10180865_3120 W. LAKE CTR DR. - Plan (2)

Home Browse Search

51 SIGN COMPONENTS MANUAL (SAM)October 1, 2013 LED 60€V 12P 100-277 0.8 - 0.3 12 60 LED 60CV 24P 100 - 277 | 0.8 - 0.3 || 24 || 60 3. These power supplies are only suitable for use in dry and damp locations. 4. iln the end product, power supply spacing Icl other heat producing components shall be minimum 2 inches spacing ito sidewalls and minimum 2 inches spacina to too of enclosure. Lightechim L Ughtech™LED Dr iver 4 Halogen Tron*former and model designation.Company name or trademarks GE LIGHTING SOLUTIONS LLC BLDG 338E 1975 NOBLE RD EAST CLEVELAND, OH 44112 USA E219167 Border tube kits, Includes Lens Cat. No. GExxBTL; Lens connector Cat. No. GExxBTLC: End cap Cat. No. GExxBTLEC: Exterior corner kit Cat. No. GExxBTLXC: Interior corner kit Cat No. GExxBTLIC, Base reflector Cat No GEBTBR: Base connector Cat. No. GEBTBC: Cam lock Cat. No. GEBTCL. Canopy Kits, Cat. No. GECPL (8 ft length). GECPEC (end cap), GECPLC, (lens connector), GEBTBCL, GEBTBC. Light guide kits includes· Light guide Cat. No. GEXNLGXX-XXX, Light Guide End Cap Cat. No. GEXXXNLGECZZ, XXX may be any alpha letter representing color. ZZ may be any alpha letter representing size. Light Guide Connector Cat. No. GEXXXNLGYZZ, XXX may be any alpha letter representing color, Y can be any alpha character describing the type of connector ZZ may be any alpha letter representing size.. Mounting clip Cat. No. GEXNMCXX, Supply wire Cat. No. GEXNSXX. Splice connector Cat. No. GEXNSC 1 : Weather box Cat. No. GEXWBXX-XXX. 1. Border Tube Kit, Canopy Kit and Light Guide Kit are for Wet Location only use when enclosing LED's connected to a Class 2 circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. 2. The LED border tube kit and Canopy Kit was not evaluated as an electrical enclosure. 3. The LED border tube kit and Canopy Kit was not evaluated as a watertight housing. LED power supplies, Cat. No. GEXLPS21, GEXNPS30-120, GEXNPS31-120 1. This component has been Judged on the basis of the required spacings in thei Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2.The supply terminals and connectors are'suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3.The equipment was submitted and tested for a maximum manufacturers recommended ambient (Tmra) of 40 C. 4. Leakage current measurementsshall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-useiproduct 5. The drivers are intended for installation inside an electrical enclosure. 6. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. 7. The drivers are suitable for dry location use only except the drivers Models GE)<NPS30-120 and GEXLPS21 are suitable for damp location use. LED array drivers, Models GEXLPS21-U, GEPS12-60U, GE060/MV/\/12T12T1-A 1. These components have been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equiprnent was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. The insulation system of the main isolation transformer designated (T2) in these models is a Class 105(A) insulation system. Unless the modules are mounted as specified in condition of acceptability number 7, a temperature test is required when these models installed within an electrical enclosure or raceway. 5. The maximum measured leakage current of a sihgle unit is 0.49 mA. Leakage current measurements shall be performed when multiple LED drivers are used in the final equipment or when the LED driver is used in combination with other=equipment in the end-use product. 6. The unit is intended for installation inside an electrical enclosure. 7. The unit may be used withjn an electrical enclosure or raceway without temperature testprovided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. 8. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. LED power supplies, Model GEPS24-100Ui GE100/MV/\/24T1-A. 1. This component has been judged on the basis of the required spacing in the Standard for CIass 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturers recommended ambient (Tmra) of 40 C. 4. This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an electrical enclosure or raceway. 5. Leakage current measurements shall be performedi when more than four LED drivers are used in tbe equipment or when the LED driver is used in combination with other equipment in the end-use product. 6. The unit is intended for installation inside an electrical entlosure. 7. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. LED array drivers, Models GEPS 12-20, GERS 24-20. 1. The maximum measured output voltage, current and power at the; output of these models was found in compliance with the limits for Class 2 output requirements. 2. The transformers of these units employ Class 105 insulation system. 3. These components were intended for use in indoor Dr'y and DAMP location only.