HomeMy WebLinkAbout10179795_2720 W. EDINGER - PlanODIC
Planning & Building Agency
Building and Safety Division
20 Civic Center Plaza
P.O. Box 1988 (M-19)
Santa Ana, CA 92702
(714) 647-5800
www.santa-ana.ora
ELECTRICAL SIGN
REQUIREMENTS
t6r137#A'7,B·$12"TYT)PM#fETR.,1,9.'a*FI:Dfa'¥t-£*Ait,·CERN *i,36t€,2,2043,1&1·7,Y,·ki;dl;-1-1,7*-2:n•--pf' 1118 Pr*If'AEE··'13fl# t·L,@fi#
Code references are to the 2010 California Electrical Code (CEC)
A. All signs require Planning Department approval.
B. All electrical signs require electric plancheck and permit.
1. Manufacturer's instructions are required at the time of submittal.
C-11: 3-21-2011
2. Submit detailed installation instructions including diagrams to the Building Department
for plan review at the time of submittal. Plans must include appropriate items noted by
this bulletin.
3. Cash or surety bond in the amount of $200.00 is required at time of issuance for each
address. The cash or surety bond will be refunded after all required finals.
C. A building permit is also required - except for open or highlight neon lighting.
D. Installation Requirements:7-9. 1.
CONTACT FIELD INSPECTOR PRIOR TO SIGN INSTALLATION.
(SEE SECTION G OF THIS BULLETIN)
1. Conductors and equipment shall comply with California Electric Code Article 600.
2. All metal parts of a sign shall be bonded in tlie manner specified in Article 250. Isolated
metal parts are permitted to be bonded by using an external green insulated conductor.
Equipment grounding & bonding conductors must be sized by 110.26 and protected from
physical damage. Minimum size is 14 AWG. CEC 600.7
3. A listed disconnect switch in the power supply primary, shall be installed within sight of
sign or have permanently installed means for locking in an "OFF" position. This is also
true for a transformer enclosure. CEC 600.6
4. A listed receptacle or an approved termination device shall be used for each neon
electrode. To relieve stress at terminations, tubing shall be supported with listed tube
supports in an approved manner within six inches of electrode connection.
CEC 600.41 & 600.42
5. Every electric sign of any type shall be listed by an approved testing laboratory and shall
be installed in conformance with this listing. That includes "l of x", "2 of x" labeling for
each separate unit of a multi-unit sign. CEC 600.3
6. All "can" letters and transformers housings shall have section labels that are readily
visible after installation. CEC 600.4
7. Transformers shall be located where accessible and be securely fastened in place.
Page 1 of 2
El
When not inside the sign, they need a 3 foot high x 3 foot wide x 3 foot deep workspace.
Transformers are permitted to be located in attics or canopies provided there is a
passageway at least 3 feet high x 2 feet wide with a minimum 12 inch catwalldwalkway
from the point of entry. Transformers must be securely fastened and independent of T-
bar when above a suspended ceiling. No part of sian mav be fed with flexible cord when
located above T-bar ceilings. CEC 600.21(E&F) & 400.8
8. Adequate illumination shall be provided for all working spaces about electrical
equipment. This applies to attics and canopies when entry is required to service or
inspect the equipment. At least one switch is required at entrance. CEC 110.34 & 600.21
9. Doorway to an attic or canopy space shall be minimum 3 feet by 2 feet wide.
CEC 600.21(E)
E. Open neon outline or highlight lighting.
1. To be treated as a sign by this department. However, Section D-5 & D-6 of this bulletin
will not apply.
2. Neon tubing shall be located where not normally exposed to physical damage. Open
neon tubing below 9 feet shall be protected from physical damage by an approved
shielding method. CEC 600.30 and 1 10.34(E)
F. Light-Emitting Diode (LED) Signs
1. Will be treated as a sign by this department. All sign rules in sections A, B, C, D, F, and
G will apply as appropriate.
2. LED illumination for signage must be a listed or recognized component. Many LED
manufacturers specify particular brands and models of transformers some do not.
Manufacturer information to clarify this issue is required on LED sign plans.
3. Unlisted LEDs may not be used in an electrical sign or as permanently installed
illumination. 110.3
4. Please have packaging or catalog cut-sheets on hand for inspector to review when LED
modules do not bear listing symbols.
G. Inspections
1. Contact an Electrical Inspector one (1) workday (minimum) in advance of installation to
arrange a site meeting on day of installation.
2. Call for inspection Monday through Friday, 8:00- 8:30 a.m. at (714) 647-5821. Approved
prints and the job card must be on site for inspection.
Page 2 of 2
June 19, 2013 SIGN COMPONENTS MANUAL (SAM) 2
Transformers and power supplies covered under this category are marked with a Type number from 1 to 8 in association with the
location designation "Indoors, ./Outdoors," "Weatherproof' or "WP." These Type numbers identify particular construction features
associated with a particular transformer or power supply as identified below:
• Type 1 - Open core-and-coil neon transformer or unenclosed neon power supply with body of the unit and input and output
terminals or leads that should be enclosed in accordance with end-product requirements.
• Type 2 - Neon supply with input and output terminals or leads that should be enclosed in accordance with end-product
requirements.
• Type 3 - Neon supply with input terminals or leads enclosed and intended for connection to a permanent wiring system, and
with output terminals or leads that should be enclosed in accordance with end-product requirements.
• Type 4 - Neon supply with input and output terminals or leads enclosed and intended for connection to a permanent wiring
system.
• Type 5 - Neon supply with input terminals or leads enclosed and intended for connection to a permanent wiring system and
provided with integral receptacles for output connection.
• Type 6 - Cord-connected neon supply provided with integral receptacles for output connection.
• Type 7 - Cord-connected neon supply with output terminals or leads that should be enclosed in accordance with end-product
requirements.
• Type 8 - Cord-connected neon supply with enclosed output terminals or leads.
ALLANSON INTERNATIONAL INC
33 CRANFIELD RD
E39591
TORONTO, ONTARIO CANADA M4B 3H2
Neon Power Supply, Indoor Type 7, Cat. No. SS935B-18.
Transformers, Outdoor Type 5
Applicable Conditions of Use - C, D, E.
Cat. Nos. 960Et<120,960EK277,960EK347, P960E1<120, P960EK277, P960E1<347,960EKF120,960EKF277,960EKF347,
P960EKF120, P960EKF277, P960EKF347,7560EK277,7560EK347, P7560EK120, P7560EI<277, P7560EK347,7560EKF277,
P7560EKF120, P7560EKF277, P7560EKF347,660EK120,660EK277,660EK347, P660EK120, P660EK277, P660EK347,
660 E KF 1 20,660 E K F2 77,660E KF 347, P660 E K F 1 2 0, P660 E K F2 77, P660 E KF34 7,560E K 1 2 0,560 E K347, P560E K '1 20,
P560EK277, P560EK347, 560EKF120, 560EKF347, P560EKF120, P560EKF277, P560EKF347,460EK120,460EK277,
460EK347, P460EK120, P460EK277, P460EK347,460EKF120,460EKF277,460EKF347, P460EKF120, P460EKF277,
P460EKF347,360EK120,360EI<277,360EK347, P360EK120, P360EK277, P360EK347,360EKF120,360EKF277,360EKF347,
P360EKF120, P360EKF277, P360EKF347.
Transformers, Outdoor Type 5
Applicable Conditions of Use - C. D, E.
Cat. Nos. Mini 330EK, Mini 430EK, Mini 530EK.
Power Supplies, Indoor Type 7
Applicable Conditions of Use - A, C, G.
Cat. No. SS9358-18,Cat. No. 630FNI.
Transformers, Outdoor Type 2
Applicable Conditions of Use - A. B.
Cat. Nos. 330CI120, P330CI120,330CI277, P330CI277,330CI347, P330CI347,430CI120, P430CI120,430CI277, P430CI277,
430CI347, P430CI347, 530CI 120, P530CI 120, 530CI277, P530CI277, 530CI347, P530CI347, 630CI120, P630CI120, 630CI277,
P630CI277,630CI347, P630CI347.
Transformers, Outdoor Type 4
Applicable Conditions of Use - A, B.
Cat. Nos. 330FI 120, P330FI 120, 330FI277, P330FI277, 330FI347, P330FI347, 430FI 120, P430FI 120,430FI277, P430FI277,
430FI347, P430FI347,530FI 120, P530FI 120,530FI277, P530FI277,530FI347, P530FI347,630FI 120, P630FI 120,630277,
P630FI277,630FI347, P630FI347.
1. The secondary circuits of these transformers are not to be interconnected in series or parallel.
2. The secondary circuits of these transformers are not to be connected to ground.
*May or may not be provided with a suffix "T"
FEVERBRITE LLC E122656
4949 S 110„
PO BOX 20020
GREENFIELD, WI 53220
Transformers, Outdoor Type 7.
Applicable Conditions of Use - A. C. G - Series 2612, Model 800-0128; Indoor Type 2, Series "NuAUX", Models 800-0174, 800-
0175, 800-0176,800-0177; Series 3612, Models 800-0232,800-0233
1. The "Animotion" system consists of the following components: Series 2612, Model 800-0128 or Series 3612, Models 800-0232
or 800-0233, Series "NuAUX," Models 800-0174, 800-0175, 800-0176, and 800-0177, and Animotion Controller Model 800-
0066,800-0067, or 800-0068.
2. Series "NuAUX," Models 800-0174, 800-0175, 800-0176, and 800-0177 are only for use with Series 2612, Model 800-0128 or
Series 3612, Models 800-0232 and 800-0233.
3. Each Class 2 output on Series 2612 Model 800-0128 and Series 3612, Models 800-0232 and 800-0233 shall not exceed 2.4 A.
4. A maximum of two "NuAux" transformers may be connected directly to each Model 800-0128, Model 800-0232 or Model 800-
0233 Class 2 output.
FRANCE A SCOTT FETZER CO E10092
June 19, 2013 SIGN COMPONENTS MANUAL (SAM) 40
3924 VARSITY DR
ANN ARBOR, MI 48108
Class 2 Powered LED Illuminated Sign, designated as "LED Beer Sign".
1. These products are only suitable for connection to a Class 2 power source rated 30 Volt DC or less.
2. These Class powered products are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
3. These products are suitable for use in dry locations with supply sources rated at 30 Volts DC or less.
EUROCOM-INC
SUITE 202
8411 STERLING ST
E342497
IRVING, TX 75063
LED Modules, Model Nos. SL-CL-420, SL-IP-CL-420, SL-HI-500, SL-HI-500RGB, SL-IP-HI-500, SL-IP-HI-500RGB, FK-IP-02, FK-
IP-03, FK-IP-04. All models may be followed by additional suffixes for color temperature.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
EVERBRITE ELECTRONICS INC
720 W CHERRY ST
E325903
CHANUTE, KS 66720
LED Modules, Class 2 LED Modules designated as "Current Limited LED Assembly" series, XXX-YYYY, where XXX may be any
combination of numeric characters from 000 to 999; YYYY may be any combinations of alphanumeric characters from 0000 to
9999 or AAM to ZZZZ, or suffix XXX-YYYYY , where XXX and YYY'YY can be any alphanumeric characters.
1. LED modules designated as "Current Limited LED Assembly" series, XXX-YYYY or XXX-YY'(YY are only suitable for
connection to a Class 2 power source rated max 60 Volt DC or less when used indoors.
2. LED modules designated "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY are only suitable for connection to
a Class 2 power source rated max 30 Volt DC or less when used outdoors.
3. LED modules designated as "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY have not been evaluated for
use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated
greater than 60 V DC for indoor use.
4. LED modules designated as "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY have not been evaluated for
use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated
greater than 30 V DC for outdoor use.
5. LED modules designated as "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY are each rated max. 90 watts
per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
6. LED modules designated as "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY are suitable for use only in dry
locations with supply sources rated at max. 60 Volts DC or less.
7. LED modules designated as "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYY'(Y are suitable for use in dry,
damp and wet locations with supply sources rated at 30 Volts DC or less
8. These products may be secured in place in the end product by any means available.
9. When these products are used in applications other than signs or Outline lighting, the need to conduct a temperature test shall
be considered.
10. These Class 2 LED modules are only suitable for use in Canada, when marked with Class 2 input voltage ratings 42.4 Vdc or
less for use in dry and damp locations, or rated 30 Vdc or less for wet locations.
EVERBRITE LLC
4949 S 110TH ST
PO BOX 20020
E131602
GREENFIELD, WI 53220
LED Modules, designated as Indoor Passively current limited (resistive) series, XXXXXXXX, where XXXXXXXX may be any
combination of alpha characters.
1. These products are only suitable for connection to a Class 2 power source rated 60 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 60 V DC.
3. These products are each rated max. 60 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. LED modules are suitable for use only in dry and damp locations with supply sources rated at min. 30 Volts DC to max. 60 Volts DC.
5. LED modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
8. LED modules rated for Class 2 input voltage of more than 42.4 V DC are only suitable for use in the United States.
Neon "Animotion" controller, Cat. Nos. 800-0066, -0067 and -0068.
41 SIGN COMPONENTS MANUAL (SAM)June 19, 2013
1. The Neon "Animotion" Controller shall be used within the ratings indicated above. Its input shall be powered by the Class 2
output of Model 800-0128 with the controller's output powering the input of Series "NuAUX" auxiliary transformers or the
controller's input shall be powered by a Listed Class 11 high-frequency power supply.
2. The controller has been evaluated at maximum marked ratings with Neon Power Supply Cat. No. 1212 and Cat. No. 800-0065
auxiliary transformer.
3. The number of outputs on the controller may var·y between one and eight.
4. No more than four outputs, with a maximum of two outputs per input, may be operated continuously.
5. All eight outputs shall not be on concurrently.
6. The controllers are intended for Indoor Use Electric Signs or shall be mounted in suitable enclosure when used with Outdoor
Use Electric Signs.
LED Modules, Sequencer Series Modules designated XXX-XXXX, XXX-YYYY or XXX-YYYYY (XXX-XXXX, XXX-YYYY or XXX-
YYYYY may be any combination of alpha characters).
1, These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less.
2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2
circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be
required.
3. Each module is rated and suitable for a maximum of 90 watts.
4, Sequencer modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less.
5, Sequencer modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less.
6. These modules should be secured by suitable means when installed in the end-use application.
7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require
additional evaluation.
8. When the Sequencer modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these
application are only suitable for use in the United States.
LED Modules, Regulator Series Modules designated XXX-XXXX, XXX-YYYY or XXX-YYYYY (XXX-XXXX, XXX-YYYY or XXX-
YY'(YY may be any combination of alpha characters)
1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less.
2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2
circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be
required.
3. Each module is rated and suitable for a maximum of 90 watts.
4. Regulator modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less.
5. Regulator modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less.
6. These modules should be secured by suitable means when installed in the end-use application.
7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require
additional evaluation.
8. When the Regulator modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these
application are only suitable for use in the United States.
LCD Module, Model LCD v6.x with Power Supply.
1. These LCD modules are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These LCD modules have not been evaluated for use and connection to a power supply source with parameters that exceed
Class 2 circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be
required.
3. Each LCD module is rated and suitable for a Class 2 maximum 12 Vdc output of 43 watts.
4. The Exclusion of Water Test may be waived for this LCD module subassembly only when installed in outdoor location signs with
Listed conduit and (QCRV) liquid tight conduit fittings on primary circuits.
5. These modules should be secured by suitable means when installed in the end-use application.
6. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require
additional evaluation.
LED Modules, Cat. No. LCD v6.x with Power Supply.
1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less.
2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2
circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be
required.
3. Each module is rated and suitable for a maximum of 90 watts.
4. Regulator modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less.
5. Regulator modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less.
6. These modules should be secured by suitable means when installed in the end-use application.
7, These modules are suitable for use in signs only. The use of these modules in any other end-use application will require
additional evaluation.
8. When the Regulator modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these
application are only suitable for use in the United States.
EVERBRITE LLC E360604
SUITE 208
BLDG B
380 SEMORAN COMMERCE PL
LED Modules, Models CST-2D-B, CST-2D-G, CST-20-R, CST-20-RGB, CST-20-W, CST-30-A, CST-30-8, CST-30-G, CST-3D-
R, CST-3D-RGB, CST-30-W, CST-30-V\AA/, CST-40-B, CST-40-G, CST-40-R, CST-4D-RGB, CST-40-W.
1, These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2, These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12VDC.
June 19, 2013 SIGN COMPONENTS MANUAL (SAM) 42
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
EXCELLART SIGN PRODUCTS LLC
1654 S. LONE ELM RD
E152309
OLATHE KS 66061
Frame system, Series EC(+) followed by -4, -4R, -6, -6R, -7, -7R, -8, -8R, -9, -9R, -12 Hinged and Standard, -D/F Hinged and
Standard, -IDS, -S/F Hinged and Standard, or EC-S/F Access System. Accessories for use with EC frame systems, frame, angle,
hat section, 6 in. radius corner, 9 in. radius corner, Cat. Nos. EC-4, -7, -8, EC-IDS, EC-Xtra, FF, FF-2, H-1, H-1.5, LC, LF, RR, or
RRC retainers, Cat. No. EC-12 frame retainer brace, Cat. No. EC-S/F access system, Cat. No. EC lamp raceway, Cat. No. EC
raceway cover, Cat. No. EC lamp/ballast track, Cat. No. EC-IDS raceway, Cat. No. EC Flex System for standard frame, hinged
frame, or retro fit, Cat. No. EC-Tl, -T2 trim caps, or Cat. No. 1 1/2, 2 1/2, or H divider bars. Cat. Nos. F retainer, F hinged retainer,
FF short retainer, EC-3.25 radius post, EC-3.25 rectangular post, EC-revel connector, EC-3.25 bleed frame, EC-8 in. radius
quarter end, EC channel letter front, EC channel letter back, EC channel letter lid.
Frame system Excellart (++) followed by C, C-2, M-C, or MC-R, for use with retainers MC- Alternate M-C, ZF.188, ZF.250, ZF-1
1/2, ZF-2, ZFC2 1/2, or ZFC-3. Frame system Narrowline, Cat. Nos. EC-4RN frame, EC-4N frame, 1 in. radius corner connector
and cap.
(+) Frames, angles, and hat sections have the same catalog number as the frame system. Frames available in standard or hinged
versions.
(++) Frames available in smooth or ribbed versions.
Expanda Frame Model AMB13920. Lamp Socket Raceway and Cover Models AMB990 and AMB991.
1, When installed in an outdoor wet location application, consideration shall be given to conducting the water exclusion test of UL
48.
2. The suitability of the components to serve as wireways and electrical enclosures shall be determined in the end use.
3. When installed in an outdoor wet location, the bottom of the cabinet system shall be provided with at least two drain holes in
each inside recess, except for the wireway.
FANTASTIC DISPLAYS INC
2049 S BAKER AVE
E362917
ONTARIO, CA 91761
Class 2 powered LED modules, Cat. Nos. LMYX 225 [+1, LMYX 324 [+1, LMYX 220 [+1, LMYX 332 [+1, LMYX 340 [+L LMYX 326
[+1, LMYX 341 [+1, LMYX 112 [+1, LMYX 120 [+1, LMYX 102 [+], LMYX 117 [+1.
1. This product is only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. This product has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limits and which is rated greater than electrical ratings.
3. This Class 2 LED module is rated as noted in the electrical ratings tables. When units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. This product is suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. This product is not required to be enclosed or protected from the weather in the end product.
6. This product may be secured in place in the end products by any means available.
FEDERAL HEATH SIGN CO. LLC
4602 NORTH AVE
E125271
OCEANSIDE, CA 92056
Sign face tensioning systems, designated "KLICK-RAIL".
1. Water exclusion must be determined in the end product.
2. Any frame dimension greater than 1.8m (6 feet) needs to be braced to prevent billowing.
3. This system limited to only decorative applications, and together with the flexible face material shall comply with the external
decorative face requirements of UL 48, particularly the clearances from heat-generating components to decorative plastic
panels.
4. The suitability of secureness of the clamp and flexible material shall be judged in the end-use application.
5. The installation of this system in a sign shall conform with the instructions provided with this tensioning system.
Class 2 Powered LED Modules, designated RVI Series.
1. These products are only suitable for connection to a UL Listed or UL Recognized Class 2, DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LED Illumination, RVI Series is rated 20 W per 2.7 m length with yellow LEDs and 21 W per 2.7 m length with Red
LEDs. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply and 60 W per Class 2 circuit.
4. These products are suitable for use in dry, damp locations. When the Class 2 output is 12 Vor under, these products are
suitable for wet locations.
5. These products are not required to be enclosed or protected from weather.
Controller boards, Models PCB64PD, PCB32PD, PCB06PD.
1. The controller and drivers covered by this report are suitable for damp and dry locations only.
2, The controller Models PCB64PD, PCB32PD, and PCB06PD are suitable for use on a 120 V, 60 Hz service and are capable of
switching up to 64,32, and 6 points, respectively. They are for use only with triac driver Models PC820T6, PCB10T1 2, and
PCB10T4.
3. The Model PCB20T6,6 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a maximum
load of 13 A, 1560 W.
*018)682. 1/4 655- - 36 a.77 04
312- fLAN_
PLANN48*G DiVISION
MASTER I.D .206 1\\9289
G.P.an-Zone (23)
PLANNER-k.-_
TRANSFERNES'lBY DATE -PLANNING iNSPECT!ON REQUIREDROUGH 0 FINAL - -TACDNAME_ -*€14
f
RETAIN PLANE f·OR FUT!;RE REVISIONS.SUBJECT TO i-f ENS CHE'KED AND CONDITIONSBELOW:
3-51300 LA) %O 1 T.' CSLY €! O NO EXTE:I:.<:4·, ALTE 41- ONS/MODIFICATIONS _
tail f\-C
0 0 ,ALL R..1,4.'TER: M.S TO ATCH EXISTiNG? O SCREENiNG REQUA D1 0 SUBMIT LANDSCAPI SLANS
CON[)113(3NS
15*241
L
.ItL
1
VL.
Z
1.-
K
0
€
74'
9.2.
bed' -
IM , sl
22107 961221
et*Flep-
ial X
.«4 U
1
.9
BEFORE
:94?ZI: Everbi
4
1:ni
4r 4'.9.-0 $8.11/'/I'l.
I ,
AFTER
ite DISCLAIMER: Renderinas are for araohic ourooses onlv and not intended for actual constnlction dimensions. F Y windload reauirements. actual dimensions and mountina detad olease refer to enaineerinc soecificatons and install drawinas.
These arawings ana aesigns are Ine exclusive property of Everbrite LLC Use of, or auplicailon n any manner wlinoul express written permission oi tverunce LLC Is proniolted.
¥,>: C..Customer: Taco Bell ·Description:Customer Approval: NoTE: Unless specified by customer, all depth of embossing will be
Project No: 297488 Scale: NTS Drive Thru Menu Board .determined by Everbrite Engineering or existing customer specifications on file. Colors and graphics
on file will be used unless otherwise specified by customer.Date: 7/1/13 - |Drawn By: RB Please read carefully, check appropriate box and fax O Sketch OK as is
Location & Site No Revised:back to Everbrite:O New sketch required
Sarita Ana, CA Site: TB2772 Revised:SIGNATURE DATE
i
91.375"2.\ 1 11.5
no" LA \ 1 I 7.5"
F 1 1 (41
.584"r--GU¤ty &GENERAL SPECIFICATIONS:
18
L
70.131
4
15.994"
Materials: Aluminum sheets & steel tubes
I IDecoration: PoOvder coat Taco Bell Bronze & black
Arch & Bell Area Squared: 9.29 Sq. Ft.
Menu Board Area Squared: 44.50 Sq. Ft.
Weight (Est.):
· 745 lbs. (crated)
· 595 lbs. (uncrated)
ELECTRICAL
Illumination:
· White LEDs
Power Supplies:
· (2) 062-00008 Electronic LED Power Supplies
Line Load:
· 1.92 amps @ 120 vac-60Hz
· (1) 20 Amp circuit
FRONTVIEW
SCALE: 1/20=1'-O L 33.0"
r-9"-1
COLORS:SIDE VIEW
SCALE: 1/2-=1'-0-Exterior:
Doors & Mullions: Powder coat Taco Bell Black
Cabinet: Powder coat Taco Bell Bronze
1 4%-1
6.
BASE PLATE DETAIL -SCALE: 1=1 '-0
£ 0
6-1 L-1.0" thick f
3
Tliose product sheets are the exclusive property 01 Everbrito LLC. Use of this property In any manner without express wntton permission of Everbnte LLC is proh,b:ted. Drawings ire for graphipurposes orlly and not uttended for actual construction. For more spedric manulactunng detail please refer to eng:noerng specifications and *stall drintings.
.....Everbrite LLC Part No: E003535P Project No: 291388-2
... 000.:..4949 S 110th Street. Greenfield. Wl 53220 Description:Date: 2/12/134.....: Everbrite Phone: 414-529-3500 · Fax: 414-529-7191 DriveThru Evolution LEDVE Menuboard TA«ZOBELLWebsite: www.everbrite.com with Arch Drawn By: RB
8.4375
8'-21/8.
8'-111/4'
17 1/C 1' 115ILLUMINATED EXTENDER 26 3/EMT'G DETAIL TOP VIEW MAX
4'-35,
0 ILLUMIN
1'-11 7/16' Toppi
11 I
SINGLE
ILLUMINATED EXTENDER TAC
8'-7 7/16'
5'-40 -
/19
. 1'-9 1/4' 15
==3 5/16' DIA.TRIPLE HIGH EXTENDER
LOGO DISPLAY MT'G DETAIL TOP VIEW
/8.
- -UFING ANG\iS
'ATED
-R
- ILLUMINATED TOPPER
TRIPLE MT'G DETAIL SIDE VIEWO HIGH
ExTENDER · 6'-5 7/16"
C £01
15U1\¥ 7
BELL
MENU
BOARD
_C<Ji
3' X 3' TUBE-- I |
ELECTRICAL DATA:
MENU BOARD
LAMPS: (4) F60T12 CW/HO
BALLAST (1) 6Gj959
2.9 MIPS
TOPPER
LAMPS: (1) F24n 2 CW/HO
BALLAST (1) 51-609-XR/256-148
.55 TOTAL AMPS
MENU BD EXTENDER
LAMPS: (1) F42T12 CW/HO
BALLAST 0) 51-609-XR
.55 TOTAL AMPS
(1) 15 AMP CIRCUIT 120V RE®
RIPLE HIGH EXTENDER
.90 TOTAL AMPS
(1) 20 AMP CIRCUIT 120V REQ'D
LAMPS: (1) F72T12 CW/HO
BALLAST (1) 51-742-R/256-248
INSTALLER INSmUCTIONS
1. STAKE FOUNDANON AREA AND CONFIRM ANAL
GRADE REQUIREMENTS WITH G,C
2. EXCAVATE FOUNDATION AREA.
3. SET ANCHOR 80LTS CAGE PLUMB,INSTALL CONDUIT
STUBS AND POUR CONCRETE. (PRIMARY ELECEICAL
SERVICE TO BASE BY G.C.)
4. ALLOW CONCRETE CURE TIME AS REQUIRED.
5. INSTALL SIGN ON ANCHOR BOLTS. LEE SIGN
AND GROUT AROUND ANCHOR BOLTS.
6. REMOVE UFENG BRACKET AND RONSTALL BOLTS.
7. CLEAN UP AREA AND REMOVE ANY PACKING MATL
NOTE:
INSTALLATION MTG OF UUM TOPPER, ILLUM &
NON ILLUM. EXTENDERS, AND ILLUM mIPLE
EXTENDER. SEE DWGS. IN00152P, & IN00886B
DESIGN SPECIFICATION: 3000 P.S.I. CONCRETE .33 CU. YDS
TOTAL
6'-8'
SINGLE
NON-ILLUM.
EXTENDER
1'-4"
%
- [Ee =EL
GRADE
12" MIN
OR CODE
4.9 AMPS TOTAL
(FOR SIGN UGHTING)
r
7-f-
/\3\« Y
SWITCH
DESIGN NOTES:
1. SIGN, AND BASE ARE DESIGNED TO WITHSTAND
A MID LOAD OF 30 P.S.F.
2. ALL CONCRETE EXCEPT CONCRETE USED FOR BACK
FlLL SHALL- DEVELOP A MINIMUM COMPRESSIVE
STRENGTH OF EDO P.Sl
3. CONCRETE BASE DESIGNED USING GOOD TO AVERAGE
SOILS HAVING AN ALLOWABLE CAPACITY
OF 400 P.S.F./FL
4. ALL FOOTING EXCAVATIONS ARE TO BE FREE OF WATER
AND FOREIGN MATTER BEFORE PLACING CONCRETE.
' 79;. ·-'44··\ELECTRICAL CONDUIT
: ·. .: BY OTHERS. \
3/4'-10 X 20 1/4' LG. ANCHOR BOLTS · ·U. ANCHOR BOLT
W/4" HOOK &5' THRD LENGTH
(4) REQ'D
NUT\PROJECTION \ 1
LEVEUNG- ,":.:
OUTLINE OF BASE COVER J n.-'13„5. IF THESE SOIL CONDITIONS III NOT EXIST AT THE
FOUNDATION LOCATION, IT IS THE ERECT[R'S
RESPONSIBILITY TO NOTIFY EVERBRITE, INC
FRONT OF SIGN PRIOR TO PERFORMING ADDITIONAL EXCAVATION
OR ANY CONCRETE PLACEMENTANCHOR BOLT & CONDUIT SETTIN6
,LOCK VASHER (SCALE FULL)MAIN MENU BD. E 00036BR TOPPER PVD 20065
SIDE MENU BD. PVD 20179 MNBD. EXTENDER E 00098B-FLAT WASHER
These drawings are then ...74: E verb rite
1""":'® 4949 So. 110th St.exclusive property of Everbrite, Inc.
| 1'-6' DIA | lilli Al TER POLE IS LEVELED AND P.O. Box 20020 Use of, or dupliGotion in any mannerBOLTED INTO PLACE, FILL ENTIRE
AREA UNDER PLATE WITH STRUCTURAL Greenfield, Wl 53220 without express 5ritten permission
NON-SHRINK, NON METALIC CEMENTIT[OUS 414-529-3500 of Everbrite,Inc. is prohibited.
GROUT, FOLLOW ALL OF THE MANUFACTURERS TITLE
INSTRUCT]ONS FOR ALL GROUT MIXING,TACO BELL OUT DOOR MENU BDA RELEASE TO INSTALL 5-27-03 pi PLACEMENT, AND CURING.
SYM DESCRIPnON DATE CHG ECN DRN HED DT 5-27-03 SCALE DRWG NR REV
REVISION RECORD CKD PJL DT 5-27-03 1:30 IN01340B A
14 Ed\ n le 0
4nnect for the monument sign(s) ismost
501 6*G ,e deu iritoe Of' 9Jired or tb -licated circui breaker(s)
"4\600%1 oflockable
s*ro Bss* 0·dn 8Access to any p attic or above11 be imm a ladder600-21 (d)(d)09.0 ..Adifig M
*lin12-inon \Na.City of Santa Ana Planning enc
.
PERMIT TYPE:LDLLBG
d
)..1-.I -I-*.*.
MECH FRADING,
ELECTRICAL t PERMIT#101/79/lc*2015;2%11 PLAN APPROVAL . OCC. GROI JP1 -This set of plans and specifications must be kept on CONSTR. TYPF .-.the job at all times and it is unlawful to make anychanges or alteraUons on same without written per-CODE EDITION 520 YOmission from the Department of Building SafetyCity of Santa Ana.FLOOD ZONE
£.9
The approval of this plan and specifications SHALL
-1NOT,42!eld to permit nor be an approval of the FLOOD ZONE CERTIE REQ'D YES 10 :violation or any provisions of ANY CIty Ordinanceor State Law.
MICROFILM YES AbhApprotGa29 -443:>RADIANT BARRiER @ ROOF YES N.UCITY OF SANTA ANA 1 RESIDENTIAL DEV. FEE YES (60DEPARTMENT OF BUILDING SAFETY
SCHOOL DISTRICT YES N1-
W*,f4;U»eL=Sh,Ut-hum.3».0.- 4.-·. 7
1-1 3 - 6
C
0