Laserfiche WebLink
Installation Manual: MEMC Silvantis 60 cell PV Modules 10 of 15 <br />5,4 ELECTRICAL INSTALLATION WARNINGS <br />Installation and maintenance should be performed by qualified personnel only. <br />Use insulated tools during installation, troubleshooting and maintenanceof photovoltaic rrodules. <br />Installers should adhere to all applicable local, regional, and national codes and regulations when designing and constructing <br />the photovoltaicsystem. <br />Photovoltaic modules.produce DC electrical energy from light. When illuminated, each madole can have a DC potential of <br />greater than 45V ahd should be handled with care. <br />Disconnecting modules under illumination may cause electrical arcing which may result in burns, fires, orother problems. <br />Modules connected in series should·not be disconnected under illumination. - <br />Always use a wire management„system that keeps wires and cables out of direct contact with edge surfaces which could cut <br />or damage the insulation. Do not allow wires to rest on the ground or roof surface. <br />The module junction box should not beopened or modified irl any way·in the field. <br />Additional grounding holes may be'added only, with the express written consent of MEMC. New grounding holes must be <br />drilled using an approved drill jig, avoiding damage to the module glass, backsheet or other module components. <br />Do not use mirrors, lenses, or other techniques to magnify or concentrate additional light on the module. <br />6.0 DISCLAIMER OF LIABILITY <br />The information in this manual is based on MEMC's knowledge and experience and is believed to beaccurate. However, all <br />information in this manual (without exception) including recommendations and specifications does notconstitute a warranty, <br />expressed or implied. MEMC reserves the right to changethe manual, the rhodule, or specifications without prior notice. <br />The product warranty shall be VOID if handling and installation of the productdoes not conform to MEMC's written installation <br />instructions, or ifthe p'roduct has been reworked, repaired or otherwise modified in a manher not previously authorized by MEMC in <br />writing, or if the product is installed in an envi fonment for which it was not designed. MEMC shall not be liable for special, indirect, <br />consequential, contingentor incidental damages relatedto orarising from the installation or useof the.product by purchaser under <br />ally LII LU, i,Sla Ces. - <br />MEMC assumes no responsibility for any product application or use which is beyond MEMC's direct control. MEMC does not accept <br />responsibility and expressly disclaims liability for loss, damage, orexpensearising out of or in any wayconnected to such installation, <br />operation or maintenanceof theiproduct. <br />International Product Certifications: <br />IEC 61215, IEC61730, CE, UL 1730, and Safety Class Il certificationsensurethat MEMC solar products operate safelrand comply with <br />global electrical, eerformance, reliability, and fire safety codes. <br />EFFiftizil«=7yi'.912--Pli ':22:1 , IEG4 215 ced·{fied41<PQ\/·SUD Ej-·phsuielorigill¢rfi,-6per€i6-n iA.i)·0#Fiety·?f ¢l(mal,i¢ff-,,1.1 <br />22222&1.linaLE 't-'-·'Of?foi-ik'e:31,·-239%5%23-3,=nd'08.--.i --'-·:-=I "-A.·j... -·····-j' '. t· . -' ''' 'I;''-..7- :il <br />6/milads/Nfagia.:'.663 19·,V·24' <br />C l <br />APPROVED PRODUCT <br />I,•TICN <br />MEMC Modules are certified by: <br />JS <br />A MCS B .B T PV CYCLE <br />© Copyright 2012 MEMC Electronic Material <br />1 <br />f