|
CITY OF SANTA ANA
<br />Planning aqd-Mild-ink-Agency
<br />FIRE NOTE
<br />1. FIRE SPREAD AND SMOKE -DEVELOPED INDICES FOR WALL AND
<br />CEILING FINISHES SHALL BE IN ACCORDANCE WITH SECTIONS
<br />R302.9.1 AND R302.9.4
<br />WATER HEATER /ELECTRICAL READY
<br />1.AT TANKLESS WATER HEATER -PROVIDE A DEDICATED 125 VOLT,
<br />20 AMP ELECTRICAL PANEL WITH A 120/ 240 VOLT 3 CONDUCTOR
<br />10 AWG COPPER BRANCH CIRCUIT, WITHIN 3 FEET OF THE WATER
<br />HEATER AND ACCESSIBLE TO THE WATER HEATER. (CENERGYC)
<br />150.0(N)(1)(A)
<br />2. WATER HEATING SYSTEMS (ESS) READY. ALL SINGLE-FAMILY
<br />RESIDENCES THAT INCLUDE ONE OR TWO DWELLING UNITS SHALL
<br />MEET THE FOLLOWING. ALL ELECTRICAL COMPONENTS SHALL BE
<br />INSTALLED IN ACCORDANCE WITH THE CALIFORNIA ELECTRICAL
<br />CODE: (CENERGYC150.0(S)
<br />AT LEAST ONE OF THE FOLLOWING SHALL BE PROVIDED:
<br />A. ESS READY INTERCONNECTION EQUIPMENT WITH A MINIMUM
<br />BACKED -UP CAPACITY OF 60 AMPS AND A MINIMUM OF FOUR
<br />ESS-SUPPLED BRANCH CIRCUITS, OR
<br />B. A DEDICATED RACEWAY FROM THE MAIN SERVICE PANELBOARD
<br />(SUBPANEL) THAT SUPLIES THE BRANCH CIRCUITS IN SECTION
<br />150.0 (S)(2). ALL BRANCH CIRCUITS ARE PERMITTED TO BE
<br />SUPPLIED BY THE MAIN SERVICE PANEL PRIOR TO THE
<br />INSTALLATION OF AN ESS. THE TRADE SIZE OF THE RACEWAY
<br />SHALL BE NOT LESS THAN 1 INCH . THE PANELBOARD THAT
<br />SUPPLIES THE BRANCH CIRCUITS(SUBPANEL) MUST BE LABELED "
<br />SUBPANEL SHALL INCLUDE ALL BACKED UP LOAD CIRCUITS."
<br />3. A MINIMUM OF FOUR BRANCH CIRCUITS SHALL BE IDENTIFIED
<br />AND HAVE THEIR SOURCE OF SUPPLY COLLOCATED AT A SINGLE
<br />PANELBOARD SUITABLE TO BE SUPPLIED BY THE ESS. AT LEAST
<br />ONE CIRCUIT SHALL SUPPLY THE REFRIGERATOR, ONE LIGHTING
<br />CIRCUIT SHALL BE LOCATED NEAR THE PRIMARY EGRESS AND AT
<br />LEAST ONE CIRCUIT SHALL SUPPLY A SLEEPING ROOM
<br />RECEPTACLE OUTLET.
<br />4. THE MAIN PANELBOARD SHALL HAVE A MINIMUM BUSBAR RATING
<br />OF 225 AMPS.
<br />5. SUFFICIENT SPACE SHALL BE RESERVED TO ALLOW FUTURE
<br />INSTALLATION OF A SYSTEM ISOLATION EQUIPMENT/TRANSFER
<br />SWITCH WITHIN 3 FEET OF THE MAIN PANELBOARD. RACEWAYS
<br />SHALL BE INSTALLED BETWEEN THE PANELBOARD AND THE
<br />SYSTEM ISOLATION EQUIPMENT/TRANSFER SWITCHED LOCATION TO
<br />ALLOW THE CONNECTION OF BACK UP POWER SOURCE.
<br />ELECTRICAL COOKTOP DRYER READY
<br />6. ELECTRIC COOKTOP READY.SYSTEMS USING GAS OR PROPANE
<br />COOKTOP TO SERVE INDIVIDUAL DWELLING UNITS SHALL INCLUDE
<br />THE FOLLOWING: (CENERGY C 150.0(U)
<br />A. A DEDICATED 240 VOLT BRANCH CIRCUIT WIRING SHALL BE
<br />INSTALLED WITHIN 3 FEET FROM THE COOKTOP AND ACCESSIBLE TO
<br />THE COOKTOP WITH NO OBSTRUCTIONS. THE BRANCH CIRCUIT
<br />CONDUCTORS SHALL BE RATED AT 50 AMPS MINIMUM THE
<br />BLANK COVER SHALL BE IDENTIFIED AS "240V READY." ALL
<br />ELECTRICAL COMPONENTS SHALL BE INSTALLED IN ACCORDANCE
<br />WITH THE CALIFORNIA ELECTRICAL CODE.
<br />B. THE MAIN ELECTRICAL SERVICE PANEL SHALL HAVE A RESERVED
<br />SPACE TO ALLOW FOR THE INSTALLATION OF A DOUBLE POLE
<br />CIRCUIT BREAKER FOR A FUTURE ELECTRIC CLOTHES DRYER
<br />INSTALLATION. THE RESERVED SPACE SHALL BE PERMANENTLY
<br />MARKED AS "FOR FUTURE 240V USE."
<br />ELECTRICAL CLOTHE DRYER READY
<br />ELECTRIC CLOTHES DRYER READY. CLOTHES DRYER LOCATIONS WITH
<br />GAS OR PROPANE PLUMBING TO SERVE INDIVIDUAL DWELLING UNITS
<br />SHALL INCLUDE THE FOLLOWING: (CENERGYC150.0(V)
<br />1. A DEDICATED 240 VOLT BRANCH CIRCUIT WIRING SHALL BE
<br />INSTALLED WITHIN 3 FEET FROM THE CLOTHES DRYER LOCATION
<br />AND ACCESSIBLE TO THE CLOTHES DRYER LOCATION WITH NO
<br />OBSTRUCTIONS. THE BRANCH CIRCUIT CONDUCTORS SHALL BE
<br />RATED AT 30 AMPS MINIMUM. THE BLANK COVER SHALL BE
<br />IDENTIFIED AS "240V READY." ALL ELECTRICAL COMPONENTS SHALL
<br />BE INSTALLED IN ACCORDANCE WITH THE CALIFORNIA ELECTRICAL
<br />CODE.
<br />2. THE MAIN ELECTRICAL SERVICE PANEL SHALL HAVE A RESERVED
<br />SPACE SHALL BE PERMANENTLY MARKED AS "FOR FUTURE 240V
<br />USE.
<br />ELECTRICAL
<br />1. IN BATHROOMS AND LAUNDRY ROOMS, NAT LEAST ONE
<br />LUMINAIRE IN EACH OF THESE SPACES MUST BE CONTOLLED BY
<br />AN OCCUPANT SENSOR OR A VACANCY SENSOR PROVIDING
<br />AUTOMATIC -OFF FUNCTIONALLY. IF AN OCCUPANT SENSOR IS
<br />INSTALLED, IT MUST BE INITIALLY CONFIGURED TO MANUAL -ON
<br />OPERATON USING THE MANUAL CONTROL REQUIRED UNDER SECTION
<br />150.0(K)21.
<br />2. SERVICES DISCONNECTING MEANS SHALL BE INSTALLED OUTSIDE THE
<br />BUILDING OR INSIDE NEARAST THE POINT OF ENTRANCE OR SERVICE
<br />CONDUCTORS. (CEC 230.70)
<br />3. NEWLY CONSTRUCTED ONE AND TWO FAMILY DWELLINGS AND
<br />TOWNHOUSES WITH ATTACHED PRIVATE GARAGES SHALL COMPLY WITH
<br />THE EV CHARGING INFRASTRUCTURE REQUIREMENTS IN CGBC 4.106 AND
<br />CRC R309.8
<br />LIGHTING MEASURES
<br />1. LIGHTING IN BATHROOMS, GARAGES, AND LAUNDRY ROOMS,WALK IN
<br />CLOSETS AND UTILITY ROOMS. ALL LUMINAIRES SHALL BE HIGH
<br />EFFICACY AND SHALL BE CONTROLLED BY AN OCCUPANCY OR VACANCY
<br />SENSOR.
<br />2. HABITABLE SPACES. ALL LUMINAIRES SHALL BE HIGH EFFICACY AND
<br />SHALLN BE CONTROLLED BY A VACANCY/OCCUPANCY SENSOR OR
<br />DIMMER.
<br />3. OUTDOOR LIGHTING. ALL LUMINAIRES MOUNTED TO THE BUILDING ON
<br />THE SAME LOT SHALL BE HIGH EFFICACY LUMINAIRES AND SHALL BE
<br />CONTROLLED BY A PHOTOCONTROL/MOTION SENSOR COMBINATION (WITH
<br />OVERRIDE). SEE 150(k) 3 FOR REQUIREMENTS.
<br />4. KITCHEN ALL INSTALLED WATTAGE IN KITCHEN SHALL BE HI
<br />EFFICACY.
<br />GLAZING
<br />1. GLAZING IN THE FOLLOWING LOCATIONS SHALL BE SAFETY
<br />GLAZING CONFORMING TO THE HUMAN IMPACT LOADS OF SECTION
<br />R308.3 .
<br />A. FIXED AND OPERABLE PANELS OF SWINGING, SLIDING AND
<br />BI-FOLD DOOR ASSEMBLIES.
<br />B. GLAZING IN AN INDIVIDUAL FIXED OR OPERABLE PANEL
<br />ADJACENT TO A DOOR WHERE THE NEAREST VERTICAL EDGE IS
<br />WITHIN A 24 INCH ARC OF EITHER VERTICAL EDGE OF THE DOOR IN
<br />A CLOSED POSITION AND WHOSE BOTTOM EDGE IS LESS THAN 60
<br />INCHES ABOVE THE FLOOR OR WALKING SURFACE.
<br />C. GLAZING IN AN INDIVIDUAL FIXED OR OPERABLE PANEL THAT
<br />MEETS ALL OF THE FOLLOWING CONDITIONS:
<br />GLAZING
<br />1. EXPOSED AREA OF AN INDIVIDUAL PANEL GREATER THAN 9
<br />SQUARE FEET.
<br />2. BOTTOM EDGE LESS THAN 18 INCHES ABOVE THE FLOOR .
<br />3. TOP EDGE GREATER THAN 36 INCHES ABOVE THE FLOOR.
<br />4. ONE OF MORE WALKING SURFACES WITHIN 36 INCHES
<br />HORIZONTALLY OF THE GLAZING.
<br />D. GLAZING IN RAILINGS.
<br />E. GLAZING IN ENCLOSURES FOR OR WALLS FACING HOT TUBS,
<br />WHIRLPOOLS, SAUNAS, STEAM ROOMS, BATHTUBS AND SHOWERS
<br />WHERE THE BOTTOM EDGE OF THE GLAZING IS LESS THAN 60
<br />INCHES MEASURED VERTICALLY ABOVE ANY STANDING OR WALKING
<br />SURFACE.
<br />AGING -IN- P LACE/FALL
<br />1. REINFORCEMENT FOR GRAB BARS. (R327.1.1) AT LEAST ONE
<br />BATHROOM ON THE ENTRY LEVEL SHALL BE PROVIDED WITH
<br />REINFORCEMENT INSTALLED IN ACCORDANCE WITH THIS SECTION. WHERE
<br />THERE IS NO BATHROOM ON THE ENTRY LEVEL, AT LEAST ONE
<br />BATHROOM ON THE 2ND OR 3RD FLOOR OF THE DWELLING SHALL
<br />COMPLY WITH THIS SECTION.
<br />A. REINFORCEMENT SHALL BE SOLID LUMBER OR OTHER CONSTRUCTION
<br />MATERIALS APPROVED BY THE ENFORCING AGENCY.
<br />B. REINFORCEMENT SHALL NOT BE LESS THAN 2 BY 8 INCH NOMINAL
<br />LUMBER (1-1/2" X 7-1/4" ACTUAL DIMENSION) OR OTHER
<br />CONSTRUCTION MATERIAL PROVIDING EQUAL HEIGHT AND LOAD
<br />CAPACITY. REINFORCEMENT SHALL BE LOCATED BETWEEN 32" AND
<br />39-1 /4" ABOVE THE FINISHED FLOOR, FLUSH WITH THE WALL FRAMING.
<br />C. WATER CLOSET REINFORCEMENT SHALL BE INSTALLED ON BOTH SIDE
<br />WALLS OF THE FIXTURE, OR ONE SIDE WALL AND THE BACK WALL.
<br />D. SHOWER REINFORCEMENT SHALL BE CONTINUOUS WHERE WALL
<br />FRAMING IS PROVIDED.
<br />E. BATHTUB AND COMBINATION BATHTUB/SHOWER REINFORCEMENT
<br />SHALL BE CONTINUOUS ON EACH END OF THE BATHTUB AND THE
<br />BACK WALL. ADDITIONALLY, BACK WALL REINFORCEMENT FOR A LOWER
<br />GRAB BAR SHALL BE PROVIDED WITH THE BOTTOM EDGE LOCATED NO
<br />MORE THAN 6" ABOVE THE BATHTUB RIM.
<br />F. WHERE THE WATER CLOSET IS NOT PLACED ADJACENT TO A SIDE
<br />WALL CAPABLE OF ACCOMMODATING A GRAB BAR, THE BATHROOM
<br />SHALL HAVE PROVISIONS FOR INSTALLATION OF FLOOR MOUNTED,
<br />FOLDAWAY OR SIMILAR ALTERNATE GRAB BAR REINFORCEMENTS
<br />APPROVED BY THE ENFORCING AGENCY.
<br />1. DOCUMENTATION FOR GRAB BAR REINFORCEMENT. (R327.1.1.1)
<br />INFORMATION AND /OR DRAWINGS IDENTIFYING THE LOCATION OF GRAB
<br />BAR REINFORCEMENT SHALL BE PLACED IN THE OPERATION AND
<br />MAINTENANCE MANUAL IN ACCORDANCE WITH THE CALIFORNIA GREEN
<br />BUILDING STANDARDS CODE. CH 4, DIVISION 4.4.
<br />2. ELECTRICAL RECEPTACLE OUTLET, SWITCH AND CONTROL HEIGHTS.
<br />(R327.1.2.) ELECTRICAL RECEPTACLE OUTLETS, SWITCHES, AND
<br />CONTROLS (INCLUDING CONTROLS FOR HEATING, VENTILATION AND AIR
<br />CONDITIONING ) INTENDED TO BE USED BY OCCUPANTS SHALL BE
<br />LOCATED NO MORE THAN 48" MEASURED FROM THE TOP OF THE
<br />OUTLET BOX AND NOT LESS THAN 15" MEASURED FROM THE BOTTOM
<br />OF THE OUTLET BOX ABOVE THE FINISHED FLOOR.
<br />3. INTERIOR DOORS. (R327.1.3) EFFECTIVE JULY 1.2024 AT LEAST
<br />ONE BATHROOM AND ONE BEDROOM ON THE ENTRY LEVEL SHALL
<br />PROVIDE A DOORWAY WITH A NET CLEAR OPENING OF NOT LESS THAN
<br />32", MEASURED WITH THE DOOR POSITIONED AT AN ANGLE OF 90
<br />DEGREES FROM THE CLOSED POSITION; OR, IN THE CASE OF A 2- OR
<br />3- STORY SINGLE FAMILY DWELLING, ON THE 2ND OR 3RD FLOOR OF
<br />THE DWELLING IF A BATHROOM OR BEDROOM IS NOT LOCATED ON THE
<br />ENTRY LEVEL.
<br />4. DOORBELL BUTTONS. (R327.1.4) DOORBELL BUTTONS OR CONTROLS,
<br />WHEN INSTALLED, SHALL NOT EXCEED 48" MEASURED FROM THE
<br />EXTERIOR FLOOR OR LANDING, A STANDARD DOORBELL BUTTON OR
<br />CONTROL SHALL ALSO BE PROVIDED AT A HEIGHT NOT EXCEEDING 48"
<br />ABOVE EXTERIOR FLOOR OR LANDING, MEASURED FROM THE TOP OF
<br />THE DOORBELL BUTTON OR CONTROL.
<br />NOTES:
<br />1. BATHTUB AND SHOWER FLOORS, AND WALLS ABOVE BATHTUBS WITH A
<br />SHOWERHEAD, AND SHOWER COMPARTMENTS SHALL BE FINISHED WITH A
<br />NONABSORBENT SURFACE EXTENDING TO A HEIGHT OF NOT LESS THAN 6
<br />FEET ABOVE THE FLOOR.
<br />2. SHOWER DOORS SHALL SWING OUT. NET AREA OF SHOWER RECEPTOR
<br />SHALL BE NOT LESS THAN 1,024 SQ . IN. OF FLOOR AREA, AND ENCOMPASS
<br />30 IN. DIAMETER CIRCLE.
<br />3. ALL HOSE BIBBS MUST BE PROTECTED BY AN ANTI -SIPHON DEVICE
<br />4. TAMPER -RESISTANT RECEPTACLES SHALL BE INSTALLED IN ALL AREAS
<br />SPECIFIED IN 210.52 ALL NONLOCKING-TYPE 12 VOLT, 15- AND 20 AMPERE
<br />RECEPTACLES SHALL BE LISTED TAMPER -RESISTANT RECEPTACLES.
<br />5. ALL SHOWERS AND TUB -SHOWERS SHALL HAVE A PRESSURE BALANCE,
<br />THERMOSTATIC MIXING VALVE, OR A COMBINATION PRESSURE
<br />BALANCE/THERMOSTATIC MIXING TYPE VALVE.
<br />6. ALL NEW, REPLACEMENT AND EXISTING WATER HEATERS SHALL BE STRAPPED
<br />TO THE WALL IN TWO PLACES. ONE IN THE UPPER 1/3 OF THE TANK AND ONE IN
<br />THE LOWER 1/3 OF THE TANK. THE LOWER POINT SHALL BE A MINIMUM OF 4-IN.
<br />ABOVE THE CONTROLS.
<br />7. ALL FINISHED MATERIALS, SUCH AS ADHESIVES, SEALANTS, CAULKS, PAINTS,
<br />AEROSOL PAINTS , COATINGS, CARPET SYSTEMS, RESILIENT FLOORING SYSTEMS
<br />AND COMPOSITE WOOD PRODUCTS SHALL CONFORM TO THE VOC AND
<br />FORMALDEHYDE LIMITS SET SET FORTH IS SECTION 4.504.2, 4.504.4. 4.504.5
<br />AND TABLES 4.504.1, 4.504.2, 4.504.3 AND 4.504.5 2019 CGB SC
<br />8. SHOWER OR TUB EQUIPPED WITH A SHOWERHEAD SHALL HAVE A MINIMUM
<br />CELING HEIGTH OF 6-8" ABOVE A MINIMUM AREA OF 30"X30" AT THE SHOWER
<br />HEAD
<br />9. WATER HEATERS SHALL HAVE A TEMPERATURE AND PRESSURE RELIEF VALVE
<br />COMPLYING WITH CPC SECTIONS 505.4 & 608.6. THE POINT OF DISCHARGE FOR
<br />RELIEF VALVE SHALL BE IN ACCORDANCE WITH CPC SECTION 608.7
<br />10. THE SEWER LINE FOR THE APPROVED ADU MUST CONNECT TO THE MAIN
<br />LATERAL SEWER LINE PRIOR TO THE CONNECTION OF THE MAIN RESIDENCE.
<br />11. EACH BATHROOM CONTAINING A BATHTUB, SHOWER OR TUB/SHOWER
<br />COMBINATION SHALL BE MECHANICALLY VENTILATED FOR PURPOSES OF HUMIDITY
<br />CONTROL IN ACCORDANCE WITH CMC, CHAPTER 4 AND CGBSC, CHAPTER 4,
<br />DIVISION 4.5. (R303.3.1. CRC)
<br />12. BATHROOMS, WATER CLOSET COMPARTMENTS AND OTHER SIMILAR ROOMS
<br />SHALL BE PROVIDED WITH GLAZED AREA IN WINDOWS OF NOT LESS THAN 3 SQ, FT,
<br />ONE HALF SHALL BE OPENABLE .(R303.3 CRC)
<br />EXCEPTION: GLAZED AREA SHALL NOT BE REQUIRED WHERE ARTIFICIAL LIGHT
<br />AND MECHANICAL VENTILATION ARE PROVIDED. MINIMUM VENTILATION RATES
<br />SHALL BE 50 CFM FOR INTERMITENT VENTILATION AND 25 CFM OF CONTINOUS
<br />VENTILATION AND VENTED DIRECTLY TO THE OUTSIDE.
<br />CALIFORNIA MECHANICAL CODE:
<br />1. 120 -VOLT RECEPTACLE COMPLYING WITH CMC SECTION 309 SHALL
<br />BE LOCATED WITH 25' OF THE EQUIPMENT FOR SERVICE AND
<br />MAINTAINANCE PURPOSES.
<br />2. AN APPROVED INDEPENDENT ELECTRICAL DISCONNECT COMPLYING
<br />IWTH CMC SECTION 309 IS REQUIRED FOR EACH PIECE OF EQUIPMENT
<br />WITHIN SIGHT OF THE EQUIPMENT, WHEN SUPPLY VOLTAGE IS GREATER
<br />THAN 50 VOLTS.
<br />3. CONDENSATE LINES FROM MECHANICAL EQUIPMENT SHALL
<br />DISCHARGE TO A PLUMBING FIXTURE OR STORM DRAINAGE BY MEANS
<br />OF AN INDIRECT WASTE PIPE. CONSENSATE LINES SHALL NOT
<br />TERMINATE IN A LANDSCAPE OR YARD AREAS.
<br />4. WHEN APPROVED, THE ENGINEER OF RECORD, ARCHITECT OR PLANS
<br />PREPARER SHALL PROVIDE MANUFACTURE'S DETAILS AND
<br />SPECIFICATIONS FOR VENTING OF TANKLESS WATER HEATERS.
<br />5. A DRYER COMPARTMENT/CLOSET SHALL BE PROVIDED WITH A
<br />MINIMUM OPENING OF 100 SQ INCHES FOR MAKE UP AIR IN THE DOOR
<br />OR BY OTHER APPROVED MEANS IN ACCORDANCE WITH CMC SECTION
<br />504.3.1.
<br />6. A DOMESTIC CLOTHE DRYER DUCT SHALL BE OF METAL AND A
<br />MINIMUM OF 4" DIAMETER. THE EXHAUST DUCT SHALL NOT EXCEED A
<br />TOTAL COMBINED HORIZONTAL AND VERTICAL LENGTH OF 14',
<br />INCLUDING TWO 90-DEGREE ELBOWS. TWO FEET SHALL BE DEDUCTED
<br />FOR EACH 90-DEGREE ELBOW IN EXCESS OF TWO. THE DRYER SHALL
<br />BE VENTED TO THE OUTSIDE AIR. CMC SECTIONS 504.3.1.
<br />1. EXHAUST FANS SHALL BE SWITCHED SEPARATELY FROM THE LIGHTING
<br />SYSTEMS SECTION 150.0 (K) (2) (B).
<br />2. EXHAUST FANS FOR BATHROOM AND LAUNDRY ROOM 50 CFM
<br />3. EXHAUST DUCTS SHALL TERMINATE OUTSIDE THE BUILDING AND SHALL BE
<br />EQUIPPED WITH BACK DRAFT DAMPERS OR WITH MOTORIZED DAMPERS THAT
<br />AUTOMATICALLY SHUT WHERE THE SYSTEM OR SPACES SERVED ARE NOT IN
<br />USE. CMC.504.1.1
<br />4. EXHAUST OPENINGS TERMINATING TO THE OUTDOORS SHALL BE COVERED
<br />WITH A CORROSION RESISTANT SCREEN HAVING NOT LESS THAN 4" OF AN INCH
<br />OPENING AND SHALL HAVE NOT MORE THAN 2" INCH OPENING AND SHALL HAVE
<br />NOT MORE THAN 2" INCH OF AN OPENINGS. CMC 502.1.
<br />CALIFORNIA RESIDENTIAL CODE
<br />1. WALL AND CEILING SHALL NOT EXCEED THE FLAME -SPREAD
<br />CLASSIFICATIONS IN CRC SECTKION R302.9
<br />2. INTERIOR WALL COVERING SHALL COMPLY WITH THE
<br />REQUIREMENTS CITED IN CRC SECTION 702 AND TABLE R702.3.5
<br />FOR THE APPROVED MATERIALS (FASTENERS, FASTENER SPACING
<br />COATING THICKNESS, NUMBER OF COATS, ETC.
<br />3. CEMENT, FIBER -CEMENT, FIBER MAT REINFORCED CEMENT,
<br />GLASS MAT GYPSUM OR FIBER -REINFORCED GYPSUM BACKERS
<br />SHALL BE USED AS A BASE FOR WALL TILE IN TUB AND SHOWER
<br />AREAS AND CEILING PANELS IN SHOWER AREAS IN ACCORDANCE
<br />WITH CRC SECTION R702.4.2 CRC.
<br />4. FASTENERS FOR ROOF COVERING SHALL BE CORROSION
<br />RESISTAN SUCH AS COPPER, BRASS, STAINLESS STEEL OR
<br />GALVANIZED. (CRC) TABLES R602.3(10) AND R502.3(2)
<br />5. EACH PANE OF SAFETY GLAZING INSTALLED IN HAZARDOUS
<br />LOCATIONS SHALL BE IDENTIFIED (ACID ETCHED, SAND BLASTED,
<br />CERAMIC FIRED, ETC) BY A MANUFACTURE'S DESIGNATION, THE
<br />MANUFACTURER OR INSTALLER AND SAFETY GLAZING STANDARD
<br />WHICH IT COMPLIES.
<br />6. FIRE BLOCKING MUST BE PROVIDED IN ACCORDANCE WITH CRC
<br />SECTION R302.11 AT THE FOLLOWING LOCATIONS:
<br />A. IN CONCEALED SPACES OF STUD WALLS AND PARTITIONS,
<br />INCLUDING FURRED SPACES, AT THE CEILING AND FLOOR LEVELS
<br />B. IN CONCEALED SPACES OF STUD WALLS AND PARTITIONS,
<br />INCLUDING FURRED SPACES, AT 10-FOOT INTERVALS ALONG THE
<br />LENGTH OF THE WALL.
<br />C. AT ALL INTERCONNECTIONS BEWEEN CONCEALED VERTICAL AND
<br />HORIZONTAL SPACES SUCH AS OCCUR AT SOFFITS, DROP CEILINGS
<br />AND COVE CEILINGS.
<br />D. IN OPENINGS AROUND VENTS, PIPES, DUCTS, CHIMNEYS, FIRE
<br />PALCES AND SIMILAR OPENINGS WHICH AFFORD A PASSAGE FOR
<br />FIRE AT CEILING AND FLOOR LEVELS, WITH MATERIALS TESTED FOR
<br />THE FORM AND MANNER THEY ARE INTENDED.
<br />7. WHERE TOP OR SOLE PLATE ARE CUT FOR PIPES, A METAL TIE
<br />MINIMUM 0.058 INCHES THICK AND 1-1/2" WIDE SHALL BE FASTENED
<br />ACROSS THE OPENING WITH (6) 16D NAILS MINIMUM EACH SIDE.
<br />8. FIELD CUTTING ENDS, NOTCHES AND DRILLED HOLES IN
<br />PRESERVATIVE -TREATED WOOD SHALL BE TREATED IN THE FIELD IN
<br />ACCORDANCE WITH AWPA MA4.
<br />9. PROVIDE DOUBLE TOP PLATE WITH MINIMUM 48" LAP SPICES AND
<br />(8) 16 LAP SPLICE NAILING.
<br />10. BRACED WALL PANEL HOLD-DOWN HARDWARE SHOWN ON THE
<br />APPROVED PLANS OR IN ACCORDANCE WITH CRC SECTION R602.10
<br />MUST BE SECURED IN PLACE PRIOR TO FOUNDATION INSPECTION.
<br />CALIFORNIA ELECTRICAL CODE:
<br />1. IN EVERY DWELLING UNIT, FIXED APPLIANCES SUCH AS FOOD WASTED
<br />GRINDERS, DISHWASHER, WASHING MACHINES, DRYERS, LAUNDRY TRAY
<br />LOCATION, BUILT-IN REGRIGERATORS OR FREEZERS, FURANCES, AC UNITS,
<br />BUILT-IN HEATERS OR ANY OTHER FIXED APPLIANCE WITH A MOTOR OF 1/4"
<br />H.P. OR LARGER SHALL BE ON A SEPARATE 20 AMP. BRANCH CIRCUIT
<br />COMPLYING WITH CEC SECTION 422.10
<br />2. RECEPTACLES COMPLYING WITH CEC SECTION 210.52 SHALL BE LISTED AS
<br />TAMPER-RESITANT FOR ALL 15 AND 20 AMPERE RECEPTACLES IN DWELLING
<br />UNIT FAMILY, DINING, LIVING, PARLORS, LIBRARIES, DENS, BED ROOMS,
<br />SUNROOMS, RECREATION ROOMS, CLOSETS, HALLWAYS, OR SIMILAR ROOMS
<br />AND AREAS.
<br />3. THE ENGINEER OF RECORD, ARCHITECT OR PLANS PREPARER SHALL
<br />PROVIDE DETAILS TO THE CITY INSPECTOR, UPON REQUEST, SHOWING THE
<br />LOCATION AND SIZE OF THE MAIN SERVICE PANEL (MSP AND THE SOURCE
<br />OF POWER FOR THE APPROVED ADU.
<br />4. RECEPTACLES COMPLYING WITH CEC SECTION 210.52 SHALL BE LISTED AS
<br />TAMPER-RESITANT FOR ALL 15 AND 20 AMPERE RECEPTACLES IN DWELLING
<br />UNIT FAMILY, DINING, LIVING, PARLORS, LIBRARIES, DENS, BED ROOMS,
<br />SUNROOMS, RECREATION ROOMS, CLOSETS, HALLWAYS, OR SIMILAR ROOMS
<br />AND AREAS.
<br />5. A WORKLIGHT, SWITCH AND RECEPTACLE OUTLETS COMPLYING WITH CEC
<br />SECTION 210.70(3) IS REQUIRED FOR ATTICS, UNDER FLOOR SPACES, UTILITY
<br />ROOMS, AND BASEMENTS WHERE THESE SPACES ARE USED FOR STORAGE
<br />OR CONTAIN EQUIPEMENT REQUIRING SERVICING. THE LIGHTING OUTLET
<br />SHALL BE PROVIDED AT OR NEAR THE EQUIPMENT REQUIRING SERVICING.
<br />CALIFORNIA ENERGY CODE:
<br />1. RECESSED LIGHTS INTALLED IN AN INSULATED CEILING OR CAVITY ARE
<br />REQUIRED T HAVE A ZERO CLEARANCE INSULATION COVER (IC), BE ASTM
<br />E283 CERTIFIED THAT THEY ARE AIR TIGHT, AND SEALED WITH A GASKET
<br />OR CAULK BETWEEN THE HOUSE AND THE CEILING.
<br />2. OUTDOOR LIGHTING ATTACHED TO A BUILDING MUST BE HIGH EFFICACY,
<br />OR CONTROLLED BY A MOTION SENSOR WITH AN INTEGRAL
<br />PHOTO -CONTROL.
<br />3. ALL NEW GLAZING SHALL BE INSTALLED WITH LABELS TO REMAIN IN
<br />PLACE FOR INSPECTION.
<br />4. ROOMS CONTAINING BATHTUBS, SHOWERS, SPAS, AND SIMILAR
<br />BATHING FIXTURES SHALL BE MECHANICALLY VENTILATED. A MINIMUM
<br />RATE OF 50CFM IS REQUIRED. UPON REQUEST FROM THE CITY INSPECTOR,
<br />THE ENGINEER OF RECORD, ARCHITECT OR PLANS PREPARER SHALL
<br />PROVIDE DETAILS FOR DUCTING SIZE AND LENGTHS TO MEET THE
<br />MINIMUM REQUIREMENTS OF ASHRA STANDARD 62.2 AND MAXIMUM SOUND
<br />RATING OR 3 SONE FOR INTERMITTENT OPERATION.
<br />CALIFORNIA PLUMBING CODE:
<br />1. ALL HOSE BIBS MUST BE PROTECTED BY ANTI SIPHO DEVICE
<br />COMPLYING WITH CPC SEC TION 603.
<br />2. ANTI -SCALDING OR THRMOSTATIC MIXING VALVES ARE REQUIRED AT
<br />SHOWERS AND TUB/SHOWER COMBINATION. FOR PE
<br />3.WATER HEATERS SHALL HAVE A TEMPERATURE AND PRESSURE RELIEF
<br />VALVE COMPLYING WITH CPC SECTIONS 505.4 & 608.6. 1 HE POINT OF
<br />DISCHARGE FOR RELIEF VALVE SHALL BE IN ACCORDAN E WITH CPC
<br />SECTION 608.7.
<br />4. WHRESHALL HAVE A VEDDOED CAT DTANTANOUS GAS LINE SIZED ERGASTER THE AP LIP= &sI D
<br />SPECIFICATIONS.
<br />Date:
<br />5. WATER PIPING MATERIALS WITHIN A BUILDING SHALL E IN
<br />ACCORDANCE WITH SEC. 604.1 OF THE CALIFORNIA PLU BING CODE.
<br />PEX, CPVC AND OTHER PLASTIC WATER PIPING SYSTEM
<br />INSTALLED IN ACCORDANCE WITH THE REQUIREMENTS OF SEC. 604 OF
<br />THE CPC, INSTALLATION STANDARDS OF APPENDIX I OF THE CPC AND
<br />MANUFACTURERS RECOMMENDED INSTALLATION STANDARD. CPVC
<br />WATER PIPING REQUIRES A CERTIFICATION OF COMPLIANCE AS
<br />SPECIFIED IN SEC. 604.1.1(d) OF THE CPC PRIOR TO PERMIT ISSUANCE.
<br />6. WATER HEATER CLOSET SHALL HAVE 15 TO ANY WALL OR
<br />OBSTRUCTION ON EACH SIDE OF ITS CENTERLINE AND 24" CLEAR SAPCE
<br />IN FRONT. (CPC 402.5)
<br />7. PER SECTION 311.1 OF THE CALIFORNIA PLUMBING CODE, AN ADU
<br />BUILDING SEWER SHALL BE SEPARATELY CONNECTED TO THE PUBLIC
<br />SEWER, OR TRUNK SEWER (SEWER MAINTENANCE SADDLE PERMIT OR
<br />SANITATION DISTRICT APPROVAL IN ADDITION TO AN ENCROACHMENT
<br />PERMIT ARE REQUIRED.) HOWEVER, SINCE THE LOT MAY NOT BE
<br />SUBDIVIDED IN A MANNER THAT THE ADU BECOMES A SINGLE - FAMILY
<br />UNIT, THE BUILDING SEWER FROM THE ADU MAY CONNECT TO THE
<br />BUILDING SEWER FROM THE EXISTING BUILDING AT A POINT 2 FEET
<br />OUTSIDE OF THE EXISTING BUILDING.
<br />18. ALL GROUNDING ELECRODES AS DESCRIBED IN CED 250.529(A) (7)
<br />THAT ARE PRESENT AT EACH BUILDING OR STRUCTURE SERVED SHALL
<br />BE BONDED TOGETHER TO FORM THE GROUNDING ELECTRODE SYSTEM.
<br />IF MULTIPLE RODS, PIPE, OR PLATE ELECTRODES ARE INSTALLED TO
<br />MEET THE REQUIREMENTS OF CED 250.53 (A) (3) THEY SHALL NOT BE
<br />LESS THAN 6 FEET APART.
<br />EGRESS
<br />1.BASEMENTS, HABITABLE ATTICS AND EVERY SLEEPING ROOM
<br />SHALL HAVE AT LEAST ONE OPENABLE EMERGENCY ESCAPE AND
<br />RESCUE OPENING HAVING A MINIMUM NET CLEAR OPENING OF 5.7
<br />SQUARE FEET EXCEPT FOR GRADE FLOOR OPENINGS SHALL HAVE A
<br />MINIMUM NET CLEAR OPENING OF 5 SQUARE FEET. THE MIN. NET
<br />CLEAR OPENING HEIGHT SHALL BE 24 IN. WIDTH SHALL BE 20 IN.
<br />MIN. , AND BOTTOM OF THE CLEAR OPENING SHALL BE NO
<br />GREATER THAN 44 INCHES MEASURED FROM THE FLOOR.
<br />LIGHTING
<br />1. A MINIMUM OF FOUR BRANCH CIRCUITS SHALL BE IDENTIFIED
<br />AND HAVE THEIR SOURCE OF SUPPLY COLLOCATED AT A SINGLE
<br />PANELBOARD SUITABLE TO BE SUPPLIED BY THE ESS AT LEAST
<br />ONE CIRCUIT SHALL BE LOCATED NEAR THE PRIMARY EGRESS AND
<br />AT LEAST ONE CIRCUIT SHALL SUPPLY A SLEEPING ROOM
<br />RECEPTACLE OUTLET.
<br />A. ALL RESIDENTIAL OUTDOOR LIGHTING PERMANENTLY
<br />MOUNTED TO THE RESIDENCE OR OTHER BUILDINGS ON THE
<br />SAME LOT BE HIGH -EFFICACY AND MEET THE FOLLOWING
<br />REQUIREMENTS (150(K) 3A CEC)
<br />1. LIGHTS SHALL COMPLY WITH ONE OF THE TWO OPTIONS
<br />BELOW:
<br />I. CONTROLLED BY A PHOTOCELL AND MOTION SENSOR.
<br />CONTROLS THAT
<br />OVERRIDE TO ON SHALL NOT BE ALLOWED UNLESS
<br />THE OVERRRIDE
<br />AUTOMATICALLY REACTIVATES THE MOTION
<br />SENSOR WITHIN 6 HOURS.
<br />II. CONTROLLED BY (1) PHOTOCONTROL AND AUTOMATIC TIME SWITCH
<br />CONTROL OR (2) ASTRONOMICAL TIME CLOCK OR (3) ENERGY MANAGEMENT
<br />CONTROL SYSTEM MEETING THE REQUIREMENTS OF 150(K)3A.
<br />note: written dimensions shall
<br />take preference over scaled
<br />dimensions and shall be rifled
<br />0 e�enllbn�eshgns
<br />prior to commencement of any
<br />H
<br />Cn
<br />F_
<br />r-
<br />§
<br />U
<br />Q
<br />ZQ
<br />O
<br />O
<br />O
<br />�
<br />N
<br />Q
<br />N
<br />>%
<br />LO
<br />~
<br />Z
<br />W
<br />��1
<br />V
<br />o
<br />a)
<br />U)
<br />LO
<br />O
<br />C
<br />�
<br />pQ
<br />T-
<br />r
<br />..
<br />N
<br />.O
<br />Q
<br />co
<br />O
<br />�
<br />W
<br />Z
<br />0
<br />Z
<br />a
<br />J
<br />Lu
<br />W
<br />IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
<br />�
<br />z
<br />VI
<br />0
<br />J
<br />Q
<br />u
<br />W
<br />0
<br />u
<br />C�
<br />■ J
<br />Q
<br />H
<br />Z
<br />W
<br />W
<br />CV
<br />co
<br />r`
<br />Q
<br />Cr E
<br />O °
<br />�L
<br />JO �
<br />QCyD E
<br />U� 0-�
<br />UJ I
<br />z-t CD
<br />OLO o
<br />:�i^
<br />JQ0 E
<br />Lu Cat .0)
<br />� �
<br />} aD
<br />_M
<br />OM
<br />Q J_
<br />O Q
<br />= W
<br />O
<br />CE
<br />00
<br />r
<br />00
<br />r
<br />DATE
<br />SCALE AS NOTED
<br />DRAWN: SA
<br />SHEET
<br />04-
<br />E
<br />
|