301 N Broadway - Apt TI - Plan - Laserfiche WebLink

Home Browse Search

SEE SCHEDULE SEE SCHEDULE SEE SCHEDULE SEE SCHEDULE SEE SCHEDULE SEE SCHEDULE SEE SCHEDULE EQ EQ SEE SCHEDULE SEE SCHEDULE EQ EQ AMENITY LEVEL 6 + 7 A1.2 A1.3 UNIT INTERIOR PANTRY & LINEN & WARDROBE U 3.2 AMENITY LEVEL 6 + 7 G 3.4 UNIT INTERIOR BATHROOM BEDROOM WALK-IN CLOSET U 2.1-2.2 UNIT INTERIOR WASHER & DRYWER CLOSET U 4.2 1. DOOR THRESHOLDS TO BE 1/2" THICK MAXIMUM TYPICAL. A FLOOR OR LANDING SHALL BE NOT MORE THAN 1/2" LOWER THAN THE THRESHOLD OF THE DOORWAY. CHANGE IN LEVEL BETWEEN 1/4" AND 1/2" SHALL BE BEVELED WITH A SLOPE NOT GREATER THAN 1:2. EXCEPT FOR CURBS AT ROOF LEVEL DOORS (RFM). 2. EXIT DOORS SHALL BE OPENABLE FROM THE INSIDE WITHOUT THE USE OF A KEY, SPECIAL KNOWLEDGE OR EFFORT. SURFACE-MOUNTED FLUSH OR SURFACE BOLTS ARE PROHIBITED. AUTOMATIC FLUSH BOLTS ARE ALLOWED ON PAIRS OF DOORS, PROVIDED THE DOOR WITH THE FLUSH BOLT HAS NO KNOBS OR SURFACE-MOUNTED HARDWARE AND THE UNLATCHING OF ANY LEAF REQUIRES ONLY A SINGLE OPERATION. 3. DOOR FRAMES AND HARDWARE FOR RATED DOORS SHALL BE LISTED FOR THOSE RATINGS. ALL FIRE RATED DOORS SHALL BE PROVIDED WITH AN AUTOMATIC DOOR CLOSER. SEE SHEET R1.A0.032-.033 FOR REQUIRED FIRE RATINGS FOR DOORS AND SHUTTERS. 4. FIRE DOORS SHALL HAVE AN APPROVED LABEL OR EXISTING MARK INDICATING THE FIRE-PROTECTION RATING, WHICH IS PERMANENTLY AFFIXED AT THE FACTORY WHERE FABRICATION AND ASSEMBLY ARE DONE. 5. ALL 20-MINUTE RATED ASSEMBLIES SHALL BE PROVIDED WITH APPROVED GASKETING MATERIAL SO INSTALLED TO PROVIDE A SEAL WHERE THE DOOR MEETS THE STOP ON BOTH SIDES AND ACROSS THE TOP. THE DOOR AND FRAME SHALL BEAR AN APPROVAL LABEL OR OTHER IDENTIFICATION SHOWING THE RATING THEREOF, FOLLOWED BY THE LETTER "S". 6. FIRE-RATED DOOR FRAMES SHALL BE INSTALLED STRICTLY PER MANUFACTURER'S PRINTED INSTRUCTIONS. MANUFACTURER'S PRINTED INSTRUCTIONS SHALL BE MADE AVAILABLE TO THE INSPECTING AUTHORITIES. 7. FURNISH DOOR STOPS FOR ALL DOOR LEAFS. IN EVENT SCHEDULED WALL OR FLOOR BUMPER CANNOT BE USED EFFECTIVELY, FURNISH OVERHEAD STAY. 8. PROVIDE DOOR HINGES FOR: A. DOORS OVER 60 INCHES OR LESS = 2 BUTTS B. DOORS OVER 60 INCHES AND NOT OVER 90 INCHES = 3 BUTTS (86 INCHES FOR FIRE-RATED DOORS). C. DOORS OVER 90 INCHES AND NOT OVER 120 INCHES (116 INCHES FOR FIRE-RATED DOORS) = 4BUTTS 9. PROVIDE WEATHERSTRIPPING AND SEALS FOR EXTERIOR DOORS AT JAMBS, HEAD AND DOOR BOTTOM. 10.DOOR THICKNESS SHALL BE 1 3/4" TYP. U.N.O. 11.DOORS INSTALLED IN SMOKE AND FIRE SEPARATIONS SHALL BE AUTOMATIC BY THE ACTUATION OF SMOKE DETECTORS INSTALLED BY APPLICABLE CODES OR BY LOSS OF POWER TO THE SMOKE DETECTOR OR HOLD-OPEN DEVICE. 12. DOOR FRAMES SHALL BE HOLLOW METAL, U.N.O. 13.ALL DOORS INTO WASHROOMS AND JANITOR CLOSETS SHALL HAVE 2" WIDE STONE THRESHOLDS WITH BEVELED EDGES. COLOR T.B.D. BY ARCHITECT. 14.CONTRACTOR TO COORDINATE DOOR HARDWARE AND HARDWARE COUNT TYPICAL. ANY NON-COMPATIBLE HARDWARE IN THE SAME HARDWARE GROUP TO BE BROUGHT IMMEDIATELY TO THE ARCHITECT'S ATTENTION. 15.HARDWARE SCHEDULE IS A GUIDE ONLY. FURNISH ALL HARDWARE AS REQUIRED FOR THE PROJECT. HARDWARE REQUIRED FOR ANY PARTICULAR LOCATION, BUT NOT SPECIFIED SHALL BE THE SAME AS THAT SPECIFIED FOR SIMILAR LOCATIONS. ALL DOORS SHALL BE COVERED BY A LISTING OF HARDWARE IN THE FINISH HARDWARE SCHEDULE WHETHER SPECIFIED OR NOT. 16.REFER TO DRAWINGS FOR LOCATION OF SANITARY FACILITY SIGNAGE TYPICAL. 17.REFER TO DRAWINGS FOR REQUIRED CLEARANCES AT DOOR SWINGS TYPICAL. ANY DISCREPANCIES BETWEEN THE FLOOR PLANS AND THE DETAILS SHOULD BE BROUGHT TO THE ARCHITECT'S ATTENTION PRIOR TO THE START OF WORK. 18.CONTRACTOR TO VERIFY & COORDINATE ROUGH OPENING DIMENSIONS IN CONCRETE AND CMU WALLS IN THE FIELD PRIOR TO DOOR FABRICATION. 19.PROVIDE NO PAINTED OR PRIMED-FOR-PAINT HINGES. ALL HINGES TO BE FACTORY FINISHED. PROVIDE BRUSHED SS FINISH AT EXTERIOR DOORS AND EQUAL CHROME FINISH AT INTERIOR DOORS TYPICAL. 20.SEE MECHANICAL DRAWINGS FOR REQUIRED DOOR UNDERCUTS TYPICAL. INDICATE ON SHOP DRAWINGS. DO NOT USE TRANSFER GRILLES AT DOORS UNLESS APPROVED BY THE ARCHITECT. 21. ALL TRANSFORMERS REQUIRED FOR ELECTRIFIED HARDWARE TO BE CONCEALED BEHIND FLUSH ACCESS PANELS TYPICAL. CONTRACTOR TO INDICATE ON SHOP DRAWINGS ACCESS PANEL LOCATIONS FOR ARCHITECT'S REVIEW. ELECTRICAL CONTRACTOR TO COORDINATE REQUIREMENTS WITH SECURITY AND DOOR HARDWARE CONTRACTORS PRIOR TO INSTALLATION. 22.THE FORCE FOR PUSHING OR PULLING OPEN INTERIOR SWINGING EGRESS DOORS, OTHER THAN FIRE DOORS, SHALL NOT EXCEED 5 POUNDS. FOR OTHER SWINGING DOORS, AS WELL AS SLIDING AND FOLDING DOORS, THE DOOR LATCH SHALL RELEASE WHEN SUBJECTED TO A 15 POUND FORCE. THE DOOR SHALL BE SET IN MOTION WHEN SUBJECTED TO A 30 POUND FORCE. THE DOOR SHALL SWING INTO A FULL-OPEN POSITION WHEN SUBJECTED TO A 15 POUND FORCE. 23.EXIT DOORS SHALL SWING IN THE DIRECTION OF TRAVEL WHEN SERVING 50 OR MORE PERSONS AND IN ANY HAZARDOUS AREA. 24.PROVIDE SAMPLES UPON REQUEST. 25.CONTRACTOR TO PROVIDE ELECTRIFIED HARDWARE AND DEVICES AS REQUIRED TO COMPLETE THE SECURITY SYSTEM AND POWER OPERATED DEVICE INSTALLATION. CONTRACTOR TO PROVIDE AND COORDINATE ACCESS PANELS REQUIRED FOR ELECTRIFIED HARDWARE OR SECURITY DEVICES. CONTRACTOR TO PROVIDE LAYOUT PLANS FOR ARCHITECT'S REVIEW. 26.FOR EXTERIOR DOORS THAT ARE PART OF A CURTAINWALL SYSTEM ALL WIRING FOR ELECTRIFIED AND SECURITY DEVICES TO BE CONCEALED WITHIN THE MULLIONS TYPICAL. 27.PANIC DEVICES TO BE PROVIDED AS REQUIRED TO MEET APPLICABLE CODES. 28.SMOKE SEALS TO BE PROVIDED PER APPLICABLE CODES. 29.DOORS SCHEDULED AS SMOKE DOORS TO BE DOOR HARDWARE + GASKET ASSEMBLIES MEETING THE TESTING CRITERIA OF UL 1784 & NFPA 105 30.ALL DOOR SIZES SHOWN ON THE DOOR SCHEDULE ARE OPENING SIZES. PROVIDE ALLOWANCE FOR THRESHOLDS, FRAMES, ETC. 31.ALL DOORS AND FRAMES SHALL BE REINFORCED FOR CLOSERS, STOPS AND HARDWARE. 32.ALL FIRE RATED DOORS SHALL BE GASKETED AT HEAD AND JAMBS. 33.CONTRACTOR SHALL VERIFY ALL CONCRETE AND MASONRY OPENINGS IN THE FIELD PRIOR TO THE FABRICATION OF DOORS AND FRAMES. 34.ALL LEGAL EXIT DOORS SHALL BE OPENABLE FROM THE INSIDE WITHOUT THE USE OF A KEY OR ANY SPECIAL KNOWLEDGE OR EFFORT AND SHALL SWING IN THE DIRECTION OF EGRESS. SPECIAL LOCKING DEVICES SHALL BE AN APPROVED TYPE. 35.AIR LEAKAGE AT EXTERIOR DOORS SHALL BE LIMITED PER THE FOLLOWING: A. ALL DOORS SHALL BE PROVIDED WITH A SEAL, ASTRAGAL OR BAFFLE AT THE HEAD, SILL, AND JAMBS. B. DOORS REQUIRING VERTICAL OR HORIZONTAL TRACK AND GUIDES SHALL USE A CONTINUOUS MOUNTING ANGLE, SEALED IN ACCORDANCE WITH ITEM "e" LISTED HERE. C. MEETING RAILS OF SECTIONAL DOORS AND MEETING STILES OR RAILS OF BI-PARTING DOORS SHALL BE PROVIDED WITH A SEAL, ASTRAGAL OR BAFFLE. D. SWINGING AND REVOLVING DOORS SHALL BE WEATHER-STRIPPED AT THE HEAD, SILL AND JAMBS. 36.ALL FIRE RATED DOORS WHICH OPEN INTO EXIT ENCLOSURES OR EXIT PASSAGEWAYS SHALL BEAR MANUFACTURES LABEL INDICATING A MAXIMUM 450 DEGREE F TEMPERATURE RISE ON THE EXPOSED SIDE. 37.GLAZING WITHIN DOORS AND SIDELIGHTS WITHIN 24" SHALL COMPLY WITH CBC SECTION 2406. 38.NOT USED 39. ALL PIN-TYPE DOOR HINGES ACCESSIBLE FROM OUTSIDE SHALL HAVE NON-REMOVABLE HINGE PINS. HINGES SHALL HAVE MIN. 1/4" DIA. STEEL JAMB STUD WITH 1/4" MIN. PROTECTION. THE STRIKE PLATE FOR LATCHES AND HOLDING DEVICE FOR PROJECTING DEADBOLTS IN WOOD CONSTRUCTION SHALL BE SECURED TO THE JAMB AND THE WALL FRAMING WITH SCREWS NO LESS THAN 2-1/2" LONG. 40.CYLINDER GUARDS SHALL BE INSTALLED ON ALL CYLINDER LOCKS WHENEVER THE CYLINDER PROJECTS BEYOND THE FACE OF THE DOOR OR IS OTHERWISE ACCESSIBLE TO GRIPPING TOOLS. 41.DEADBOLTS SHALL HAVE HARDENED INSERTS. DEADLOCKING LATCH WITH KEY-OPERATED LOCKS SHALL BE PROVIDED ON EXTERIOR. LOCKS SHALL BE OPENABLE WITHOUT KEY, SPECIAL KNOWLEDGE, OR SPECIAL EFFORT FROM THE INTERIOR. 42.STRAIGHT DEADBOLTS SHALL HAVE A MIN. THROW OF 1" AND AN EMBEDMENT OF NOT LESS THAN 5/8", AND A HOOK- SHAPED OR AN EXPANDING-LUG DEADBOLT SHALL HAVE A MINIMUM THROW OF 3/4" . 43.LATCHING AND LOCKING DOORS THAT ARE HAND ACTIVATED AND WHICH ARE IN A PATH OF TRAVEL SHALL BE OPERABLE WITH A SINGLE EFFORT BY LEVER TYPE HARDWARE, PANIC BARS, PUSH-PULL ACTIVATING BARS OR OTHER HARDWARE DESIGNED TO PROVIDE PASSAGE WITHOUT REQUIRING THE ABILITY TO GRASP THE OPENING HARDWARE. 44.THE BOTTOM 10" OF ALL DOORS EXCEPT AUTOMATIC AND SLIDING DOORS SHALL HAVE A SMOOTH UNINTERRUPTED SURFACE TO ALLOW THE DOOR TO BE OPENED BY A WHEELCHAIR FOOTREST WITHOUT CREATING A TRAP OR HAZARDOUS CONDITION. WHERE NARROW FRAME DOORS ARE USED, A 10" HIGH SMOOTH PANEL SHALL BE INSTALLED ON THE PUSH SIDE OF THE DOOR, WHICH WILL ALLOW THE DOOR TO BE OPENED BY A WHEELCHAIR FOOTREST WITHOUT CREATING A TRAP OR HAZARDOUS CONDITION. 45.DOORS OPENING INTO REQUIRED 1-HOUR FIRE-RESISTIVE CORRIDORS SHALL BE PROTECTED WITH A SMOKE OR DRAFT-STOP FIRE ASSEMBLY HAVING A 20-MINUTE RATING, AND SHALL BE SELF CLOSING. 46.ALL EGRESS DOOR OPERATION SHALL ALSO COMPLY WITH CBC SECTION 1008.1.9-1008.1.9.7. 47. G.C. TO PROVIDE COMPLETE DOOR/HARDWARE PACKAGE TO FUNCTION AS INDICATED. ALL DOORS AND HARDWARE SHALL BE BUILDING STANDARD, U.O.N. SUBMIT COMPLETE SPECS TO ARCHITECT FOR REVIEW AND APPROVAL. 48. ALL HARDWARE TO MEET TITLE 24 AND ACCESSIBILITY REQUIREMENTS. SEE MOUNTING HEIGHTS ON SHEET R1.G0.032 49. THE BOTTOM 10" OF ALL DOORS EXCEPT AUTOMATIC AND SLIDING SHALL HAVE A SMOOTH, UNINTERRUPTED SURFACE TO ALLOW THE DOOR TO BE OPENED BY A WHEELCHAIR FOOTREST WITHOUT CREATING A TRAP OR HAZARDOUS CONDITION (CBC SEC. 11B-404.2.10) 50. ALL GLAZING SHALL BE TEMPERED, ALL EXPOSED EDGES SHALL BE POLISHED. GLAZING WITHIN A 24" ARC OF EITHER SIDE OF DOORS MUST BE OF SAFETY GLAZING MATERIAL (CBC SEC. 2406). 51. HAND-ACTIVATED DOOR OPENING HARDWARE SHALL BE CENTERED BETWEEN 34" AND 44" A.F.F. (CBC SEC. 11B-404.2.7 ) LATCHING AND LOCKING DOORS THAT ARE HAND ACTIVATED AND ARE IN THE PATH OF TRAVEL SHALL BE OPERABLE WITH A SINGLE EFFORT BY LEVER-TYPE HARDWARE, PANIC BARS OR OTHER HARDWARE DESIGNED TO PROVIDE PASSAGE WITHOUT REQUIRING THE ABILITY TO GRASP THE HARDWARE. (CBC SEC. 11B-309.4). ABREVIATIONS LIST: AL = ALUMINUM BRZ = OIL RUBBED BRONZE BS = BLDG STANDARD CL = CLEAR (E) = EXISTING FH = FULL HEIGHT FR = FIRE RATED HC = HOLLOW CORE HM =HOLLOW METAL INT = BY INTERIOR DOCUMENTS NR =NON FIRE RATED PG =PAINT GRADE PT = PAINT SC = SOLID CORE SS = STAINLESS STEEL ST = STAIN WD = WOOD SHEET NOTES LEGEND © Gensler Date Description Project Name Project Number Description Scale Seal / Signature 2022 Tel 949.863.9434 Fax 949-553-1676 4675 MacArthur Court Suite 100 Newport Beach, CA 92600 USA 1/4" = 1'-0" 9/23/2024 2:47:22 PM BIM 360://007.3757.000 - Caribou Industries - 3rd & Broadway/3RD-B_INTERIOR_WEST_R20.rvt R2.I0.031 DOOR TYPES & SCHEDULE 07.3897.000 3rd & Broadway Interior 301 N. Broadway, Santa Ana, CA 06.13.2022 ISSUE FOR PLAN CHECK A 08.10.2022 REISSUE FOR PLAN CHECK C 06.17.2024 REVISION TO PERMIT D 09.27.2024 REISSUE FOR PLAN CHECK SCALE:1/4" = 1'-0" DOOR TYPES SCALE:1/4" = 1'-0" DOOR NOTES G3.4 - - 3' - 6" 8' - 0" 0' - 0 1/2" GL GL - - NON-RATED PIVOT HINGE WITH HOLD OPEN A1.3 3' - 4" 7' - 2" 3' - 0" 8' - 0" 0' - 1 3/4" HM PT HM PT NON-RATED STORAGE LOCKSET A1.2 3' - 4" 7' - 2" 3' - 0" 8' - 0" 0' - 1 3/4" HM PT HM PT NON-RATED PRIVACY LOCKSET U 4.2 - - 1' - 2" 7' - 0" 0' - 1 3/4" WD PT - - NON-RATED BI-FOLDING DOOR PULL U 3.2 - - 1' - 8" 7' - 0" 0' - 1 3/4" WD PT - - NON-RATED BI-FOLDING DOOR PULL U 2.2 3' - 2" 7' - 2" 2' - 10" 7' - 0" 0' - 1 3/4" WD PT HM PT NON-RATED PASSAGE LATCH U 2.1 3' - 2" 7' - 2" 2' - 10" 7' - 0" 0' - 1 3/4" WD PT HM PT NON-RATED PRIVACY LOCKSET WIDTH HEIGHT WIDTH HEIGHT THICK MATERIAL FINISH MATERIAL FINISH DIMENSIONS DIMENSIONS DIMENSIONS DIMENSIONS DIMENSIONSTYPE FRAME FRAME DOOR DOOR PANEL DOOR PANEL DOOR FRAME FIRE RATING HARDWARE SET DOOR SCHEDULE D 11/12/2024