322 N Harbor Blvd - Plan - Laserfiche WebLink

Home Browse Search

32 2 N . H A R B O R B L V D . SA N T A A N A , C A 9 2 7 0 3 SHEET NUMBER 2 0 2 4 0 1 0 SHEET TITLE PROJECT NUMBER REVISIONS NO.DATE NO.DATE HANNOUCHE ARCHITECTS EXPRESSLY RESERVES ITS COMMON LAW COPYRIGHT AND OTHER PROPERTY RIGHTS INHERENT IN THESE PLANS. ALL DRAWINGS, ELECTRONIC FILES, FIELD NOTES AND ASSOCIATED DOCUMENTS ARE INSTRUMENTS OF SERVICE AND ARE THE PROPERTY OF HANNOUCHE ARCHITECTS. ALL INFORMATION CONTAINED IN THESE DRAWINGS, ELECTRONIC FILES, FIELD NOTES AND ASSOCIATED DOCUMENTS IS PROJECT SPECIFIC AND SHALL NOT BE REPRODUCED, DISCLOSED, CHANGED, COPIED, OR USED OTHERWISE IN ANY FORM OR MANNER WHATSOEVER, WITHOUT FIRST OBTAINING THE EXPRESSED WRITTEN PERMISSION AND CONSENT OF HANNOUCHE ARCHITECTS. HANNOUCHE ARCHITECT c 2021 HANNOUCHE ARCHITECTS 949.261.2070 SAMIR HANNOUCHE, ARCHITECT 20250 SW ACACIA ST. #145 NEWPORT BEACH, CA 92660 May 9, 2025 1 CORR 12/10/24 BLDG A CORR 3/18/25 OCFA 2 CORR 4/09/25 BLDG DATE SIGNED2 3 CORR 5/09/25 BLDG A0.17 DWELLING ADA NOTES DETAILS SCALE: N/A SEC. 1127A.5 BATHING FACILITIES - 1127 A.5 BATHING FACILITIES 1127A.5.1 GENERAL. WHEN COMMON USE BATHING FACILITIES ARE PROVIDED FOR RESIDENTS OR GUESTS, INCLUDING SHOWERS, BATHTUBS OR LOCKERS, AT LEAST ONE OF EACH TYPE OF FIXTURE IN EACH FACILITY, AND NOT LESS THAN 1 PERCENT OF ALL FIXTURES, SHALL COMPLY WITH THIS SECTION. 1127A.5.2 BATHTUBS. BATHTUBS REQUIRED TO BE ACCESSIBLE SHALL COMPLY WITH THE FOLLOWING: 1127A.5.2.1 FLOOR SPACE. CLEARANCE IN FRONT OF BATHTUBS SHALL EXTEND THE LENGTH OF THE BATHTUB AND SHALL BE 48 INCHES (1219 MM) WIDE MINIMUM FOR FORWARD APPROACH AND 30 INCHES (762 MM) WIDE MINIMUM FOR PARALLEL APPROACH. A LAVATORY COMPLYING WITH SECTION 1127 A.3 (see detail XX this sheet) SHALL BE PERMITTED AT THE CONTROL END OF THE CLEARANCE. WHEN A PERMANENT SEAT IS PROVIDED AT THE HEAD END OF THE BATHTUB, THE CLEARANCE SHALL EXTEND 12 INCHES (305 MM) MINIMUM BEYOND THE WALL AT THE HEAD END OF THE BATHTUB. (SEE FIGURE 11A-9E) 1127A.5.2.2 SEAT. A REMOVABLE IN-TUB SEAT OR A PERMANENT SEAT AT THE HEAD END OF THE TUB SHALL BE PROVIDED. THE STRUCTURAL STRENGTH OF SEATS AND THEIR ATTACHMENTS SHALL COMPLY WITH SECTION 1127A. 4.4 (see detail XX this sheet). SEATS SHALL BE MOUNTED SECURELY AND SHALL NOT SLIP DURING USE. THE TOP OF BATHTUB SEATS SHALL BE 17 INCHES (432 MM) MINIMUM AND 19 INCHES (483 MM) MAXIMUM ABOVE THE BATHROOM FINISH FLOOR. THE DEPTH OF A REMOVABLE IN-TUB SEAT SHALL BE 15 INCHES (381 MM) MINIMUM AND 16 INCHES (406 MM) MAXIMUM. PERMANENT SEATS AT THE HEAD END OF THE BATHTUB SHALL BE 15 INCHES (381 MM) DEEP MINIMUM AND SHALL EXTEND FROM THE BACK WALL TO OR BEYOND THE OUTER EDGE OF THE BATHTUB. (SEE FIGURE 11A-9E). 1127A.5.2.3 GRAB BARS. GRAB BARS COMPLYING WITH SECTION 1127A.4 (see detail XX this sheet) SHALL BE PROVIDED IN ACCORDANCE WITH THIS SECTION. (SEE FIGURE 11A-9F) WHEN SEPARATE GRAB BARS ARE REQUIRED ON ADJACENT WALLS AT A COMMON MOUNTING HEIGHT, AN L-SHAPED OR U-SHAPED GRAB BAR MEETING THE DIMENSIONAL REQUIREMENTS OF THIS SECTION SHALL BE PERMITTED. 1. BATHTUBS WITH PERMANENT SEATS. TWO HORIZONTAL GRAB BARS SHALL BE INSTALLED ON THE BACK WALL. ONE SHALL BE LOCATED 33 INCHES (838 MM) MINIMUM AND 36 INCHES (914 MM) MAXIMUM ABOVE THE FINISH FLOOR MEASURED TO THE TOP OF THE GRIPPING SURFACE, AND THE OTHER SHALL BE LOCATED 8 INCHES (203 MM) MINIMUM AND 10 INCHES (254 MM) MAXIMUM ABOVE THE RIM OF THE BATHTUB. EACH GRAB BAR SHALL BE 48 INCHES (1219 MM) LONG MINIMUM, AND SHALL BE INSTALLED 15 INCHES (381 MM) MAXIMUM FROM THE HEAD END WALL AND 12 INCHES (305 MM) MAXIMUM FROM THE CONTROL END WALL. A GRAB BAR 24 INCHES (610 MM) LONG MINIMUM SHALL BE INSTALLED ON THE CONTROL END WALL AT THE FRONT EDGE OF THE BATHTUB. 2. BATHTUBS WITH REMOVABLE SEATS. TWO HORIZONTAL GRAB BARS SHALL BE INSTALLED ON THE BACK WALL. ONE SHALL BE LOCATED 33 INCHES (838 MM) MINIMUM AND 36 INCHES (914 MM) MAXIMUM ABOVE THE FINISH FLOOR MEASURED TO THE TOP OF THE GRIPPING SURFACE, AND THE OTHER SHALL BE LOCATED 8 INCHES (203 MM) MINIMUM AND 10 INCHES (254 MM) MAXIMUM ABOVE THE RIM OF THE BATHTUB. EACH GRAB BAR SHALL BE 24 INCHES (610 MM) LONG MINIMUM AND SHALL BE INSTALLED 24 INCHES (610 MM) MAXIMUM FROM THE HEAD END WALL AND 12 INCHES (305 MM) MAXIMUM FROM THE CONTROL END WALL. A GRAB BAR 24 INCHES (610 MM) LONG MINIMUM SHALL BE INSTALLED ON THE CONTROL END WALL AT THE FRONT EDGE OF THE BATHTUB. A GRAB BAR 12 INCHES (305 MM) LONG MINIMUM SHALL BE INSTALLED ON THE HEAD END WALL AT THE FRONT EDGE OF THE BATHTUB. 1127A.5.2.4 CONTROLS. FAUCETS AND CONTROLS (OTHER THAN DRAIN STOPPERS) SHALL BE LOCATED ON AN END WALL BETWEEN THE BATHTUB RIM AND GRAB BAR, AND BETWEEN THE OPEN SIDE OF THE BATHTUB AND THE CENTERLINE OF THE WIDTH OF THE BATHTUB. (SEE FIGURE 11A-9F.) CONTROLS SHALL BE OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO ACTIVATE CONTROLS SHALL BE NO GREATER THAN 5 POUNDS (22.2 N).1127 A.5.2.5 SHOWER SPRAY UNIT. A SHOWER SPRAY UNIT WITH A HOSE AT LEAST 59 INCHES (1524 MM) LONG THAT CAN BE USED BOTH AS A FIXED SHOWER HEAD AND AS A HAND-HELD SHOWER SHALL BE PROVIDED. THE SHOWER SPRAY UNIT SHALL HAVE AN ON/OFF CONTROL WITH A NON-POSITIVE SHUT-OFF IF AN ADJUSTABLE-HEIGHT SHOWER HEAD ON A VERTICAL BAR IS USED, THE BAR SHALL BE INSTALLED SO AS NOT TO OBSTRUCT THE USE OF THE GRAB BARS. 1127 A.5.2.6 BATHTUB ENCLOSURES. WHEN PROVIDED, ENCLOSURES FOR BATHTUBS SHALL NOT OBSTRUCT CONTROLS, FAUCETS, SHOWER AND SPRAY UNITS, OR OBSTRUCT TRANSFER FROM WHEELCHAIRS ONTO BATHTUB SEATS OR INTO BATHTUBS. ENCLOSURES ON BATHTUBS SHALL NOT HAVE TRACKS INSTALLED ON THE RIM OF THE OPEN FACE OF THE BATHTUB. 1127A.5.3 SHOWER COMPARTMENTS. SHOWER COMPARTMENTS REQUIRED TO BE ACCESSIBLE SHALL COMPLY WITH THIS SECTION. (SEE FIGURES 11A-9H, 11A-9I, 11A-9J AND 11A-9K) 1127A.5.3.1 SIZE AND CLEARANCE. 1. STANDARD ROLL-IN SHOWER COMPARTMENTS. STANDARD ROLL-IN SHOWER COMPARTMENTS SHALL MEET ONE OF THE FOLLOWING: 1.1 30 INCHES (762 MM) MINIMUM IN DEPTH AND 60 INCHES (1524 MM) MINIMUM IN WIDTH BETWEEN WALL SURFACES MEASURED AT CENTER POINTS OF OPPOSING SIDES, WITH A FULL OPENING WIDTH ON THE LONG SIDE. A CLEAR FLOOR SPACE 30 INCHES (914 MM) MINIMUM BY 60 INCHES (1524 MM) MINIMUM SHALL BE PROVIDED ADJACENT TO THE OPEN FACE OF THE SHOWER COMPARTMENT. 1.2 42 INCHES (1067 MM) IN WIDTH BETWEEN WALL SURFACES, AND 48 INCHES (1219 MM) MINIMUM IN DEPTH WITH AN ENTRANCE OPENING OF 42 INCHES (1067 MM). 2. ALTERNATE ROLL-IN SHOWER COMPARTMENTS. ALTERNATE ROLL-IN SHOWER COMPARTMENTS SHALL BE 36 INCHES (914 MM) MINIMUM IN DEPTH AND 60 INCHES (1524 MM) MINIMUM IN WIDTH BETWEEN WALL SURFACES MEASURED AT CENTER POINTS OF OPPOSING SIDES. A 36-INCH (914 MM) WIDE MINIMUM ENTRY SHALL BE PROVIDED AT ONE END OF THE LONG SIDE OF THE COMPARTMENT. 1127A.5.3.2 THRESHOLDS. THRESHOLDS IN ROLL-IN SHOWER COMPARTMENTS SHALL BE 1/2 INCH (12.7 MM) MAXIMUM IN HEIGHT AND SHALL BE BEVELED WITH A SLOPE NO GREATER THAN ONE UNIT VERTICAL IN TWO UNITS HORIZONTAL (50-PERCENTSLOPE). (SEE FIGURE 11A-1F.) EXCEPTION:CHANGES IN LEVEL NOT EXCEEDING 1/4 INCH (6.35 MM) SHALL BE PERMITTED TO BE VERTICAL 1127A.5.3.3 ENCLOSURES. ENCLOSURES, WHEN PROVIDED FOR SHOWER COMPARTMENTS, SHALL NOT OBSTRUCT CONTROLS, FAUCETS, SHOWER SPRAY UNITS, AND TRANSFER FROM WHEELCHAIRS ONTO SHOWER SEATS. 1127 A.5.3.4 FLOOR. SHOWER COMPARTMENT FLOOR SURFACES SHALL BE STABLE, FIRM AND SLIP RESISTANT. THE MAXIMUM SLOPE OF THE FLOOR SHALL BE 1/4 INCH (6.35 MM) PER FOOT (2.083 PERCENT SLOPE) IN ANY DIRECTION. WHEN DRAINS ARE PROVIDED, GRATE OPENINGS SHALL BE 1/4 INCH (6.35 MM) MAXIMUM AND LOCATED FLUSH WITH THE FLOOR SURFACE. 1127 A.5.3.5 CONTROLS. CONTROLS, FAUCETS AND SHOWER SPRAY UNITS IN SHOWER COMPARTMENTS SHALL BE OPERABLE WITH ONE HAND, AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO ACTIVATE OPERABLE PARTS SHALL BE 5 POUNDS (22.2 N) MAXIMUM. ALL CONTROLS AND FAUCETS SHALL BE OF A SINGLE-LEVER DESIGN. 1127A.5.3.5.1 STANDARD ROLL-IN SHOWER COMPARTMENTS. IN STANDARD ROLL-IN SHOWER COMPARTMENTS, OPERABLE PARTS OF CONTROLS AND FAUCETS SHALL BE INSTALLED ON THE BACK WALL OF THE COMPARTMENT ADJACENT TO THE SEAT WALL, 19 INCHES (483 MM) MINIMUM AND 27 INCHES (686 MM) MAXIMUM FROM THE SEAT WALL. OPERABLE PARTS OF CONTROLS AND FAUCETS SHALL BE LOCATED ABOVE THE GRAB BAR, BUT NO HIGHER THAN 48 INCHES ( 1219 MM) ABOVE THE SHOWER FLOOR, WITH THEIR CENTERLINE AT 39 INCHES (991 MM) MINIMUM AND 41 INCHES ( 1041 MM) MAXIMUM ABOVE THE SHOWER FLOOR. OPERABLE PARTS OF THE SHOWER SPRAY UNIT, INCLUDING THE HANDLE, SHALL BE INSTALLED ON THE BACK WALL ADJACENT TO THE SEAT WALL, 19 INCHES (483 MM) MINIMUM AND 27 INCHES (686 MM) MAXIMUM FROM THE SEAT WALL. OPERABLE PARTS OF THE SHOWER SPRAY UNIT, INCLUDING THE HANDLE, SHALL BE LOCATED ABOVE THE GRAB BAR, BUT NO HIGHER THAN 48 INCHES (1219 MM) ABOVE THE SHOWER FLOOR (MEASURED TO THE TOP OF THE MOUNTING BRACKET). 1127 A.5.3.5.2 ALTERNATE ROLL-IN SHOWER COMPARTMENTS. IN ALTERNATE ROLL-IN SHOWER COMPARTMENTS, OPERABLE PARTS OF CONTROLS AND FAUCETS SHALL BE INSTALLED ON THE SIDE WALL OF THE COMPARTMENT ADJACENT TO THE SEAT WALL, 19 INCHES (483 MM) MINIMUM AND 27 INCHES ( 686 MM) MAXIMUM FROM THE SEAT WALL. OPERABLE PARTS OF CONTROLS AND FAUCETS SHALL BE LOCATED ABOVE THE GRAB BAR, BUT NO HIGHER THAN 48 INCHES (1219 MM) ABOVE THE SHOWER FLOOR, WITH THEIR CENTERLINE AT 39 INCHES (991 MM) MINIMUM AND 41 INCHES (1041 MM) MAXIMUM ABOVE THE SHOWER FLOOR. OPERABLE PARTS OF THE SHOWER SPRAY UNIT, INCLUDING THE HANDLE, SHALL BE INSTALLED ON THE FOLLOWING LOCATIONS: 1. ON THE SIDE WALL OF THE COMPARTMENT ADJACENT TO THE SEAT WALL, 17 INCHES (432 MM) MINIMUM AND 19 INCHES (483 MM) MAXIMUM FROM THE SEAT WALL; OR 2. ON THE BACK WALL OPPOSITE THE SEAT, 15 INCHES (381 MM) MAXIMUM, LEFT OR RIGHT, OF THE CENTERLINE OF THE SEAT. OPERABLE PARTS OF THE SHOWER SPRAY UNIT, INCLUDING THE HANDLE, SHALL BE LOCATED ABOVE THE GRAB BAR, BUT NO HIGHER THAN 48 INCHES (1219 MM) ABOVE THE SHOWER FLOOR. 1127 A.5.3.6 HAND-HELD SHOWER SPRAYER UNIT. A FLEXIBLE HAND-HELD SHOWER SPRAY UNIT WITH A HOSE AT LEAST 59 INCHES (1524 MM) LONG THAT CAN BE USED BOTH AS A FIXED SHOWER HEAD AND AS A HAND-HELD SHOWER SHALL BE PROVIDED. THE SHOWER SPRAY UNIT SHALL HAVE AN ON/OFF CONTROL WITH A NON-POSITIVE SHUT-OFF IF AN ADJUSTABLE-HEIGHT SHOWER HEAD ON A VERTICAL BAR IS USED, THE BAR SHALL BE INSTALLED SO AS NOT TO OBSTRUCT THE USE OF GRAB BARS. 1127A.5.3.6.1 SPRAYER UNIT ALTERNATIVE. WHEN ACCESSIBLE SHOWER FACILITIES ARE PROVIDED IN AREAS SUBJECT TO EXCESSIVE VANDALISM, IN LIEU OF PROVIDING THE FIXED FLEXIBLE HOSE, TWO WALL-MOUNTED SHOWER HEADS SHALL BE INSTALLED. EACH SHOWER HEAD SHALL BE INSTALLED SO THAT IT CAN BE OPERATED INDEPENDENTLY OF THE OTHER AND SHALL HAVE SWIVEL ANGLE ADJUSTMENTS, BOTH VERTICALLY AND HORIZONTALLY. ONE SHOWER HEAD SHALL BE LOCATED AT A HEIGHT OF 48 INCHES (1219 MM) MAXIMUM ABOVE THE FLOOR. 1127 A.5.3. 7 SHOWER COMPARTMENT SEATS. A SEAT IN A STANDARD ROLL-IN SHOWER COMPARTMENT SHALL BE A FOLDING TYPE, INSTALLED ON THE SIDE WALL ADJACENT TO THE CONTROLS. THE SEAT SHALL EXTEND FROM THE BACK WALL TO A POINT WITHIN 3 INCHES (76 MM) OF THE COMPARTMENT ENTRY. A SEAT IN AN ALTERNATE ROLL-IN TYPE SHOWER COMPARTMENT SHALL BE A FOLDING TYPE, INSTALLED ON THE FRONT WALL OPPOSITE THE BACK WALL, AND SHALL EXTEND FROM THE ADJACENT SIDE WALL TO A POINT WITHIN 3 INCHES (76 MM) OF THE COMPARTMENT ENTRY. SHOWER COMPARTMENT SEATS SHALL COMPLY WITH SECTION 1127 A.4.4 (see detail XX this sheet) AND SHALL BE LOCATED WITHIN 27 INCHES (686 MM) OF THE SHOWER CONTROLS. THE TOP OF THE SEAT SHALL BE 17 INCHES (432 MM) MINIMUM AND 19 INCHES (483 MM) MAXIMUM ABOVE THE BATHROOM FINISH FLOOR. WHEN FOLDED, THE SEAT SHALL NOT EXTEND MORE THAN 6 INCHES (152 MM) FROM THE MOUNTING WALL. 1127A.5.3.7.1 RECTANGULAR SEATS. THE REAR EDGE OF A RECTANGULAR SEAT SHALL BE 2-1/2 INCHES (64 MM) MAXIMUM FROM THE SEAT WALL THE FRONT EDGE OF A RECTANGULAR SEAT SHALL BE 15 INCHES (381 MM) MINIMUM AND 16 INCHES (406 MM) MAXIMUM FROM THE SEAT WALL. THE SIDE EDGE OF THE SEAT SHALL BE 1-1/2 INCHES (38 MM) MAXIMUM FROM THE ADJACENT WALL. 1127A.5.3.7.2 L-SHAPED SEATS. THE REAR EDGE OF AN L-SHAPED SEAT SHALL BE 2 1/ 2 INCHES (64 MM) MAXIMUM FROM THE SEAT WALL. THE FRONT EDGE OF AN L-SHAPED SEAT SHALL BE 15 INCHES (381 MM) MINIMUM AND 16 INCHES (406 MM) MAXIMUM FROM THE SEAT WALL. THE REAR EDGE OF THE "L" PORTION OF THE SEAT SHALL BE 1-1/2 INCHES (38 MM) MAXIMUM FROM THE WALL. THE FRONT EDGE SHALL BE 14 INCHES (356 MM) MINIMUM AND 15 INCHES (381 MM) MAXIMUM FROM THE WALL. THE END OF THE "L" SHALL BE 22 INCHES (559 MM) MINIMUM AND 23 INCHES (584 MM) MAXIMUM FROM THE MAIN SEAT WALL. 1127A.5.3.8 GRAB BARS. ACCESSIBLE SHOWER COMPARTMENTS SHALL BE PROVIDED WITH GRAB BARS, INSTALLED IN ACCORDANCE WITH SECTION 1127A.5.3.8.1 OR SECTION 1127 A.5.3.8.2. GRAB BARS SHALL ALSO COMPLY WITH SECTION 1127A.4 (see detail XX this sheet). WHEN MULTIPLE GRAB BARS ARE USED, REQUIRED HORIZONTAL GRAB BARS SHALL BE INSTALLED AT THE SAME HEIGHT ABOVE THE FINISH FLOOR. WHEN SEPARATE GRAB BARS ARE REQUIRED ON ADJACENT WALLS AT A COMMON MOUNTING HEIGHT, L-SHAPED OR U-SHAPED GRAB BARS MEETING THE DIMENSIONAL REQUIREMENTS OF SECTION 1127A.5.3.8.1 OR SECTION 1127A.5.3.8.2 SHALL BE PERMITTED. (SEE FIGURE 11A-9H OR FIGURE 11A-9I.) 1127A.5.3.8.1 STANDARD ROLL-IN SHOWER COMPARTMENTS. GRAB BARS SHALL BE INSTALLED ON THE BACK WALL AND ON THE SIDE WALL OPPOSITE THE SEAT. GRAB BARS ABOVE THE SEAT ARE NOT PERMITTED. GRAB BARS SHALL BE INSTALLED 6 INCHES (152 MM) MAXIMUM FROM ADJACENT WALLS. 1127A.5.3.8.2 ALTERNATE ROLL-IN SHOWER COMPARTMENTS. GRAB BARS SHALL BE INSTALLED ON THE BACK WALL AND THE SIDE WALL FARTHEST FROM THE COMPARTMENT ENTRY. GRAB BARS ABOVE THE SEAT ARE NOT PERMITTED. GRAB BARS SHALL BE INSTALLED 6 INCHES (152 MM) MAXIMUM FROM ADJACENT WALLS. 1127A.5.3.9 SOAP DISH. WHEN A SOAP DISH IS PROVIDED, IT SHALL BE LOCATED ON THE CONTROL WALL AT A MAXIMUM HEIGHT OF 40 INCHES (1016 MM) ABOVE THE SHOWER FLOOR, AND WITHIN THE REACH LIMITS FROM THE SEAT. 1127A.5.3.10 OPEN SHOWERS. WHEN NO SEPARATE SHOWER COMPARTMENTS ARE PROVIDED, THE SHOWER FOR PERSONS WITH DISABILITIES SHALL BE LOCATED IN A CORNER WITH L-SHAPED GRAB BARS EXTENDING ALONG TWO ADJACENT WALLS WITH A FOLDING SEAT ADJACENT TO THE SHOWER CONTROLS. (SEE FIGURE 11A-9I) 1127A.5.3.11 MULTIPLE SHOWERS. WHEN TWO OR MORE ACCESSIBLE SHOWERS ARE PROVIDED WITHIN THE SAME FUNCTIONAL AREA, THERE SHALL BE AT LEAST ONE SHOWER CONSTRUCTED OPPOSITE HAND FROM THE OTHER OR OTHERS (I.E., ONE LEFT-HAND CONTROL VERSUS RIGHT-HAND CONTROLS). 1/ 4 " MA X 1/ 4 " MA X 1/ 4 " MA X 1/ 2 " MA X (a) vertical change in level (b) beveled change in level 2 1 FIGURE 11A-1F CHANGE IN LEVEL FIGURE 11A-9E CLEAR FLOOR SPACE AT BATHTUBS (see figure 11A-9F for size of grab bars) (b) removable in-tub seat parallel approach (d) permanent seat parallel approach co n t r o l e n d wa l l back wall he a d e n d w a l l (a) removable in-tub seat forward approach (c) permanent seat forward approach 2' - 6 " M I N length of bathtub length of bathtub 2' - 6 " M I N 1'-0" MIN 4' - 0 " M I N length of bathtub 4' - 0 " M I N length of bathtub 1'-0" MIN co n t r o l e n d wa l l back wall he a d e n d wa l l co n t r o l e n d wa l l back wall he a d e n d w a l l co n t r o l e n d wa l l back wall he a d e n d wa l l FIGURE 11A-9F GRAB BARS AT BATHTUBS (a) Removable In-Tub Seat (b) Permanent Seat 17 " - 1 9 " 17 " - 1 9 " 15" - 16"15" - 16" 1'-3" MIN 1'-3" MIN 2'-0" MIN1'-0" MAX 2'-0" MAX 4'-0" MIN1'-0" MAX 1'-3" MAX ℄ control end (foot) wall back wall head end wall 1'-0" MIN ℄ control end (foot) wall 2'-0" MIN head end wallback wall 6' - 0 " 8" - 1 0 " 33 " - 3 6 " 8" - 1 0 " 33 " - 3 6 " 39 " - 4 1 " 4' - 0 " M A X 17 " - 1 9 " 5'-0" MIN CLEAR FINISH TO FINISH 33 " - 3 6 " 5'-0" MIN CLEAR FINISH TO FINISH 2' - 6 " M I N . 2' - 6 " M I N CL E A R FI N I S H TO F I N I S H 5'-0" MIN. ℄ 19" - 27" location of single lever controls 1/2" max beveled threshold top of mounting bracket 4' - 0 " top of mounting brackets 2'-0" MIN 6' - 0 " 4' - 0 " top of mounting brackets clear floor area 3'-6" MIN CLEAR FINISH TO FINISH 4' - 0 " M I N CL E A R FI N I S H T O F I N I S H 19" - 27" 1/2" max beveled threshold location of single lever controls FIGURE 11A-9H STANDARD ROLL-IN SHOWERS folding seat folding seat seat extension over 36" deep 3" MA X 3" MA X standard fixed showerhead on the opposite wall (a) 30" x 60" Roll-in Shower (b) 42" x 48" Roll-in Shower handheld showerhead shall have a diverter from fixed head 39 " - 4 1 " 17 " - 1 9 " 33 " - 3 6 " ℄ 4' - 0 " M A X FIGURE 11A-9I SHOWER SEATS AND GRAB BARS (b1) rectangular (b2) L - shaped 2 1 / 2 " MA X 1 1/2" MAX 15 " - 1 6 " seat wall 1 1/2" MAX seat wall 2 1 / 2 " MA X co m p a r t m e n t en t r y 15 " - 1 6 " 14" - 15" 22 " - 2 3 " 3" MAX co m p a r t m e n t en t r y 3" MAX back wall si d e w a l l si d e w a l l 6" 6" (a2) standard roll-in shower (b) shower seats compartment entry (a) grab bars (a1) alternate roll-in shower back wall si d e w a l l si d e w a l l front wall compartment entry 6" 6" 6" FIGURE 11A-9J OPEN SHOWER FIGURE 11A-9K ALTERNATE ROLL-IN SHOWER back wall si d e w a l l si d e w a l l front wall compartment entry 5'-0" MIN CLEAR FINISH TO FINISH 19 " - 2 7 " location of single lever controls 1/2" max beveled threshold folding seat 3' - 0 " M I N CL E A R FI N I S H TO F I N I S H 2'-0" MIN 3'-0" MIN 39 " - 4 1 " 4' - 0 " 17 " - 1 9 " 33 " - 3 6 " ℄ top of mounting bracket 2'-1" 35 " - 3 7 " 3' - 2 " 19" - 27" ℄ location of single lever controls folding seat 19" - 27" 2'-0" ℄ ℄ 6' - 0 " 36" grab bar 24" grab bar SEC. 1127A.10 ACCESSIBLE LAUNDRY ROOMS - 1127A.10 COMMON ACCESSIBLE LAUNDRY ROOMS 1127A.10.1 GENERAL. WHERE COMMON USE LAUNDRY ROOMS ARE PROVIDED, AT LEAST ONE OF EACH TYPE OF APPLIANCE PROVIDED IN EACH LAUNDRY AREA SHALL BE ACCESSIBLE, SHALL BE ON AN ACCESSIBLE ROUTE AND SHALL COMPLY WITH THIS SECTION. SUCH APPLIANCES INCLUDE CLOTHES WASHING MACHINES, DRYERS, SOAP DISPENSERS AND ANY RELATED FEATURES SUCH AS WASH SINKS, TABLES AND STORAGE AREAS. WHERE LAUNDRY ROOMS ARE PROVIDED ON FLOORS OF AN ELEVATOR BUILDING, EACH LAUNDRY ROOM SHALL BE ACCESSIBLE. WHERE THERE IS ONE LAUNDRY ROOM ON A GROUND FLOOR IN EACH BUILDING, EACH LAUNDRY ROOM SHALL BE ACCESSIBLE. WHERE THERE IS A LAUNDRY ROOM ON THE GROUND FLOOR OF A BUILDING AND ANOTHER LOCATED IN THE BASEMENT, IT IS ACCEPTABLE TO HAVE ONLY THE GROUND FLOOR LAUNDRY ROOM ACCESSIBLE. 1127A.10.2 CLEAR FLOOR SPACE. THERE SHALL BE A MINIMUM CLEAR SPACE 30 INCHES PERPENDICULAR BY 48 INCHES PARALLEL (762 MM BY 1219 MM) IN FRONT OF CLOTHES WASHERS AND DRYERS REQUIRED TO BE ACCESSIBLE. THERE SHALL BE A MINIMUM CLEAR SPACE 30 INCHES BY 48 INCHES (762 MM BY 1219 MM) PROVIDED FOR AT LEAST ONE OF EACH TYPE OF FIXTURE OR APPLIANCE PROVIDED IN THE LAUNDRY ROOM (E.G., SOAP DISPENSERS, WASH SINKS, TABLES, STORAGE AREAS). 1127A.10.3 CONTROLS AND OPERATING MECHANISMS. CLOTHES WASHERS AND DRYERS INCLUDING STACKED CLOTHES WASHERS AND DRYERS REQUIRED TO BE ACCESSIBLE SHALL HAVE CONTROLS AND OPERATING MECHANISMS (INCLUDING DOORS, COIN SLOTS, LINT SCREENS, DETERGENT AND BLEACH COMPARTMENTS) WITHIN THE REACH RANGE OF A SEATED USER. CONTROLS AND OPERATING MECHANISMS SHALL BE LOCATED NO HIGHER THAN 48 INCHES (1219 MM), AND NO LOWER THAN 15 INCHES (381 MM), ABOVE THE FINISHED FLOOR MEASURED TO THE CENTER OF THE GRIP. IF THE REACH IS OVER AN OBSTRUCTION (FOR EXAMPLE, WASHER OR DRYER), OPERATING MECHANISMS SHALL BE LOCATED WITHIN THE REACH RANGES SPECIFIED IN SECTION 1138A.3 (see detail XX / XXX). CONTROLS AND OPERATING MECHANISMS THAT DO NOT SATISFY THESE SPECIFICATIONS ARE ACCEPTABLE, PROVIDED THAT COMPARABLE MECHANISMS, CONTROLS OR OUTLETS THAT PERFORM THE SAME FUNCTIONS ARE PROVIDED WITHIN THE SAME AREA AND ARE ACCESSIBLE. CONTROLS AND OPERATING MECHANISMS SHALL BE OPERABLE WITH ONE HAND AND NOT REQUIRE TIGHT GRASPING, PINCHING OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO ACTIVATE CONTROLS AND OPERATING MECHANISMS SHALL BE NO GREATER THAN 5 POUNDS (22.2N). 1127A.10.4 WASHING MACHINES AND CLOTHES DRYERS. WASHING MACHINES AND CLOTHES DRYERS IN ACCESSIBLE COMMON USE LAUNDRY ROOMS SHALL BE FRONT LOADING. THE BOTTOM OF THE OPENING TO THE LAUNDRY COMPARTMENT SHALL BE LOCATED 15 INCHES ( 381 MM) MINIMUM AND 36 INCHES (914 MM) MAXIMUM ABOVE THE FINISH DOOR. HEIGHT OF FRONT LOADING LAUNDRY COMPARTMENT OPENING AND CONTROLS 15 " - 3 6 " 4' - 0 " M A X fr o n t m o u n t e d c o n t r o l s see 1138A.3 for obstructed high reach when controls are not front mounted CLEAR FLOOR AREA AT LAUNDRY EQUIPMENT 2'-0" MIN ℄2'-0" MIN 2' - 6 " M I N SEC. 1135A LAUNDRY ROOMS - SECTION 1135A LAUNDRY ROOMS 1135A.1 GENERAL. IF CLOTHES WASHING MACHINES AND CLOTHES DRYERS ARE PROVIDED IN COVERED MULTIFAMILY DWELLING UNITS, ONE OF EACH TYPE OF APPLIANCE SHALL BE PROVIDED. WHERE FRONT LOADING CLOTHES WASHERS ARE NOT PROVIDED, MANAGEMENT SHALL PROVIDE ASSISTIVE DEVICES, ON REQUEST OF THE OCCUPANT, TO PERMIT THE USE OF TOP-LOADING CLOTHES WASHERS. 12 3 4 4 A0.17 4 A0.17 4 A0.17