2525 N Grand Ave & MTR01 - Plan - Laserfiche WebLink

Home Browse Search

ALL WORK SHALL COMPLY WITH ALL STATE AND LOCAL CODES AND ANY OTHER REGULATING AUTHORITIES WHICH HAVE AUTHORITY OVER ANY PORTION OF THE WORK. PRIOR TO COMMENCEMENT OF ANY WORK, THE CONTRACTOR SHALL VERIFY EXISTING CONDITIONS AND NOTIFY THE DESIGN PROFESSIONAL IN RESPONSIBLE CHARGE FROM TESLA OF ANY DISCREPANCIES. ANY WORK PERFORMED IN CONFLICT WITH THE CONTRACT DOCUMENTS SHALL BE CORRECTED AT THE SUBCONTRACTORS SOLE EXPENSE. SUBCONTRACTOR INITIATED CHANGES SHALL BE SUBMITTED IN WRITING TO TESLA FOR APPROVAL BEFORE MAKING ANY CHANGES. DEVIATION FROM PLANS BEFORE WRITTEN APPROVAL FROM TESLA PLACES LIABILITY ON THE SUBCONTRACTOR. ALL EQUIPMENT SHALL BE MOUNTED AS SHOWN. WHERE DETAILS ARE NOT PROVIDED, CONTRACTOR SHALL USE STANDARD CONSTRUCTION PRACTICES. ALL SURFACES SHALL BE PATCHED AND PAINTED AROUND NEW DEVICES AND EQUIPMENT TO MATCH EXISTING FINISHES. ANY METAL SHAVINGS FROM SITE WORK SHALL BE CLEANED FROM ALL SURFACES WHERE OXIDIZED OR CONDUCTIVE METAL SHAVINGS MAY CAUSE RUST, ELECTRICAL SHORT CIRCUITS, OR OTHER DAMAGE. APPROVALS FROM BUILDING INSPECTORS SHALL NOT CONSTITUTE AUTHORITY TO DEVIATE FROM THE DRAWINGS. NEW PAVEMENT INSTALLED AS PART OF THIS PROJECT SHALL MATCH EXISTING PAVEMENT SECTION. ASPHALT AND GAB DEPTHS SHALL BE MAINTAINED. GENERAL NOTES SUPERCHARGER NOTES 1.ALL CONDUIT FURNISHED AND INSTALLED BY CONTRACTOR. ALL WIRING FURNISHED BY TESLA AND INSTALLED BY CONTRACTOR. 2.ALL BUSHINGS AND WIRING INTERNAL OF PROPOSED SERVICE EQUIPMENT PROVIDED BY MANUFACTURER. ANY MODIFICATIONS SHALL REQUIRE ENGINEERING APPROVAL PRIOR TO ANY CHANGES BEING MADE. 3.ALL ALUMINUM(AI) CONDUCTORS TO RECEIVE ANTI-OXIDATION COATING DURING INSTALLATION. ALL OTHER CONDUCTORS ARE COPPER UNLESS OTHERWISE NOTED. 4.THE FOLLOWING CHARGING CABINETS AND THE CHARGING POSTS USED ON THIS PROJECT COMPLY WITH THE FOLLOWING STANDARDS: ·IEC 61851-23: 2014 / EN 61851-23: 2014 ·UL 2202: 2009(R2012) ·CAN CSA C22.2 NO. 107.1-01(R2011) 5.THE AFOREMENTIONED STANDARDS IDENTIFY THE REQUIREMENTS MET BY THE EQUIPMENT, INCLUDING BUT NOT LIMITED TO: ·PROTECTION AGAINST ELECTRIC SHOCK ·OVERLOAD AND SHORT CIRCUIT PROTECTION ·FAULT PROTECTION ·DEGREES OF PROTECTION AGAINST ACCESS TO HAZARDOUS LIVE PARTS ·THE INTERNAL COMPONENTS OF THE SYSTEM ARE PROPRIETARY. ANY QUESTIONS CONCERNING ACTUAL INTERNAL PROTECTIVE DEVICES MUST BE COORDINATED DIRECTLY WITH TESLA. 6.TESLA SUPERCHARGER SIGNAL WIRING RATED 1000V AND USED FOR POWER LIMITED CLASS 1 CIRCUITS SHALL BE PERMITTED TO RUN IN CONDUITS, CABLE TRAYS, WIRE WAYS, OR RACEWAYS ALONG WITH ASSOCIATED DC CONDUCTORS AS ALLOWED PER NEC 725.48(B)(1) AND 620.36. 7.SUPERCHARGER CABINET AC CONDUCTORS SIZED UNDER ENGINEERING SUPERVISION USING THERMAL MODELING SOFTWARE. SPECIFICATIONS ABOUT THE TRENCHING REQUIREMENTS ARE SHOWN IN E-501 8.FOR DC RUNS IN EXCESS OF 330 FEET, CONTACT TESLA. 9.UNDERGROUND CONDUITS SHALL BE SCHEDULE 40 PVC OR UL LISTED HDPE. THE ABOVEGROUND PORTION OF AN UNDERGROUND/ABOVEGROUND TRANSITION SHALL BE SCHEDULE 80 PVC OR UL LISTED HDPE. 10.ABOVEGROUND CONDUITS EXPOSED TO VEHICULAR OR EQUIVALENT PHYSICAL DAMAGE SHALL BE RMC. ABOVEGROUND CONDUITS NOT EXPOSED TO VEHICULAR OR EQUIVALENT DAMAGE SHALL BE PERMITTED TO BE EMT. 11.WIRE SPLICES ARE NOT PERMITTED TO EXTEND WIRE RUN LENGTH. CONTRACTOR IS RESPONSIBLE FOR RERUNNING FULL LENGTH OF WIRE IF RUN LENGTH IS MISCALCULATED. 12.SPECIAL INSPECTION IS REQUIRED FOR ALL POST-INSTALLED CONCRETE ANCHORS. 13.PLANT GUARANTEE: CONTRACTOR SHALL GUARANTEE ALL PLANTS FOR A PERIOD OF ONE (1) YEAR FROM DATE OF PROJECT ACCEPTANCE BY THE OWNER. CONTRACTOR IS RESPONSIBLE FOR PLANT MAINTENANCE FOR THE FIRST GROWING SEASON. 14.IF EXISTING GRASS IS DAMAGED/REMOVED DURING CONSTRUCTION, CONTRACTOR SHALL APPLY SEED PER HYDROSEED METHOD. RATING OF SEED SHALL BE PER DISTRIBUTOR BASED ON SPECIES TYPE. 15.CONTRACTOR SHALL MATCH EXISTING LANDSCAPE; USE GRASS, RIVER ROCK, MULCH ETC. TO MATCH EXISTING LANDSCAPE AROUND EQUIPMENT, UNLESS OTHERWISE NOTED. 16.CONTRACTOR TO INSTALL WEED BARRIER IN FRONT OF SUPERCHARGER CABINETS AND SWITCHBOARD. BARRIER TO EXTEND FULL WIDTH AND DEPTH OF NEC REQUIRED WORKING CLEARANCES. GENERAL NOTES 1.ALL ELECTRICAL WORK SHALL COMPLY WITH THE NATIONAL ELECTRIC CODE AS AMENDED BY APPLICABLE STATE AND LOCAL CODES. 2.ALL WIRING SHALL BE MANAGED IN A PROFESSIONAL, WORKMAN-LIKE MANNER AND MUST BE SUPPORTED, SECURED, AND PROTECTED TO PREVENT DAMAGE. 3.AC CIRCUIT CONDUCTORS SHALL BE IDENTIFIED BY PHASE AND SYSTEM PER ART 210.5 OR 215.12. UNLESS OTHERWISE REQUIRED BY ART 210.5(1) OR AHJ, COLOR-CODING OF POWER CONDUCTORS SHALL BE AS FOLLOWS: CONDUCTOR 277/480V 120/208V PHASE A BROWN BLACK PHASE B ORANGE RED PHASE C YELLOW BLUE NEUTRAL GRAY WHITE 4.DC CIRCUIT CONDUCTORS SHALL BE IDENTIFIED PER ART 210.5 OR 215.12: CONDUCTOR STD COLOR ALT COLOR DC+RED RED-STRIPED DC-BLACK BLACK-STRIPED 5.TERMINATIONS OF AC, DC, AND COMMUNICATIONS CONDUCTORS SHALL BE PROFESSIONALLY AND LEGIBLY LABELED WITH CIRCUIT SCHEDULE IDENTIFIER, CONDUCTOR SIZE (AS APPLICABLE) AND TERMINATION TORQUE. 6.ALL EQUIPMENT SHALL BE LISTED BY A NRTL IN COMPLIANCE WITH ART 110.3. WHERE EXISTING NRTL LISTING CANNOT BE MAINTAINED, ENGINEERING APPROVAL SHALL BE OBTAINED PRIOR TO EQUIPMENT MODIFICATION, AND THE EQUIPMENT SHALL BE RELISTED BY A SUITABLE NRTL. 7.UNDERGROUND CONDUCTORS & CABLES TO BE INSTALLED IN CONDUIT UON. 8.ALL WIRES SHALL BE PROVIDED WITH STRAIN RELIEF AT ALL ENTRY INTO BOXES AS REQUIRED BY NRTL LISTING. 9.REFER TO MANUFACTURER'S CURRENT PLANNING AND INSTALLATION MANUAL FOR TORQUE SPECS FOR ALL BOLTS AND TERMINAL CONNECTIONS. 10.ALL CONDUCTOR TERMINATIONS ON BUSSING OR TRANSFORMER SPADES SHALL BE MADE WITH HIGH-PRESS CRIMP LUGS UON. 11.ALL TERMINATIONS OF ALUMINUM CONDUCTORS SHALL BE PROPERLY INSTALLED WITH BEST PRACTICES INCLUDING BUT NOT LIMITED TO: ·USE OF TERMINATION EQUIPMENT RATED FOR ALUMINUM AT THE CONDUCTOR TEMPERATURE, CURRENT, AND VOLTAGE ·ALLOWANCE FOR MOVEMENT DUE TO THERMAL EXPANSION/CONTRACTION ·PROPER COATING OF EXPOSED ALUMINUM WITH ANTI-OXIDIZATION COMPOUND ·USE OF CALIBRATED DEVICES TO TORQUE AND MARK TERMINALS TO REQUIRED SETTINGS 12.DUCT SEAL COMPOUND SHALL BE APPLIED WHEREVER CONDUITS TRANSITION INDOOR/OUTDOOR OR UNDERGROUND/ABOVEGROUND. REFER TO EQUIPMENT NOTES FOR ADDITIONAL DUCT SEAL REQUIREMENTS. 13.BELL ENDS SHALL BE INSTALLED WHEREVER CONDUIT ENTERS EQUIPMENT FROM UNDERGROUND AND WHEREVER POTENTIAL FOR DAMAGE TO CONDUCTORS IS PRESENT AT ANY POINT. BELL ENDS SHALL NOT PREVENT THE USE OF GROUNDING FITTINGS OR COUPLERS WHEN REQUIRED. 14.ALL STUB-UPS WITHIN FLOOR-MOUNTED EQUIPMENT SHALL BE 3-5" ABOVE FINISHED GRADE. 15.ALL CONDUITS EXPOSED TO VEHICULAR OR EQUIVALENT PHYSICAL DAMAGE SHALL BE RIGID GALVANIZED STEEL. 16.GROUND LUGS SHALL BE RATED FOR THEIR ENVIRONMENT AND CONDITION OF USE. ELECTRICAL NOTES SITE LEGEND (EXISTING OBJECTS)UTILITY SOUTHERN CALIFORNIA EDISON CATEGORY ITEMS TESLA UTILITY PRIMARY PRIMARY TRENCHING X INSTALL PRIMARY CONDUIT X INSTALL PULL ROPE X INSTALL PRIMARY FEEDERS X PROVIDE PRIMARY FEEDERS X PROVIDE ROAD CUTS / ROAD BORES X PAVEMENT REPLACEMENT X TRANSFORMER INSTALL TRANSFORMER PAD X PROVIDE TRANSFORMER X INSTALL TRANSFORMER X INSTALL CONNECTIONS - PRIMARY X INSTALL CONNECTIONS - SECD X SWITCHBOARD PROVIDE METER X INSTALL METER X LAND SECONDARY FEEDERS X SECONDARY SECONDARY TRENCHING X INSTALL SECONDARY CONDUIT X INSTALL PULL ROPE X INSTALL SECONDARY FEEDERS X PROVIDE SECONDARY FEEDERS X PROVIDE ROAD CUTS / ROAD BORES X PAVEMENT REPLACEMENT X SCOPE OF WORK UNDERGROUND SANITARY LINE CLEANOUT GREASE TRAP FIRE HYDRANT IRRIGATION CONTROL VALVE LIGHT POLE UTILITY POLE HANDICAP PARKING SIGN DECIDUOUS TREE PALM TREE SS UNDERGROUND ELECTRIC LINEUE OVERHEAD ELECTRIC LINEOE 17. THE GROUND-FAULT PROTECTION SYSTEM SHALL BE PERFORMANCE TESTED WHEN FIRST INSTALLED ON SITE. THIS TESTING SHALL BE CONDUCTED BY A QUALIFIED PERSON(S) USING A TEST PROCESS OF PRIMARY CURRENT INJECTION, IN ACCORDANCE WITH INSTRUCTIONS THAT SHALL BE PROVIDED WITH THE EQUIPMENT, A WRITTEN RECORD OF THIS TESTING SHALL BE MADE BE AVAILABLE TO THE AUTHORITY HAVING JURISDICTION. 1"12"0 PROPRIETARY AND CONFIDENTIAL ABCDEFGH 1 2 3 4 5 6 DA T E NO . RE V I S I O N ORIGINAL SIZE 24"X36" SHEET SIZE ARCH "D" 3500 DEER CREEK RD. PALO ALTO, CA 94304 (650) 681-5000 02 . 1 0 . 2 6 A 20 2 5 C O D E & O V E R A L L P L A N 03 . 2 3 . 2 6 B BU I L D I N G D E P A R T M E N T C O M M E N T 25 2 5 N O R T H G R A N D A V E N U E SA N T A A N A , C A 92 7 0 5 , U S NOTES G-002 REV: B IFP MCARMONADIAZPLOT DATE: 4/21/2026 2:55 PM JB-9275533-00 TE S L A S U P E R C H A R G E R _ SA N T A A N A , C A 16 S U P E R C H A R G E R S