HomeMy WebLinkAbout10179885_1247 S. MAIN - PlanPlanning & Building Agency
Building and Safety Division
20 Civic Center Plaza
P.O. Box 1988 (M-19)
Santa Ana, CA 92702
(714) 647-5800
www.santa-ana.org
ELECTRICAL SIGN
REQUIREMENTS
iFiF-/*/Af. + + +51223201.4-kil(4g***· -ff,>v. 3:2 '.. "- ': -?1Wb,+1:Vi.kifili,'9:45;&.9 35,.5 -96%411*4WY'-2953+i*f.eyfq ,*f,)22&;39,74.1%% 21,:-·,filiafr
Code references are to the 2010 California Electrical Code (CEC)
A. All signs require Planning Department approval.
B. All electrical signs require electric plancheck and permit.
1. Manufacturer's instructions are required at the time of submittal.
C-11: 3-21-2011
2. Submit detailed installation instructions including diagrams to the Building Department
for plan review at the time of submittal. Plans must ihclude appropriate items noted by
this bulletin.
3. Cash or surety bond in the amount of $200.00 is required at time of issuance for each
address. The cash or surety bond will be tefunded after all, required finals.
C. A building permit is also required - except for open or highlight neon lighting.
D. Installation Requirements:Efl' ./4 '·
CONTACT FIELD INSPECTOR PRIOR TO SIGN INSTALLATION.
(SEE SECTION G OF THIS BULLETIN)
1. Conductors and equipment shall comply with California Electric Code Article 600.
2. All metal parts of a sign shall be bonded in trie manner specified in Article 250. Isolated
metal parts are permitted to be bonded by using an external green insulated conductor.
Equipment grounding & bonding conductors must be sized by 110.26 and protected from
physical damage. Minimum size is 14 AWG. CEC 600.7
3. A listed disconnect switch in the power supply primary, shall be installed within sight of
sign or have permanently installed means for locking in an "OFF" position. This is also
true for a transformer enclosure. CEC 600.6
4. A listed receptacle or an approved termination device shall be used for each neon
electrode. To relieve stress at terminations, tubing shall be supported with listed tube
supports in an approved manner within six inches of electrode connection.
CEC 600.41 & 600.42
5. Every electric sign of any type shall be listed by an approved testing laboratory and shall
be installed in conformance with this listing. That includes "1 of x", "2 of x" labeling for
each separate unit of a multi-unit sign. CEC 600.3
6. All "can' letters and transformers housings shall have section labels that are readily
visible after installation. CEC 600.4
7. Transformers shall be located where accessible and be securely fastened in place.
Page 1 of 2
When not inside the sign, they need a 3 foot high x 3 foot wide x 3 foot deep workspace.
Transformers are permitted to be located in attics or canopies provided there is a
passageway at least 3 feet high x 2 feet wide with a minimum 12 inch catwalk/walkway
from the point of entry. Transformers must be securely fastened and independent of T-
bar when above a suspended ceiling. No part of sign mav be fed with flexible cord when
located above T-bar ceilings. CEC 600.21(E&F) & 400.8
8. Adequate illumination shall. be provided for all working spaces about electrical
equipment. This applies to attics and canopies when entry is required to service or
inspect the equipment. At least one switch is required at entrance. CEC 110.34 & 600.21
9. Doorway to an attic or canopy space shall be minimum 3 feet by 2 feet wide.
CEC 600.21(E)
E. Open neon outline or highlight lighting.
1. To be treated as a sign by this department. However, Section D-5 & D-6 of this bulletin
will not apply.
2. Neon tubing shall be located where not normally exposed to physical damage. Open
neon tubing below 9 feet shall be protected from physical damage by an approved
shielding method. CEC 600.30 and 110.34(E)
F. Light-Emitting Diode (LED) Signs
1. Will be treated as a sign by this department. All sign rules in sections A, B, C, D, F, and
G will apply as appropriate.
2. LED illumination for signage must be a listed or recognized component. Many LED
manufacturers specify particular brands and models of transformers some do net.
Manufacturer information to clarify this issue is fequired on LED sign plans.
3. Unlisted LEDs may not be used in an electrical sign, or as permanently installed
illumination. 11'0.3
4. Please have packaging or catalog cut-sheets on hand for inspector to review when LED
modules do not bear listing symbols.
G. Inspections
1. Contact an Electrical Inspector one (1) workday (minimum) in advance of installation to
arrange a site meeting on day of installation.
2. Call fbr inspection Monday through Friday, 8:00- 8:30 a.rn. at (714) 647-5821. Approved
prints and the job card must be on site for inspection.
Page 2 of 2
133 SIGN COMPONENTS MANUAL (SAM)October 1, 2013
SINO-OPTO USA LLC, DBA LED LIGHTING SERVICES LLC E342085
3575 COMMERCIAL AVE
NORTHBROOK, IL 60062
LED Tube, Cal. Nos. LLIT8-48-18W, LLIT8-24-10W
1. These products are suitable for use in dry, or damp locations.
2. The lamp is maintained not less than 2 inches (50.8 mm) from combustible materials such as wood or plastic and parts that are
a source of heat or arcing. Spacing from lampholder to sign housing is zero.
3. This LED lamp is not for use with internally shunted bipin lampholders used with fluorescent instant start lamps.
SINO-OPTO USA LLC, DBA LED LIGHTING SERVICES LLC E345360
3575 COMMERCIAL AVE
NORTHBROOK, IL 60062
LED Tube, Cat. No. SN-T
1. These products are suitable; for use in dry, or damp locations.
2. The lamp is maintained not less than 2 rinches (508 min) from combustible materials such as wood or plastic and parts that are
a source of heat or arcing. Spacjng from lampholder to sign housing is zero.
3. This LED lamp is not for Ose'with internally shonted bipin lampholders used with fluorescent instant start lamps.
LED Tube, Cat No. LLI-T10DBL.
1. Manufacturer's name, trade name, or trademark.
2. Distinctive catalog or model number.
3. The electrical ratings.
* When multiple manufactures are involved, then a Factory ID identifying the product to a particular factory shall be provided.
5. Optional - "For Connection with Class 2 Circuits Only."
SLOANLED, DIV OF SLOAN CO INC
5725 OLIVAS PARK DR
E215393
VENTURA, CA 93003
LED Modules, Cat. Nos. 701261, 701261-PW, 701340, with suffix -Ri -O, -Y, -8,-G, -W or -A: Cat. Nos. 701340-PW with suffix -
R, -O, -Y, -A, -8, -G or -W, Cat. No. 701340-CM.
1.These products are only suitable for connection to a UL Listed or Recognized Class 2,24 V dc power source for Model 701340
and 7.5 V dc or 5 V dc power source for Model 701261
2 These products have not been evaluated for use when connected to a power source that does; not comply with Class 2 vdltage
and energy limited supplies.
3 The total number of Model 701261 LED Lighting Units are not to exceed a total of 75 units per Class 2 circuit. The total number
of Model 701340 LED Lighting Units are not to exceed a total of 40 units per Class 2 circuit.
4.These products are suitable for use in dry, damp and wet locations.
5.These products are not required to be enclosed or protected from weather.
Class 2 LEDs, "ThinLED", Model 701228, with suffix -A, -8, -G, -R, -W or -Y: Cat. No. 701228-18, with suffix -A, -8,-G, -R, -W or -Y.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, max. 12 V dc power source. . Only
Models 701228-A, -R, or -Y are only suitable for connection to UL Listed or Recognized Class 2, max. 7.5 V dc.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
3. The total number of these products when interconnected is not to exceed a total of 14 feet or 14 "ThinLED" units per Class 2
circuit. These products are not to draw a total wattage of greater than thePsecondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from weather.
Class 2 power supply, Model LED Outline Lighting Systems "FlexiBRIGHT", Cat. No. 701499-X-Y, where X and Y may be any
alphanumeric character.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2,12 volt DC power source or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
3. These products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply ber Class
2 circuit.
4. These products are provided with wire soldered on the printed wiring board forconnection.
5. These products are suitable for use in dry, damp and wet locations.
Class 2 LEDs, Modules designated, "LED STRIPE2 (Border Light)" and "701'956-XXXXXX" series, where XXXXXX may be
replaced with alphanumeric characters.
1. These pnoducts are only suitable f0r connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power soufce.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
3. Class 2 LEDs, "LED STRIPE2 (Border Light)", is rated max. 48 Watts per module. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the;Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
Class 2 LED Module, Cat. No. 701269-xxxxxxxxxx-MB Series, where x)00000xxx may be blank or any alphanumeric charatters
1. These products have been'evaluated only for use when connected to the Class 2 output of a Listed or Recognized power
source rated 15 VDCor less.
2. These products are suitable for lise in dry, damp and wet locations with supply sources rated at 15 VDC or;less.
3. These products are not required to be enclosed or protected from the weather in 'the end product.
4. These products may be secured in the end product with any available means.
5. These p, oducts are rated for a maximum of 7.5 watts or less per module.
Class 2 LED Border Light, Class 2 "Border Light", Cat. No. 701 189-XXXXXXXXXX series.
October 1, 2013 SIGN COMPONENTS MANUAL (SAM)134
1. These products are only suitable for connection to a Class 2 power source, rated 30 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 30 V DC.
3. These products are each rated max. 100 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations when rated maximum 30 VDC.
5. These products are not required to be enclosed or protected from the weather in the end product when rated 30 VDC or less.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
LED Strips, Cat. No. 701174,701181 and 701i195 with suffix -R, -Y, -A, -B, -W or -G followed by -1" through -24"
1. These products are only suitable for connection to a UL Listed or Recognized Class 2,24 volt AG power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
3. These products may be cut into segments through a black mark provided on the printed wiring board. No other cut across the
board is permitted.
4. Cat. No. 701174 is rated for 4.2 watts per foot, Cat. No. 701181 is rated for 9.2 watts per foot and Cat. No. 701195 is rated at
1.5 Watts per' foot. T.he total number of feet of each type and inches for the inch unit are nbt to produce a total wattage of
greater than 60 watts per Class 2 circuit.
5. These products are suitable for use in dry, damp and wet locations.
6. These products are not required to be enclosed or protected from weather.
Class 2 LED Module, Cat. No 701946-XXYYYYYYZZZ series, where XX, YYYYYYand ZZZ may be replaced with any
alphanumeric characters or blank.
1. These products are suitable for use in dry, damp and wet locations and supplied only with a Class 2 power source rated 24 Volt
DC or less.
2. When units are connected toia Class 2 circuit, they are not to draw a total wattage of'greater than the secondary or output rating
of the Class 2 supply,
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the endl product by any means available.
Class 2 power supply. Model 701285.
1. Power supply is intended to power LEDs in signs.
2. Power supply model is intended for permanent connection only.
3. These units are suitable for use in dry location without a need for an additional endlosure and in damp locations when installed
inside a sign that complies with the Exclusion of Water Test in UL 48.
4. If the power supply output wiring is extended longer than the 5 foot leads provided, the spliced connections shall be made
inside a Listed junction box suitable for the application included with proper grounding.
Class 2 power supply: Cat. Nos. 701349, 701351.
1, Power supply models 701349 and 701351 are intended to power LEDs in signs.
2. Power supply model 701349 and 701351 are intended for permanent connection only
3. These units are' suitable for use In dry location without a need for an addjtional enclosure and in damp locations when installed
inside a sign that complies with the Exclusion of Water Test in UL 48.
5. These power supplies have two outputs. The Class 2 output circuits are riot to be conductively connected to each other in the
sign by wiring or other type of component.
6. The maximum rated output power for Model 701349 is 42 watts at each Class 2 output. The maximum rated output power fof
Model 701351 is 60 watts at each Class 2 output.
Class 2 power supplies, Models 701507-MOD, 701507-MOD277 (800603277/347-SLN). All may be followed by alphanumeric
suffix.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class
2 Output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp -and wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacihg to top of enclosure.
4 When used in wet locations, each unit shall be provided with Listed (QCR\,9 1/2 inch, liquid tight conduit fittings oh primary
circuit.
5. When used in a cord connected product. the need for conducting a leakage current test shall be considered in the end product.
6. When not marked for Dry and Damp Locations Only the power supply primary bracket shall be provided with min. 3.5 threads
and maximum 5 threads tapered for connection lo liquid tight conduit fitting. If less than 3. 5 threads, the liquid tight shall be
provided with watertight fitting Listed (QCR\,9 1/2 inch, liquid tight conduit fittings.
7. The suitability of grounding connection shall be determined in the end-use product.
Class 2 power supply, Model 701680.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only
5. Strain Relief on input lead construction and Impact Tests have not been investigated.
6. The polymeric enclosure of each unit has riot been evaluated as ultimate enclosure. The flame class of pelymeric enclosure of
each unit is V-2, and the necessity of additional fire barriers shall be determined in end product.
7. Multiple power supplies shall be spaced at least 25mm (1 in.) end to end or 102min (4 in.) in other directions. If lesser spacings
are used, then the Temperature Test shall be conducted in the end use product. For reference the maximum enclosure (case)
temperature on Ihe power supply was 90°C when tested at 58.4° ambient.
Class 2 power supply, Model 701680-MIW,
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class.2
output.
135 SIGN COMPONENTS MANUAL (SAM)October 1,2013
2. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and
wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacihg to top of enclosure.
4. These products are provided with the following electrical ratings:
Input Output
|Model Vac A Hz Vdc A
701680-MW | 100-240 055 50/60 12 1.67
5. These products shall be enclosed in the end product.
6. These power supplies are suitable for use in dry and damp locations.
Class 2 power supply, Model 701681.
1. The product shall be installed in compliance'with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. Input leads are Style 1015. No. 18 AWG, rated VW-1,600 V. 105°C. Output leads are Style 1430, No. 18 AWG, rated VW-1,
300 V. 105°C. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief and Impact Tests have not been investigated on input lead construction. The suitability of the enclosure as ultimate
enclosure shall be determined in the end-use application.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame classj of the polymeric enclosure
is V-0 and the necessity of additional fire barriers shall be determined in end product.
7. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
Class 2 power supplies, Model 701495.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of four Class 2
outputs.
2. These power supplies are only suitable for use in dry, damp and wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing t0 sidewalls,
and minimum 2 inches spacing to top of enclosure.
Class 2 power LED Lighting Strip, 701912-QQXXYYZZZ series, where QQ represents length, XX represents the LED color
temperature, YY represents configuration and ZZZ represents the LED drive current.
1. These products are only suitable for connection to a Class 2 power source, rated 24VDC.
2- These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage;
and energy limits and which is rated greater than 24VDC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated class 2.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or Outline lighting, the need te conduct a temperature test shall
be considered.
Class 2 "Dimming Control Knob" potentiometer, Model 701843.
1. These products afe only suitable for connection to the output of a UL Listed or Recognized Class 2 power supply rated max 12
VDC.
2. These products are suitablefor use in dig, and damp locations.
3. These products are suitabla for factory wiring only.
4. These products are 1 Kohm potentiometers intended for connection to max 12 VDC Class 2 power supply that drops the voltage
to a 0-10 V signal to feed into the PWIVI dimmer.
Class 2 LED Modules, Cat. No. 701960-XXYYYZ Series, where XX, YYY, and Z maybe replaced with anyialpbanumeric
character or blank.
1. These products are suitable for use in dry, damp and wet locations aAd supplied only with a Classj 2 power source rated, 24 Volt
DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
Class 2 power supplies, Models 701507-60W1-JV and 701507-60W1-CT.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Output Output
Frequency Voltage Current
Model Number Input Voltage (\4 Input.Current (A)(Hz):(\/dc)(mA)
701507-60W1-JV 100L240 0.85 50/60 12 0-500
70 1 507-60W1 -CT
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and 101.6 mm (4 in) from side to side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factor'y wiring only.
6. These products are intended for use in a dry or damp locationsonly.
7. The suitability of input/output leads and the wring shall be determined in end product use.
SPARTECH PLASTICS E202184
PASTELERIA
LUCASO-SIGNS
-LLC
1101 S. Grand Avenue Suite C Carrera 68 813-42
Santa Ana, CA 92705 USA Bogota, D.C ColombiaRANCHO LA ILUSION +1 (714) 542 3780 +57 (1) 290 6411
salfs@lucasosigns.com
LULLILLI.lucasosigns.com
www.Ezboxsyst€m.com
ProjEct:
Past€I€ria Rancho La Ilusion
Addr€ss:
1247 Main St, Santa Ana CA 92707 1247 Main St, Santa Ana CA 92707
Account Manag€r:
Juan Ospina / Lic. # 974657
le o0 Q E
/8 9£ Mcfadden Ave69 8 loo ·b, * 9 Haiwood PI ,0 b - ·8 =5
Scale: As Not€d
Design: # 20130226
alO 7-
<
9 8 2 Date: August 14th 201331
m Libra One P
Gle,idale Ct
IE Mcfadden Ave
SHARPI€ OR SIMILAR
4DU 3 PLEASE USE PERMANENT MARKER
e *mLathrop 0S Intecmediate
School Approvals:APPROCE:11 - 'For Job Landlord/OulnEr- W LL'-
W Russell Ave WRI Ave o PLANNING DIViSION Name: AGetC 7->02-'CO 200 1 0 E Ausset |
- r, - -
, 0 2 , kem . a E R* 0 3 - MASTER I.D.-.2213=1£25.2931 1, 4 05 00 2 0 0 0,1
-f 4/Im e 500 14 Zonet.5.0_IN G.P G.C
3 Santa e0 4 viwbd St [Oxford St I.
AralBO :00 -*- E ' PLANNE R1-__ DATE 'For Installation lo /, -5/13Griffi.
Name:
TRANSFERRED BY DATE
A
W Wilshire Ave _
200 ,0 EW,ishiulCalifornia 2
Denlistry-Santa •Allied h - _
0 .
Ana •Rent A CarLf0 4
i
B HOA,1 St Hobert St E Ho]bart E
Service - i tood •'00 200 0
Damage Repair Eo
St Anne Y L.
School ,0
-U
St Anne @
by Sir.gleton Church '' 0 E Borch
1- V€cinity Map
Scal€: NTS
\/4
PLANNING INSPECTION REQUIRED: Signature:...•I IGUGH_ FINAL- NONE
NAME_ _(714) -_.This is an Original Unpublish€d drawing
crcat€d by LUCASO SIGNS. It is
RETAIN PLANS FOR FUVURE REVISK) submittcd for your approval , it is not to
SUBJECT TO :TEMS CHECKED AND (-be shown to anwon€ outsid€ of yourBELOW:organization nor is it to b€ r€produc€d,O IN-f:li-:1·OR TION:copied or exhibitcd in any fashion. Th€Fl / III,#: -• &.I
changing of colors, sizfs materials or?CR/\TIONS/MODT
O A.L. 0 ..TER; 3...1 -O I.ATCH EXISTI, ·illumination mcthod dofs not altEr th€O 9(:REHENINS REQU:,dED
O SUBMIT LANDSCAPE PLANS d€sign Own€rshipof thisd€signis held by
LUCASO SIGNS. Authorization to use this
CONDITIONS: 4 f 2-0 13 -10 7 designinany fashion must be obtained in
U>4 t| -rt)<'writing from LUCASO SIGNS.
NOTE: The colors d€pict€d h€r€ a rE a
Graphic reprfs€ntation. Actual color may
varg.SEE colorspecifications.
-Af-121111-2-1-
B
LAC
LUCBSO-SIGNS
1
-t
4
4T
t
4/
j -r
1101 S. Grand Avenue Suit€ C i Cappera 68 8 8,42
Santa Ana, CA 92705 USA Bogota, D.C Colombia+1 (714) 542 3780 +57 (1) 290 6411
sales@lucasosigns.com
ujuiw.lucasosigns.com
wium.€zboxsyst€m.com
ProjEct:
Past€lelia Rancho La Ilusion
Addr€ss:
1247 Main St, Santa Ana CA 92707
Account Manag€r:
Juan Ospina / Lic. # 974657
Scale: As Not€d
Design: # 20130226
Dat€: August 14th 2013
PLEASE USE PERMANENT MARKER
SHARA€ OR SIMILAR
Approvals:
• For Job Landlord/Own€r
Nam€:T Ft CLA/bL
Signature: -
N •For Installation
Name:
Signatur€:
Proposed Wall Sign
1- Plan
Scal€: NTS
1247 Main St, Santa Ana CA 92707
This is an Original Unpublish€d drawing
cr€ated by LUCASO SIGNS. It is
submitt€d for your approval, it is not to
b€ shown to anyon€ outsid€ of gour
organization nor is it to b€ reproduced,
copied or exhibit€d in any fashion. Th€
changing of colors, siz€s mat€rials or
illumination m€thod does not alt€r the
d€sign Own€rshipof thisd€sign ish€ld by
LUCASO SIGNS. Authorization to us€this
design in any fashion must b€ obtained in
writing from LUCASOSIGNS.
El 4 NOTE: Th€ colors d€picted her€ are a
Graphic rfpr€sEntation. Actual color may
vary.S€€ colorsp€cifications.
J
46'-7"
16'-7"
8'-4"
LLC
LUCASO-SIGNS
Santa Ana, CA 92705 USA Bogota, D.C Colombia
1101 S. Grand Avenue Suit€ C I Carr€ra 68 813-42
4'-5"+1 (714) 542 3780 +57 (1) 290 6411
saIEs@lucasosigns.com
www.lucasosigns.com
www.ezboxsustcm.com
0'-9"
4'-5"
PASTELE!tia -------
RANCHO LA ILUSION
PrOjECt:
Past€1€ria Rancho La Ilusion
Address:
1247 Main St, Santa Ana CA 92707
Account Manager:
Juan Ospina / Lic. # 974657
Scal€: As Not€d
9'-10"
Design. # 20130226
Dat€: August 14th 2013
PLEASE USE PERMANENT MARKER
SHARAE OR SIMILAR
Approvals:
1- NorthW€st Building El€vation
Scal€: 1/55.21
DESCRIPTION Total Sign Area: 205.90 Sqf.
Max Sign Ar€a Allou,€d: 82.36 Sqf (40%)
Max Sign Length Allow€d: 34.94' (75°/01
Sign: 29.01 Sqf.
• For Job Landlord/Oulne
Nam€:
Signature:
RANCUO LA ILIJSION
1- Photo Vi€uu
Scal€: NTS
•For Installation
Name:
Signature:
This is an Original Unpublish€d drawing
cr€ated by LUCASO SIGNS. It is
submittfd for your approval, it is not to
b€ sholun to anwon€ outsid€ of your
organization nor is it to b€ r€produced,
copi€d or Exhibit€d in any fashion. Th€
changing of colors, siZES mateials or
illumination method docs not alter th€
design Ownership of thisdesign is held by
LUCASO SIGNS. Authorization to us€ this
design in any fashion must b€ obtaincd in
uMiting from LUCASO SIGNS.
NOTE: ThE colors depicted heE ar< a
Graphic represEntation. Actual color may
vary. SEEcolorsp€cifications.
.
44
16'-7"
LLC
4 LUCASO-SIGNS8'-4"1101 S. Grand Avenue SuitE C i Cappera 68 B 13-42
9 Santa Ana, CA 92705 USA Bogota, D.C Colombia+1 (714) 542 3780 +57 (1) 290 6411
PAS 6' E LE Rill sal€s@lucasosigns.com
luuiul.lucasosigns.com
lululu.€Zboxsyst€m.comPanton€ 355 C
or similar
ProjEct:
' RANCHO LA ILUSION Past€I€ria Rancho La Ilusion
Address:
1247 Main St, Santa Ana CA 92707
Panton€ 485 C
or similar
Account Manager:
Juan Ospina / Lic. # 974657
SIGN ELEVATION /SQUARE FEET
QUANTITY: ONE (1) SET REQUIRED
5" 1"
0.040 aluminum
channel letter.
3M ® Double Side Tape ,-7,-Ittt
Outdoor to bond Modules IlletU *1
LED Modules three bulbs 11 +4-11
6500 K White Color UL Listed 4 44
MEI
3/16" Thick PMMA (Acrilyc)11 +4-442 14
Black Out Solid Color 444
111=
3/16" Thick Lexan ®9=
Clear Back
Rigid Couplings R E
Conduit Nipples
1" Trim Cap Black
Weep Holes -
1/4" Aluminum Spacing
16.56 SQF
SCALE: 1/13.66
LED UL LISTED: 58'
170 Modules
81.6 Watts /
1.46 Amp
Two Transformers:
One 60 Watts
One 35 Watts
LED BRAND: SLOAN Apollo Model 701269-W6-
Flexible MB
Conduit POWER SUPPLY: SLOAN Model IP68
LED SWITCH
/ Power Supply /g DISCONNETOR
i U L Listed /
Secondary
/12 Volt
110 VoltL___3 -Primary
UL Listed Typical section D€tailStraight
Connector Transformer
Female M"Box Scal€: NTS
Threaded
Pipe Conduit
•L€TT€RS: Chann€I
1€tt€rs,black trim cap, black
returns LED syst€m uncle
ULCod€.
• FACES: PMMA 3/16"
Thick Fac€s translucent
•RETURNS: 0.040
Aluminum can, 5" D€pth
Black color paint€d.
• NOT€: FiEld v€rify all
m€asur€m€nts and
conditions Prior to ang
fabrication.BT
Scale: As Not€d
D€sign: # 20130226
Dat€: August 14th 2013
PLEASE USE PERMANENT MARKER
SHARPIE OR SIMILAR
Approvals:
•For Job Landlord/Own€r
Nam€: AW€,wur 19*2-) G..
Signature: (»
• For Installation
Nam€:
Signatur€:
This is an Original Unpublish€d drawing
cr€at€d bu LUCASO SIGNS. It is
submittcd for your approval, it is not to
b€ shol.Un to anyonc outside of your
organization nor is it to b€ reproduc€d,
copid or exhit:)it€d in any fashion. The
changing of colors, sizes matcrials or
illumination m€thod does not alter th€
dcsign Owneshipofthisd€sign is held bu
LUCASO SIGNS. Authorization to use this
dfsign in any fashion must b€ obtained in
iuriting from LUCASO SIGNS.
NOTE: Th€ colors d€picted h€r€ ar€ a
Graphic r€pr€sentation. Actual color may
varg. Sce colorsp€cifications.
' Cil*.gf-Santa-Ann..53C-St CEC 2010
Minimum (4) screws per letter,
maximum 24" on center, 2"
penetration, #10 sheet metal screws, &
42)_1£_drain holes per [etter
O A local disconnect for the monument sign(s) Isrequired or the dedicated circuit breaker(s) mustbe individually lockable in the off position.
CBG·600 -6Access to any power supply in attic or aboveceiling shall be immediately from a ladder orwith a2x3 foot access door & passage with a12-inch walkway. CEC 600-21 (d)(d)
City of Santa Ana Planning & Building Agency
$PM*·,20#hfl.Mt:,·9?STE4*zrry34€1'75-7.?45*-5*277:„66?t9:141:
ELECTRICAL,
PILAN APPROVAL
This set al plans and specmea·Hons must be kept on Lthe job at a.11 times and it is unlawful to make any
changes or aiterations on same wathout written per- mission from the Department of Building Safety .
Cit' of Santa· Arra.
The approval d Ne Man 7-4 speCE?:Cr';0·33 SHALL NOT..t€. P Sid to Peynitt nor ha an i- : p -·. 21 of the Avioialibir or any proviaione of ANY City Greinance i
or State Law.Approv.=-.3--9-#1=6 ),4-
iITY OF SANTA ANADEPARTMENT OF BUILDING SAFETY &
p PERMrrTYPE:€99./€) PLB
MECH G*ADING
PERMrr# 1(31 192527% 4€11$
OCC. GEC)LII?1
CONSTR. TYPE
CODE EDnnON,52[3 FED
FLOOD ZONE
FLOOD ZONE GERTIE REQ'D YES O
MICROFILM YES Nb)
RADIANT BARRIER @ROOF YES 46
RESIDENTIAL DEV. FEE YEE< NO
SCHOOL DISTRICT YESNO
r.-*.2ae&b*giat*m=L-=fl ..-rL ·r.-5£. »
f
\1
499 tjj -9 U\D 94 9 blay<90 at,8 lou 92*b b C O 1Ut -61 -O(
--