Laserfiche WebLink
CITY OF SANTA ANA <br />Planning and Building Agency <br />ESR-4266 I Most Widely Accepted and Trusted <br />f <br />6of16 <br />TABLE 1—SETTING INFORMATION r%rF1 %J V <br />Nominal anchor diameter (in )-FOR -PE RR I'Vi -T- ISSUANCE <br />lofting information <br />Sym. <br />Units <br />1/4 <br />3/e <br />1/2 <br />51s <br />s/a <br />1 <br />ominal bit diameter <br />do <br />In. <br />1/4 <br />3/8 <br />1/2 <br />5/8 <br />34 <br />1 <br />Effective min. <br />In. <br />1-1/2 <br />1-1/2 <br />2 <br />2-1/2 <br />1-112' <br />2 <br />2-1/2 <br />3-1/4 <br />2-3/4 <br />3-1/4 <br />4 <br />3-1/4 <br />3tj3/4 <br />4 <br />5-3/4 I <br />embedment <br />bar <br />(mm) <br />(38) <br />(38) <br />(51) <br />(64) <br />(38) <br />(51) <br />(64) <br />(83) <br />(70) <br />(83) <br />(102) <br />(83) <br />(95) <br />(121) <br />(102) <br />(146)j <br />Nominal <br />in. <br />1-3/4 <br />1-7/8 <br />2-1/2 <br />3 <br />2" <br />2-1/2 <br />3 <br />3-3/4 <br />3-1/4 <br />3-3/4 <br />4-1/2 <br />4 <br />4-1/2 <br />5-1/2 <br />4-5/8 <br />6-3/8 <br />embedment <br />boom <br />mm <br />44) <br />(48) <br />(64) <br />(76) <br />(51) <br />(64) <br />(76) <br />(95) <br />(83) <br />(95) <br />(114) <br />(102 <br />114 <br />140 <br />117 <br />162 <br />In. <br />2 <br />2 <br />2-3/4 <br />3-1/4 <br />2-1/4' <br />2-3/4 <br />3-1/4 <br />4-1/4 <br />3-3/4 <br />4-1/4 <br />4-3/4 <br />4-1/4 <br />4-3/4 <br />5-3/4 <br />5 <br />6-3/4, <br />Min. hole depth <br />ho <br />mm <br />51) <br />(51) <br />1 (70) 1 <br />(83) <br />(57) <br />(70) <br />1 (83) <br />(108) <br />(95) <br />(108)1(121 <br />108 <br />121 <br />146 <br />127 <br />171 <br />Installation <br />ft-lb <br />4 <br />30 <br />50 <br />40 <br />110 <br />185 <br />Cque <br />TfhSr <br />Carbon steel' <br />(Nm) <br />(5) <br />(41) <br />(68) <br />(54) <br />(149) <br />(251) <br />Installation <br />ft-lb <br />6 <br />30 <br />40 <br />60 <br />125 <br />185 <br />torque <br />Tinsr <br />Stainless steel' <br />(Nm) <br />(8) <br />(41) <br />(54) <br />(81) <br />(169) <br />(251) <br />In. <br />5/16 <br />7116 <br />9/16 <br />11/16 <br />13116 <br />1-1/8 <br />Fixture hole diameter <br />dh <br />(mm) <br />(7.9) <br />(11.1) <br />(14.3) <br />(17.5) <br />(20.6) <br />(28.6) <br />Desian information for haf= <br />1-1/2 is only applicable <br />to carbon steel (CS) <br />KB-TZ2 <br />bolts. <br />collar UNC thread I <br />mandrel WIMMEM I dog point <br />expansion element bolt <br />washer L hex nut <br />FIGURE 1—HILTI CARBON STEEL KWIK BOLT TZ (KB-TZ2) <br />hnom <br />do <br />(lta��urainur u�l �l <br />• <br />FIGURE 2—HILTI KB-TZ2 INSTALLED <br />TABLE 2—LENGTH IDENTIFICATION SYSTEM (CARBON STEEL AND STAINLESS STEEL ANCHORS) <br />Length ID marking <br />A <br />B <br />C <br />D <br />E' <br />F <br />G <br />H <br />I <br />JN17 <br />M <br />N <br />O <br />P <br />Q <br />R <br />S <br />T <br />U <br />V <br />W <br />n bolt head <br />Length of <br />rom <br />1'/z <br />2 <br />2'/z <br />3 <br />3t'/.44"/z <br />5 <br />5'/z <br />6 <br />7Yz <br />8 <br />8'/= <br />9 <br />9'/z <br />10 <br />11 <br />12 <br />13 <br />14 <br />15 <br />nchor,p <br />to but <br />(inches) <br />of <br />2 <br />2'/z <br />3 <br />3'% <br />5 <br />5'/z <br />6 <br />6'/z <br />8 <br />8'/z <br />9 <br />9'/z <br />10 <br />11 <br />12 <br />13 <br />14 <br />15 <br />16 <br />ncluding <br />For SI: 1 inch = 25.4 mm. <br />13/8 diameter anchors with length of 3% are identified with an ohm (II) ID marking on the bolt head. <br />Carbon Steel Stainless Steel 304 Stainless Steel 316 <br />Single Notch Double Notch - Triple Notch <br />Length Length ' - Length <br />J Identification Identification w Identification <br />Code Code <br />Code vty +fw� <br />FIGURE 3—BOLT HEAD WITH LENGTH IDENTIFICATION CODE AND KB-TZ2 HEAD NOTCH EMBOSSMENT <br />