Laserfiche WebLink
SET <br />HARDWARE <br />DOOR SCHEDULE : <br />DOOR NO ELEVATION <br />X.X.X <br />FT.SL.X <br />REPETITIVE NOTES: <br />NO <br /> <br />D E S C R I P T I O N <br />TAG <br />FASTENERS: <br />FT = Fastener Type, SL = Size and Length, X = P for Zinc Plated or S for Stainless Steel <br />D E S C R I P T I O N <br />REFERENCE DESCRIPTION <br />LEGEND <br />T .O .H. <br />ABBREVIATIONS <br />REFERENCE D E S C R I P T I O N <br />ELEVATION # <br />SHEET # <br />D .L .O.TOP OF HORIZONTALDAYLGHT OPENING DIMENSION <br />R. O.ROUGH OPENING DIMENSION <br />F. D.FRAME DIMENSION <br />D. O.DOOR OPENING DIMENSION <br />T .O .C.TOP OF CONCRETE <br />D. P.DIMENSION POINT REFERENCE <br />C CENTER LINEL <br />OPP.OPPOSITE HAND <br />BOTTOM OF WINDOWB.O.W. <br />TYP. <br />V.I.F. <br />TYPICAL <br />VERIFY IN FIELD <br />W.O.WINDOW OPENING <br />T.O.W.TOP OF WINDOW <br />GASKET No. <br />GASKET TABLE: <br />REFERENCE DESCRIPTION REFERENCE DESCRIPTION <br />WIND LOAD <br />DEAD LOAD <br />REFERENCE D E S C R I P T I O N <br />S.# <br />X.X <br />DETAIL # <br />SHEET # <br />SECTION # <br />SHEET # <br />= ANCHOR LOCATION <br /> INDICATOR <br />N.B.A.NOT BY ARCADIA <br />GLAZING SCHEDULE <br />GLASS SCHEDULE / MATERIAL LEGEND <br />D E S C R I P T I O N <br />1" INSULATED GLASS UNIT <br />T TEMPERED GLASS UNIT <br />SEALED INSULATING GLASS <br />W/ OPAQUE INTERLAYER @ INTERIOR PANE <br />HATCH <br />TYPE <br />1/4" GLASS UNIT <br />SEALANT AND BACKER ROD <br />SHIM AS REQUIRED <br />1" x 5 8" x 4" SETTING BLOCK, 2 PER LITE <br />1" x 5 16" x 4" SETTING BLOCK, 2 PER LITE <br />1" x 3 4" x 4" SETTING BLOCK, 2 PER LITE <br />HEAL BEAD OF SEALANT - ALL AROUND THE BASE <br />.040" THICK ALUM END DAM ATTACHED WITH (2) #6 F.H. S.M.S. <br />JOINERY SEALANT, BOTH ENDS OF HORIZONTAL <br />5 16" LONG WEEP SLOT WITH WEEP BAFFLE, 2 PER LITE. <br />SEALANT OVER ANCHOR <br />ANTI-WALK BLOCKS, 2 PER LITE <br />WATER DIVERTER SEALED TO HORIZONTAL, 2 PER HORIZONTAL <br />116" THICK ISOLATOR PAD TO SEPARATE DISSIMILAR MATERIALS <br />01 <br />04 <br />02 <br />03 <br />05 <br />06 <br />07 <br />08 <br />09 <br />10 <br />11 <br />#12 x 12" PAN HEAD SHEET METAL SCREW <br />#10 x 1 12" PAN HEAD SHEET METAL SCREW <br />#10-16 x 5 8" PAN HEAD SELF DRILLING SCREW <br />#8-32 x 1 4" PAN HEAD MACHINE SCREW <br />#12 x 12" FLAT HEAD SHEET METAL SCREW (UNDERCUT) <br />#12 x 5 8" FLAT HEAD SHEET METAL SCREW <br />#10 x 1 12" FLAT HEAD SHEET METAL SCREW <br />#6 x 12" FLAT HEAD SHEET METAL SCREW <br />PH.12xa.P <br />03a <br />03b <br />PH.10xa.P <br />PH.10xb.P <br />FH.12xa.S <br />FH.12xb.S <br />FH.10xa.S <br />FH.6xa.S <br />PH.8xa.P <br />VTLTG 3 16" GASKETG1 <br />GASKETGASKET NO. <br />SHEET NUMBER: <br />PROJECT NUMBER: <br />DATE: <br />ISSUE: <br />SHEET TITLE: <br />PROJECT: <br />CLIENT: <br />STAMP: <br />CITY OF SANTA ANA <br />20 CIVIC CENTER PLAZA, SANTA <br />ANA, CA 92701 <br />202305 <br />REVISION <br />NUMBER DATE DESCRIPTION <br />SANTA ANA <br />MEMORIAL PARK <br />AQUATICS CENTER <br />2102 S FLOWER ST <br />SANTA ANA, CA 92707 <br />REVISED SET <br />09/18/2025 <br />GENERAL NOTES <br />CW0.02 <br />04/13/2026 <br />BY <br />DATE 4/23/2026 <br />These documents (drawings, specifications, or calculations) have been <br />prepared by other design professionals or consultants who are licensed <br />and/or authorized to prepare such documents in California. These <br />documents have been examined by JAMA for design intent and have been <br />found to meet the appropriate structural requirements and the project <br />specifications. <br />JOHN A. MARTIN & ASSOCIATES, INC. <br />STRUCTURAL ENGINEERS <br />950 S. Grand Ave., Fourth Floor, Los Angeles, CA 90015 <br />Deferred Approval <br />rlawrence