Laserfiche WebLink
SLIDE AROUND CLEATFIELD BEND PANEL <br />(OVERHANG 1")OFFSET CLEAT <br />STANDING SEAM PANEL SELF-DRILLING SCREWS#10x1" PANCAKE HEAD <br />ROOF CLIP <br />EAVE BEAM <br />2013C <br />EAVE DETAIL SS-102 <br />AND SIDES)(ALONG TOP, BOTTOM,BUTYL TAPE <br />EACH SIDE OF RIBDRILLING SCREW#12-14 X 3/4" SELF <br />STANDING SEAM PANEL <br />C-CLOSURE <br />12" O.C.DRILLING SCREW#12-14 X 3/4" SELF <br />RAKE TRIM <br />EAVE BEAM <br />2013C <br />HIGH SIDE DETAIL (VIEWING FROM ABOVE)SS-202 <br />PURLIN <br />ROOF CLIP <br />SELF-DRILLING SCREWS#10x1" PANCAKE HEAD <br />TAILAND/ OR <br />STANDING SEAM PANEL <br />SS-600PURLIN DETAIL <br />2013C <br />16" <br />3/8"1/8" <br />1 3/4" <br />SS-950ROOF DECK SECTION PROPERTIES <br />GENERAL:GAGE = 22 Fy = 50 KSI <br />TOP IN COMPRESSION;Ix=0.12000 IN^4Se=0.0803 IN^3Ma=2.4050 IN-KIPS <br />BOTTOM IN COMPRESSION:Ix=0.0570 IN^4Se=0.0729 IN^3Ma=1.722 IN-KIPS <br />BEND DOWNTRIM THE RIBS BACK 1-1/2" <br />HEMMING DETAIL SS-HEM <br />1 1/2" <br />SS-CLP <br />2013C <br />CLIP DETAIL <br />NOTES:1. CLIPS MUST BE PROVIDED BY ROOF PANEL MANUFACTURER AS PART OF ROOF SYSTEM, <br />2. MATERIAL THICKNESS MUST BE 18 GAGE (0.048"-0.053") <br />1.875 <br />.85 1.161.500 <br />1.16 <br />3.750 <br />3.500 <br /> THRU.246Ø2X <br />1.300 <br />1.225 <br />.45 <br />AND ENDS)(ALONG TOP, BOTTOM,BUTYL TAPE <br />12" O.C.1/8" X 5/16" POP RIVET <br />RAKE CLOSURE <br />TOP AND SIDE12" O.C.DRILLING SCREW#12-14 X 3/4" SELF <br />RAKE TRIM <br />STANDING SEAM PANEL <br />TRUSS <br />SS-400RAKE DETAIL <br />2013C <br />STATE APPROVALS-PC <br />STATE APPROVALS-SITE <br />PR <br />E <br />- <br />C <br />H <br />E <br />C <br />K <br /> <br />( <br />P <br />C <br />) <br /> <br />DO <br />C <br />U <br />M <br />E <br />N <br />T <br />CO <br />D <br />E <br />: <br /> <br />2 <br />0 <br />2 <br />2 <br /> <br />C <br />B <br />C <br />A <br />S <br />E <br />P <br />A <br />R <br />A <br />T <br />E <br /> <br />P <br />R <br />O <br />J <br />E <br />C <br />T <br /> <br />AP <br />P <br />L <br />I <br />C <br />A <br />T <br />I <br />O <br />N <br /> <br />F <br />O <br />R <br /> C <br />O <br />N <br />S <br />T <br />R <br />U <br />C <br />T <br />I <br />O <br />N <br /> <br />I <br />S <br /> <br />R <br />E <br />Q <br />U <br />I <br />R <br />E <br />D <br />. <br />MSL6.1 <br />SS-102 <br />MSL6.1 <br />SS-202 <br />MSL6.1 <br />SS-400 <br />MSL6.1 <br />SS-600 <br />MS <br />L <br />6 <br />. <br />1 <br />RO <br />O <br />F <br /> <br />C <br />O <br />N <br />N <br />E <br />C <br />T <br />I <br />O <br />N <br /> <br />DE <br />T <br />A <br />I <br />L <br />S <br />MO <br />N <br />O <br />S <br />L <br />O <br />P <br />E <br /> <br />- <br /> <br />M <br />S <br />L <br />STANDING SEAM INSTALLATION NOTES: <br />THE DETAILS SHOWN ARE SUGGESTIONS OR GUIDELINES ON <br />HOW TO ERECT THE SYSTEMS. THE INFORMATION SHOWN IS <br />ACCURATE, BUT IT IS NOT INTENDED TO COVER ALL INSTANCES, <br />BUILDING REQUIREMENTS, DESIGNS OR CODES. THE DETAILS <br />MAY REQUIRE CHANGES OR REVISIONS DUE TO FIELD <br />CONDITIONS. <br />IT SHALL BE THE RESPONSIBILITY OF THE ERECTOR TO ENSURE <br />THAT THE DETAILS MEET PARTICULAR BUILDING REQUIREMENTS <br />AND TO ASSURE ADEQUATE WATER TIGHTNESS. <br />THE ERECTOR SHOULD THOROUGHLY FAMILIARIZE <br />HIMSELF/HERSELF WITH ALL ERECTION INSTRUCTIONS BEFORE <br />STARTING WORK. <br />THE PANELS SHOULD BE INSTALLED PLUMB, STRAIGHT, AND <br />ACCURATELY TO THE ADJACENT WORK. <br />FLASHING AND TRIM SHALL BE INSTALLED TRUE, AND IN PROPER <br />ALIGNMENT, WITH ANY EXPOSED FASTENERS EQUALLY SPACED <br />FOR THE BEST APPEARANCE. <br />SEALANT SHALL BE FIELD APPLIED ON DRY, CLEAN SURFACES. <br />SOME FIELD CUTTING AND FITTING OF PANELS AND FLASHING IS <br />TO BE EXPECTED BY THE ERECTOR AND MINOR FIELD <br />CORRECTIONS ARE A PART OF NORMAL ERECTION WORK. <br />WORKMANSHIP SHALL BE OF THE BEST INDUSTRY STANDARDS <br />AND INSTALLATION SHALL BE PERFORMED BY EXPERIENCED <br />METAL CRAFTSMEN. <br />METAL SHAVINGS FROM DRILLING OR INSTALLATION OF ROOF <br />FASTENERS MUST BE CAREFULLY REMOVED FROM THE ROOF BY <br />BRUSHING OR SWEEPING AT THE END OF EACH DAY DURING <br />INSTALLATION. SHAVINGS LEFT ON THE ROOF WILL QUICKLY <br />RUST AND STAIN THE ROOF FINISH. <br />COVER ACCESS HOLES WITH GRACE ICE AND WATER SHIELD <br />BEFORE ATTACHING ROOF DECK. <br />METAL ROOFING PRODUCT AND INSTALLATION SHALL MEET ALL <br />REQUIREMENTS OF ICC-ES REPORT ESL-1082. <br />JESSICA E. NAPIER <br />No. S5476 <br />S T R U C T U R A L <br />DSA <br />D E P A R T M E N T O F G E N E R A L S E R V I C E S <br />DIVISION OF THE STATE ARCHITECT <br />DSA <br />DIVISION OF THE STATE ARCHITECT <br />DSA <br />DIVISION OF THE STATE ARCHITECT <br />DSA <br />DIVISION OF THE STATE ARCHITECT <br />IDENTIFICATION STAMP <br /> DIV. OF THE STATE ARCHITECT <br />APP: <br />REVIEWED FOR <br />SS FLS ACS <br />DATE: <br />CG444 <br />02-121212 <br />7/18/2023 <br />PC