652 E Dyer Rd - Plan - Laserfiche WebLink

Metadata

Thumbnails

Annotations

Sheet No. Project Agency Plan Check / Permit No. Petersen Design Project No. Consultant 5082.1 652 East Dyer Road Santa Ana, CA 92705 DYER WAREHOUSE Staging & Set-Up Space Tenant Improvements Sheet Title Revision / Submittal History Scale Status . architecture + planning Agency Approval Petersen Design Architects, Inc. 333 El Camino Real #201, Tustin, CA 92780 M: 714.904.6720 E: mike@mpdarch.com www.mpdarch.com Architect's Stamp 10/31/25 Plan Check Submittal . N/A G-0.0 General Accessibility Notes & Details Comply with the accessibility requirements of CBC Chapter 11B and the Americans with Disabilities Act (ADA). Where CBC Chapter 11B and the ADA are at variance with each other in their requirements, comply with the more restrictive requirement that satisfies both codes. ACCESSIBLE ROUTES ACCESSIBLE ROUTES 1.At least one accessible route shall connect each story and mezzanine in multi-story buildings and facilities. 2.At least one accessible route shall connect accessible building or facility entrances with all accessible spaces and elements within the building or facility, including mezzanines, which are otherwise connected by a circulation path. 3.Accessible routes shall coincide with or be located in the same area as general circulation paths. Where circulation paths are interior, required accessible routes shall also be interior. An accessible route shall not pass through kitchens, storage rooms, restrooms, closets or other spaces used for similar purposes, except as permitted by Chapter 10. 4.Except at turns or passing spaces, the clear width of walking surfaces shall be 36 inches minimum. 5.Clear width for walking surfaces in corridors serving an occupant load of 10 or more shall be 44 inches minimum. 6.Clear width for aisles shall be 36 inches minimum if serving elements on only one side, and 44 inches minimum if serving elements on both sides. 7.Clear width for accessible routes to accessible toilet compartments shall be 44 inches except for door-opening widths and door swings. DOORS, DOORWAYS, AND GATES 1.Doors, doorways, and gates providing user passage shall be provided in accordance with 11B-206.5 Doors, Doorways, and Gates. 2.Doors, doorways and gates that are part of an accessible route shall comply with 11B-404 Doors, Doorways, and Gates. 3.Revolving doors, revolving gates, and turnstiles shall not be part of an accessible route. 4.At least one of the active leaves of doorways with two leaves shall comply with 11B-404.2.3 Clear Width and 11B-404.2.4 Maneuvering Clearances. 5.Door openings shall provide a clear width of 32 inches minimum. Clear openings of doorways with swinging doors shall be measured between the face of the door and the stop, with the door open 90 degrees. Openings more than 24 inches deep shall provide a clear opening of 36 inches minimum. There shall be no projections into the required clear opening width lower than 34 inches above the finish floor or ground. Projections into the clear opening width between 34 inches and 80 inches above the finish floor or ground shall not exceed 4 inches. 6.Minimum maneuvering clearances at doors and gates shall comply with 11B-404.2.4 Maneuvering Clearances. Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance. 7.Swinging doors and gates shall have maneuvering clearances complying with Table 11B-404.2.4.1. 8.Doorways less than 36 inches wide without doors or gates, sliding doors, or folding doors shall have maneuvering clearances complying with Table 11B-404.2.4.2. 9.Maneuvering clearances for forward approach shall be provided when any obstruction within 18 inches of the latch side an interior doorway, or within 24 inches of the latch side of an exterior doorway, projects more than 8 inches beyond the face of the door, measured perpendicular to the face of the door or gate. 10.Thresholds, if provided at doorways, shall be 1/2" inch high maximum. Raised thresholds and changes in level at doorways shall comply with 11B-302 Floor or Ground Surfaces and 11B-303 Changes in Level. 11.Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 11B-309.4 Operation. Operable parts of such hardware shall be 34 inches minimum and 44 inches maximum above the finish floor or ground. Where sliding doors are in the fully open position, operating hardware shall be exposed and usable from both sides. 12.Force for pushing or pulling open a door or gate other than fire doors shall be as follows: a.Interior hinged doors and gates: 5 pounds maximum. b.Sliding or folding doors: 5 pounds maximum. c.Required fire doors: the minimum opening force allowable by the appropriate administrative authority, not to exceed 15 pounds. d.Exterior hinged doors: 5 pounds maximum. 13.Swinging door and gate surfaces within 10 inches of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door or gate. Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch of the same plane as the other and be free of sharp or abrasive edges. Cavities created by added kick plates shall be capped. FLOOR OR GROUND SURFACES 1.Floor and ground surfaces shall be stable, firm, and slip resistant. 2.Carpet or carpet tile shall be securely attached and shall have a firm cushion, pad, or backing or no cushion or pad. Carpet or carpet tile shall have a level loop, textured loop, level cut pile, or level cut/ uncut pile texture. Pile height shall be 1/4 inch maximum. CHANGES IN LEVEL 1.Vertical changes in level for floor or ground surfaces may be 1/4 inch high maximum and without edge treatment. Changes in level greater than 1/4 inch and not exceeding 1/2 inch in height shall be beveled with a slope not steeper than 1:2. 2.Changes in level greater than 1/2 inch in height shall be ramped and shall comply with the requirements of 11B-405 Ramps or 11B-406 Curb Ramps as applicable. 3.Abrupt changes in level exceeding 4 inches in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning curbs at least 6 inches in height above the walk or sidewalk surface or by guards or handrails with a guide rail centered 2 inches minimum and 4 inches maximum above the surface of the walk or sidewalk. These requirements do not apply between a walk or sidewalk and an adjacent street or driveway. TURNING SPACE 1.Circular turning spaces shall be a space of 60 inches diameter minimum and may include knee and toe clearance complying with 11B-306 Knee and Toe Clearance. 2.T-Shaped turning spaces shall be a T-shaped space within a 60 inch square minimum with arms and base 36 inches wide minimum. Each arm of the T shall be clear of obstructions 12 inches minimum in §11B-304.3.2, each direction and the base shall be clear of obstructions 24 inches minimum. KNEE AND TOE CLEARANCE 1.For lavatories and built-in dining and work surfaces required to be accessible, toe clearance shall be provided that is 30 inches in width and 9 inches in height above the finish floor or ground for a depth of 19 inches minimum. 2.Toe clearance shall extend 19 inches maximum under lavatories for toilet and bathing facilities and 25 inches maximum under other elements. 3.At lavatories in toilet and bathing facilities, knee clearance shall be provided that is 30 inches in width for a depth of 11 inches at 9 inches above the finish floor or ground and for a depth of 8 inches at 27 inches above the finish floor or ground increasing to 29 inches high minimum above the finish floor or ground at the front edge of a counter with a built-in lavatory or at the front edge of a wall-mounted lavatory fixture. 4.At dining and work surfaces required to be accessible, knee clearance shall be provided that is 30 inches in width at 27 inches above the finish floor or ground for a depth of at least 19 inches. PROTRUDING OBJECTS 1.Except for handrails, objects with leading edges more than 27 inches and less than 80 inches above the finish floor or ground shall protrude no more than 4 inches horizontally into the circulation path. Handrails may protrude 4'/ inches maximum. 2.Freestanding objects mounted on posts or pylons shall overhang circulation paths no more than 12 inches when located from 27 to 80 inches above the finish floor or ground. 3.Protruding objects shall not reduce the clear width required for accessible routes. 4.Lowest edge of a sign or other obstruction, when mounted between posts or pylons separated with a clear distance greater than 12 inches, shall be less than 27 inches or more than 80 inches above the finish floor or ground. 5.Vertical clearance shall be at least 80 inches high on circulation paths except at door closers and door stops, which may be 78 inches minimum above the finish floor or ground. 6.Guardrails or other barriers with a leading edge located 27 inches maximum above the finish floor or ground shall be provided where the vertical clearance on circulation paths is less than 80 inches high. REACH RANGES 1.Electrical controls and switches intended to be used by the occupant of a room or area to control lighting and receptacle outlets, appliances or cooling, heating and ventilating equipment shall be located within allowable reach ranges. Low reach shall be measured to the bottom of the outlet box and high reach shall be measured to the top of the outlet box. 2.Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles shall be located within allowable reach ranges. Low reach shall be measured to the bottom of the outlet box and high reach shall be measured to the top of the outlet box. 3.High forward reach that is unobstructed shall be 48 inches maximum and the low forward reach shall be 15 inches minimum above the finish floor or ground. 4.High forward reach shall be 48 inches maximum where the reach depth is 20 inches or less and 44 inches maximum where the reach depth exceeds 20 inches. High forward reach shall not exceed 25 inches in depth. 5.High side reach shall be 48 inches maximum and the low side reach shall be 15 inches minimum above the finish floor where the side reach is unobstructed or the depth of any obstruction does not exceed 10 inches. 6.High side reach shall be 46 inches maximum above the finish floor or ground where the high side reach is over an obstruction more than 10 inches but not more than 24 inches in depth. 7.Obstructions for high side reach shall not exceed 34 inches in height and 24 inches in depth. OPERABLE PARTS 1.Operable parts shall be operable with one hand and shall not require tight grasping, pinching, twisting of the wrist. Force required to activate operable parts shall be 5 pounds maximum. GENERAL ACCESSIBILITY NOTES SITE PATH OF TRAVEL AND PARKING (cont.) CURB RAMPS 1.Running slope of the parallel curb ramp segments shall be in-line with the direction of sidewalk travel. Ramp runs shall have a running slope not steeper than 1:12 (8.33%). 2.A turning space 48 inches minimum by 48 inches minimum shall be provided at the bottom of the parallel curb ramp. The slope of the turning space in all directions shall be 1:48 maximum (2.083%). 3.Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles. Curb ramps at marked crossings shall be wholly contained within the markings, excluding any flared sides. 4.Clear width of curb ramp runs shall be 48 inches minimum. 5.Grade breaks at the top and bottom of curb ramp runs shall be perpendicular to the direction of the ramp run. Grade breaks shall not be permitted on the surface of ramp runs and turning spaces. Surface slopes that meet at grade breaks shall be flush. 6.Cross slope of curb ramps shall be 1:48 (2.083%) maximum. 7.Counter slopes of adjoining gutters and road surfaces immediately adjacent to and within 24 inches of the curb ramp shall not be steeper than 1:20 (5%). The adjacent surfaces at transitions at curb ramps to walks, gutters, and streets shall be at the same level. 8.Curb ramps shall have detectable warnings complying with 11B-705 Detectable Warnings. PARKING SPACES 1.Where parking spaces are provided, accessible parking spaces shall be provided in number and kind required per Section 11B-208 Parking Spaces. 2.One in every six or fraction of six parking spaces required by Section 11B-208.2 Minimum Number, but not less than one, shall be served by an access aisle 96 inches wide minimum placed on the side opposite the driver's side when the vehicle is going forward into the parking space and shall be designated "van accessible". All such spaces may be grouped on one level of a parking structure. 3.Accessible parking spaces complying with Section 11B-502 Parking Spaces serving a particular building or facility shall be located on the shortest accessible route of travel from adjacent parking to an accessible entrance (as near as practical to an accessible entrance). 4.In buildings with multiple accessible entrances with adjacent parking, accessible parking spaces complying with Section 11B-502 Parking Spaces shall be dispersed and located closest to the accessible entrances. 5.Car and van accessible parking space(s) and access aisle(s) shall be at least 18 feet in length. 6.Accessible car parking spaces shall be at least 9 feet in width. 7.Van stall access aisle shall be 8 foot wide minimum and shall adjoin an accessible route. Two parking spaces shall be permitted to share a common access aisle. 8.Car stall access aisle shall be 5 foot wide minimum and shall adjoin an accessible route. Two parking spaces shall be permitted to share a common access aisle. 9.Access aisles shall be marked with a blue painted borderline around their perimeter. The area within the blue borderlines shall be marked with hatched lines a maximum of 36 inches on center in a color contrasting with that of the aisle surface, preferably blue or white. The words "NO PARKING" shall be painted on the surface within each access aisle in white letters a minimum of 12 inches in height and located to be visible from the adjacent vehicular way. Access aisle markings may extend beyond the minimum required length. 10.Access aisles shall not overlap the vehicular way. Access aisles shall be permitted to be placed on either side of the parking space except for van parking spaces which shall have access aisles located on the passenger side of the parking spaces. 11.Parking space identification signs shall include the International Symbol of Accessibility complying with Section 11B-703.7.2.1 International Symbol of Accessibility. 12.Signs identifying van parking spaces shall contain additional language or an additional sign with the designation "van accessible." Signs shall be 60 inches minimum above the finish floor or ground surface measured to the bottom of the sign. 13.Parking identification signs shall be reflectorized with a minimum area of 70 square inches. 14.Additional language or an additional sign below the International Symbol of Accessibility shall state "Minimum Fine $250." 15.A parking space identification sign shall be visible from each parking space. Signs shall be permanently posted either immediately adjacent to the parking space or within the projected parking space width at the head end of the parking space. Signs may also be permanently posted on a wall at the interior end of the parking space. 16.Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2. 17.An additional sign complying with Section 11B-502.8 shall be posted either; 1) in a conspicuous place at each entrance to an off-street parking facility or 2) immediately adjacent to on-site accessible parking and visible from each parking space. 18.Signs intended for use by pedestrians within parking facilities, including directional or informational signs indicating parking sections or levels, shall comply with the requirements of Section 11B-216. 19.Parking spaces and access aisles shall be designed so that persons using them are not required to travel behind parking spaces other than to pass behind the parking space in which they parked. 20.A curb or wheel stop shall be provided if required to prevent encroachment of vehicles over the required clear width of adjacent accessible routes. STAIRWAYS 1.All steps on a flight of stairs shall have uniform riser heights and uniform tread depths. Risers shall be 4 inches high minimum and 7 inches high maximum.Ttreads shall be 11 inches deep minimum. Open risers are not permitted. Treads shall be permitted to have a slope not steeper than 1:48. Interior stairs shall have the upper approach and lower tread marked by a stripe providing clear visual contrast. Exterior stairs shall have the upper approach and all treads marked by a stripe providing clear visual contrast. The strip shall be a minimum of 2 inches wide to a maximum of 4 inches wide placed parallel to, and not more than 1 inch from, the nose of the step or upper approach. The stripe shall extend the full width of the step or upper approach and shall be of material that is at least as slip resistant as the other treads of the stair. A painted stripe shall be acceptable. Grooves shall not be used to satisfy this requirement. HANDRAILS 1.Handrails shall comply with 11B-505. Top of gripping surfaces for handrails shall be 34 inches minimum and 38 inches maximum vertically above walking surfaces, stair nosings, and ramp surfaces. Handrails shall be at a consistent height above walking surfaces, stair nosings, and ramp surfaces. The clearance between handrail gripping surfaces and adjacent surfaces shall be 1 ½" minimum. PLUMBING FIXTURES DRINKING FOUNTAINS 1.No fewer than two drinking fountains shall be provided. When provided, one drinking fountain shall comply with 11B-602.1 through 11B-602.6, 11B-602.8 and 11B-602.9 and one drinking fountain shall comply with 11B-602.7 and 11B-602.9. TOILET ROOM CLEARANCES 1.Where toilet rooms are provided, each toilet room shall comply with 11B-603 Toilet and Bathing Rooms. 2.Unisex toilet rooms shall contain not more than one lavatory, and not more than two water closets without urinals or one water closet and one urinal. Doors to unisex toilet rooms shall have privacy latches. 3.Door shall not swing into the clear floor space or clearance required for any fixture. Other than the door to the accessible water closet compartment, a door in any position may encroach into the turning space by 12 inches maximum. 4.At single user toilet rooms, doors shall be permitted to swing into the clear floor space or clearance required for any fixture only if a 30 inch by 48-inch minimum clear floor space is provided within the room beyond the arc of the door swing. 5.Mirrors located above the lavatories or countertops shall be installed within the bottom edge of the reflecting surface 40 inches maximum above the finish floor or ground. Mirrors not located above the lavatories or countertops shall be installed with the bottom edge of the reflecting surface 35 inches maximum above the finish floor or ground. 6.Coat hooks shall be located within one of the reach ranges specified in Section 11B-308. Shelves shall be located 40 inches minimum and 48 inches maximum above the finish floor. Medicine cabinets shall be located with a usable shelf no higher than 44 inches maximum above the finish floor. 7.Where towel or sanitary napkin dispensers, waste receptacles, or other accessories are provided in toilet facilities, at least one of each type shall be located on an accessible route. All operable parts, including coin slots, shall be 40 inches maximum above the finish floor. Baby changing stations are not required to comply with Section 11B-603.5 (See exception) WATER CLOSETS AND TOILET COMPARTMENTS 1.Where toilet compartments are provided, at least 5 percent but no less than one toilet compartment shall comply with Section 11B-604.8.1. 2.Where water closets are provided, at least 5 percent but no less than one shall comply with Section 11B-604. 3.Water closet shall be positioned with a wall or partition to the rear and to one side. Centerline of the water closet shall be 17 inches minimum to 18 inches maximum from the side wall or partition, except that the water closet shall be 17 inches minimum and 19 inches maximum from the side wall or partition in the ambulatory accessible toilet compartment specified in Section 11B-604.8.2 Ambulatory Accessible Compartments. Water closets shall be arranged for a left-hand or right-hand approach. 4.Clearance around a water closet shall be 60 inches minimum measured perpendicular from the sidewall and 56 inches minimum measured perpendicular from the rear wall. A minimum 60 inches wide and 48 inches deep maneuvering space shall be provided in front of the water closet. 5.Seat height of a water closet above the finish floor shall be 17 inches minimum and 19 inches maximum measured to the top of the seat. Seats shall not be sprung to return to a lifted position. Seats shall be 2 inches high maximum. 6.Sidewall grab bars shall be 42 inches long minimum, located 12 inches maximum from the rear wall and extending 54 inches minimum from the rear wall with the front end positioned 24 inches minimum in front of the water closet. 7.Rear grab bar shall be 36 inches long minimum and extend from the centerline of the water closet 12 inches minimum on one side and 24 inches minimum on the other side. 8.Flush controls shall be hand operated or automatic. Hand operated flush controls shall comply with Section 11B-309.4 Operation except they shall be located 44 inches maximum above the floor. Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with Section 11B-604.8.2 Ambulatory Accessible Compartments. 9.Toilet paper dispensers shall comply with Section 11B-309.4 Operation and shall be 7 inches minimum and 9 inches maximum in front of the water closet measured to the centerline of the dispenser. The outlet of the dispenser shall be below the grab bar, 19 inches minimum above the finish floor and shall not be located behind the grab bars. Dispensers shall not be of a type that control delivery or that does not allow continuous paper flow. 10.Wheelchair accessible toilet compartments shall meet the requirements of Sections 11B-604.8.1 Wheelchair Accessible Compartments and 11B-604.8.3 Coat Hooks and Shelves. Compartments containing more than one plumbing fixture shall comply with Section 11B-603 Toilet and Bathing Rooms. Ambulatory accessible compartments shall comply with Sections 11B-604.8.2 Ambulatory Accessible Compartments and 11B-604.8.3 Coat Hooks and Shelves. 11.Toilet compartment doors, including door hardware, shall comply with Section 11B-404 Doors, Doorways, and Gates except that if the approach is from the push side of the compartment door, clearance between the door side of the compartment and any obstruction shall be 48 inches minimum measured perpendicular to the compartment door in its closed position. Door shall be located in front partition or in the side wall or partition farthest from the water closet. 12.At least one side partition shall provide a toe clearance of 9 inches minimum above the finish floor and 6 inches deep minimum beyond the compartment-side face of the partition, exclusive of partition support members. Partition components at toe clearances shall be smooth without sharp edges or abrasive surfaces. Compartments for children's use shall provide a toe clearance of 12 inches minimum above the finish floor. 13.Ambulatory accessible compartments shall have a depth of 35 inches minimum and 37 inches maximum. 14.Where urinals are provided, at least 10 percent but no less than one shall comply with Section 11B-605. 15.Urinals shall be the stall-type or the wall-hung type with the rim 17 inches maximum above the finish floor or ground. Urinals shall be 13 1/2 inches deep minimum measured from the outer face of the urinal rim to the back of the fixture. 16.Where lavatories are provided, at least 10 percent but no less than one shall comply with Section 11B-606 and shall not be located in a toilet compartment. 17.For lavatories and sinks, a clear floor space complying with Section 11B-305 Clear Floor or Ground Surfaces, positioned for a forward approach, and knee and toe clearance complying with Section 11B-306 Knee and Toe Clearance shall be provided. 18.Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches maximum above the finish floor or ground. SIGNS AND IDENTIFICATION SIGNS AND IDENTIFICATION 1.Except building directories, menus, seat and row designations in assembly areas, occupant names, building addresses, and company names and logos, new or altered signs shall be provided in accordance with 11B-216 Signs and shall comply with 11B-703 Signs. The addition of or replacement of signs shall not trigger any additional path of travel requirements. 2.Interior and exterior signs identifying permanent rooms and spaces shall comply with 11B-703.1 General, 11B-703.2 Raised Characters, 11B-703.3 Braille and 11B-703.5 Visual Characters. Where pictograms are provided as designations of permanent interior rooms and spaces, the pictograms shall comply with 11B-703.6 Pictograms and shall have text descriptors complying with 11B-703.2 and 11B-703.5. 3.Signs that provide direction to or information about interior and exterior spaces and facilities of the site shall comply with 11B-703.5 Visual Characters. 4.Signs for means of egress shall comply with 11B-216.4 Means of Egress. 5.Signs identifying parking spaces and signs within parking facilities shall comply with Section 11B 216.5. 6.In existing buildings and facilities where not all entrances comply with 11B-404 Doors, Doorways, and Gates, compliant entrances shall be identified by the International Symbol of Accessibility (ISA complying with 11B-703.7.2.1 ISA. Directional signs complying with 11B-703.5 Visual Characters that indicate the location of the nearest entrance complying with 11B-404 shall be provided at entrances that do not comply with 11B-404 Doors, Doorways, and Gates. Directional signs complying with 11B 703.5 Visual Characters, including the ISA complying with 11B-703.7.2.1 ISA, indicating the accessible route to the nearest accessible entrance shall be provided at junctions when the accessible route diverges from the regular circulation path. SITE PATH OF TRAVEL AND PARKING ALTERATIONS 1.When alterations or additions are made to existing buildings or facilities, an accessible path of travel to the specific area of alteration or addition shall be provided unless otherwise exempt. 2.Primary accessible path of travel shall include a primary entrance to the building or facility; toilet and bathing facilities serving the area; drinking fountains serving the area; public telephones serving the area, and signs. ACCESSIBLE ROUTES 1.At least one accessible route shall be provided within the site from accessible parking spaces and accessible passenger loading zones; public streets and sidewalks; and public transportation stops to the accessible building or facility entrance they serve. Where more than one route is provided, all routes must be accessible. 2.At least one accessible route shall connect accessible buildings, accessible facilities, accessible elements, and accessible spaces that are on the same site. 3.Accessible routes shall consist of one or more of the following components: walking surfaces with a running slope not steeper than 1:20 (5%), doorways, ramps, curb ramps excluding the flared sides, elevators, and platform lifts. 4.Running slope of walking surfaces shall not be steeper than 1:20 (5%). Cross slope of walking surfaces shall not be steeper than 1:48 (2.083%). 5.Clear width for sidewalks and walks shall be 48 inches minimum. ENTRANCES 1.Entrances shall be provided in accordance with 11B-206.4 Entrances. Entrance doors, doorways, and gates shall comply with 11B-404 Doors, Doorways, and Gates and shall be on an accessible route complying with 11B-402 Accessible Routes; (See exceptions). 2.All entrances and exterior ground-floor exits to buildings and facilities shall comply with 11B-404 Doors, Doorways, and Gates. DETECTABLE WARNINGS 1.Curb ramps shall have detectable warnings that extend 36 inches in the direction of travel for the full width of the ramp run less than 2 inches maximum on each side, excluding any flared sides. 2.On parallel curb ramps, detectable warnings shall be placed on the turning space at the flush transition between the street and sidewalk. Detectable warnings shall extend the full width of the turning space at the flush transition between the parking facility and the sidewalk less than 2 inches maximum on each side 3.Walks that cross or adjoin a route provided for vehicular traffic, such as in a street, driveway, or parking facility, shall be separated by detectable warnings, curbs, railings or other elements between the pedestrian areas and vehicular areas. 4.Detectable warnings provided to separate walks that cross or adjoin a route provided for vehicular traffic, such as in a street, driveway, or parking facility, shall be 36 inches in width and continuous at the boundary between the pedestrian areas and vehicular areas. 5.Detectable warning surfaces shall be yellow and approximate FS 33538 of Federal Standard 595C and meet the dimensional and property requirements of 11B-705.1. 6.Detectable warning surfaces shall provide a 70 percent minimum visual contrast with adjacent walking surfaces. Contrast in percent shall be determined per 11B-705.1.1.3.2 (See exception). RAMPS 1.Ramp runs shall have a running slope not steeper than 1:12. cross slope on ramp runs shall not be steeper than 1:48. the clear width of a ramp run shall be 48"minimum. Handrails may project into the required width of the ramp at each side 3 ½ inches maximum at the handrail height. The rise for any ramp run shall be 30 inches maximum. Ramps shall have handrails complying with 11B-505. Edge protection complying with 11B-405.9.2 shall be provided on each side of ramp runs and at each side of ramp landing. TEXT TEXT 305 EXAM EXIT 5" 3/ 8 " 1" 4" A. SERVICE / EXIT / ETC.B. EXAM / OFFICES / ETC.60 " 234 234 LITERARY BRAILLE STANDARD DIMENSIONS BRAILLE SIGNAGETYPICAL ROOM/EXIT SIGNAGE STANDARD TACTILE & EGRESS (PLAN VIEW) SIGNAGE MOUNTINGA CORRESPONDING GRADE II BRAILLE DOT DIAMETER .059 INCHES INTER-DOT SPACING .090 INCHES HORIZONTAL SEPARATION BETWEEN CELLS .241 INCHES VERTICAL SEPARATION BETWEEN CELLS .395 INCHES PERMANENT SIGNAGE TO BE INSTALLED ON THE WALL ADJACENT TO THE LATCH SIDE OF THE DOOR. MOUNTING LOCATION MUST ALLOW A PERSON TO APPROACH WITHOUT ENCOUNTERING PROTRUDING OBJECTS OR STANDING WITHIN THE SWING PATH OF THE DOOR. LETTERS AND NUMERALS SHALL BE RAISED 1/32", UPPER CASE, SANS SERIF OR SIMPLE SERIF TYPE AND SHALL BE ACCOMPANIED WITH GRADE II BRAILLE, RAISED CHARACTERS SHALL BE AT LEAST 5/8" HIGH, BUT NO HIGHER THAN 2" BACKGROUND 70% CONTRAST 1"HELVETICA RM NUMBER RAISED 1/32" WINDOW FOR 5/8" HELVETICA ROOM NAME LETTER. EXIT DOORS NOTES:. THIS IS IN ADDITION TO OVERHEAD/LOW-LEVEL ILLUMINATED SIGNS DOOR SWING PATH 8"8" 3/ 8 " 2" M I N . CLEAR FLOOR SPACE CENTERED ON TACTILE CHARACTERS BEYOND THE AREA OF DOOR SWING. 45 ° 18 " M I N CL 60 " T O T O P O F S I G N 9" MIN. @ OUTSWINGING DOORS ONLY PERMANENT SIGNAGE TO BE INSTALLED ON THE WALL ADJACENT TO THE LATCH SIDE OF THE DOOR. MOUNTING LOCATION MUST ALLOW A CLEAR FLOOR SPACE OF 18" MIN. BY 18" MIN., CENTERED ON THE TACTILE CHARACTERS, IS PROVIDED BEYOND THE ARC OF ANY DOOR SWING BETWEEN THE CLOSED POSITION AND 45 DEGREE OPEN POSITION. (PER CBC 11B-703.4.2) 48" MINIMUM AFF TO THE BASELINE OF THE LOWEST LINE OF BRAILLE AND 60" MAXIMUM AFF TO THE BASELINE OF THE HIGHEST TACTILE CHARACTER. 59 " T O C E N T E R L I N E O F S I G N O N D O O R EQ EQ CL SEE MOUNTING DETAIL B 18" MIN. 9" MIN. CL STANDARD TACTILE & EGRESS (ELEVATION VIEW) SIGNAGE MOUNTINGB RESTROOM SIGNAGE MOUNTINGC 10 ACCESSIBLE INTERIOR SIGNAGE SCALE: 1/2" = 1'-0" 60 " M I N 24" MIN EXTERIOR 18" MIN INTERIOR 4' - 0 " M I N 36" MIN 60 " M I N 4' - 0" MIN FRONT APPROACH HA S B O T H C L O S E R A N D L A T C H 44 " M I N ( 4 8 " M I N I F D O O R 22" MIN CLOSER AND A LATCH 12" IF DOOR HAS BOTH A HINGE APPROACH 24" MIN 60 " M I N HA S C L O S E R ) 44 " M I N ( 4 8 " M I N I F D O O R PUSH APPROACH 24" MIN DOORS IN PARALLEL 48" MIN 4'-0" min X > 8 " X > 8 " X > 8 " 13 DOOR CLEARANCES SCALE: 1/4" = 1'-0" 30"x48" WHEELCHAIR CLEARANCE 30" 48 " EQ EQ CL 30" 48 " EQ EQ X" CL (S E E F L O O R P L A N F O R L O C A T I O N S ) 60 " A T A L C O V E C O N D I T I O N X" (S E E F L O O R P L A N F O R L O C A T I O N S ) 60 " A T A L C O V E C O N D I T I O N (18" MIN) 18" U.N.O. CLEARANCE REQUIREMENTS FOR ALL ACCESSIBLE SINKS (19" - 25") X = 19" 10" MIN KNEE CLEARANCE 27 " M I N 9" TOE CLEARANCE 29 " M I N 10" MIN 13"6" MAX (19" - 25") X = 19" KNEE CLEARANCE TOE CLEARANCE 27 " M I N 1 6 13"6" MAX 1 6 9" ACCESSIBLE REACH RANGE ACCESSIBLE REACH RANGE ACCESSIBLE SINK WALL MOUNT COUNTER MOUNT 5 3/4" (3 4 " M A X I M U M ) 33 3 / 4 " T O R I M O F S I N K (3 4 " M A X I M U M ) 33 3 / 4 " T O R I M O F S I N K 05 ACCESSIBLE SINK MOUNTING SCALE: 1/2" = 1'-0" FINISH FLOOR FINISH FLOOR CARPET PER CBC 11B-302.2 2 1 1:2 SLOPE MAX 1:2 SLOPE MAX 2 1 DOOR 1/ 4 " M A X 1/ 2 " M A X 1/ 4 " M A X 1/ 4 " M A X . 1/ 2 " M A X 1/ 4 " M A X 1/ 4 " M A X 1/ 2 " M A X 08 THRESHOLDS SCALE: 3" = 1'-0" 03 ENTRY THRESHOLD NO SCALE 20 4' - 0" 1' - 3 " M I N 4' - 0 " RA N G E FO W A R D R E A C H 1' - 3 " 4' - 0 " M A X RA N G E SI D E R E A C H MAX. SIDE REACH OVER AN OBSTRUCTION (SEE 11B-308.3.2) NOTE: MAXIMUM DEPTH OF OBSTRUCTION ALLOWED IS 25". WHEN DEPTH OF OBSTRUCTION IS MORE THAN 20" AND 25" MAX, THE MAXIMUM FORWARD REACH HEIGHT FROM THE FLOOR SURFACE IS 44". WHEN DEPTH OF OBSTRUCTION IS 20" MAX, THE MAXIMUM FORWARD REACH HEIGHT FROM THE FLOOR SURFACE IS 48" X=DEPTH OF OBSTRUCTION Y=MAXIMUM REACH HEIGHT Z=MIN. CLEAR SPACE BELOW OBSTRUCTION Y Z X A 34 " M A X B SIDE REACH RANGE FORWARD REACH RANGE OBSTRUCTION 10" MAX NOTE: "B" IS 48" MAX. WHEN "A" IS 10" MAX. "B" IS 46" MAX. WHEN "A" IS MORE THAN 10" AND 24" MAX. REACH RANGES SCALE: 1/4" = 1'-0" TO H I G H E S T O P E R A B L E P A R T 40 " M A X . (4 0 " M A X . T O T O P O F O P E N I N G ) 30 " T O T O P TO T O P O F O P E N I N G 40 " M A X . SEAT COVER DISPENSER SOAP DISPENSER NAPKIN/ TAMPON DISPOSAL SMALL PAPER TOWEL DISPENSER SPECIMEN PASS THRU 24" VERTICAL GRAB BAR TO B O T T O M O F B A R 36 " 48 " T O T O P O F C A B I N E T FIRE EXTINGUISHER CABINET (F.E.C.) OF R E F L E C T I N G S U R F A C E 40 " M A X . T O B O T T O M E D G E MIRROR ABOVE LAVATORY OR COUNTER (4 0 " M A X . T O T O P O F O P E N I N G ) 30 " T O T O P TO T O P O F H A N D L E 48 " M A X . TO H I G H E S T O P E R A B L E P A R T 40 " M A X . HAND SANITIZER DISPENSER GLOVE BOX HOLDER SHARPS CONTAINER 1' - 3" CL CL MAKE SURE THERE IS A CLEAR AREA TO THE SIDE OF THE GLOVE BOX FOR RESTOCKING 56 " M A X . T O T O P NOTE:SEE INTERIOR ELEVATIONS FOR LOCATION. INSTALL GLOVE BOX & SHARPS CONTAINER ABOVE CART OR COUNTER AS SHOWN TO AVOID THEM BEING PROTRUDING OBJECTS. SHARPS CONTAINER & GLOVE BOX HOLDER 25 ACCESSIBLE STANDARD MOUNTING (WHERE OCCURS) SCALE: 1/2" = 1'-0"