HomeMy WebLinkAbout10181287_3930 S. BRISTOL 106 - PlanPlanning & Building Agency
Building and Safety Division
20 Civic Center Plaza
P.O. Box 1988 (M-19)
Santa Ana, CA 92702
(714) 647-5800
www. santa-ana.orq
ELECTRICAL SIGN
REQUIREMENTS
Code references are to the 2010 California Electrical Code (CEC)
All signs require Planning Department approval.
All electrical signs require electric plancheck and permit.
1. Manufacturer's instructions are required at the time of submittal
C-11: 3-21-2011
2. Submit detailed installation instructions including diagrams to the Building Department
for plan review at the time of submittal. Plans must include appropriate items noted by
this bulletin.
3. Cash or surety bond in the amount of $200.00 is required at time of issuance for each
address. The cash or surety bond will be refunded after all required finals.
A building permit is also required - except for open or highlight neon lighting.
Installation Requirements:
CONTACT FIELD INSPECTOR PRIOR TO SIGN INSTALLATION.
(SEE SECTION G OF THIS BULLETIN)
1. Conductors and equipment shall comply with California Electric Code Article 600.
2. All metal parts of a sign shall be bonded in the manner specified in Article 250. Isolated
metal parts are permitted to be bonded by using an external green insulated conductor.
Equipment grounding & bonding conductors must be sized by 110.26 and protected from
physical damage. Minimum size is 14 AWG. CEC 600.7
3. A listed disconnect switch in the power supply primary, shall be installed within sight of
sign or have permanently installed means for locking in an "OFF" position. This is also
true for a transformer enclosure. CEC 600.6
4. A listed receptacle or an approved termination device shall be used for each neon
electrode. To relieve stress at terminations, tubing shall be supported with listed tube
supports in an approved manner within six inches of electrode connection.
CEC 600.41 & 600.42
5. Every electric sign of any type shall be listed by an approved testing laboratory and shall
be installed in conformance with this listing. That includes "1 of x", "2 of x" labeling for
each separate unit of a multi-unit sign. CEC 600.3
6. All "can" letters and transformers housings shall have section labels that are readily
visible after installation. CEC 600.4
7. Transformers shall be located where accessible and be securely fastened in place.
Page 1 of 2
O 0
m »
When not inside the sign, they need a 3 foot high x 3 foot wide x 3 foot deep workspace.
Transformers are permitted to be located in attics or canopies provided there is a
passageway at least 3 feet high x 2 feet wide with a minimum 12 inch catwalldwalkway
from the point of entry. Transformers must be securely fastened and independent of T-
bar when above a suspended ceiling. No part of sign mav be fed with flexible cord when
located above T-bar ceilings. CEC 600.21(E&F) & 400.8
8. Adequate illumination shall be provided for all working spaces about electrical
equipment. This applies to attics and canopies when entry is required to service or
inspect the equipment. At least one switch is required at entrance. CEC 110.34 & 600.21
9. Doorway to an attic or canopy space shall be minimum 3 feet by 2 feet wide.
CEC 600.21(E)
E. Open neon outline or highlight lighting.
1. To be treated as a sign by this department. However, Section D-5 & D-6 of this bulletin
will not apply.
2. Neon tubing shall be located where not normally exposed to physical damage. Open
neon tubing below 9 feet shall be protected from physical damage by an approved
shielding method. CEC 600.30 and 110.34(E)
F. Light-Emitting Diode (LED) Signs
1. Will be treated as a sign by this department. All sign rules in sections A, B, C, D, F, and
G will apply as appropriate.
2. LED illumination for signage must be a listed or recognized component. Many LED
manufacturers specify particular brands and models of transformers some do not.
Manufacturer information to clarify this issue is required on LED sign plans.
3. Unlisted LEDs may not be used in an electrical sign or as permanently installed
illumination. 110.3
4. Please have packaging or catalog cut-sheets on hand for inspector to review when LED
modules do not bear listing symbols.
G. Inspections
1. Contact an Electrical Inspector one (1) workday (minimum) in advance of installation to
arrange a site meeting on dav of installation.
2. Call for inspection Monday through Friday, 8:00- 8:30 a.m. at (714) 647-5821. Approved
prints and the job card must be on site for inspection.
Page 2 of 2
October 1, 2013 SIGN COMPONENTS MANUAL (SAM)146
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Input Output Output
Input Input Current Power Voltage (\/Output Power
Model No.Voltage 04 Freq (HZ) (A) Factor dc) Current (A) ON)
LCU 060/12 D 120-240 50/60 075 0.95 12 5.0 60
LCU 035/12 D XX 120-240 50/60 0.39 0.95 12 2.92 35
LCU 015/12 D 120-240 50/60 0.35 0.4 12 1.25 15
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and 101.6 mm (4 in) from side to side.
4. These products shall be enclosed in suitable electrical enclosure in the end product.
5. These products are suitable for factory wiring only.
6. The load powered by the Class 2 output of these power supplies at the 12 Vdc rating or less is suitable for use in dry, damp and
wet locations.
7. These products have been tested in oven at 50°C ambient, with the following maximum case temperatures, Tc:
For model LCU 060/12 D the To = 82°C; for model LCU 035/12 D XX the T. = 64°C; for model LCU 035/12 D XX the Tc=74°C.
8. These products are intended for use in a dry or damp locations only.
9. The suitability of inpuUoutput leads and the wing shall be determined in end product use.
10. The metal case of Model LCU 015/12 D is not grounded. The proper grounding means of this product shall comply with the
end product requirements.
Class 2 LED modules, Models P541-CLA, P551-SEL.
1. These products are only suitable for connection to a Class 2 power source rated 14 V DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated at 14 V DC or less.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 14 V DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
TRONICC TECHNOLOGIES E357992
18584 BUDGE
PIERREFONDS, QC H9K1 K8 CANADA
Sign accessories, Class 2 LED modules, 1-T-M-01, TT-M-02, TT-M-03, TT-M-04, TT-B-01.
1. These products were evaluated for connection to a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2
source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limiting requirements.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry and damp locations.
5. Consideration for the installation and power supply connection and interconnection is to be determined in the end-use
application.
TUBE LIGHTING PRODUCTS E348777
1346 PIONEER WAY
EL CAJON, CA 92020
Class 2 LED Strip, Model DSH Series.
1. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated less than 24V DC.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products do not require an electrical enclosure.
5. These products may be secured in place in the end product by any means available.
US LED LTD
6807 PORTWEST DR
E226833
HOUSTON, TX 77024
Class 2 LED Module, Model MY-12-K-XX "MegaX" Series, where Y may be replaced by any number from 0 to 99 incl., K may be
replaced by W, R, B, Y, G or RO and XX is optional, where it may be replaced by any alphanumeric characters (0 to 99 incl. or A
to Z incl. or combinations). .
1. These products are only suitable for connection to a Class 2 power source, rated max 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. These Class 2 LED Modules are each rated 0.77 Watts per unit. When units are connected to a Class 2 circuit, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. When rated
24 VDC, these products are suitable for dry and damp locations only.
5. These products are not required to be enclosed or protected from the weather in the end product.
147 SIGN COMPONENTS MANUAL (SAM)October 1, 2013
LED Accent Module, Mega, Accent or Right Light Series, Model Q ABC-XX-YY-ZZZZ series, where Q may be P, M, AC or blank,
AB, XX and YY may be replaced by any alphanumeric characters (0 to 9 incl. or A to ZZ incl. or combinations), C may be blank
or may be any alphanumeric characters (0 to 9 incl. or A to Z incl. or combinations); and ZZZZ may be any alphanumeric
characters (0 to 9999 incl. or A to zzzz incl. or combinations) or blank.
1. These products are only suitable for connection to a Class 2 power source, rated max 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. These Class 2 LED Modules are each rated 0.77 Watts per unit. When units are connected to a Class 2 circuit, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. When rated
24 VDC, these products are suitable for dry and damp locations only.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Accent LED module, Model AC-X-Y-Z-T, where X is the length of the module, Y identifies the operating voltage, Z identifies
the color, and T identifies a standard.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, max 30 Vdc only power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. These products are not provided with break points in the printed wiring board. No cuts across the board is permitted.
4. These products are suitable for use in dry, damp, and wet locations.
5. These products are not required to be enclosed or protected from weather.
Right Light Series LED module "Right Light", Models TP-2-12-z, abc-X-Y-Z and RLS-X-Y-Z, where X may be any number from 0
to 9, Y may be any number from 00 to 99, and Z may be any alphanumeric character..
1. These products are only suitable for connection to a UL Listed or Recognized Class max. 24 VDC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. These products are not provided with break points in the printed wiring board. No cuts across the board are permitted.
4. These products are suitable for use in dry, damp, and wet locations.
5. These products are not required to be enclosed or protected from weather.
LED Driver Enclosure, Model Life Extender Box.
1. This product has been evaluated for Dry and Damp Locations only. If used in a wet location, Rain Testing shall be conducted
during the end product evaluation.
Class 2 LED Module, Models EXSA-1-6, EXSA-1-12.
1. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated less than 24V DC.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. When rated
24 VDC, these products are suitable for dr'y and damp locations only.
4. These products do not require an electrical enclosure. The 24Vdc modules require protection from the weather in the end
product, as they are not suitable for wet locations. The 12Vdc modules require no such protection.
5. These products may be secured in place in the end product by any means available.
Class 2 LED Module, Models Tandem XX and Tandem XX Dual, where XX, a non-safety related designation, may be any
alphanumeric character.
1. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated less than 24V DC.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 VAC or 30 V DC max.
4. These products do not require an electrical enclosure.
5. These products may be secured in place in the end product by any means available.
Class 2 LED Module,"BEl" series, designated as Models BEl-W-XY-ZZ series, Where W may be any number from 0 to 9, X may
be any number from 0-9, Y may be L or Hand ZZ may be any two digit number between 0-9.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2 power source with max. 24 VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. These products are provided with break points in the printed wiring board. No cuts across the board are permitted except where
indicated in the installation instructions.
4. These products are suitable for use in dry, damp, and wet locations.
5. These products are not required to be enclosed or protected from weather.
6. These products may be secured in place in the end product by any means available
UNILUMIN GROUP CO LTD E330828
BLDG A, 112 YONGFU RD
QIAOTOU, FUYONG TOWN
BAOAN DISTRICT
SHENZHEN, GUANGDONG 518103 CHINA
Changing Message Signs, Model P16.
1. Maximum of 2 units when installed in a 15 Amp branch circuit and 3 units for a 20 Amp branch circuit.
2. This product was tested for use at a room ambient temperature of 25°C. Testing was conducted on an open bench positioned in
a vertical position facing horizontally. The need for conducting temperature testing in the end product shall be considered where
the units are installed in a higher ambient,
3. The suitability of the mounting means shall be determined in the end use.
3 0
0 03- i--0 - 4
--020- -.*
45 00 1
is
C/)
60
required or the dedicated circuit breaker(s) musbe illdividually lockable In the off position.O A local disconnect for the monument sign(s)
pED 600-6 ply in al0 00 ceiling shall be immediately from a ladder or00 0 Access to any power sup ic or above
12City of Santa Ana Planning & Building AgencyI with 82x3 foot access door & passage with a-inch walkway. CEC 600-21 (d)(d)
City of Santa Ana, CBC & CEC 2013
Minimum (4) screws per letter,
maximum 24" on center, 2
penetration, #10 sheet metal screws, & (2) 44" drain holes per letter j
»21=
ELECTRICAL
j PLAN APPROVAL
This set of plans and speclfications must be kept ont job at all times and It Is unlawful to make any4/anges or alterations on same without w,ltten per-
mission from the Department of Building Safety1 City of Santa Ana.
The approval of this plan and speclfications SHALL
NOT ba. held to permit nor be an approval of theviola{.1.0.reM5r any provisions of ANY City Ordinanceor Stabiaw
4,4»29=444
ITY OF SANTAANADEPARTMENT OF BUILDING SAFETY
l i
.1.
1
' PERMIT TYPE:d%,*f@ PLBG MECH GBADING
PERMIT#102 162 29 /
OCC. GROUP ,%20152% 9 32
CONSTR.TYPE
CODE EDITION 20)33
FLOOD ZONF
FLOOD ZONE CERTIF. REQ'D YES
MICROFILM YES j
RADIANT BARRIER @ ROOF YES
RESIDENTIAL DEV. FEE YE6
SCHOOL DISTRICT YES NO \4.. 1
C.42
9
NO
0
4/47"b=
lo
bo
A
+ 10*
31' - 5"
FASCIA
¢S6NES SIGN
TEL: 858-569-1400 FAX: 858-569-1453
9025 BALBOA AVENUE, STE 150
SAN DIEGO, CA 92123-1520
CLIENT NAME:
JIMMY JOHNS
ADDRESS:
3930 SOUTH BRISTOL STREET
SANTAANA, CA92704
SALES PERSON:
JOHN PANUZZO
DESIGNER:
LMPope
DATE:
FEBRUARY 5, 2014
- CLIENT APPROVAL: -
[ JOB #200868 - 93258
(*IKNIB{R:Ii*Ki)
/.9
4
4 i e. br &
3 =-0 -1-7
3'- 6"
lair-
C213
...
PRIMARY ELECTRICAL TO SIGN LOCATIONS
IS TO BE PROVIDED BY OTHERS. 20 AMP
DEDICATED CIRCUITCS) WITH NO SHARED
NEUTRALS AND A GROUND RETURNING TO
THE PANEL IS REQUIRED FOR ALL
INSTALLATIONS.
COLORS REPRESENTED IN THIS DRAWING
ARE FOR PRESENTATION PURPOSES ONLY.
THEY MAY NOT MATCH YOUR ANISHED
PRODUCT PERFECTLY. COLOR CALL-OUTS
ARE FOR AMATCH AS CLOSE AS POSSIBLE.
THIS ORIGINAL DESIGN IS THE SOLE
PROPERTY OF UORASIGNS. IT CANNOT BE
REPRODUCED, COPIED OR EXHIBITED IN
WHOLE OR PART, WITHOUT FIRST
OBTAINING WRITTEN CONSENT FROM
ULTRASIGNS.
THIS SIGN IS INTENDED TO BE INSTALLED IN
ACCORDANCE VmH THE REQUIREMENTS
OF ARTICLE 600 OF THE NATIONAL
ELECTRICAL CODE AND/OR OTHER
APPUCABLE LOCAL CODES. THIS INCLUDES
PROPER GROUNDING AND BONDING OF THE
SIGN.
REVISIONS:
A
m
m
C, 0,
6.7 97
VOLTAGE:
120 VOLT - VERIFY
(RSiIRmlii){RK@*Bo@11§0&1)17[#97(mIN!,QI*All*ljo#NOIDIBil@(t SKETCH NUMBER:
JIMMYJOHNS02
PAGE:5 oF 7
1 -
i
.
9 NESSIGN
TEL: 858-569-1400 FAX: 858-569-1453
9025 BALBOA AVENUE, STE 150
SAN DIEGO, CA 92123-1520
CLIENT NAME:
JIMMY JOHNS
1/8" #7328 WHITE ACRYLIC
FACES. FIRST SURFACE -
DECORATED
.063" THK. ALUM. BACKS
THICKER BACK REQ'D. -
FOR MOUNTING TECH.
5'DEEP 7"
1/8" THK. ROUTED
ALUMINUM BKGRD.
PANEL
ADDRESS:
3930 SOUTH BRISTOL STREETf -SANTAANA, CA 92704
- SALESPERSON:
.040" x 5" ALUM.
RETURNS (LETTER LOK)
.040" x 5" ALUM.
RETURNS (LETTER LOK)
1/8" #7328 WHITE ACRYLIC
FACES w/ BLACK 3M VINYL -
OPAQUE BORDER
DATE:
FEBRUARY 5, 2014
JOHN PANUZZO
DESIGNER:
3M" JEWEL UTE TRIM CAP -3/4" JEWEL LITE TRIM CAP -
LMPope
r x 7»ALUM. TRANS. BOX
.063" THK. ALUM. BACKS
THICKER BACK REQ'D. -
FOR MOUNTING TECH.70 x 7» x 18' GALV. TRANS. BOX
CLIENT APPROVAL:
JOB #200868 - 93258
Bi
#10 x 3" SCREWS &
BLUE ANCHORS ,
WH!TE LED ILL.UM. -
I' . ---
... e:ATTACHEDJO LETTER -
5"DEEP
M
WHITE LED ILLUM.
ATTACHED TO LETTER
BACK PER UL REQ.
7,970!Ah.ELECTRICAM ....
PRIMARY ELECTRICAL TO SIGN LOCATIONS
IS TO BE PROVIDED BY OTHERS. 20 AMP
DEDICATED CIRCUIT(S) WITH NO SHARED
NEUmALS AND A GROUND RETURNING TO
THE PANEL IS REQUIRED FOR ALL.
INSTALLAT]ONS. :-4
3442.
I.
BACK PER UL REQ.
POWERSUPPLY.&·
TRANSFORMER BOX w/
ON-OFF TOGGLE SWITCH
1
i 25*h J
'*,-·11.
Itt=fl
1 · PASS.THRU. :
POWER SUPPLY &
7 --'-TRANSFORMER BOX W/»« ·
ON-OFF,TOGGLE SWITCH -
COLORS REPRESENTED IN THIS DRAWING
ARE FOR PRESENTATION R:RPOSES ONIA'
-THEY.MAY NOT· MAEH -YOUINFINISHED
PRODUCT PERFECTLY COLOR CALL-OUTS
AREFORAMATCHASpLOSEASPOSSIBLE.
lM" DIA. WEEP HOLES
(2) PER LETTER w/.040" ALUM.
LIGHT BAFFLE AS SHOWN 1
#10 x 3" SCREWS &
BLUE ANCHORS
#10 PAN HEAD SCREWS
lM" DIA. WEEP HOLES
(2) PER LETTER w/.040" ALUM.
LIGHT BAFFLE AS SHOWN
/AE,9„1 TYR SECTION DETAIL -
SCALE: 3"=1'-0"
THIS ORIGINAL DESIGN IS THE SOLE
PROPERTY OF ULIRASIGNS. IT CANNOT BE
REPRODUCED, COPIED OR EXHIBITED IN
WHOLE OR PART, WITHOUT FIRST
OBTAINING WRITTEN CONSENT FROM
UORASIGNS.
#10 PAN HEAD SCREWS -
ELECTRICAL WHIP
TO BE SUPPLIED BY GC
GROUND SCREW DETAIL
THIS SIGN IS INTENDED TO BE INSTALLED IN
ACCORDANCE WITH THE REQUIREMENTS
OF ARTICLE 600 OF THE NATIONAL
ELECTRICAL CODE AND/OR OTHER
APPLICABLE LOCAL CODES. THIS INCLUDES
PROPER GROUNDING AND BONDING OF THE
SIGN.
TYR SECTION DETAIL - LOGO & LETTERS LOGO & LETTERS
SCALE: 3"=1'-0"
REVISIONS:
(77 40
b, Ck
b, rk
fi) 6)
(?7 07
VOLTAGE:
120 VOLT - VERIFY
1&(ililii)iii*ifmxl
March 4, 2014
SKETCH NUMBER:
JIMMYJ0HNS02
PAGE:7 oF 7
h
C.JONES SIGN
TEL: 858-569-1400 FAX: 858-569-1453
9025 BALBOA AVENUE, STE 150
SAN DIEGO, CA 92123-1520
CLIENT NAME:
JIMMY JOHNS
ADDRESS:
3930 SOUTH BRISTOL STREET
SANTAANA, CA 92704
16'-0" OA STRETCH OUT 5"DEED SALES PERSON:
2'-0" LOGO ,6-1/2",13'-5-1/2" STRETCH OUT JOHN PANUZZO
L -1-L J-L
OO
r 111
1 1
-J-BID
(
..'
0 - '43,
2-0" LOGO
DESIGNER:
LMPope
DATE:
FEBRUARY 5, 2014
CLIENT APPROVAL:
JOB #200868 - 93258
6
r
3
1-I
445 LED:ILLUMINATED.EHANNELLOGO-&.LETTERS
32.00 SQUARE FEET-4.2
f LD
1 PRIMARY ELECTRICAL TO SIGN LOCAnONS
IS TO BE PROVIDED BY OTHERS. 20 AMP
DEDICATED CIRCUIT(S) WITH NO SHARED
NEUTRALS AND A GROUND RETURNING TO
THE PANEL IS REQUIRED FOR Al.L*ki
INSTALLATIONS.
- COLORS REPRESENTED IN THIS DRAWING
ARE FOR PRESENTAnON PURPOSES ONLM
SIDE VIEW -'THEY. MAY NOT MATCH YOUS FINISHED
- PRODUCT PERFECTLY COLOR CALL-OUTS
ARE FOR A MATCH AS CLOSE AS POSSIBLE.
SPECIFICATIONS (CHANNEL LOGO & LETTERS)
LOGO
FACES: 1/8" THK. WHITE ACRYLIC w/ 1/2" BLACK VINYL BORDER
RED VINYL TO MATCH PMS #186
RETURNS: 5" DEEP .040" THK. ALUMINUM, PRE-FINISHED BLACK
TRIM-CAP: 3M" BLACK
LED's: US LED, PNT-3-12-W
MOUNTING: LETTERS MOUNTED TO EXISTING WALL w/ #10 SCREWS
& BLUE ANCHORS. EXACT METHOD TO BE DETERMINED IN FIELD.
LETTERS
FACES: 1/8" THK. WHITE ACRYLIC. FIRST SURFACE BLACK OPAQUE &
RED VINYL TO MATCH PMS #186
RETURNS: 5" DEEP .040" THK. ALUMINUM, PRE-FINISHED BLACK
TRIM-CAP: 3M" BLACK
LED's: US LED, PNT-3-12-W
MOUNTING: LETTERS MOUNTED TO EXISTING WALL w/ #10 SCREWS
& BLUE ANCHORS. EXACT METHOD TO BE DETERMINED IN FIELD.
THIS ORIGINAL DESIGN IS THE SOLE
PROPERTY OF UURASIGNS. IT CANNOT BE
REPRODUCED, COPIED OR EXHIBITED IN
WHOLE OR PART, WITHOUT FIRST
OBTAINING WRITTEN CONSENT FROM
ULTRASIGNS.
THIS SIGN IS INTENDED TO BE INSTALLED IN
ACCORDANCE WITH THE REQUIREMENTS
OF ARTICLE 600 OF THE NATIONAL
ELECTRICAL CODE AND/OR OTHER
APPLICABLE LOCAL CODES. THIS INCLUDES
PROPER GROUNDING AND BONDING OF THE
SIGN.
REVISIONS:
Ck d,
m
b, rk
m ®
(0 97
VOLTAGE:
120 VOLT - VERIFY
mm;EmE,
March 4, 2014
SKETCH NUMBER:
JIMMYJ0HNS02
PAGE:6 of 7
NES SIGN
TEL: 858-569-1400 FAX: 858-569-1453
9025 BALBOA AVENUE, STE 150
SAN DIEGO, CA 92123-1520
CLIENT NAME:
JIMMY JOHNS
ADDRESS:
3930 SOUTH BRISTOL STREET
SANTA ANA, CA 92704
10'-4" OA STRETCH OUT 5" DEEP„ 7" RCWY.,SALES PERSON:4 ,
0,
it
15" LOGO 1-1(4"„318" 14-1/4" 3/8 , 111/4" 11-314" "J" 1,121"
15" LOGO 4" 8'-9" STRETCH OUT , JOHN PANUZZO
R ,
DESIGNER:
LMPope
DATE:
FEBRUARY 5, 2014
.
CLIENT APPROVAL:
JOB #200868 - 93258
SIDE VIEW--
PRIMARY ELECTRICAL TO SIGN LOCATIONS
IS TO BE PROVIDED BY OTHERS. 20 AMP
DEDICATED CIRCUIT(S) WITH NO SHARED
NEUmALS AND A GROUND RETURNING TO
THE PANEL IS REQUIRED FOR ALL
INSTALLATIONS.
hiERA FRONT v LED ILLUMINATED CHANNEL LOGO & LETTERS ON RACEWAY
13.00 SQUARE FEET-. -4 .
VIEW -
El'-0"
COLORS REPRESENTED IN THIS DRAWING
ARE FOR PRESENTATION PURPOSES ONIX
f THEY MAY NOT MATCH YOUR' FiNISHED
PRODUCT PERFECTLY COLOR CALL-OUG
) ARE FORA MATCH AS CLOSE AS POSSIBLE.
SPECIFICATIONS (CHANNEL LOGO & LETTERS)
LOGO
FACES: 1/8" THI<. WHITE ACRYLIC w/ 1/2" BLACK VINYL BORDER
RED VINYL TO MATCH PMS #186
RETURNS: 5" DEEP .040" THK. ALUMINUM, PRE-FINISHED BLACK
TRIM-CAP: 3/4" BLACK
LED's: US LED, PNT-3-12-W
BACKGROUND: 1-1/4" CONTOUR - 1/8" THK. ROUTED ALUMINUM, PTM BLACK
RACEWAY: 7" x 7" FAB. ALUMINUM, PAINTED BLACK
MOUNTING: RACEWAY MOUNTED TO EXISTING WALL w/ 3/8" DIA.
TOGGLE BOLTS OR LAGS & SHIELDS. EXACT METHOD TO BE
DETERMINED IN FIELD.
LETTERS
FACES: 1/8" THK. WHITE ACRYLIC. FIRST SURFACE BLACK OPAQUE &
RED VINYL TO MATCH PMS #186
RETURNS: 5" DEEP.040" THK. ALUMINUM, PRE-FINISHED BLACK
TRIM-CAP: 3M" BLACK
LED's: US LED, PNT-3-12-W
BACKGROUND: 1-1M" CONTOUR - 1/8" THK. ROUTED ALUMINUM, PTM BLACK
RACEWAY: 7" x 7" FAB. ALUMINUM, PAINTED BLACK
MOUNTING: RACEWAY MOUNTED TO EXISTING WALL w/ 3/8" DIA.
TOGGLE BOLTS OR LAGS & SHIELDS. EXACT METHOD TO BE
DETERMINED IN FIELD.
THIS ORIGINAL DESIGN IS THE SOLE
PROPERTY OF ULTRASIGNS. IT CANNOT BE
REPRODUCED, COPIED OR EXHIBITED IN
WHOLE OR PART, WITHOUT FIRST
OBTAINING WRITTEN CONSENT FROM
ULTRASIGNS.
THIS SIGN IS INTENDED TO BE INSTALLED IN
ACCORDANCE WITH THE REQUIREMENTS
OF ARTICLE 600 OF THE NATIONAL
ELECTRICAL CODE AND/OR OTHER
APPLICABLE LOCAL CODES. THIS INCLUDES
PROPER GROUNDING AND BONDING OF THE
SIGN.
REVISIONS:
0 97
0 0
m
m m
6.7 07
VOLTAGE:
120 VOLT - VERIFY
17initimm"TION-,
March 4, 2014
SKETCH NUMBER:
JIMMYJ0HNS02
PAGE:4 oF 7
t
t
r
EXISTING PHOTO
IONES SN
TEL: 858-569-1400 FAX: 858-569-1453
9025 BALBOA AVENUE, STE 150
SAN DIEGO, CA 92123-1520
CLIENT NAME:
JIMMY JOHNS
ADDRESS:
3930 SOUTH BRISTOL STREET
SANTAANA, CA 92704
SALES PERSON:
JOHN PANUZZO
28' - 0" : DESIGNER:
···1 7...
4' 1 0"
FASCIA
$6.
1
l
I I IVIMY OH N S
r
t
PROPOSED PHOTO - SIGN'1.1 NEW EAi;ETTERS - 3.00 SQ. FT.
LMPope
DATE:
FEBRUARY 5, 2014
CLIENT APPROVAL:
JOB #200868 - 93258
Is To BE PROVIDED BY OTHERS. 20 AMP
PRIMARY ELECTRICAL TO SIGN LOCATIONS
NEGRALS AND A GROUND RETURNING TO
DEDICATED CIRCUIRS) WITH NO SHARED
E..·50>.., 5 Ag/4 =dr4. .3.,M .43-5.: -. c; : THE PANEL IS REQUIRED FOR ALL
INSTAUATIONS.
COLORS REPRESENTED IN THIS DRAWING
ARE FOR PRESENTATiON PURPOSES ONLY
'THEY.MAY NOT MATCH YOUR · FINISHED
PRODUCT PERFECTLY. COLOR * CALL-OUTS
ARE FOR A MATCH AS CLOSE AS POSSIBLE.
THIS ORIGINAL DESIGN IS THE SOLE
PROPERTY OF UURASIGNS. IT CANNOT BE
REPRODUCED, COPIED OR EXHIBITED IN
WHOLE OR PART, WITHOUT FIRST
OBTAINING WRITTEN CONSENT FROM
UCmASIGNS.
THIS SIGN IS INTENDED TO BE INSTALLED IN
ACCORDANCE WITH THE REQUIREMENTS
OF ARTICLE 600 OF THE NATIONAL
ELECTRICAL CODE AND/OR OTHER
APPLICABLE LOCAL CODES. THIS INCLUDES
PROPER GROUNDING AND BONDING OF THE
SIGN.
REVISIONS:
+
0
rk d,
m m
6) 07
VOLTAGE:
120 VOLT - VERIFY
SKETCH NUMBER:
JIMMYJ0HNS02
LIED [pmD]m[jo=PAGE:3 of 7
March 4, 2014
CIONES SIGN
-l
4»\\9 TEL: 858-569-1400 FAX: 858-569-1453
9025 BALBOA AVENUE, STE 150
4-;241 -C SAN DIEGO, CA 92123-1520
Kzj
h-irn
NVA|
11 11
U
\ 11 0: 1 : 1 CLIENT NAME:
0
-41 I
"6 1
e
t€1
JIMMY JOHNS
ADDRESS:
3930 SOUTH BRISTOL STREET
SANTAANA, CA 92704
1 6.-e SALES PERSON:
m: m JOHN PANUZZO
DESIGNER:
.-Dri62 1 !M W LMPope
li:'H M
2
0
11 2 .41 - 2
DATE
Ity ll'W ·ry, .
L-
.
- 11 -7: 1
j
FEBRUARY 5, 2014
CLIENT APPROVAL:
JOB #200868 - 93258
PRIMARY ELECTRICAL TO SIGN LOCATIONS
IS TO BE PROVIDED BY OTHERS. 20 AMP
DEDICATED CIRCUIT(S) WITH NO SHARED1/\L m NEUmALS AND A GROUND RETURNING TO
THE PANEL IS REQUIRED FOR All
INSTALLATIONS.
L-J
0
0-0
COLORS REPRESENTED IN THIS DRAWING
ARE FOR PRESENTAnON PURPOSES ONLY
THEY MAY NOT MATCH YOUR FINISHED
PRODUCT PERFECTLY COLOR CALL-OUTS
ARE FOR AMATCHASCLOSEASPOSSIBLE
lEE
r 19 I 26--fc-1
iL O -P
00
C
THIS ORIGINAL DESIGN IS THE SOLE
PROPERTY OF UlmASIGNS. IT CANNOT BE
REPRODUCED, COPIED OR EXHIBITED IN
WHOLE OR PART, WITHOUT FIRST
OBTAINING WRITTEN CONSENT FROM
ULTRASIGNS.
U) g
n
11
11 ro,
S.
*-*THIS SIGN IS INTENDED TO 8E INSTALLED IN
ACCORDANCE WITH THE REQUIREMENTS
OF ARTICLE 600 OF THE NATIONAL
ELECTRICAL CODE AND/OR OTHER
APPLICABLE LOCAL CODES. THIS INCLUDES
PROPER GROUNDING AND BONDING OF THE
SIGN.
G
2 111
i 5 11 1 1 i_r n
- Ei
1:,3'': i
1
a
i
-137.4
4B AK® .
4% '
/052
REVISIONS:
Ch G>
m
m m
m m
fi) 07
\ W
¥19
A
7'in;iilii)lii:TION
March 4, 2014
VOLTAGE:
120 VOLT - VERIFY
SKETCH NUMBER:
JIMMYJ0HNS02
PAGE:2 oF 7
112
..74KEY PLAN
.
, JONESSIGN,
TEL: 858-569-1400 FAX: 858-569-1453
9025 BALBOA AVENUE, STE 150
SAN DIEGO, CA 92123-1520
CLIENT NAME:
MASTER I.D. ,JIMMY JOHNS
G.P. 20
PLANNER 3
ADDRESS:
3930 SOUTH BRISTOL STREET
SANTAANA, CA 92704
SALES PERSON:TRANSFERREC
JOHN PANUZZO
ROUGH DESIGNER:
NAME LMPope
DATE:
FEBRUARY 5, 2014
BELOW:CLIENT APPR0VAL:O INTERIOF
O NO EXTE JOB #200868 - 93258
O ALL MATE
O SCREENI
O SUBMIT
CONDITIONS:
(13 06» W.rt
PRIMARY ELECmICAL TO SIGN LOCATIONS
IS TO BE PROVIDED BY OTHERS. 20 AMP
DEDICATED CIRCUIT(S) WITH NO SHARED
NEUmALS AND A GROUND RETURNING TO
. THE PANEL IS REQUIRED FOR ALL
INSTALLATIONS.
(0 ID *
C 0 32 ¢
1 j:4,2, E- J
f
L
f
1
.
1
-i) 19 , 1
1
J Jj 1
f
r-If
4 3 P 0 14 L d U JL
il,9 t
t
I.
r•
cm=y-
1 I
wift
I ' 4
4 L
2411.
I 6
J 11
f k t· L1
U
tgi
4
11 j
tt \
Fl 4
rpo
COLORS REPRESENTED IN THIS DRAWING
ARE FOR PRESENTATION PURPOSES ONLY
THEY MAY. NOT MATCH YOUR FINISHED
- PRODUCT PERFECTLY ·COLOR CALL-OUTS
AREFORAMATCHASCLOSEASPOSSIBLE.
THIS ORIGINAL DESIGN IS THE SOLE
PROPERTY OF UlmASIGNS. IT CANNOT BE
REPRODUCED, COPIED OR EXHIBITED IN
WHOLE OR PART, WITHOUT FIRST
OBTAINING WRITTEN CONSENT FROM
ULTRASIGNS.·
THIS SIGN IS INTENDED TO BE INSTALLED IN
ACCORDANCE WITH THE REQUIREMENTS
OF ARTICLE 600 OF THE NATIONAL
ELECTRICAL CODE AND/OR OTHER
APPLICABLE LOCAL CODES. THIS INCLUDES
PROPER GROUNDING AND BONDING OF THE
SIGN.
REVISIONS:
m
A m
m *
m ®
(0 037
VOLTAGE:
120 VOLT - VERIFY
SKETCH NUMBER:
JIMMYJ0HNS02
PAGE:1 oF 7
March 4, 2014
f