Laserfiche WebLink
- 1 <br />PART 1 - GENERAL· 1 4- <br />1.1 SUMMARY <br />A. WORK INCLUDES <br />1. Green Fasten solar attachment bracket that <br />attaches directly to the roof deck. <br />/ 2. Provide appropriate bracket and fasteners <br />for the roof system. <br />B. RELATED SECTIONS <br />1. Section 07600: Flashing and Sheet Metal <br />2. Section 07500: Roofing <br />3. Division 1:Administrative and Procedural <br />Requirements <br />4. Division/.Thermal and Moisture Protection <br />1.2 SYSTEM DE5CRIPTION <br />A. COMPONENTS: <br />1. GreenFasten GF1 system consists of alumi- <br />num flashing with integral EPDM bushing <br />< and one bonded stainless steel and EPDMwasher. <br />2. Fasteners <br />A. To beof metal compatible with aluminum <br />GreenFasten components. <br />B. Fasteners should be selected for compat- <br />h /1 n ibility with the roof deck. <br />1 C.Fastener strength should exceed or be <br />equal <br />to that of the allowable load of the system <br />See test data at www.ecofastensolar.com <br />. Sealant (if required by roof manufacturer): <br />to be roof manufacturer approved. <br />. Aluminum compression bracket <br />B. DESIGN REQUIREMENTS: <br />1. Bracket spacing to be recommended !by <br />project engineer. <br />2. Installa minimum ofone fastenerper <br />assembly. <br />3. It is important to design new structures or <br />assess existing structures to make sure that <br />they can withstand retained loads.i '<n n 11 <br />*ga? <br />3 <br />4 <br />alu 1% E <br />1.3 SUBMITTAL <br />A. 5ubmit manufacturer's written specifications. <br />B. Submit standard product cut sheets. <br />C. Submit installation instructions, <br />D. Submit product specific load test data, showing <br />ultimate and allowable load values. <br />1.4 QUALITYASSURANCE <br />Installer to be experienced in the installation of <br />specified roofing material for no less than 5 years in <br />the area of the project. <br />1.5 DELIVERY / STORAGE / HANDLING <br />Inspect material upon delivery. Notify manufacturer <br />within 24 hours of any mi5sing or defective items. <br />Keep material dry, covered, and offthe ground until <br />installed. <br />PART 2 - PRODUCTS <br />2.1 MANUFACTURER <br />EcoFasten Solar' <br />289 Harrel Street Morrisville, VT 05661 <br />(877) 859-3947 <br />www.ecofastensolar.com <br />2.2 MATERIALS <br />A. Attachment Bracket <br />6000 Series Aluminum <br />1. Comp SIide 4"Bracket <br />B. Fasteners (may be supplied by others) to be <br />compatible with chosen roof application and <br />meet specified pull out values as shown in load <br />test data. <br />Specifications <br />C. Base flashing is.032 gauge aluminum em- <br />bossed <br />to accept EPDM bushing. <br />D. Bushing is EPDM. <br />E. Stainless steel bonded washer is 30418.8 stain- <br />less and EPDM. <br />23 FINISH - Mill Finish <br />A. Brad<etis mill finish aluminum <br />8. Base flashing (thoose one) <br />1. Black - kynar painted <br />PART 3 - EXECUTION <br />3.1 EXAMINATION <br />A. Substrate: Inspect structure on which brackets <br />are to be installed and verify that it will <br />withstand anyadditional loading that may be <br />incurred. <br />B. Notify General Contractor of any deficiencies <br />before installing EcoFasten Solar brackets, <br />C. Verify that roofing material has been installed <br />correctly prior to installing Solar attachment <br />brackets. <br />3.2 INSTALLATION <br />A. Comply with architectural drawings and proj- <br />ect engineer's recommendations for location <br />of system. Comply with Manufacturer's written <br />installation instructions for installation and <br />layout. <br />--877-859-3947 Committed to the Support o f Renewable Energy © Ecofasten Solar- All content protected under copyright All rights reserved. 04/8/14 4.1 <br />ru <br />¥