Laserfiche WebLink
Page 1 of 18 <br />DIVISION: 03 00 00— <br />CONCRETE <br />Section: 03 16 00— <br />Concrete Anchors <br />DIVISION: 05 00 00— <br />METALS <br />Section: 05 05 19—Post- <br />Installed Concrete <br />Anchors <br />REPORT HOLDER: <br />ITW RED HEAD <br />ADDITIONAL LISTEE: <br />ITW BRANDS <br />EVALUATION SUBJECT: <br />TAPCON+ SCREW <br />ANCHORS AND <br />SAMMYS THREADED <br />ROD ANCHORS FOR <br />USE IN CRACKED AND <br />UNCRACKED <br />CONCRETE <br />1.0 EVALUATION SCOPE <br />Compliance with the following codes: <br />◼2021, 2018, 2015, and 2012 International Building Code® (IBC) <br />◼2021, 2018, 2015, and 2012 International Residential Code® (IRC) <br />For evaluation for compliance with codes adopted by Los Angeles Department of Building and Safety (LADBS), <br />see ESR-3699 LABC and LARC Supplement. <br />Property evaluated: <br />◼Structural <br />2.0 USES <br />The 1/4-inch-, 3/8-inch-, and 1/2-inch-diameter (6.4 mm, 9.5 mm, and 12.7 mm) Tapcon+ Screw Anchors with <br />Advanced Threadform Technology are used as anchorage in cracked and uncracked normalweight and <br />lightweight concrete having a specified compressive strength f′c = 2,500 psi to 8,500 psi <br />(17.2 MPa to 58.6 MPa) to resist static, wind, and seismic tension and shear loads. <br />The 1/2-inch-diameter (12.7 mm) Tapcon+ Screw Anchors with Advanced Threadform Technology are also <br />used as anchorage when installed in the soffit of cracked and uncracked normalweight and sand-lightweight <br />concrete over steel deck having a minimum specified compressive strength f′c = 3,000 psi (20.7 MPa) to resist <br />static, wind, and seismic tension and shear loads . <br />The 1/4-inch-diameter (6.4 mm) SAMMYS Anchors for use with threaded rods are available in two head styles: <br />the SAMMYS vertical threaded rod anchor, CCST 516; and SAMMYS horizontal threaded rod anchor, SW- <br />CCST 516. The CCST 516 anchor is used as anchorage in cracked and uncracked normalweight and sand- <br />lightweight concrete having a specified compressive strength f′c = 2,500 psi to 8,500 psi <br />(17.2 MPa to 58.6 MPa) to resist static and wind, tension or shear loads, and seismic tension loads only. The <br />SW-CCST 516 anchor is used as anchorage in uncracked normalweight and sand-lightweight concrete having <br />a specified compressive strength f′c = 2,500 psi to 8,500 psi (17.2 MPa to 58.6 MPa) to resist static and wind <br />shear loads only. <br />ICC-ES Evaluation Report <br />ESR-3699 <br />Reissued March 2024 This report also contains: <br />-LABC Supplement <br />-CBC Supplement <br />-FBC Supplement <br />Subject to renewal March 2026 <br />ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an <br />endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or <br />other matter in this report, or as to any product covered by the report. <br />Copyright © 2024 ICC Evaluation Service, LLC. All rights reserved.