Laserfiche WebLink
400 Sunrise Ave., Suite 270 <br />Roseville, CA 95661 <br />916.755.3571 / MiTek-US.com <br />Design valid for use only with MiTek® connectors. This design is based only upon parameters shown, and is for an individual building component, not <br />a truss system. Before use, the building designer must verify the applicability of design parameters and properly incorporate this design into the overall <br />building design. Bracing indicated is to prevent buckling of individual truss web and/or chord members only. Additional temporary and permanent bracing <br />is always required for stability and to prevent collapse with possible personal injury and property damage. For general guidance regarding the <br />fabrication, storage, delivery, erection and bracing of trusses and truss systems, see ANSI/TPI1 Quality Criteria and DSB-22 available from Truss Plate Institute (www.tpinst.org) <br />BCSI Building Component Safety Information <br />WARNING - Verify design parameters and READ NOTES ON THIS AND INCLUDED MITEK REFERENCE PAGE MII-7473 rev. 1/2/2023 BEFORE USE. <br />and available from the Structural Building Component Association (www.sbcscomponents.com) <br />=4x6 <br />=4x6 <br />=3x4 <br />=3x4 <br />=6x16 <br />=4x5 <br />=6x8 <br />6 <br />12 5 13 <br />48 <br />9 <br />1 2 11 310 <br />7 <br />0-5-10 <br />0-5-10 <br />5-3-15 <br />5-9-9 <br />6-2-15 <br />12 -0-8 <br />0-7-8 <br />12-0-8 <br />5-7-7 <br />11-5-0 <br />5-9-9 <br />5-9-9 <br />5-6-0 <br />1-11 <br />-15 <br />0-9-4 <br />2-9-3 <br />2-9-3 <br />2-8-13 <br />5-6-0 <br />Scale = 1:41.3 <br />Plate Offsets (X, Y):[1:0-3-0,Edge], [3:0-5-4,0-3-4], [4:Edge,0-3-9] <br />Loading (psf)Spacing 2-0-0 CSI DEFL in (loc)l/defl L/d PLATES GRIP <br />TCLL (roof)20.0 Plate Grip DOL 1.25 TC 0.62 Vert(LL)-0.12 5-6 >999 360 MT20 220/195 <br />TCDL 14.0 Lumber DOL 1.25 BC 0.62 Vert(CT)-0.17 5-6 >794 240 <br />BCLL 0.0 *Rep Stress Incr NO WB 0.49 Horz(CT)0.01 9 n/a n/a <br />BCDL 7.0 Code IBC2021/TPI2014 Matrix-MSH Wind(LL)0.02 5 >999 240 Weight: 69 lb FT = 20% <br />LUMBER <br />TOP CHORD 2x4 DF No.2 G <br />BOT CHORD 2x4 DF No.2 G <br />WEBS 2x4 DF No.2 G or 2x4 DF Std G or 2x4 DF <br />Stud G *Except* 7-6:2x6 DF No.2 G <br />OTHERS 2x8 DF No.2 G <br />BRACING <br />TOP CHORD 2-0-0 oc purlins (6-0-0 max.): 1-3, 1-7, <br />except end verticals. <br />BOT CHORD Rigid ceiling directly applied or 9-10-4 oc <br />bracing. <br />REACTIONS (size)6=0-5-8, 9=0-5-8 <br />Max Horiz 6=-154 (LC 10) <br />Max Uplift 6=-56 (LC 8), 9=-55 (LC 9) <br />Max Grav 6=623 (LC 29), 9=583 (LC 32) <br />FORCES (lb) - Maximum Compression/Maximum <br />Tension <br />TOP CHORD 1-2=-348/247, 2-3=-766/396, 4-8=0/418, <br />3-8=0/418, 1-6=-450/112, 1-7=0/0 <br />BOT CHORD 5-6=-405/766, 4-5=-83/208 <br />WEBS 2-5=-217/206, 3-5=-353/711, 2-6=-806/471, <br />3-9=-615/253 <br />NOTES <br />1)Unbalanced roof live loads have been considered for <br />this design. <br />2)Wind: ASCE 7-16; Vult=96mph (3-second gust) <br />Vasd=76mph; TCDL=8.4psf; BCDL=4.2psf; h=25ft; Cat. <br />II; Exp C; Enclosed; MWFRS (envelope) exterior zone <br />and C-C Corner (3) zone; cantilever left and right <br />exposed ; end vertical left and right exposed;C-C for <br />members and forces & MWFRS for reactions shown; <br />Lumber DOL=1.60 plate grip DOL=1.60 <br />3)Provide adequate drainage to prevent water ponding. <br />4)This truss has been designed for a 10.0 psf bottom <br />chord live load nonconcurrent with any other live loads. <br />5)* This truss has been designed for a live load of 20.0psf <br />on the bottom chord in all areas where a rectangle <br />3-06-00 tall by 2-00-00 wide will fit between the bottom <br />chord and any other members. <br />6)A plate rating reduction of 20% has been applied for the <br />green lumber members. <br />7)Bearings are assumed to be: Joint 6 DF No.2 crushing <br />capacity of 625 psi, Joint 9 DF No.2 crushing capacity of <br />625 psi. <br />8)Bearing at joint(s) 9 considers parallel to grain value <br />using ANSI/TPI 1 angle to grain formula. Building <br />designer should verify capacity of bearing surface. <br />9)Provide mechanical connection (by others) of truss to <br />bearing plate capable of withstanding 56 lb uplift at joint <br />6 and 55 lb uplift at joint 9. <br />10)This truss has been designed for a moving concentrated <br />load of 300.0lb live and 80.0lb dead located at all mid <br />panels and at all panel points along the Top Chord and <br />Bottom Chord, nonconcurrent with any other live loads. <br />11)Graphical purlin representation does not depict the size <br />or the orientation of the purlin along the top and/or <br />bottom chord. <br />12)This truss is designed for a creep factor of 2.01, which is <br />used to calculate the Vert(CT) deflection per ANSI/TPI 1. <br />The building designer shall verify that this parameter fits <br />with the intended use of this component. <br />LOAD CASE(S) Standard <br />Job Truss Truss Type Qty Ply M39558- TOMS JR SANTA ANA <br />R80031761AC04Flat11M39885- TOMS JR Job Reference (optional) <br />Builders FirstSource (Perris, CA), Perris, CA - 92570,Run: 8.63 S Nov 1 2023 Print: 8.630 S Nov 1 2023 MiTek Industries, Inc. Wed Dec 27 09:55:40 Page: 1 <br />ID:z?qsoDPH7L5ik_5e60ru_YyEmsF-RfC?PsB70Hq3NSgPqnL8w3uITXbGKWrCDoi7J4zJC?f <br />December 27,2023 <br />1430 E Edinger Ave <br />3/27/2025