1430 E Edinger Ave-REV 1 - Plan - Laserfiche WebLink

Home Browse Search

11' - 3" 4' - 0 " 5' - 0 " WINDOW "A" TYPE WINDOW "B" TYPE 5' - 7 1/2"5' - 7 1/2" TEMP GLASS TEMP GLASS PLAN VIEW 1' - 0 " 8'-0" PER MANUF 36" A.F.F. S.S. SHELF BUTT JOINT CORNER GLAZING 3' - 0 " 8'-0" PER MANUF 6' - 0 " 3' - 0 " PER MANUFACTURER TEMP GLASS TEMPERED GLASS w/ Self-Closing Mechanism TEMP GLASS SIDE VIEW TEMP GLASS TEMP GLASS WINDOW "D" TYPE 4' - 0 " 5' - 0 " TEMP GLASS 22' - 0" WINDOW "E" TYPE 9' - 0 " 6' - 6" GLASS DOOR 36" WIDE TEMP GLASS TEMP GLASS WINDOW "F" TYPE 6' - 5" TEMP GLASS TEMP GLASSTEMP GLASSTEMP GLASS 7' - 2 1/2"7' - 1"7' - 8 1/2" WINDOW "G" TYPE 9' - 0 " 3' - 8 1/2"9' - 0"9' - 0" 21' - 8 1/2" TEMP GLASS TEMP GLASS TEMP GLASS TEMP GLASS TEMP GLASS TEMP GLASS WINDOW "H" TYPE 6' - 0" 7' - 0 " 2' - 0 " TEMP GLASS 7' - 0 " 3' - 6" 7' - 0 " 3' - 0" 2 3 5 8 6 1 4 7 9 DOORS #7 & #9 AT ELECTRICAL ROOM SHALL BE STEEL WITH LOUVERS 2'-6" WIDE DOUBLE DOOR WINDOW "C" TYPE 2' - 1 0 " 6' - 2 " 9' - 0 " 4' - 7" 8' - 0 " 5'-0" MTL DOOR 9 7' - 6 " 7' - 6 " Tempered Glass w/ Self-Closing Mechanism 9' - 0 " THRESHOLD DETAIL 6/A-003 5/A-003 THRESHOLD DETAIL 6/A-003 5/A-003 THRESHOLD DETAIL 6/A-003 5/A-003 THRESHOLD DETAIL 6/A-003 5/A-003 THRESHOLD DETAIL 6/A-003 5/A-003 GENERAL WINDOW NOTES: 1. ALL WINDOW ROUGH OPENINGS (R.O.) SHOULD BE BASED ON MANUFACTURER'S ORDERED SIZES, SPECIFICATIONS, RECOMMENDATIONS AND DETAILS. 2. ROUGH FRAMING SUBCONTRACTOR IS RESPONSIBLE FOR PROVIDING ALL FRAMING, NAILERS AND FILLERS AS SHOWN ON DOOR DETAILS AND AS MAY OTHERWISE BE REQUIRED FOR PROPER INSTALLATION OF ALL WINDOWS REFER TO DETAILS. 3. ALL WINDOW DETAILS SHOULD MEET OR EXCEED DETAILS AND SPECIFICATIONS OR AN OWNER AND ARCHITECT APPROVED EQUAL SUBSTITUTE. 4. SHOP DRAWINGS OF ALL WINDOW TYPES MUST BE SUBMITTED TO THE ARCHITECT FOR APPROVAL PRIOR TO FABRICATION. 5. REFER TO GENERAL NOTES FOR TYPICAL REQUIREMENTS APPLICABLE TO WINDOWS 6. ALL WINDOWS TO BE INSTALLED IN STRICT ACCORDANCE WITH MANUFACURER'S SPECIFICATIONS AND RECOMMENDATIONS TO INSURE PRODUCT WARRANTY 7. WINDOW GLAZING TO BE DUAL GLAZING. 8. NOT USED 9. ALL EXTERIOR JAMBS TO BE BACK-PRIMED PRIOR TO INSTALLATION. 10. REFER TO THE ENERGY CALCS REPORT (T24) FOR REQUIRED 'U' & SHGC VALUES. 11. SEE EXTERIOR ELEVATIONS FOR DEMARKATION OF DIRECTION OF SWING ON ALL WINDOWS. 12. EVERY SLEEPING ROOM SHALL HAVE AT LEAST ONE EXTERIOR DOOR OR WINDOW OPEN DIRECTLY INTO A YARD OR EXIT COURT FOR EMERGENCY EGRESS. WINDOWS MUST PROVIDE THE FOLLOWING SITUATION: MINIMUM 5.7 SQUARE FEET OF OPENABLE AREA CLEAR, MINIMUM CLEAR WIDTH OF 20", MINIMUM CLEAR HEIGHT OF 24" AND A FINISH SILL HEIGHT NOT MORE THAN 44" ABOVE FINISH FLOOR. (PER CBC 2022) 13. ALL GLAZING IN HAZARDOUS LOCATIONS MUST BE IDENTIFIED BY A LABEL (PERMANENT IF TEMPERED) AS SAFTEY GLAZING: (PER CBC 2022). A. GLAZING IN ALL DOORS B. GLAZING IN BATH AND SHOWER ENCLOSURES C. ALL GLAZING WITHIN 24" ARC OF THE DOOR EDGE D. PANELS OVER 9 SQ. FT. IN AREA HAVING THE LOWEST EDGE LESS THAN 18" ABOVE THE FINISH FLOOR AND HAVING A TOP EDGE GREATER THAN 36" ABOVE THE FLOOR 14. ANY GLASS AREA 9 SQUARE FEET OR LARGER IN SIZE TO BE SAFTEY GLASS. GENERAL DOOR NOTES: 1. ALL SCHEMATIC DOOR TYPES ARE NOT TO SCALE. REFER TO ABOVE SCHEDULE FOR DIMENSIONS. AND FIELD VERIFY EXISTING DEMOLISHED DOORS TO BE REPLACED. 2. ALL EXTERIOR DOORS TO BE DELIVERED TO JOB SITE AS COMPLETE UNITS. 3. ALL DOOR AND WINDOW HARDWARE TO BE ON AN ALLOWANCE OWNER / INTERIOR DESIGNER SELECTION. 4. REFER TO CF-1R FORM IN TITLE-24 ENERGY CALCULATIONS FOR REQUIRED 'U' VALUES. 5. DOOR SAMPLE TO BE APPROVED BY OWNER AND ARCHITECT BEFORE PLACING DOOR ORDER. 6. ALL DOORS TO BE INSTALLED IN STRICT ACCORDANCE WITH MANUFACTURER'S SPECIFICATIONS AND RECOMMENDATIONS. 7. ROUGH FRAMING SUBCONTRACTOR IS RESPONSIBLE FOR PROVIDING ALL FRAMING, NAILERS AND FILLERS AS SHOWN ON DOOR DETAILS AND AS MAY OTHERWISE BE REQUIRED FOR PROPER INSTALLATION OF ALL DOORS. INCLUDING HEIGHTS OF HEADERS / BEAMS SUPPORTING DOORS & HARDWARE. SUBCONTRACTOR SHALL COORDINATE WITH MANUFACTURER FOR DOOR CLEARANCES & INSTALLATION. 8. GARAGE DOORS WITH ELECTRIC GARAGE DOOR OPENERS TO HAVE ELECTRIC EYE SAFETY DEVICE MOUNTED AT HEIGHT REQUIRED BY MANUFACTURER AND LOCAL GOVERNING BODY. 9. ANY GLASS AREA 9 SQUARE FEET OR LARGER IN SIZE TO BE TEMPERED. TERMPERED GLASS IN HAZARDOUS LOCATIONS PER U.B.C. SEC 2406.4 A. INGRESS AND EGRESS DOORS B. PANELS IN SLIDING OR SWINGING DOORS OTHER THAN WARDROBE DOORS. C. DOORS AND ENCLOSURES FOR HOT TUB, BATHRUB, SHOWERS (ALSO GLAZING IN WALL ENCLOSING THESE COMPARTMENTS WITHIN 5' OF STANDING SURFACE) D. IF WITHIN 2 FT. OF VERTICAL EDGE OF CLOSED DOOR AND WITHIN 5 FT. OF STANDING SURFACE E. IN WALL ENCLOSING STAIRWAY LANDING 10. SAFTEY GLASS IS REQUIRED AT WARDROBE DOOR. CBC 2022 11. PROVIDE DOOR STOPS WHEREVER NECESSARY. 12. FINAL FINISH SELECTION FOR DOORS BY OWNER, ARCHITECT, AND INTERIOR DESIGNER. NOTE: NOT ALL GENERAL DOOR & WINDOWS NOTE(S) MAY APPLY, CONTACT ARCHITECT FOR CLARRIFICATIONS. Safety Glazing PER CBC 2022 & (R308.4/CBC 2406) 2406.4 Hazardous Locations. The following shall be considered specific hazardous locations for the purposes of glazing: 1. Glazing in ingress and egress doors except jalousies. 2. Glazing in fixed and sliding panels of sliding door assemblies and panels in swinging doors other than wardrobe doors. 3. Glazing in storm doors. 4. Glazing in all unframed swinging doors. 5. Glazing in doors and enclosures for hot tubs, whirlpools, saunas, steam rooms, bathtubs and showers. Glazing in any portion of a building wall enclosing these compartments where the bottom exposed edge of the glazing is less than 60 inches (1525 mm) above a standing surface and drain inlet. 6. Glazing in fixed or operable panels adjacent to a door where the nearest exposed edge of the glazing is within a 24-inch (610 mm) arc of either vertical edge of the door in a closed position and where the bottom exposed edge of the glazing is less than 60 inches (1525 mm) above the walking surface. 7. Glazing in an individual fixed or operable panel, other than those locations described in Items 5 and 6 above, that meets all of the following conditions: 7.1 Exposed area of an individual pane greater than 9 square feet (0.84 ). 7.2 Exposed bottom edge less than 18 inches (457 mm) above the floor. 7.3 Exposed top edge greater than 36 inches (914 mm) above the floor. 7.4 One or more walking surfaces within 36 inches (914 mm) horizontally of the plane of the glazing. 8. Glazing in railings regardless of height above a walking surface. Included are structural baluster panels and nonstructural in-fill panels. EXCEPTION: The following products and applications are exempt from the requirements for hazardous locations as listed in Items 1 through 8 above: 1. Glazing in Item 6 when there is an intervening wall or other permanent barrier between the door and the glazing. 2. Glazing in Item 7 when a protective bar is installed on the accessible sides of the glazing 34 inches (864 mm) to 38 inches (965 mm) above the floor. The bar shall be capable of withstanding a horizontal load of 50 pounds per linear foot (729 N/m) without contacting the glass and be a minimum of 1 1/2 inches (38.1 mm) in height. 3. Outboard pane in insulating glass units and in other multiple glazed panels in Item 7 when the bottom exposed edge of the glass is 25 feet (7620 mm) or more above any grade, roof, walking surface or other horizontal or sloped (within 45 degrees of horizontal) surface adjacent to the glass exterior. 4. Openings in door through which a 3-inch-diameter (76.2 mm) sphere will not pass. 5. Assemblies of leaded, faceted or carved glass in Items 1, 2, 6 and 7 when used for decorative purposes. 6. Curved panels in revolving door assemblies. 7. Doors in commercial refrigerated cabinets. 8. Glass block panels complying with Section 2110. 9. Glazing in walls and fences used as the barrier for indoor and outdoor swimming pools and spas when all of the following conditions are present: 9.1 The bottom edge of the glazing is less than 60 inches (1525 mm) above the pool side of the glazing. 9.2 The glazing is within 5 feet (1525 mm) of a swimming pool or spa deck area. 10. Glazing in walls enclosing stairway landings or within 5 feet (1525 mm) of the bottom and top of stairways where the bottom edge of the glass is less than 60 inches (1525 mm) above a walking surface. 2406.5 Wardrobe Doors. Glazing in wardrobe doors shall meet the impact test requirements for safety glazing as set forth in U.B.C. Standard 24-2, Part II. Laminated glass must also meet the boil test requirements of U.B.C. Standard 24-2, Part II. EXCEPTION: The impact test shall be modified so that if no breakage occurs when the impacting object is dropped from the height of 18 inches (457 mm), the test shall progress in height increments of 6 inches (152.5 mm) until the maximum of 48 inches (1219 mm) is reached. 2406.6 Glass Railings. Glass used as structural balustrade panels in railings shall be one of the following types: 1. Single fully tempered glass. 2. Laminated fully tempered glass. 3. Laminated heat-strengthened glass. The panels and their support system shall be designed to withstand the load specified in Table 16-B. A safety factor of 4 shall be used. Each handrail or guardrail section shall be supported by a minimum of three glass balusters or otherwise supported so that it remains in place should one baluster panel fail. Glass balusters shall not be installed without a handrail or guardrail attached. For all glazing types the minimum nominal thickness shall be 1/4 inch (6.35 mm). Glazing materials shall not be installed in railings in parking garages except for those locations where the railing is not exposed to impact from vehicles. A. EXIT DOORS SHALL BE EQUIPPED WITH PANIC HARDWARE. S.S. HARDWARE FINISH EXTERIOR DOOR LOCKSET 34" TO 48" A.F.F. SUGATSUNE DSI-2000-30-60I, DORMA BTSBO CLOSER OR EQUAL PER CONTRACTOR. SUBMIT TO CLIENT SPECIFICATIONS. B. SINGLE INTERIOR DOOR LATCHSET 34" TO 48" A.F.F. FALCON T- SERIES DANE GRADE I COMMERCIAL PASSAGE FUNCTION C. EGRESS DOORS/GATES SHALL BE READILY OPENABLE FROM THE EGRESS SIDE WITHOUT THE USE OF A KEY OR SPECIAL KNOWLEDGE OR EFFORT. (1010.1.9) D. OPENABLE PARTS OF SUCH HARDWARE SHALL BE 34 INCHES MINIMUM AND 44 INCHES MAXIMUM ABOVE THE FINISH FLOOR OR GROUND. E. THE FORCE FOR PUSHING OR PULLING OPEN A DOOR SHALL BE 5- LB MAXIMUM. F. OPERABLE PARTS SHALL BE OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. G. A READILY VISIBLE DURABLE SIGN POSTED ON THE EGRESS SIDE ON OR ADJACENT TO THE MAIN EXIT DOOR STATING: "THIS DOOR TO REMAIN UNLOCKED WHEN THIS SPACE IS OCCUPIED", IS REQUIRED. (1010.1.9.4) NOTE: ALL DOORS MUST MEET CITY OF SANTA ANA BUILDING & POLICE DEPARTMENT APPROVAL & REQUIREMENTS. DOOR HARDWARE SHALL BE ADA & MEET CBC 2022 ACCESSIBILITY REQUIREMENTS, SUBMIT FULL SHOP DRAWINGS FOR ALL DOORS. DOOR HARDWARE NOTES: 1. ALL LOCK SETS TO BE RE-KEYED PRIOR TO OWNER MOVE IN. VERIFY WITH CLIENT & ALL LOCK SETS TO FUNCTION FROM ONE KEY. HARDWARE NOTES: 1. STEEL OR ALUMINUM FRAME W/ SOLID CORE WOOD DOORS AND OR GLASS. PAINTED TO MATCH AS DIRECTED BY CLIENT. VERIFY W/ CLIENT MATERIAL AND FINISH INDEX: Scale Date Drawn By Checked By Project Number 14 3 0 E E D I N G E R A V E , S A N T A A N A , C A 9 2 7 0 5 NOVUM A R C H I T E C T U R E, Inc www.novumarchitecture.com OFFICES: SOUTH BAY / ORANGE COUNTY 116 S CATALINA AVE. STE. 122, REDONDO BEACH, CA 90277 TEL: 310-383-1827 / 310-709-4476 N DARIAN RADAC NO. C-33451 RENEWAL DATE LICENSED STA OE CETIHCRA T T F INR I O CALF A2-28-2025 Darian Radac As indicated A-017 TO M ' S J R Checker Author 9-03-2024 tom's2023 Do o r & W i n d o w S c h e d u l e s Mr . S p i r o s P o l i t i s Door Schedule Door Number Door Size Frame Type Fire Rating Description Finish Comments 1 Door-Curtain-Wall-Double-Storefront 2 36" x 80" 3 36" x 80" 4 Door-Curtain-Wall-Single-Glass 5 30" x 80" 6 36" x 108" 7 5' x 8' Metal Elec Room Door 8 42" x 80" E 36" x 80" E 36" x 84" Window Schedule Type Mark Rough Opening Manufacturer Material CommentsWidth Height 3/8" = 1'-0"1 Exterior Building Windows WALK IN COOLER DOOR BY MANUFACTURER WALK IN COOLER DOOR BY MANUFACTURER DOUBLE 3'-0" WIDE TEMP GLASS ENTRY STOREFRONT DOOR. SINGLE 3'-0" WIDE TEMP GLASS ENTRY STOREFRONT DOOR. PROVIDE PANIC HARDWARE. MTL N/A MTL N/A MTL N/A MTL N/A MTL N/A MTL N/A MTL N/A MTL N/A MTL N/A MTL N/A "A" TYPE "B" TYPE "C" TYPE "D" TYPE "E" TYPE "F" TYPE "G" TYPE "H" TYPE 11'-3" 5'-0" WESTERN OR EQUAL MTL REFER TO EXTERIOR ELEVATIONS, TEMP GLASS INSULATED UNITS PROVIDE LOUVERS PER MANUF SPECIFICATIONS 8'-0" 6'-0" WESTERN OR EQUAL MTL REFER TO EXTERIOR ELEVATIONS, TEMP GLASS INSULATED UNITS W/ SELF CLOSING MECHANISM. 4'-7" 6'-2" WESTERN OR EQUAL MTL REFER TO EXTERIOR ELEVATIONS, TEMP GLASS INSULATED UNITS W/ SELF CLOSING MECHANISM. 22'-0" 5'-0" WESTERN OR EQUAL MTL REFER TO EXTERIOR ELEVATIONS, TEMP GLASS INSULATED UNITS 6'-6" 1'-6" WESTERN OR EQUAL MTL REFER TO EXTERIOR ELEVATIONS, TEMP GLASS INSULATED UNITS 6'-5" 1'-6" WESTERN OR EQUAL MTL REFER TO EXTERIOR ELEVATIONS, TEMP GLASS INSULATED UNITS 21'-8.5" 5'-0" WESTERN OR EQUAL MTL REFER TO EXTERIOR ELEVATIONS, TEMP GLASS INSULATED UNITS 6'-0" 2'-0" WESTERN OR EQUAL MTL REFER TO EXTERIOR ELEVATIONS, TEMP GLASS INSULATED UNITS No. Description Date PROVIDE PANIC HARDWARE. 1430 E Edinger Ave 3/27/2025