|
53 SIGN COMPONENTS MANUAL (SAM)October 1, 2013
<br />PM, PMD = Power Max
<br />MH, MXH, MXHL =MAX HO
<br />BS Shallow Box single sided
<br />BD =Shallow Box double sided
<br />BIH = Edgestrip
<br />Third set of "XX" denotes Light Strip final assembly as noted below:
<br />LA =Light Strip, assembled inside a plastic rod, 8 inch section
<br />LE =Light Engine means same as Light strips
<br />AA =Light.engine, assembled inside a plastic rod, 16)nch section ._ *.
<br />SX or X =Number of LEDs per foot where Xisl=6 LEDs per foot etc. (X can be representative of lt09 digits)
<br />\AD(X =Wide Angle light diffuser, where the first X describes the PCB length, A for regular and L for long, and the
<br />second X is an a!pha numeric character of leds per foot.
<br />PX =For PowerGrid (PG), Power Strip (SS) and Double Sided Power Strip (DS) only, where x equals the
<br />number of LEDs per foot. Not Assembled in Tube. An optional X may be added to denote wire length
<br />between modules where X is S for short, M for Medium, and L for Long.
<br />XX =only to be used with DS product line, xx is number that correlates to total length in inches (48 = 48")
<br />assembled in acrylic tube.
<br />"XXX" denotes any alphanumeric character that denotes the Color Temperature of the LEDs i.e. 65k = 6500,75k = 7500 etc.
<br />Splice connector, Cat. No. GexxSCx: End caps, Cat. No. GexxECx.
<br />1. These products are only suitable for connection to a Class 2 power source.
<br />2. When units are connected to a Class 2/"LPS" circuit, they are not to draw a total wattage of greater than the secondary or
<br />output rating of the Class 2/"LPS" supply.
<br />3. These products are suitable for use in dry, damp and wet locations.
<br />4. These products described in this section may be cut into segments per manufacture insulation instructions.
<br />5. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions
<br />of Use" as defined in the Sign Components Manual.
<br />6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end
<br />use product.
<br />LED Controller, LED Tetra FX Special Lighting Effects Controller, Cat. No. GEFX 1
<br />1. This product is suitable for only when connected to a Class 2 power source or LSP, Model GEXLPS20, GEXLPS21, GEXNOS30
<br />or GEXNPS31 by GE. Rated Input is 12/24 V dc, Output is 12/24 V dc.
<br />2. This product is a Class 2 device suitable for use in dry, damp and wet locations.
<br />3. The controller shall be provided in a suitable housing when use in wet locations.
<br />4. Lead wires are FUC (AVLV2), Style 2651, rated 105 C, 300V. Not suitable for use inside walls, above ceiling or other similar
<br />concealed spaces unless mounted inside an electrical enclosure.
<br />5. The controller is provided with a DMX 5-pins input connector. The pin arrangements in the connector shall always be the same.
<br />The DMX controller is capable of providing the 4 channel dimming, flashing, chasing, sequencing, color mixing, and color
<br />changing functions.
<br />LED wire, Cal. No. GExxSWx. Nomenclature for Splice Connectors, LED Wires, End Caps: xx denotes product line, CL = channel
<br />letter, DS = double sided, XL = tetra long strip, PT = power tetra, XN = Exposed Neon, TM = Mini, MX = Max, TU = Ultra, PG =
<br />Power Grid, PX = Power White XL, PH = Power White HO, XH = Power White XL HO, MM = Mini Max; 'x' denotes design revision
<br />number.
<br />1. These products are only suitable for connection to a Class 2 power source.
<br />2. When units are connected to a Class 2/"LPS" circuit, they are not to draw a total wattage of greater than the secondary or output
<br />rating of the Class 2/"LPS" supply.
<br />3. These products are suitable for use in dry, damp and wet locations.
<br />4. These products described in this section may be cut into segments per manufacture insulation instructions.
<br />5. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions of
<br />Use" as defined in the Sign Components Manual.
<br />6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end
<br />use product.
<br />LED power supplies, Models GECLPS4.
<br />1. LED power supply, Catalog No. GECLPS4 for dry and damp locations.
<br />2. Each power supply output is Class 2.
<br />LED power supplies, Models GECLPS4O.
<br />1. LED power supply, Catalog No. GECLPS4O for dry and damp locations.
<br />2. Each power supply output is Class 2.
<br />LED power supplies, Models GECLPS6 and GECLPSPHA.
<br />1. LED power supply, Catalog No. GECLPS6 for dry and damp locations.
<br />2. Each power supply output is Class 2.
<br />LED power supplies, Models GECLPS3.
<br />1. LED power supply, Cat. No. GECLPS3 for dry and damp locations.
<br />2. Each power supply output is Class 2.
<br />LED power supplies, Models GECLPS5, GECLPSPH, GECLPSPW, GECLPSWH.
<br />1. LED power supply, Cat. No. GECLPS5, GECLPSPH, GECLPSPW and GECLPSWH for dry and damp locations.
<br />2. Each power supply output is Class 2.
<br />Power supplies with Class 2 outputs, Models GEPS24-80, GEPS12-60, GEPS24-20.
<br />1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp
<br />locations.
<br />2. These power supplies need to be installed in an enclosure with a means for the connection to conduit.
<br />3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than
<br />13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110°C. Similarly, for Model
|