Laserfiche WebLink
CONTROLLER <br />R1=M1101,,,,,,,,I.tJT10N 121 - R-,[4. <br />R1Df01,,,,,,,,ILJT10N 121 <br />RevPi Connect S of <br />RevPi Connect S <br />CE �A O <br />Technical Data - `�` mom <br />Number of digital output channels 1 <br />Article No.: 100362 (8 GB version) <br />Output type Relay contact, approval up to 30 V switching voltage (e.g. for <br />Article No.: 100363 (16 GB version) <br />power supply of a router) <br />Article No.: 100364 (32 GB version) <br />Maximum current load of the contact 2 A @ 30 V DC (resistive load!) <br />Software interface of input and output Via GPIOs and process image. Output is optionally switched by <br />Housing dimensions (H x W x D) 96 x 45 x 110,5 mm <br />hardware watchdog. <br />Housing type DIN rail housing (for DIN rail version EN 50022) <br />Hardware watchdog functionality Can be disabled by bridging the 4-pole screw -type terminal. Re- <br />set by toggling a GPIO or alternatively a bit in the process im- <br />Housing material Polycarbonate <br />age.. <br />Weight approx 197 g / 224 g (incl. connectors) <br />Hardware watchdog interval) Trigger after approx. 60 seconds without toggling the reset <br />it. <br />Protection class IP20 <br />Compatible modules for system expansion All RevPi 10 modules and RevPi Gate modules can be con - <br />Power supply 12 ... 24 V DC -15 % /+20 %, reverse -polarity protected <br />nected via the PiBridge system bus. <br />Max. power consumption 20 Watt (incl.1 A total USB output current) <br />All RevPi Con modules can be connected via the ConBridge sys- <br />tem bus. <br />Allowable operating temperature -25 ... +55 °C <br />— <br />ESD protection 4 kV / 8 kV (according to EN61131-2 and IEC 61000-6-2) <br />Allowable storage temperature -40 ... +85 °C <br />- <br />EMI tests Passed (according to EN61131-2 and IEC 61000-6-2) <br />Max. relative humidity (at 40 °C) up to 93 % (non -condensing) <br />Surge/Burst tests Passed (according to EN61131-2 and IEC 61000-6-2) <br />Interfaces 2 x USB A (Total current draw from both sockets max.1 A) Z <br />Buffer time RTC min. 24 h <br />2 x RJ4510/100 Ethernet (using separate MAC addresses) <br />1 x RS485 screw -type terminal <br />Optical indicator 6 status LEDs (bi-color), two of them freely programmable <br />Conformity CE, RoHS <br />1 x Micro-USB (solely for image transfer to eMMC) <br />1 x Micro HDMI 2.Oa (4K) <br />UL certification Yes, UL-File-No. E494534 <br />1 x PiBridge system bus <br />Note: The device may only be supplied from circuits that com- <br />1 x ConBridge system bus <br />ply with Class 2 or Safety Extra Low Voltage (SELV) according <br />to Class 9.4 of UL 61010-1. <br />Connectors 1 x 4-pole screw -type terminal for relay contact and signal in- <br />The average power consumption without USB load varies greatly and depends on the use of the interfaces, the GPU and the <br />put <br />CPU. It is usually well below 4 watts without HDMI. <br />1 x 4-pole screw -type terminal for power supply <br />z 1 A USB output current (total of both USB outputs) is only available for input voltages >11 V. The bridging time required by EN <br />61131-2 of voltage dips of at least 10 ms is only guaranteed with a supply voltage of 20.4 to 28.8 V. At 12 V input voltage this <br />Processor Broadcom BCM2711, quad -core Arm Cortex-A72 <br />time decreases drastically, especially when driving loads by USB ports. <br />Clock rate 1.5 GHz <br />Processor cooling Passive with heat sink <br />RAM 1 GB LPDDR4 <br />Flash memory 8 GB (Article No.: 100362), 16 GB (Article No.: 100363), 32 GB <br />N100364 ) <br />(Atil(Article o.: <br />Collins Electrical Company, Inc. <br />project 249003 <br />purchase order #2490035016 <br />Number of digital input channels 1 <br />Digital input type 24 V control voltage (e.g. for power -good signal of a UPS) <br />Input thresholds approx. 3.0 V (0 -> 1) resp. 2.3 V (1 -> 0) <br />Input protection against overvoltage, negative voltages <br />Errors and omissions excepted. <br />KUNBUS GmbH, Heerweg 15C, 73770 Denkendorl', Germany 1 Tel: +49 (0) 711 400 91 500 1 Fax: +49 (0) 711 400 91 501 1 V 1.2 <br />Email: info@kunbus.de I Web: www.kunbus.com 1/2 <br />Errors and omissions excepted. <br />KUNBUS GmbH, Heerweg 15C, 73770 Denkendorf, Germany I Tel: +49 (0) 711 400 91 500 1 Fax: +49 (0) 711 400 91 501 I V 1.2 <br />Email: info@kunbus.de I Web: www.kunbus.com 2/2 <br />E-4 <br />COND. CALCS <br />E-5 <br />LOAD CALCS <br />SS-1 TO 2 <br />SPECS SHEET <br />REVISION <br />REV NO. <br />DESCRIPTION <br />DATE <br />Q <br />UPDATED ADA NOTE <br />04/20/25 <br />Qz <br />UPDATED THE SITE PLAN TO <br />05/27/25 <br />INDICATE CORRECT ADDRESS FOR <br />PROPERTY 3121 AND THE LEGAL <br />PROPERTY LINES <br />Q <br />UPDATED LINE DIAGRAM TO <br />05/27/25 <br />REFLECT DETAILED GROUNDING <br />SYSTEM <br />CITY STAMP <br />--_z COIL <br />//III`` <br />COIL INC. <br />1307 HAYES ST. SUITE 5 <br />SAN FRANCISCO, CA 94117 <br />CALIFORNIA LICENSE 814779 <br />SPECS SHEET <br />SCALE: AS NOTED <br />DESIGNED BY: COIL INC <br />SHEET NO. <br />DATE DRAWN: MAY 27 2025 <br />SS-2 <br />PAPER SIZE: 18"x24" <br />REV C <br />