1700 E Santa Clara Ave - Plan - Laserfiche WebLink

Home Browse Search

GRAB BARS 1. Grab bars with circular section shall have an outside diameter of 1¼ inches minimum and 2 inches maximum. Grab bars with non-circular cross section shall have a cross-section dimension of 2 inches maximum and a perimeter dimension of 4 inches minimum and 4.8 inches maximum. [11B-609.2] 2. The space between the wall and the grab bar shall be 1½ inches. The space between the grab bar and projecting objects below and at the ends shall be 1½ inches minimum. The space between the grab bar and projecting above shall be 12 inches minimum. The space between the grab bars and shower controls, shower fittings, and other grab bars above shall be permitted to be 1½ inches minimum. 3. Grab bars shall be installed in a horizontal position, 33 inches minimum and 36 inches maximum above the finish floor measured to the top of the gripping surface. 4. Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges. [11B-609.5] 5. Grab bars shall not rotate within their fittings. [11B-609.6] 6. Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds is applied at any point on the grab, fastener, mounting device, or supporting structure. [11B-609.8] DIVISION 7: COMMUNICATION ELEMENTS AND FEATURES SIGNS 1. Raised characters shall comply with 11B-703.2 Raised characters and shall be duplicated in Braille complying with 11B-703.3 Braille. Raised characters shall be installed in accordance with 11B-703.4 Installation Height and Location. §11B-703.2 a. Raised characters shall be 1/32" minimum above their background. §11B-703.2.1 b. Characters shall be uppercase. §11B-703.2.2 c. Characters shall be sans serif. Characters shall not be italic, oblique, script, highly decorative, or of other unusual forms. §11B-703.2.3 d. Characters shall be selected from fonts where the width of the uppercase letter "O" is 55 60 percent minimum and 110 percent maximum of the height of the uppercase letter "I". § 11B-703.2.4 e. Characters height measured vertically from the baseline of the character shall be 5/8” minimum and 2”maximum based on the height of the uppercase letter “I”. §11B-703.2.5 f. Stroke thickness of the uppercase letter “I”shall be 15 percent maximum of the height of the character. §11B-703.2.6 g. Character spacing shall be measured between the two closest points of adjacent raised characters within a message, excluding word spaces. Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8”minimum and 4 times the raised characters stroke width maximum. Where characters have other cross sections, spacing between individual raised characters shall be 1/16”minimum and 4 times the raised characters stroke width maximum at the base of the cross section, and 1/8”inch minimum and 4 times the raised character stroke width maximum at the top of the cross sections. Characters shall be separated from raised borders and decorative elements 3/8” minimum.§11B-703.2.7 h. Spacing between the baselines of separate lines of raised characters within a message shall be 135 percent minim and 170 percent maximum of the raised character height. § 11B-703.2.8 i. Text shall be in a horizontal format.§11B-703.2.9 2. Braille shall be contracted (Grade 2) and shall comply with 11B-703.3 Braille and 11B-703.4 Installation Height and Location.§11B-703.3 a. Braille dots shall have a domed or rounded shape and shall comply with Table 11B-703.3.1 The indication of an uppercase letter or letters shall only be used before the first word of sentences, proper nouns and names, individual letters of the alphabet, initials, and acronyms.§11B-703.3.1 b. Braille shall be positioned below the corresponding text in a horizontal format, flush left or centered. If text is multi-lined, Braille shall be placed below the entire text. Braille shall be separated 3/8”minimum and ½”maximum from any other tactile characters and 3/8” minimum from raised borders and decorative elements.§11B-703.3.2 3. Signs with tactile characters shall comply with 11B-703.4 Installation Height and Location.§ 11B-703.4 a. Tactile characters on signs shall be located 48 inches minimum above finish floor or ground surface, measured from baseline of the lowest tactile character Braille cells and 60 inches maximum above finish floor or ground surface, measured from the baseline of the highest tactile character line of raised characters.§11B703.4.1 (See exception) b. Where a tactile sign is provided at a door, the sign shall be located alongside the door at the latch side. Where a tactile sign is provided at double doors with one active leaf, the sign shall be located on the inactive leaf. Where a tactile sign is provided at double doors with two active leafs, the sign shall be located to the right of the right hand door Where there is no wall space at the latch side of a single door or at the right side of double doors, signs shall be located on the nearest adjacent wall. Signs containing tactile characters shall be located so that a clear floor space of 18 inches minimum by 18 inches minimum, centered on the tactile character, is provided beyond the arc of any door swing between the closed position and 45 degree open position. Where permanent identification signage is provided for rooms and spaces they shall be located on the approach side of the door as one enters the room or space. Signs that identify exits shall be located on the approach side of the door as one exits the room or space. 11B-703.4.2 (See exception) 4. Visual characters shall comply with the following, except where visual characters comply with 11B-703.2 Raised Characters and are accompanied by Braille complying with 11B-703.3 Braille, they shall not be required to comply with 11B-703.5.2 through 11B-703.5.6, 11B-703.5.8 and 11B-703.5.9: a. Characters and their background shall have a non-glare finish. Characters shall contrast with their background with either light characters on a dark background or dark characters on a light background. §11B-703.5.1 b. Characters shall be uppercase or lowercase or a combination of both. §11B-703.5.2 c. Characters shall be conventional in form. Characters shall not be italic, oblique, script, highly decorative, or of other unusual forms. §11B-703.5.3 d. Characters shall be selected from fonts where the width of the uppercase letter “O”is 55 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”. § 11B-703.5.4 e. Minimum character height shall comply with Table 11B-703.5.5 Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign. Character height shall be based on the uppercase letter “I”. §11B-703.5.5 (See exception) f. Visual characters shall be 40 inches minimum above the finish floor or ground. § 11B-703.5.6 (See exceptions) g. Stroke thickness of the uppercase letter “I”shall be 10 percent minimum and 20 percent maximum of the height of the character. §11b-703.5.7 h. Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces. Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height. §11B-703.5.8 i. Spacing between the baselines of separate lines of characters within a message shall be135 percent minimum and 170 percent maximum of the character height. §11B-703.5.9 j. Text shall be in a horizontal format. §11B-703.5.10 5. Pictograms shall comply with the following: a. Pictograms shall have a field height of 6 inches minimum. Characters and Braille shall not be located in the pictogram field. §11B-703.6.1 b. Pictograms and their fields shall have a non-glare finish. Pictograms shall contrast with their field with either a light pictogram on a dark field or a dark pictogram on a light field. § 11B-703.6.2 c. Pictograms shall have text descriptors located directly below the pictogram field. Text descriptors shall comply with 11B-703.2 Raised Characters, 11B-703.3 Braille and 11B-703.4 Installation Height and Location. §11B-703.6.3 6. Symbols of accessibility and their background shall have a non-glare finish. Symbols of Accessibility shall contrast with their background with either a light symbol on a dark background or a dark symbol on a light background. §11B-703.7.1 7. Symbols shall comply with the following: a. The International Symbol of Accessibility shall comply with Figure 11B-703.7.2.1 ISA. The symbol shall consist of a white figure on a blue background. The blue shall be Color No. 15090 in Federal Standard 595B. §11B-703.7.2.1 (See exception) b. The International Symbol of TTY shall comply with Figure 11B-703.7.2.2. c. Telephones with a volume control shall be identified by a pictogram of a telephone handset with radiating sound waves on a square field such as shown in figure 11B-703.7.2.3. d. Assistive listening systems shall be identified by the International Symbol of Access for Hearing Loss complying with Figure 11B-703.7.2.4. e. Edges of signs shall be rounded chamfered or erased. Corners of signs shall have a minimum radius of 1/8 inch. §11B-703.7.2.6.4 E. SPECIAL ROOMS, SPACES, AND ELEMENTS F. BUILT-IN ELEMENTS DINING SURFACES AND WORK SURFACES (Note or show on the plans) 1.The tops of dining surfaces and work surfaces shall be 28 inches minimum and 34 inches maximum above the finish floor or ground. §11B-902.3 2.2. Where food or drink is served for consumption at a counter exceeding 34 inches in height, a portion of the main counter 60 inches minimum in length shall be provided in compliance with 11B-902.3. §11B-226.3 DIVISION 3 – BUILDING BLOCKS FLOOR OR GROUND SURFACE 1. Floor and ground surfaces shall be stable, firm, and slip resistant. §11B-302.1 2. Carpet or carpet tile shall be securely attached and shall have a firm cushion, pad, or backing or no cushion or pad. Carpet or carpet tile shall have a level loop, textured loop, level cut pile, or level cut/uncut pile texture. Pile height shall be ½ inch maximum. § 11B- 302.2, Figure 11B-302.2 3. Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with 11B-303 changes in level. Per 11B-302.2 CHANGES IN LEVEL 4. Vertical changes in level for floor or ground surfaces may be 1/4" high max. and without edge treatment. Changes in level greater than 1/4" and not exceeding 1/2" in height shall be beveled with a slope not steeper than 1:2. Per 11B-303, Figures 11B-303.2 & 11B-303.3 5. Changes in level greater than ½" in height shall be ramped and shall comply with the requirements of 11B-405 Ramps or 11B-406 Curb Ramps as applicable. §11B-303 TURNING SPACE 1. Floor or ground surfaces of a turning space shall be level with slopes not steeper than 1:48. [11B-304.2] 2. Circular turning space shall be a space of 60 inches diameter minimum with knee and toe clearance complying with Section 11B-306. [11B-304.3.1] 3. T-Shaped turning space shall be a space within 60 inch square minimum with arms and base 36 inches wide minimum. Each arm of the T shall be clear of obstructions 12 inches minimum in each direction and the base shall be clear of obstructions 24 inches minimum. [11B-304.3.2] CLEAR FLOOR OR GROUND SPACE 1. Clear floor or ground spaces shall meet the requirements of 11B-302 Floor or Ground Surfaces and shall not have changes in level except for slopes not steeper than 1:48 (2.083%). §11B-305 2. Clear floor or ground space shall be 30" minimum by 48" minimum. §11B-305.3, Figure 11B-305.3 3. Clear floor or ground spaces shall be positioned for either forward or parallel approach to an element unless otherwise specified. One full unobstructed side of the clear floor or ground space shall adjoin an accessible route or adjoin another clear floor or ground space. §11B-305.5, § 11B-305.6, Figure §11B-305.5 4. Clear floor or ground space may include knee and toe clearance complying with 11B-306 knee and Toe Clearance unless otherwise specified. §11B-305.4 KNEE AND TOE CLEARANCE 10. For built-in dining required to be accessible, toe clearance shall be provided that is 30 inches in width and 9 inches in height above the finish floor or ground for a depth of 19 inches minimum. § 11B-306.2.1 11. Space extending greater than 6" beyond the available knee clearance at 9" above the finish floor or ground shall not be considered toe clearance. §11B-306.2.4 12. Toe clearance shall extend 19 inches maximum under lavatories for toilet and bathing facilities and 25 inches maximum under other elements. §11B-306.2.2 13. At lavatories in toilet and bathing facilities, knee clearance shall be provided that is 30 inches in width for a depth of 11 inches at 9 inches above the finish floor or ground and for a depth of 8 inches at 27 inches above the finish floor or ground increasing to 29 inches high minimum above the finish floor or ground at the front edge of a counter with a built-in lavatory or at the front edge of a wall- mounted lavatory fixture. §11B-306.3.3, Figure 11B-306.3(c) 14. At dining and work surfaces required to be accessible, knee clearance shall be provided that is 30 inches in width at 27 inches above the finish floor or ground for a depth of at least 19 inches. §11B-306.3 15. Knee clearance shall extend 25" maximum under an element at 9" above the finish floor or ground. §11B-306.3.2 PROTRUDING OBJECTS 16. Except for handrails, objects with leading edges more than 27 inches and less than 80 inches above the finish floor or ground shall protrude no more than 4 inches horizontally into the circulation path. Handrails may protrude 4½ inches maximum. §11B-307.2, Figure 11B-307.2 17. Freestanding objects mounted on posts or pylons shall overhang circulation paths no more than 12 inches when located from 27 to 80 inches above the finish floor or ground. §11B-307.3, Figure 11B-307.3(a) 18. Protruding objects shall not reduce the clear width required for accessible routes. §11B-307.5 19. Lowest edge of a sign or other obstruction, when mounted between posts or pylons separated with a clear distance greater than 12 inches, shall be less than 27 inches or more than 80 inches above the finish floor or ground. §11B-307.3, Figure 11B-307.3(b) 20. Edge of signs or other objects, when mounted on posts or pylons with their bottom edges less than 80" above the floor or ground surface, shall be rounded or eased and the corners shall have a minimum radius of 1/8". §11B-307.3.1 21. Vertical clearance shall be at least 80 inches high on circulation paths except at door closer's and door stops, which may be 78 inches minimum abov e the finish floor or ground. §11B-307.4 REACH RANGES 22. Electrical controls and switches intended to be used by the occupant of a room or area to control lighting and receptacle outlets, appliances or cooling, heating and ventilating equipment shall be located within allowable reach ranges. Low reach shall be measured to the bottom of the outlet box and high reach shall be measured to the top of the outlet box. § 11B-308.1.1 23. Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles shall be located within allowable reach ranges. Low reach shall be measured to the bottom of the outlet box and high reach shall be measured to the top of the outlet box. §11B-308.1.2. 24. High forward reach that is unobstructed shall be 48 inches maximum and the low forward reach shall be 15 inches minimum above the finish floor or ground. §11B-308.2.1, Figure 11B-308.2.1 25. High forward reach shall be 48 inches maximum where the reach depth is 20 inches or less and 44 inches maximum where the reach depth exceeds 20 inches. High forward reach shall not exceed 25 inches in depth. §11B-308.2.2, Figure 11B-308.2.2 26. Where a high forward reach is over an obstruction, the clear floor space shall extend beneath the element for a distance not less than the required reach depth over the obstruction. §11B-308.2.2 27. High side reach shall be 48 inches maximum and the low side reach shall be 15 inches minimum above the finish floor where the side reach is unobstructed or the depth of any obstruction does not exceed 10 inches. §11B-308.3.1, Figure 11B-308.3.1 28. High side reach shall be 46 inches maximum above the finish floor or ground where the high side reach is over an obstruction more than 10 inches but not more than 24 inches in depth. § 11B-308.3.2, Figure 11B-308.3.2 29. Obstructions for high side reach shall not exceed 34 inches in height and 24 inches in depth. § 11B-308.3.2, Figure 11B-308.3.2 30. Operable parts on accessible elements, accessible routes, and in accessible rooms and spaces shall be provided a clear floor or ground space complying with 11B-305 Clear Floor or Ground Space and be placed within one or more of the reach ranges specified in 11B-308 Reach Ranges. § 11B-309.2 31. Operable parts shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist. Force required to activate operable parts shall be 5 pounds maximum. § 11B-309.4 32. Not Used. 33. Elements that are exempt from all requirements for operable parts requirements include electrical or communication receptacles serving a dedicated use; floor electrical receptacles; HVAC diffusers, exercise machines and exercise equipment and those operable parts intended for use only by service or maintenance personnel. §11B-205.1 34. Except for light switches, where redundant controls are provided for a single element, one control in each space shall not be required to comply with Section 11B-309 Operable Parts. §11B-205.1 DIVISION OPERABLE PARTS 1. Operable parts shall be placed within one or more of the reach ranges and the clear floor or ground space 30 inches by 48 inches minimum. [11B-309.2 and 11B-309.3] 2. Operable parts shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist. The force required to activate operable parts shall be 5 pounds maximum, except gas pump nozzles. [11B-309.4] DIVISION 4 - ACCESSIBLE ROUTES DOORS, DOORWAYS, AND GATES 1. There shall be no projections into the required clear opening width lower than 34" above the finish floor or ground. Projections into the clear opening width between 34" and 80" above the finish floor or ground shall not exceed 4". §11B-404.2.3 2. Not used. 3. Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 11B-309.4 Operation. Operable parts of such hardware shall be 34 inches minimum and 44 inches maximum above the finish floor or ground. Where sliding doors are in the fully open position, operating hardware shall be exposed and usable from both sides. §11B-404.2.7 4. Door and gate closing speed shall comply with the following: a. Door closer and gate closer shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position 12 degrees from the latch is 5 seconds minimum. §11B-404.2.8.1 b. Door and gate spring hinges shall be adjusted so that from the open position of 70 degrees, the door or gate shall move to the closed position in 1.5 seconds minimum. § 11B-404.2.8.2 5. The force for pushing or pulling open a door or gate other than fire doors shall be as follows: § 11B-404.2.9 a. Interior hinged doors and gates: 5 pounds maximum. b. Sliding or folding doors: 5 pounds maximum. c. Required fire doors: the minimum opening force allowable by the appropriate administrative authority, not to exceed 15 pounds. d. Exterior hinged doors: 5 pounds maximum. 6. Swinging door and gate surfaces within 10 inches of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door or gate. Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch of the same plane as the other and be free of sharp or abrasive edges. Cavities created by added kick plates shall be capped. §11B-404.2.10 7. Doors and side lights adjacent to doors and gates, containing one or more glazing panels that permit viewing through the panels shall have the bottom of at least one glazed panel located 43" maximum above the finish floor. §11B-404.2.11 DIVISION 6 – PLUMBING ELEMENTS AND FACILITIES TOILET AND BATHING ROOMS 1. Turning space shall be provided with the room and shall comply with Section 11B-304. [11B-603.2.1] 2. Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap. [11B-603.2.2] 3. Doors shall not swing into the clear floor space or clearance required for any fixture. Other than the door to the accessible water closet compartment, a door in any position may encroach into the turning space by 12 inches maximum. [ 11B-603.2.3] 4. Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches maximum above the finish floor or ground. Mirrors not located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 35 inches maximum above the finish floor or ground. [11B-603.3] 5. Coat hooks shall be located within one of the reach ranges specified in Section 11B-308. Shelves shall be located 40 inches minimum and 48 inches maximum above the finish floor. Medicine cabinets shall be located with a usable shelf no higher than 44 inches maximum above the finish floor. [11B-603.4] WATER CLOSETS AND TOILET COMPARTMENTS 1. The water closet shall be positioned with a wall or partition to the rear and to one side. The centerline of the water closet shall be 17 inches minimum to 18 inches maximum from the side wall or partition, except that water closet shall be 17 inches minimum and 19 inches maximum from the side wall or partition in the ambulatory accessible toilet compartment specified in Section 11B-604.8.2. Water closets shall be arranged for a left-hand or right-hand approach. [11B-604.2] 2. Clearance around a water closet shall be 60 inches minimum measured perpendicular from the side wall and 56 inches minimum measured perpendicular front he rear wall. A minimum 60 inches wide and 48 inches deep maneuvering space shall be provided in front of the water closet. [11B-604.3.1] 3. The required clearance around the water closet shall be permitted to overlap the water closet, associated grab bars, dispensers, sanitary napkin disposal units, coat hooks, shelves, accessible routes, clear floor space and clearances required at other fixtures, and the turning space. No other fixtures or obstructions shall be located within the required water closet clearance. [11B-604.3.2] 4. The seat height of a water closet above the finish floor shall be 17 inches minimum and 19 inches maximum measured to the top of the seat. Seats shall not be sprung to return to a lifted position. Seats shall be 2 inches high maximum. [11B-604.4] 5. Grab bars shall be provided on the side wall closet to the water closet and on the rear wall. [11B-604.5] 6. The side wall grab bar shall be 42 inches long minimum, located 12 inches maximum from the rear wall and extending 54 inches minimum from the rear wall with the front end positioned 24 inches minimum in front of the water closet. [11B-604.5.1] 7. The rear wall grab bar shall be 36 inches long minimum and extend from the centerline of the water closet 112 inches minimum on one side and 24 inches minimum on the other side. [11B-604.5.2] 8. Toilet paper dispenser shall comply with Section 11B-309.4 and shall be 7 inches minimum and 9 inches maximum in front of the water closet measured to the centerline of the dispenser. The outlet of the dispenser shall be below the grab bar, 19 inches minimum above the finish floor and shall not be located behind grab bars. 9. Wheelchair accessible compartments shall be 60 inches wide minimum measured perpendicular to the side wall, and 56 inches deep minimum for wall hung water closets and 59 inches deep minimum for floor mounted water closets measured perpendicular to the rear wall. [11B-604.8.1.1] 10. In a wheelchair accessible compartment with an end-opening door, either in-swinging or out- swinging, a minimum 60 inches wide and 48 inches deep maneuvering space shall be provided in front of the water closet. [11B-604.8.1.1.3] 11. Doors shall be located in the front partition or in the side wall or partition farthest from the water closet. Where located in the front partition, the door opening shall be 4 inches maximum from the side wall or partition farthest from the water closet. Where located in the side wall or partition, the door opening shall be 4 inches maximum from the front partition. The door shall be self-closing. Doors shall not swing into the clear floor space or clearance required for any fixture. 12. A side-wall grab bar complying with Section 11B-604.5.1 shall be provided and shall be located on the wall closet to the water closet. In addition, a rear-wall grab bar shall be provided. [11B-604.8.1.5] 13. Coat hooks shall be located within one of the reach ranges specified in Section 11B-308. Shelves shall be located 40 inches minimum and 48 inches maximum above the finish floor. [11B-604.8.3] URINALS 1. Urinals shall be the stall-type or the wall-hung type with the rim 17 inches maximum above the finish floor or ground. Urinals shall be 13½ inches deep minimum measured from the outer-face of the urinal rim to the back of the fixture. [11B-605.2] 2. A clear floor or ground space complying with Section 11B-305 positioned for forward approach shall be provide. [11B-605.3] LAVATORIES AND SINKS 1. A clear floor space complying with Section 11B-305, positioned for a forward approach, and knee and toe clearance complying with Section 11B-306 shall be provided. [11B-606.2] 2. A parallel approach complying with Section 11B-305 shall be permitted to a kitchen sink in a space where a cook top or conventional range is not provided and to wet bars. [11B-606.2 Exception 1] 3. Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches maximum above the finish floor or ground. [11B-606.3] 4. Controls of faucets shall comply with Section 11B-309. 5. Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact. There shall be no sharp or abrasive surfaces under lavatories and sinks. [11B-606.5] 6. Lavatories, when located adjacent to a side wall or partition, shall be a minimum of 18 inches to the centerline of the fixture. [11B-606.6] 7. Sinks shall be 6½ inches deep maximum. [11B-606.7] Knee clearance at lavatories shall comply with 11B-306.3. #10 GA EXPANDED MESH MATCH EXISTING STRUCTURE PLASTER L 1 1/4" X 3/4" X 1/8" 3/4" X 3/4" X1/16" CHANNEL WIRE TIED TO MET LATH 2X BLOCKING @ 2'-0" O.C. WHERE RAFTERS ARE PARALLEL TO HEAD 2 1/4 " 2 1/4 " 5" 5" 1' - 4" 2" 1/4" STEEL TYPICAL 1 1/2" 1 1/2" 1/4" HOLES FOR SCREEN FRAME 9/16 Ø HOLE FOR 1/2" Ø ANCHOR BOLT TYP. 9/16 Ø HOLE FOR 1/2" Ø ANCHOR BOLT TYP. 5" 2 1/4" 10 " 2 1/2" 1 1/2"1/4" HOLES FOR SCREEN FRAME 9/16 Ø HOLE FOR 1/2" Ø ANCHOR BOLT TYP. L 1/4" X 3/4" X 1/8" STEEL BEAM & POST 2" 2 1/4" #10 GA EXPANDED MESH MATCH EXISTING A5.0 4 #10 GA EXPANDED MESH MATCH EXISTING 8" CMU WALL 6"X 2" X 1/4" CHANNEL L 1 1/4"X 3/4" X 1/8" STEEL BEAM & POST A5.0 4 DOOR INTERIOREXTERIOR FLOORING PER SCHEDULECONCRETE 1 / 4 " 10 " A L U M I N U M K I C K P L A T E T Y P . PS-25-2401 CITY OF SANTA ANA PUBLIC WORKS AGENCY REVISIONS REFERENCES CONSTRUCTION COMPLETED: BENCHMARK NO.: SA-253-70 ELEV.: 176.00 (2010) PREPARED UNDER THE SUPERVISION OF: SHEET OF 1511 Cota Ave. Long Beach, CA 90813 Tel. 562-912-7900 Architecture Government Services Edward Lok Ng C-16840 REN.11/30/25 LICENSED A RCHITECT STATE OF C ALIFORNIA DRAWNDESIGNED:CHECKED: UNDERGROUND SERVICE ALERT OF SOUTHERN CALIFORNIA 811 ATTENTION IS DIRECTED TO THE POSSIBLE EXISTENCE OF UNDERGROUND FACILITIES NOT KNOWN OR IN A LOCATION DIFFERENT FROM THAT WHICH IS SHOWN ON THE PLANS OR IN THE SPECIAL PROVISIONS. THE CONTRACTOR SHALL TAKE STEPS TO ASCERTAIN THE EXACT LOCATION OF ALL UNDERGROUND FACILITIES PRIOR TO DOING WORK THAT MAY DAMAGE SUCH FACILITIES OR INTERFERE WITH THEIR SERVICE BEFORE EXCAVATING. THE CONTRACTOR SHALL VERIFY THE LOCATION OF UNDERGROUND UTILITIES BY CONTRACTING UNDERGROUND SERVICES ALERT. DIAL 811 LOK NG: REVIEWED FOR CONSTRUCTABLITY: RECOMMENDED FOR CONSTRUCTION: ARCHITECT INSTALLED 1700 E. SANTA CLARA AVENUE, SANTA ANA, CA 92705 FILE NO: PRINCIPAL CIVIL ENGINEER RCE NO.: PRINCIPAL CIVIL ENGINEER RCE NO.:G: \ P r o j e c t F i l e s \ 3 1 3 9 S a n t a A n a P o r t o l a P a r k R e s t o o m R e n o v & A d d f o r D V D \ 0 1 - D r a w i n g s \ 0 1 - R e v i t \ 3 - C D \ 3 1 3 9 S a n t a A n a P o r t o l a P a r k R e s t r o o m R e n o & A d d C D . r v t A5.0 PORTOLA PARK SPLASH PAD ACCESSIBLE DETAILS JSAF LN PO R T O L A P A R K S P L A S H P A D P R O J E C T N O . 2 5 -24 0 1 GENERAL ACCESSIBILITY. 1HEAD METAL SCREEN 4JAMB AT SCREEN ISO 3JAMB METAL SCREEN 2SILL METAL SCREEN 5THRESHOLD NUMBER DATE INITALS DESCRIPTION APPROVED SHEET 34 OF 57