITATIONS SPECIFIED IN THIS TABLE DO NOT APPLY. CPC TABLE 703.2 DRAINAGE AND VENT PIPE SIZING TABLE NOMINAL PIPE DIAMETER DRAINAGE PIPING MAXIMUM UNITS (DFU) VERTICAL 2% SLOPE 1% SLOPE DRAINAGE PIPING MAX VERTICAL LENGTH (FT) VENT PIPING HORIZONTAL AND VERTICAL (SEE NOTE) MAXIMUM UNITS (DFU) MAXIMUM LENGTH (FT) 1-1/4"1 1 45 1 45 1-1/2" 2" 3" 4" 5" 6" 8" 2 16 48 256 600 1380 3600 1 8 35 216 428 720 2640 172 342 576 2112 65 85 212 300 390 510 750 8 24 84 256 600 1380 3600 60 120 212 300 390 510 750 2 3 4 3 4 5 5 5 5 3 1 5 4 3 2 1 EXCLUDING TRAP ARM. EXCEPT SINKS, URINALS AND DISHWASHERS - EXCEEDING 1 FIXTURE UNIT. EXCEPT SIX-UNIT TRAPS OR WATER CLOSETS. NOT TO EXCEED FIVE WATER CLOSETS OR FIVE SIX-UNIT TRAPS. BASED ON ONE-FOURTH (1/4) INCH PER FOOT (2%) SLOPE. FOR ONE-EIGHTH (1/8) INCH PER FOOT (1%) SLOPE, MULTIPLY HORIZONTAL FIXTURE UNITS BY A FACTOR OF 0.8. 6 WHERE IMPRACTICAL TO MAINTAIN 1/4 INCH PER FOOT UNIFORM SLOPE, DRAINAGE PIPE FOUR (4) INCHES OR LARGER MAY HAVE A SLOPE NOT LESS THAN 1/8 INCH PER FOOT, WHEN FIRST APPROVED BY AUTHORITY HAVING JURISDICTION. 6 6 6 6 FLOW IN GPM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 FIXTURE UNITS FLUSH TANK 0 1 3 4 6 7 8 10 12 13 15 16 18 20 21 FLUSH VALVE - 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 23 24 26 28 30 32 34 36 39 42 44 46 49 51 54 5 6 7 8 9 10 11 12 13 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 56 58 60 63 66 69 74 78 83 86 90 95 99 103 107 14 15 16 18 20 21 23 25 26 28 30 31 33 35 37 -------------- ------ FIXTURE UNITS VS. GPM CONVERSION TABLE 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 111 115 119 123 127 130 135 141 146 151 155 160 165 170 175 39 42 44 46 48 50 52 54 57 60 63 66 69 73 76 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 185 195 205 215 225 236 245 254 264 275 284 294 305 315 326 82 88 95 102 108 116 124 132 140 148 158 168 176 186 195 92 94 96 98 100 105 110 115 120 125 130 135 140 145 150 337 348 359 370 380 406 431 455 479 506 533 559 585 611 638 205 214 223 234 245 270 295 329 365 396 430 460 490 521 559 FLOW IN GPM FIXTURE UNITS FLUSH TANK FLUSH VALVE FLOW IN GPM FIXTURE UNITS FLUSH TANK FLUSH VALVE FLOW IN GPM FIXTURE UNITS FLUSH TANK FLUSH VALVE FLOW IN GPM FIXTURE UNITS FLUSH TANK FLUSH VALVE FLOW IN GPM FIXTURE UNITS FLUSH TANK FLUSH VALVE 155 160 165 170 175 180 185 190 200 210 220 230 240 250 260 665 692 719 748 778 809 840 879 945 1018 1091 1173 1254 1335 1418 596 631 666 700 739 775 811 850 931 1009 1091 1173 1254 1335 1418 FLOW IN GPM FIXTURE UNITS 1583 1668 1755 1845 1926 2018 2110 2204 2298 2388 2480 2575 2670 2765 FLOW IN GPM FIXTURE UNITS FLUSH TANK FLUSH VALVE 1500 420 430 440 450 500 550 600 650 700 750 800 850 900 950 1000 2960 3060 3150 3620 4070 4480 4930 5380 5830 6280 6780 7280 7790 8300 FLOW IN GPM FIXTURE UNITS 2862 270 280 290 300 310 320 330 340 350 360 370 380 390 400 410 FLUSH TANK FLUSH VALVE FLUSH TANK FLUSH VALVE GPM EQUIVALENTS ARE BASED ON CPC CHARTS A 103.1(1) AND A 103.1(2). INSULATION WALL THICKNESS NOMINAL PIPE DIAMETER (INCHES) LESS THAN 1"2 TO <4" 1"2" 1.75"1" TO 1.5" 1.5"1.75" PIPE INSULATION THICKNESS WATER HEATING SYTEMS (105°-140° OPERATING RANGE) R 7.7 R 12.5 R 11 R 11R-VALUE 8" & LARGER4" TO <8" R 9 R 8 2"2" 1.THE INSULATION FOR HOT WATER PIPES SHALL MEET THE MINIMUM THICKNESS PER CPC 609.12 AND CEC TABLE 120.3-A OR THE MINIMUM R-VALUE PER CEC TABLE 120.3.-A. 2.INSULATION THICKNESSES SHOWN REPRESENT THE LARGER REQUIREMENT FOR DESIGNATED PIPE SIZES PER CPC SECTION 609.12 AND CEC TABLE 120.3-A. 3.THE R-VALUES FOR ALL PIPE DIAMETERS ARE BASED ON TABLE 120.3-A OF THE CALIFORNIA ENERGY CODE. GENERAL PIPE SIZING TABLES WALL CLEANOUT VENT P-TRAP GROUND CLEANOUT WYE W/CLEANOUT PLUG WYE SANITARY TEE FLOOR SINK, KITCHEN FLOOR DRAIN, SQUARE PLUMBING FIXTURES FLOOR DRAIN RISER ID TAG # TAG EQUIPMENT ID TAG CONNECT TO EXISTING VALVE SYMBOL GLOBE BALL GATE DIAPHRAGM BUTTERFLY 3-WAY 4-WAY SYMBOL REMARKS TAG # SYMBOL REMARKS PRESSURE REDUCING ANGLE GATE ANGLE GLOBE RELIEF OR SAFETY CHECK TRIPLE DUTY VALVE SOLENOID DIAPHRAGM VALVE S (NORMALLY CLOSED) VALVE (PRV) W/PURGE PORTS HOSE BIBB UNION PIPE CAP 90 DEG ELBOW DOWN 90 DEG ELBOW UP TEE, SIDE TEE, DOWN TEE, UP WATER HAMMER ARRESTER PIPING FIXTURES PIPE STUB BUILDING SUPPLY PIPE POINT OF CONNECTION BACKFLOW PREVENTOR WATER SUB-METER TWH TERMINATION CW CW HW HW HWR HW_RETURN TEXT SYMBOLS CD CONDENSATE WASTE_BELOW WASTE_ABOVE VENT RD ROOF DRAIN SUBSURFACE SD SD_ABOVE OVERFLOW OFD DRAIN STORM DRAIN PLUMBING LEGEND SYMBOL REMARKS SYMBOL REMARKS ABBREVIATIONS SYMBOL REMARKS ABOVE CONDENSATE DRAIN ABV CD HWR CW HW CPC CEC CA PLUMBING CODE CA ENERGY CODE DOMESTIC COLD WATER DOMESTIC HOT WATER DOMESTIC HW RETURN FORCED AIR UNIT FLOOR FEET PER SECOND FAU FLR FPS DN DOWN GALLONS PER MINUTEGPM TBD V TO BE DETERMINED VENT VTR W WCO VENT TO ROOF WASTE WALL CLEANOUT BELOWBLW (E)EXISTING SQ FT SQUARE FEET NEW(N) PSI POUND PER SQUARE INCH BRITISH THERMAL UNITS PER HOURBTUH CEILINGCLG SD STORM DRAIN OVERFLOW DRAINOFD POINT OF CONNECTIONPOC SOV SHUTOFF VALVE INVERT ELEVATIONIE SYMBOL REMARKS RW RECYCLED GW GREY_BELOW GW GW GREY_ABOVE GREASE WASTEGSW GROUND CLEANOUTGCO RW RECYCLED WATER GREYWATERGW SSD SUBSURFACE DRAIN WATER EQUIP GSW GREASE_BELOW GSW GSW GREASE_ABOVE FIXTURE SCHEDULE ITEM FIXTURE CO L D WA T E R HO T WA T E R WA S T E VE N T ST O R M DR A I N DESCRIPTION ICE MAKER BOX 1/2"----SELECTION TBD BY OWNER. PROVIDE WATER HAMMER ARRESTOR. PROVIDE A FIRE-RATED OUTLET BOX WHERE APPLICABLE. DISHWASHER -3/4"---DRAIN TO KITCHEN SINK. SELECTION TBD BY OWNER. PROVIDE WATER HAMMER ARRESTOR. KITCHEN SINK 3/4"3/4"2"1-1/2"-1.8 GPM FAUCET. SELECTION TBD BY OWNER. HUB DRAIN --2"1-1/2"-SIOUX CHIEF OXBOX DRAIN BOX WITH SECONDARY DRAIN FUNNEL. PROVIDE TRAP PRIMER. WATER CLOSET, FLUSH TANK 3/4"-3"2"-1.28 GPF, FLUSHTANK TYPE. SELECTION TBD BY OWNER. TUB-SHOWER COMBO 3/4"3/4"2"1-1/2"- SELECTION TBD BY OWNER.1.8 GPM SHOWER HEAD. PROVIDE A THERMOSTATIC OR PRESSURE BALANCE TYPE MIXING VALVE FOR THERMAL SHOCK AND SCALD PROTECTION. LAVATORY 1/2"1/2"2"1-1/2"-1.2 GPM FAUCET. SELECTION TBD BY OWNER. CLOTHES WASHER BOX (3 OR MORE)3/4"3/4"3"2"-SELECTION TBD BY OWNER. PROVIDE WATER HAMMER ARRESTOR. PROVIDE A FIRE-RATED OUTLET BOX WHERE APPLICABLE. FIRE SPRINKLER HUB DRAIN TRAP PRIMER -4"2"-STANDPIPE FOR FLUSHING FIRE SPRINKLER SYSTEM ELECTRONIC TRAP PRIMER 1/2"---- P.P.P NO. MPB-500 (120/60 VOLT, 6.3 WATTS), MINI-PRIME ELECTRONIC TRAP PRIMING MANIFOLD W/BOX (INSTALL PER MANUFACTURER'S RECOMMENDATIONS). TRAP PRIMER 1/2"---- PPP PR-500 PRESSURE DROP ACTIVATED TRAP PRIMER (INSTALL PER MANUFACTURER'S RECOMMENDATIONS). SELECT THE DISTRIBUTION UNIT DU-U OPTION IF CONNECTED TO TWO FLOOR DRAINS. FLOOR DRAIN --2"1-1/2"-SELECTION TBD BY OWNER. PROVIDE TRAP PRIMER. HOSE BIBB 3/4"----WALL MOUNTED WITH ATMOSPHERIC VACUUM BREAKER. ARROWHEAD ARROWBREAKER MODEL OR EQUIVALENT. MOP SINK 3/4"3/4"3"2"-SELECTION TBD BY OWNER. IMB 1 DW 1 KS 1 HD 1 WC 1 BT 1 L 1 WSH 1 SHD 1 TP 1 TP 2 FD 1 HB 1 MS 1 PIPING MATERIAL SCHEDULE DOMESTIC WATER PIPING INSIDE BUILDING ABOVE FLOOR SIZES 1/2" TO 2" UPONOR 'AQUAPEX' PEX TUBING WITH PROPEX (EP) FITTINGS, OR ALTERNATE BRANDS CONFORMING TO ASTM F876 AND ASTM F877 STANDARDS AND SDR9 DIMENSIONAL STANDARD. NOTE: 1. THE INSTALLATION OF PEX TUBING IN POTABLE WATER SUPPLY SYSTEMS MUST FOLLOW INDIVIDUAL MANUFACTURERS' INSTALLATION PROCEDURES AND THE PROCEDURES SET FORTH IN 2022 CPC SECTIONS 605.9 THRU 605.9.3. 2. PEX TUBING WHEN PLACED IN THE SOIL AND USED IN POTABLE WATER SYSTEMS INTENDED TO SUPPLY DRINKING WATER, THE TUBING SHALL BE SLEEVED WITH A MATERIAL APPROVED FOR POTABLE PAGE 3 OF 3 PERMIT TRACKING NUMBER 3014-6191-241 WATER USE IN SOIL OR MATERIAL(S) THAT ARE IMPERVIOUS TO SOLVENTS OR PETROLEUM PRODUCTS. 2022 CPC TBL. 604.1 FOOTNOTE #3. 3. PEX TUBING SHALL MEET OR EXCEED THE REQUIREMENTS OF ASTM F876-2015A WHEN USED IN CONTINUOUSLY RECIRCULATING HOT WATER SYSTEMS WHERE PEX TUBING IS EXPOSED TO THE HOT WATER 100% OF THE TIME. 2022 CPC TBL. 604.1 FOOTNOTE #4. 4. NEW POTABLE WATER SYSTEMS ARE REQUIRED TO BE DISINFECTED BY CHLORINATION. 2022 CPC SEC.609.10 (1, 2, 3, 4). SEWER, WASTE AND VENT PIPING INSIDE BUILDING ABOVE FLOOR SCHEDULE 40 PVC OR ABS PLASTIC PIPE WITH DWV TYPE FITTINGS. SEWER, WASTE AND VENT PIPING INSIDE BUILDING BELOW GRADE SCHEDULE 40 PVC OR ABS PLASTIC PIPE WITH DWV TYPE FITTINGS. 1.BUILDING DRAIN AND VENT PIPING MATERIALS SHALL COMPLY WITH CPC SECTIONS 701.0 AND 903.0. 2.ALL SANITARY SYSTEM MATERIALS SHALL BE LISTED BY AN APPROVED LISTING AGENCY. 3.ANY COPPER PIPING JOINTS UNDER CONCRETE SLAB SHALL BE BRAZED INSTEAD OF SOLDERED. 4.TYPE M COPPER TUBING MAY BE USED FOR ABOVE GROUND WATER PIPING INSIDE OR ON THE BUILDING. 5.CPVC TUBING MAY BE USED FOR CONDENSATE DRAIN PIPING WHEN DISCHARGE FROM FLUE-BURNING APPLIANCES IS ACIDIC OR CORROSIVE. 6.ALL COPPER PIPING INSTALLED BELOW GRADE SHALL BE COATED. EQUIP. NUMBER LOCATION MANUFACTURER SERIES MODEL TYPE TOTAL VOLUME ACCEPTANCE FACTOR MAX TEMPERATURE MAX PRESSURE FACTORY PRECHARGE PH Y S DA T A DIAMETER HEIGHT CONNECTION SHIPPING WEIGHT EXPANSION TANK SCHEDULE *ANY WATER SYSTEM PROVIDED WITH A CHECK VALVE OR BACKFLOW PREVENTER SHALL BE PROVIDED WITH AN APPROVED, LISTED, ADEQUATELY SIZED EXPANSION TANK OR OTHER APPROVED DEVICE HAVING A SIMILAR FUNCTION TO CONTROL THERMAL EXPANSION. AMTROL THERM-X-TROL ST-5 IN-LINE 2.0 GALLONS 0.45 200°F 150 PSIG 50 PSIG 8" 13" 3/4" NPT 5 LBS ET BY WH-1 1 WATER HEATER ROOM RHEEM PROH50 T2 RH310BM HYBRID ELECTRIC 67 26 37-145°F N/A 3.50 22-1/4"D X 61"H 172 3/4" NPT 208-240V - 1PH 24 A WH 1 HYBRID ELECTRIC WATER HEATER SCHEDULE EQUIPMENT NUMBER MANUFACTURER LOCATION MODEL TYPE WATER CONN. PH Y S DA T A WEIGHT (EMPTY) DIMENSIONS CO N N . SI Z E SUPPLY POWEREL E C . DA T A 1ST HOUR RATING GPH AMBIENT OPERATING RANGE ENERGY FACTOR (ELECTRIC) RECOVERY 90°F RISE, GPH ENERGY FACTOR (EFFICIENT) HYBRID ELECTRIC WATER HEATER SCHEDULE EQUIPMENT NUMBER MANUFACTURER LOCATION MODEL TYPE WATER CONN. PH Y S DA T A WEIGHT (EMPTY) DIMENSIONS CO N N . SI Z E SUPPLY BREAKER SIZEEL E C . DA T A 1ST HOUR RATING GPH RECOVERY 90°F RISE, GPH AMBIENT OPERATING RANGE ENERGY FACTOR (EFFICIENT) *OR APPROVED EQUAL 2 WH RHEEM* HPLD80* HYBRID ELECTRIC WATER HEATER ROOM 244 24-1/4"D X 74"H 3/4" NPT 89 29 35-145°F 3.70 208V- 1PH - 30 AMPS 30 P-0.2 MATERIAL AND FIXTURE SCHEDULES PC COMMENTS RESPONSE #1 01/29/2025A al l i d e a s , d e s i g n s a n d p l a n s r e p r e s e n t e d b y t h i s d r a w i n g a r e t h e e x c l u s i v e p r o p e r t y o f Go u v i s E n g i n e e r i n g a n d s h a l l n o t b e r e p r o d u c e d i n w h o l e o r i n p a r t w i t h o u t t h e e x p r e s s p r i o r w r i t t e n p e r m i s s i o n o f s a i d e n g i n e e r s , a n y u n a u t h o r i z e d r e u s e o f t h e s e p l a n s o t h e r t h a n f o r t h e p r o j e c t a n d l o c a t i o n s h o w n i s p r o h i b i t e d . JOB NO. SUBMITTAL DATE SHEET TITLE SHEET NO. CLIENT: REVISION DATE 21 3 0 E 4 T H S T # 2 0 0 SA N T A A N A , C A 9 2 7 0 5 BSB: MR230056; Gouvis: 66467 WATER REVISIONS 09/12/2025 1ST PLAN CHECK SUBMITTAL 08/20/2024 2ND PLAN CHECK SUBMITTAL 1/29/2025 PC COMMENTS RESPONSE #2 04/17/2025B 3RD PLAN CHECK SUBMITTAL 04/17/2025 PC COMMENTS RESPONSE #3 07/10/2025C 4TH PLAN CHECK SUBMITTAL 07/10/2025 WATER REVISIONS 09/12/2025D WATER REVISIONS 09/12/2025 PC COMMENTS RESPONSE #4 10/10/2025E CLIENT REVISIONS 10/10/20251 OL I V E C R E S T R E S I D E N T I A L 21 5 0 E . F O U R T H A N D 2 1 6 0 E . F O U R T H SA N T A A N A C A 9 2 7 0 5 OL I V E C R E S T DATE SIGNED: 7/8/25