Loading...
HomeMy WebLinkAbout10179147_2140 E. 17TH - Plan (2)Planning & Building Agency - -5=02*42&2 Building and Safety Division r-GAN- 20 Civic Center Plaza ELECTRICAL SIGN| Santa Ana, CA 92702 REQUIREMENTS(714) 647-5800 www.santa-ana.ora '.-' f 7 : r• -i ' "-• 4.2 i: <N.".72,»1'. '• .i.f. 4 :.ic:.3 ... .N .,4 .1:.* : # 7'4 5 'TA. 'f ":,4·>-1'P:«•ji© ipy€ 12 'tv%-,1,10¢ 74' Code references are to the 2010 California Electrical Code (CEC) All signs require Planning Department approval. All electrical signs require electric plancheck and permit. 1. Manufacturer's instructions are required at the time of submittal C-11: 3-21-2011 2. Submit detailed installation instructions including diagrams to the Building Department for plan review at the time of submittal. Plans must include appropriate items noted by this bulletin. 3. Cash or surety bond in the amount of $200.00 is required at time of issuance for each address. The cash or surety bond will be refunded after all required finals. A building permit is also required - except for open or highlight neon lighting. Installation Requirements: CONTACT FIELD INSPECTOR PRIOR TO SIGN INSTALLATION. (SEE SECTION G OF THIS BULLETIN) 1. Conductors and equipment shall comply with California Electric Code Article 600. 2. All metal parts of a sign shall be bonded in tlie manner specified in Article 250. Isolated metal parts are permitted to be bonded by using an external green insulated conductor. Equipment grounding & bonding conductors must be sized by 110.26 and protected from physical damage. Minimum size is 14 AWG. CEC 600.7 3. A listed disconnect switch in the power supply primary, shall be installed within sight of sign or have permanently installed means for locking in an "OFF" position. This is also true for a transformer enclosure. CEC 600.6 4. A listed receptacle or an approved termination device shall be used for each neon electrode. To relieve stress at terminations, tubing shall be supported with listed tube supports in an approved manner within six inches of electrode connection. CEC 600.41 & 600.42 5. Every electric sign of any type shall be listed by an approved testing laboratory and shall be installed in conformance with this listing. That includes "1 of x", "2 of x" labeling for each separate unit of a multi-unit sign. CEC 600.3 6. All "can" letters and transformers housings shall have section labels that are readily visible after installation. CEC 600.4 7. Transformers shall be located where accessible and be securely fastened in place. Page 1 of 2 P P m P When not inside the sign, they need a 3 foot.high x 3 foot wide x 3 foot deep workspace. Transformers are permitted to be located in attics or canopies provided there is a passageway at least 3 feet high x 2 feet wide with a minimum 12 inch catwalk/walkway from the point of entry. Transformers must be securely fastened and independent of T- bar when above a suspended ceiling. No part of sign mav be fed with flexible cord when located above T-bar ceilinqs. CEC 600.21(E&F) & 400.8 8. Adequate illumination shall be provided for all working spaces about electrical equipment. This applies to attics and canopies when entry is required to service or inspect the equipment. At least one switch is required at entrance. CEC 110.34 & 600.21 9. Doorway to an attic or canopy space shall be minimum 3 feet by 2 feet wide. CEC 600.21(E) E. Open neon outline or highlight lighting. 1. To be treated as a sign by this department. However, Section D-5 & D-6 of this bulletin will not apply. 2. Neon tubing shall be located where not normally exposed to physical damage. Open neon tubing below 9 feet shall be protected from physical damage by an approved shielding method. CEC 600.30 and 1 10.34(E) F. Light-Emitting Diode (LED) Signs 1. Will be treated as a sign by this department. All sign rules in sections A, B, C, D, F, and G will apply as appropriate. 2. LED illumination for signage must be a listed or recognized component. Many LED manufacturers specify particular brands and models of transformers some do not. Manufacturer information to clarify this issue is required on LED sign plans. 3. Unlisted LEDs may not be used in an electrical sign or as permanently installed illumination. 110.3 4. Please have packaging or catalog cut-sheets on hand for inspector to review when LED modules do not bear listing symbols. G. Inspections 1. Contact an Electrical Inspector one (1) workday (minimum) in advance of installation to arrange a site meeting on dav of installation. 2. Call for inspection Monday through Friday, 8:00- 8:30 a.m. at (714) 647-5821. Approved prints and the job card must be on site for inspection. Page 2 of 2 47 SIGN COMPONENTS MANUAL (SAM)November 14,2012 LED 10CV 24 PU LED 10CC 350,120-240 0.175-0.120 2.3-28 0.350 10 VA LED 10CC 350 PU 2. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output. 3. A suitable Fire and Electrical Enclosure shall be provided in the end product. 4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 5. These power supplies are only suitable for use in dry and damp locations. Class 2 Power Supply, Models LED 60CV 12P, LED60CV 24P, LED 100 CV 8, LED 100 CV 12, LED 100 CV 24, LED 100 CV 48. 1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output. 2. The electrical ratings are as follows: Input, 60 Hz. Output DC Model V A V VA LED 100 CV 8 100 - 277 1.3 - 0.5 8 100 LED 100 CV 12 100 - 277 1.3 - 0.5 12 100 LED 100 CV 24 100 - 277 1.3 - 0.5 24 96 LED 100 CV 48 100 - 277 1.3 - 0.5 48 96 LED 60CV 12P 100 - 277 0.8 - 0.3 12 60 LED 60CV 24P 100 - 277 0.8 - 0.3 24 60 3. These power supplies are only suitable for use in dry and damp locations. 4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Company name or trademarks lightech™ Ughtech TIe 4 LED Driver / Hclogen Tran,forrnei, and model designation. 'GE LIGHTING SOLUTIONS LLC6/< BLDG 338E 1975 NOBLE RD EAST CLEVELAND, OH 44112 USA E219167 Border tube kits, Includes Lens Cat. No. GExxBTL; Lens connector Cat. No. GE=BTLC; End cap Cat. No. GE=BTLEC; ED<terior corner kit Cat. No. GExxBTLXC; Interior corner kit Cat. No. GE=BTLIC; Base reflector Cat. No. GEBTBR; Base connector Cat. No. GEBTBC; Cam lock Cat. No. GEBTCL. Canopy Kits, Cat. No. GECPL (8 ft length), GECPEC (end cap), GECPLC, (lens connector), GEBTBCL, GEBTBC. Light guide kits includes: Light guide Cat. No. GEXNLGXX-XXX, Light Guide End Cap Cat. No. GEXXXNLGECZZ, XXX may be any alpha letter representing color. ZZ may be any alpha letter representing size. Light Guide Connector Cat. No. GEXXXNLGYZZ, XXX may be any alpha letter representing color, Y can be any alpha character describing the type of connector. ZZ may be any alpha letter representing size.. Mounting clip Cat. No. GEXNMCXX; Supply wire Cat. No. GEXNSXX, Splice connector Cat. No. GEXNSC1; Weather box Cat. No. GEXWBXX-XXX. 1. Border Tube Kit, Canopy Kit and Light Guide Kit are for Wet Location only use when enclosing LED's connected to a Class 2 circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. 2. The LED border tube kit and Canopy Kit was not evaluated as an electrical enclosure. 3. The LED border tube kit and Canopy Kit was not evaluated as a watertight housing. LED power supplies, Cat. No. GEXLPS21, GEXNPS30-120, GEXNPS31-120 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2.The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3.The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40 C. 4. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 5. The drivers are intended for installation inside an electrical enclosure. 6. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. 7. The drivers are suitable for dry location use only except the drivers Models GEXNPS30-120 and GEXLPS21 are suitable for damp location use. LED array drivers, Models GEXLPS21-U, GEPS 12-60U, GE060/MVA/12T12T1-A. 1. These components have been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. The insulation system of the main isolation transformer designated (T2) in these models is a Class 105(A) insulation system. Unless the modules are mounted as specified in condition of acceptability number 7, a temperature test is required when these models installed within an electrical enclosure or raceway. 5. The maximum measured leakage current of a single unit is 0.49 mA. Leakage current measurements shall be performed when multiple LED drivers are used in the final equipment or when the LED driver is used in combination with other equipment in the end-use product. November 14,2012 SIGN COMPONENTS MANUAL (SAM) 48 6. The unit is intended for installation inside an electrical enclosure. 7. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. 8. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. LED array drivers 60W, Models GEXLPS21 -1004 GEPS 12-60U,GEO060/MV/\/12T12T1 -A 1. These components have been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. The insulation system of the main isolation transformer designated (T2) in these models is a Class 105(A) insulation system. Unless the modules are mounted as specified in condition of acceptability number 7, a temperature test is required when these models installed within an electrical enclosure or raceway. 5. The maximum measured leakage current of a single unit is 0.49 mA. Leakage current measurements shall be performed when multiple LED drivers are used in the final equipment or when the LED driver is used in combination with other equipment in the end-use product. 6. The unit is intended for installation inside an electrical enclosure. 7. The unit may be used within an eledrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. 8. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. LED power supplies, Model GEPS24-100U, GE100/MVA/24T1-A. 1. This component has been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturefs recommended ambient (Tmra) of 40 C. 4. This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an electrical enclosure or raceway. 5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 6. The unit is intended for installation inside an electrical enclosure. 7. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. LED array drivers, Models GEPS 12-20, GEPS 24-20. 1. The maximum measured output voltage, current and power at the output of these models was found in compliance with the limits for Class 2 output requirements. 2. The transformers of these units employ Class 105 insulation system. 3. These components were intended for use in indoor Dry and DAMP location only. 4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in any other direction. 5. These components shall be installed inside an electrical enclosure. 6. Input and Output leads are style 1316, rated 600 V, 105 C, VW-1. Minimum No. 18 AWG. The suitability of input and output connections shall be determined in each end use application. 7. The maximum room ambient temperature permitted by the manufacture is 60 C. The temperature measured on outside enclosure of Models GEPS24-20 and GEPS12-20 are 67.2 C and 77.9 C respectively. The necessity of repeated Temperature Test shall be determined in each end use application if minimum thermal spacings in accordance with Item 4 are not provided. LED Dimmer, Model GEDM1 and GEDM1-A. 1. This component has been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The equipment was submitted and tested for a maximum manufacturers recommended ambient (Tmra) of 40 C. 3. The unit is intended for installation inside an electrical enclosure. 4. This unit is provided with a Class 105(A) insulation system. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. 5. The Xitanium Dimmer is only suitable for use in Class 2 circuits powered by Advance LED drivers with maximum input rating of 24Vdc, 4.lA, or 12VDC, 5A. Dimmer circuit is 0-10VDC. 6. This LED Dimmer Controller must be used with either a 100K Ohms Potentiometer or a standard 0-10 V DC dimmer switch. 7. For dry or damp location. LED Strips, Class 2, Cat. Nos. GE-XX-XX-X-XXX, GE-XX-XX-XX-XXX, GE-)00XX-XXX-XXX, GE-XX-XX-XXXX-XXX, GE-XX- XX-XXXXX-XXX, GE-XX-XX-XXXXXX-XXX, GE-XX-XX-XXXXXXX-XXX, GE-XX-XX-XXXXXXXX-XXX, GE-XX-XX- XXXXXXXXX-XXX, catalog numbers may vary per nomenclature. GE followed by: "XX" representing color: RD, RC, YG, GL, SB, BL, WH, YA, WW, GR, PO, followed by: "XX" representing product line: CL, DS, XL, PT, XN, TM, MX, TU, PG, PX, PH, XH, MH, SS, PM, MM, MH, BS, BD, BI, followed by: "X" to "XXXXXXXXX" representing light strip final assembly or number of LEDs per foot: LA, LE, AA, SX, LX, WXX, TXX, PX, XX, followed by "XXX" denotes any alphanumeric character that represents the color temperature of the LEDs. Cat. Nos. GE-AA-BB-CC-DD, where "AA" may be DS, XN, XNL, XNA, MX, MXL, PG, MM, MMD, SS, PM, PMD, MXH, MXHL, BS, BD, 81 or BIH which represent product line, "BB" may be RD, RC, YG, GL, SB, BL, WH, YA, WW, GR, PO or any alphanumeric character; and "CC" may be any alphanumeric characters or blank. 1. These products are only suitable for connection to a Class 2 power source. 2. When units are connected to a Class 2/ LPS circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2/ LPS supply. 3. These products are suitable for use in dry, damp and wet locations. 4. These products described in this section may be cut into segments per manufacture insulation instructions. 49 SIGN COMPONENTS MANUAL (SAM)November 14,2012 5. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 Conditions of Use as defined in the Sign Components Manual. 6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end use product. NOMENCLATURE: Nomenclature for LED Strip Light: GE-XX-XX-X-XXX, GE-XX-XX-XX-XXX, GE-XX-XX-XXX-XXX, GE-XX-XX-XXXX-XXX, GE-XX- XX-XXXXX-XXX, GE-XX-XX-XXXXXX-XXX, GE-XX-XX-XXXXXXX-XXX, GE-XX-XX-XXXXXXXX-XXX, GE-XX-XX-XXXXXXXXX- XXX. First Set of"XX" = denotes the. color of the LED RD = Red family RC = Red/Orange family YG = yellow family GL = Green family SB, BL = Blue Family WH = White YA = Amber WW = Warm White GR = Green po = Portland Orange Second Set of "XX" = denotes product line CL = channel letter DS =double sided Power Strip XL = tetra long strip PT =power tetra XN =Contour or Contour LS TM =Mini MX =Max TU =Ultra PG =Power GridPX = Power White XL PH =Power White HO XH =Power White XL HO MM =Mini Max SS =Power Strip Third set of 'DO(" denotes Light Strip final assembly as noted below: LA =Light Strip, assembled inside a plastic rod, 8 inch section LE = Light Engine means same as Light strips AA =Light engine, assembled inside a plastic rod, 16 inch section SX or X =Number of LEDs per foot where Xisl =6 LEDs per foot etc. (X can be representative of lt09 digits) \AD<X =Wide Angle light diffuser, where the first X describes the PCB length, A for regular and L for long, and the second X is an alpha numeric character of leds per foot. PX =For PowerGrid (PG), Power Strip (SS) and Double Sided Power Strip (DS) only, where x equals the number of LEDs per foot. Not Assembled in Tube. An optional X may be added to denote wire length between modules where X is S for short, M for Medium, and L for Long. XX =only to be used with DS product line, xx is number that correlates to total length in inches (48 = 48") assembled in acrylic tube. "XXX" denotes any alphanumeric character that denotes the Color Temperature of the LEDs i.e. 65k = 6500,75k = 7500 etc. Splice connector, Cat. No. Ge=SCx; End caps, Cat. No. GexxECx. 1. These products are only suitable for connection to a Class 2 power source. 2. When units are connected to a Class 2/"LPS" circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2/"LPS" supply. 3. These products are suitable for use in dry, damp and wet locations. 4. These products described in this section may be cut into segments per manufacture insulation instructions. 5. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions of Use" as defined in the Sign Components Manual. 6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end use product. LED Controller, LED Tetra FX Special Lighting Effects Controller, Cat. No. GEFX1 1. This product is suitable for only when connected to a Class 2 power source or LSP, Model GEXLPS20, GEXLPS21, GEXNOS30 or GEXNPS31 by GE. Rated Input is 12/24 V dc, Output is 12/24 V dc. 2. This product is a Class 2 device suitable for use in dry, damp and wet locations. 3. The controller shall be provided in a suitable housing when use in wet locations. 4. Lead wires are R/C (AVL\/2), Style 2651, rated 105 C, 300V. Not suitable for use inside walls, above ceiling or other similar concealed spaces unless mounted inside an electrical enclosure. 5. The controller is provided with a DMX 5-pins input connector. The pin arrangements in the connector shall always be the same. The DMX controller is capable of providing the 4 channel dimming, flashing, chasing, sequencing, color mixing, and color changing functions. LED wire, Cat. No. GExxSWx. Nomenclature for Splice Connectors, LED Wires, End Caps: xx denotes product line, CL = channel letter, DS = double sided, XL = tetra long strip, PT = power tetra, XN = Exposed Neon, TM = Mini, MX = Max, TU = Ultra, PG = November 14, 2012 SIGN COMPONENTS MANUAL (SAM) 50 Power Grid, PX = Power White XL, PH = Power White HO, XH = Power White XL HO, MM = Mini Max; 'x' denotes design revision number. 1. These products are only suitable for connection to a Class 2 power source. 2. When units are connected to a Class 2/"LPS" circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2/"LPS" supply. 3. These products are suitable for use in dry, damp and wet locations. 4. These products described in this section may be cut into segments per manufacture insulation instructions. 5. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions of Use" as defined in the Sign Components Manual. 6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end use product. LED power supplies, Models GECLPS4. 1. LED power supply, Catalog No. GECLPS4 for dry and damp locations. 2. Each power supply output is Class 2. LED power supplies, Models GECLPS4D. 1. LED power supply, Catalog No. GECLPS4D for dry and damp locations. 2. Each power supply output is Class 2. LED power supplies, Models GECLPS6 and GECLPSPHA. 1. LED power supply, Catalog No. GECLPS6 for dry and damp locations. ' 2. Each power supply output is Class 2. LED power supplies, Models GECLPS3. 1. LED power supply, Cat. No. GECLPS3 for dry and damp locations. 2. Each power supply output is Class 2. LED power supplies, Models GECLPS5, GECLPSPH, GECLPSPW, GECLPSWH. 1. LED power supply, Cat. No. GECLPS5, GECLPSPH, GECLPSPW and GECLPSWH for dry and damp locations. 2. Each power supply output is Class 2. Power supplies with Class 2 outputs, Models GEPS24-80, GEPS12-60, GEPS24-20. 1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp locations. 2. These power supplies need to be installed in an enclosure with a means for the connection to conduit. 3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than 13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110°C. Similarly, for Model GEPS24-20, a temperature test is required when installed in an enclosure smaller than 13.5 by 6 by 4 inches, but the maximum temperature on the output transformer by thermocouple is 90°C. 4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet locations. Power supplies with Class 2 outputs, Model GEXNPS30. 1. This component has outputs that qualify as being Class 2. 2. These components are intended for use in dry location only. 3. The transformer employs a Class B (130) Insulation System. 4. These components shall be installed in compliance with the enclosure and mounting requirements of the ultimate application. 5. The maximum room ambient temperature permitted by the manufacture is 50(C. 6. A Temperature Test is required of the power supply installed in an enclosure that measures less than 13.5 by 6 by 4 inches. The maximum temperature on the output transformer by thermocouple is 110( C. Power supplies with Class 2 outputs, Models GEPS24-180U, GE180/MVA/24T1-C 1. The maximum measured output voltage, current and power at the output of these models was found in compliance with the limits for LPS output requirements and additionally evaluated to comply with Class 2 output criteria. 2. The transformer employ Class B insulation system. 3. Power Supply is intended for use in indoor Dry and Damp location only. 4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in any other direction. 5. Input and Output leads are style 1316, rated 600 V, 105°C, VW-1. Minimum No. 18 AWG. The suitability of input and output connections shall be determined in each end use application. 6. The power supply was submitted and tested for a maximum manufacturer's recommended Tc point described in the table below. If adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature test shall be conducted in the end use product. Model Input Voltage, HZ Max. Case Temp @ Tc, °C Ambient, °C GE180/MWV24T1-C, GEPS24-100-277, 60 80 60 180U LED Light Engine, Cat. Nos. 1110-WH-ZZ-TTK, 1110-RD-ZZ-TTK, catalog numbers where: "ZZ" representing assembly version: followed by: "TT" - Optional - represents the color temperature of the LEDs in degree "K" Kelvin. Cat. Nos. 1111-XX-ZZ-Y-UK, catalog numbers may vary per nomendature.: "XX" representing color: RD, RC, YG, GL, SB, BL, WH, YA, WW, GR, PO: "ZZ" representing assembly version; "Y" representing number of LEDs; followed by: "TT" - Optional - represents the color temperature of the LEDs in degree "K" Kelvin. 1. These products are only suitable for connection to a Class 2 power source. 2. When units are connected to a Class 2/"LPS" circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2f'LPS" supply. 3. These products are suitable for use in dry, damp and wet locations. 4. The suitability of the LED Light Engine mounting means shall be determined in the end-use application. 5. The suitability of the LED Light Engine to be used without an additional electrical enclosure shall be determined in the end-use application. 6. These products described in this section may be cut into segments per manufacture insulation instructions. 7. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions of Use" as defined in the Sign Components Manual. 51 SIGN COMPONENTS MANUAL (SAM)November 14,2012 LED Driver with Class 2 Output, Models GEPS12D-60U, GEPS24D-80U. 1. These LED Drivers have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output. 2. These products are provided with the following electrical ratings: Model No.Input Voltage (V Input Freq Input Current Output Voltage Output Current Output ac) (HZ) (A) (V dc) (A) Power (W) GEPS24D-80U 100-277 50/60 1.1 24 3.3 80 GEPS12D-60U 100-277 |50/60 0.85 12 5.0 60 3. The load powered by the Class 2 output of the LED drivers are suitable for use in dry, damp and wet locations. 4. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 5. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less than 4 inches (102mm) apart when arranged otherwise. 6. These products shall be enclosed in the end product. 7. The unit is intended for being used in permanently wired signs. 8. The suitability of output leads, rated No. 24 AWG minimum, rated 80°C minimum, 600 V, shall be determined in end product use. 9. These units may provided with Dimming Input (Purple and Gray wires) to control output current range, the suitability shall be determined in each end-use application. 10. These products are intended for use in dry and damp locations LED Driver with Class 2 Output, Model 1110PS-60S. 1. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted on page 1. 2. These LED drivers are provided with Class 2 output. 3. These LED drivers are intended to be operated in a maximum ambient (Ta) noted as below: Model Ta (°C) LD-60-UV-1214V 40 4. These LED drivers are intended for use in dry and damp locations except that models LD-60-UV-1214V and LD-60-UV-1214\A SC are suitable for dry location only. 5. These LED drivers are provided with 18 AWG AWM input and output leads. The suitability of the wiring and the need for a suitable enclosure shall be considered in the end product. 6. These LED drivers are intended to be operated on a maximum 20 A branch circuit. 7. The need of the grounding means shall be determined in the end product. 8. These LED drivers shall be enclosed within a suitable end product enclosure. 9. For model LD-60-UV-24V-DIW, the conduit knockout test was not conducted. The suitability is to be determined in end product. 10. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 11. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less than 4 inches (102mm) apart when arranged otherwise. LED Driver with Class 2 Output, Model GEPS12-180U. 1. The output (Red/Black) of each unit complies with Class 2 criteria of UL 1310. 2. The device is provided with 18 AWG input and output leads. The suitability of input and output connections shall be determined in end-use application. 3. The suitability of grounding means shall be determined by end product. 4. The device is not intended for field wiring used. 5. The device is intended to be connected to a maximum 20 A branch circuit. 6. The devices are of the constant current type that requires the proper number of LED modules and controllers that does not exceed the maximum output voltage/current. 7. The measured maximum external enclosure temperature (Tc) is 77.2 degree C when the room ambient temperature are 60 degree C. The suitability shall be determined in end application. 8. The devices employ input surge suppression protection, Cat. No. S14K385E2K1 under UL File E321126, which is intended end- use SPD type 2. The suppressed voltage rating is 385 Vac. The suitability of use of this component shall be determined in the end-product application. 9. No mechanical test has been conducted for the models and the metal chassis is considered as dead metal. The devices shall be mounted in the intended manner in an enclosure, having adequate strength and thickness with acceptable spacing being provided. 10. The device has been evaluated for dry and damp locations use only. 11. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 12. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less than 4 inches (102mm) apart when arranged otherwise. LED Driver with Class 2 Output, Model No. GEPSJB60. 1. The j-Box Enclosure has been evaluated only for use and connection to LED Class 2 Drivers GEPS 12-60, GEPS12O-604 GEPS24-80, and GEPS24O-80U. 2. These products complete the electrical enclosure when installed over the primary wiring of the LED driver. 3. The suitability of the mounting shall be determined in end use application. 4. The enclosure has been evaluated only for use in Dry and damp locations only 5. Supply connection shall be determined in the end used application. 6. Ground Screw size is No. 6 thread forming screw with cupped washer is provided for grounding. The maximum size ground wire that can be used is 14AWG. The maximum size branch circuit that the units can be connected to is 15A unless a 16- 14AWG six inch pigtail lead supplied by sign company is connected to ground terminal and then spliced to 12AWG ground wire of a 20 A branch circuit. 7. Cover Screw shall not be of a thread forming or self-tapping type. 8. To keep the enclosure from rotating, the Enclosure shall be secured by at least one mechanical fastener. November 14, 2012 SIGN COMPONENTS MANUAL (SAM) 52 9. The J-box has been evaluated for an ambient of 40°C. 10. The J-box label shall be marked for a 75°C supply wire connection. GEMINI INC E16382 103 MENSING WAY CANNON FALLS, MN 55009 Plastic Channel Letters, Cat. No. Plastic Channel Letters. 1. The channel letters may be used as an electrical enclosure when provided with sign face material in the end-use application that is suitable for electrical enclosure use. 2. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. 3. Openings for drain holes, conduit, electrode receptades and mounting shall be provided in accordance with the Standard. 4. The channel letter plastic is rated 80°C. 5. For outdoor or indoor use. 6. Spacings from the channel letter to the enclosure for neon transformers or power supplies shall be in accordance with Standard UL 48. Plastic Channel Letters, Plastic Indoor Channel Letters. 1.The channel letters have been evaluated for indoor application only. 2.The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. Openings for conduit, electrode receptacles and mounting shall be provided in accordance with the Standard. 3.The channel letter plastic is rated 50°C. 4. The channel letter may be used as an electrical enclosure when provided with a sign face material in the end-use application that is suitable for electrical enclosure. 5. Spacings from the channel letter to the enclosure of neon transformers or power supplies shall be in accordance with Standard UL 48. Plastic Channel Letters and Face, Plastic Indoor Channel Letter Sign Body and Face 1. The channel letters have been evaluated for indoor application only. 2. The channel letters are not suitable as an electrical enclosure. 3. The channel letters are suitable for Class 2 LED and neon applications. 4. The channel letter plastic is rated 50°C. 5. Openings for conduit, electrode receptacles and mounting shall be provided in accordance with the Standard. 6. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. 7. Spacings from the channel letter to the enclosure of neon transformers or power supplies shall be in accordance with Standard UL 48. Aluminum reinforced thermoplastic sign face trim, Type Gem Brand. 1. These trim materials are used to secure a rigid thermoplastic sign face to an outdoor or indoor sign. 2. The ability of the trim to exclude water from contacting live parts needs to be evaluated in the end product. 3. Minimum No. 8 sheet metal screws need to be provided for securing the trim to the sign body. The maximum spacing between screws shall not exceed 18 in. and no fewer than four screws are to be used per face. 4. These products do not comply with enclosure requirements. 5. The following are among the items to be considered in the end-use application. 1. Acceptable for use in wet locations. 2. Water exclusion must be determined in the end product. 3. Minimum 5 cm (2 in.) spacing from heat producing components required. 4. The specified solvents are continuously applied to edge of acrylic or polycarbonate sign face. Additional specified adhesives may be applied for the final bond. Sign Face Generic Material Solvent Final Bond Adhesive Sign Trim Generic Material Methyl Methacrylate Weld-On #4 or Weld-On #16, Weld-On Cellulose Acetate Butyrate (Acrylic) (Methylene Chloride )#58 (Polycarbonate)Weld-On #4 or Weld-On #58, Lord Cellulose Acetate Butyrate Methylene Chloride Adhesive #7550 Plastic Channel Faces, Type Gemini Gemlite Channel faces and Gemini Edge Glo faces 1. The sign faces have been evaluated for indoor & outdoor applications. 2. The sign faces are not suitable as an electrical enclosure. 3. The sign face plastic is rated 50°C. 4. The sign face for channel letter is not to be considered as providing a weatherproof enclosure, therefore all internal components shall be suitable for outdoor use or shall be completely enclosed and protected from weathering. 5. The neon tube or LED shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. 6. The sign face may be used with either plastic or metal channel letters. Plastic Channel Letters, Type Indoor, outdoor designated "GEMINI FORMED SIGN BODY" for Class 2 powered LED modules strips. 1. These products are only suitable to house LED modules strips that are powered by UL Listed or R/C Class 2 Power Supply rated max 30 VDC or max 15 VAC. 2. These products are not suitable for use as electrical enclosures. 3. These products shall be provided with mounting instructions. 4. For outdoor applications, if these products are used to house components other than Class 2, then all internal components shall be suitable for outdoor use or shall be suitably enclosed. Plastic Channel Letters, Type Gemini Channel Letters 1. The Gemini Channel Letters have been evaluated for indoor & outdoor applications. 2. The Gemini Channel Letters are not suitable as an electrical enclosure. 3. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. PLANNiNG DIVISION MASTER I.D.do (3 l. / eMZK G.P.Zone Of1> DATEPLANNER TRANSFERRED BY DATE r 7 , PLANNING INSPECTION REQUIRED: ROUGH FINAL Y NONE 21.,03. CHAXPL ,NAME II Il (714) 4429 - pz deBanfi23 2 Z FUTURE REVIS!ONS. S CHECKED AND CONDITIONS FNLY _ .-- _ -... ' A:L.TERATiONS,/MODIFICATIONS r J 9 64(2 TAIALS TO MATCH EXISTING1 ,22\C| Cgf.:.-fiN|3 REQUIREDi >3142 X 05 P- -1 't --IND!1-?ONS:Sle*/ 0-b(1«73 0097 2140 East 17th Street Santa Ana, CA. 92705 YOUR PARTNER IN BUILDING AN OUTSTANDING IMAGE image national sign .0, ...bringing your imoge to light! -1 APPROVED nt' .r 0 r ..a 17Ai -j J{4 Cl Tral 0 T.' 0G f -r 0 0 *r 4 F-f· f *9L,.-Ai=u,31 : UEi,-1- 4 . 1, r J- 1 bE **id. u:.t and purp04*fij,ls cW67;dr26,6,0 *,6.14. a til€'&*-7*-- 0462*-TREh endaia. fic-ar. *81 rn- -,ci priritaxlkn wil-vaiy 66rn ami@ Atii,la Giaki- ' Existlng painted surfaces wil have a percept,bta a ffemnce in shade and sheen from your sIgn finish. Provkling 8 sample of U,8 pairrt you wish to match ora Matthews palnt color formula will mir,Imize the diffarences.16265 Star Road Nampa. ID 83687 toll free: 800.592.8058 tele: 208.345.4020 fax: 208.336.9886 www.imagenational.com .J'. 1 I 333141:imill:11:Imimilillill........*I .Imm %10 Ill·=1,.9}1*FA-2 2140 05.17.2013 4 0 6-irillilliriltiflioullat it mulmt .1181"/P/,B= .Ji-%-"..9 1.i-E. 17th Street ---BAN-0097-C95 Santa Ana, CA. 92705 =moU -- 45 4,?41*,9*'7rugi¥·XS;;AA,e:*.7.--;. R. Paulson . 4:JW 1, . C.• \: 4:"-ri¥-IP-7'15811:1:WZliV 6 2013 knuni t-Mens. Ihi; de,on biA n,1-1 1 el owlhe,Ilip h Im- N,t-l In (im,0,) hkh nam Iha 0,ili,I, ING»,lim k, 11 ,opyinht In of 110 Unll•190!,s (t t 11. Ui fodl4 41= -4 * Il Il• u of Ihis dN,n i, *i.td ), imle, in illi, illo,e ors; ill• 1,[1 kll +1$ 10· e) ilpled,o #d; drig *it. ill plo,Ilk kIn Nu •i,R; 4 .4 1Ir.• i,M to[ 46n th•,14 * 4 the dei,N 4 0 4 1-I• d al•¢hip; -I 4 460|•t 14• d,9,4 4.,· 5 Banfield store # J{ M PET HOSPITAL 0097 16 |26 C/ko-f "17-12 EQ. 6'-0" 61 8'-43M"1 EQ. 4 =11II[lit• 1--THE PET ¥OSPITAL A-RF®©*PDVAG ' 28" x 600"=14sf i SAME I AS EXISTING -/ 160'-6 " +/- EXISTING BUILDING STOREFRONT - w/ NEW BANFIELD LED CHANNEL LETTERS 4 PATCH & PAINT AS REQUIRED ST[Noon"IMP PRE-PANIED V,NTE AL[IM. 1 ON FACE OF AP.(P Only "0 0»26 + PeppeR/her 3 Te,-1* Pit/'· Elanfie#F PEI ®©5[Pn 11 New 211" "Banlield" Channel Letter Lavout scale: 1/2"=1'-0"19.5st EXISTING BUILDING STOREFRONT - REMOVE & DISCARD EXISTING BANFIELD POInt121 Ihave a perceptible-diftencelnshaaeand :haintron,yoursign fklish, Pr·ovidlng alarn02; BTIIBI 6ediMerZ;16265 Star Road Nampa, ID 83687 toll free: 800.592.8058 tele: 208.345.4020 fax: 208.336.9886 www.imagenational.com hin 0-'PET HOSPITAL 0097 salihAA. 92705 =1=m< RPaulson . .mt 117 1....i..........4-"."M..........,PIe #itrEON,s,237 Banfield store # 2140 05.17.2013 S. Carico IM Nt BAN-0097-C ---: ..-.-' @1141 6 2013 [moqi „-1·* This le.lon gonnli,irol *0.4 6/h,1%4 4 Im,F lition,1. In[. (in,m) *4-, lo,ilish; Foicn b,· W top,tioh,11,; of th, UnkW Sm!,s (* W. U $. rodo). Al ii,1,59,1 f-d 4 imal, -l •lil thR uw 011!1-6 dN,n h wili,3,4 1, @m, m .ring, iNMeor,nihi eltill,iR i,histo: n),Gp,d,;o,Ihis de* m mpiat, in Ilm,hk h,m e i., iign: ,) pmpum dDIA,1 -,)3 bo,mil upon Ih• d#40; 1 lils,nb,e {*05 41,bed•Ii,n br,ob M 00= imt,61Id ·7*no,ship: n,W I) di,40,1h• d,1, FAM, y 8' 43/4. 51/2" 2'-4 "5' 71/1 STEP-DOWN JUMP - PRE-PAINTED WHITE AWM. ON FACE OF JUMP ONLY A. .WL £1 BanfiIct PEL[f HI ©EP®31 Ll r - New 28 1,11 Banfield" Channel Letter Lavout.1.2% - scale: 1"=1'-0'19.5sf -0 ISTA O FACE:O RETURNS:J MATERIAL/LOGO: 1/8" FORMED ACRYLIC MATERIAL: PRE-PAINTED .040 ALUM. COLOR: 020-4 or 2447 WHITE SIZE: 5" 1\ L L VINYL: #84 Tanaerine COLOR: PRE-PAINTED DK. BRONZE (WHITE INSIDE) ILLUMINATION: MATERIAL: GE LED SIZE: TBD COLOR: WHITE Non-Corrosive Securement 1/4" Rivet Nut w/ All-Thread Attachment Cor.4*17-13" Screws ./Uil;, 3.9 Pe.r le#er) MATERIAL/LETTERS: 3/16" ACRYLIC COLOR: 020-4 or 2447 WHITE VINYL: ARLON #236 Turguoise B. 1/2" Liquid Tight Conduit to 120v Power C. C.65> 3:r L€P WA ·Tkrouf k u/64 f D. (1) 20 amp 120v Circuit Required (supplied by others than Image National) E. 1/4" Weep Holes as Required NOTE: Disconnect Switch Required in Transformer Box (Supplied by Image National) O TRIM CAP: MATERIAL: 1" JEWELITE TRIM CAP COLOR: BLACK O STEP DOWN: MATERIAL: PRE-PAINTED .040 ALUM. SIZE: 33/4" COLOR: PRE-PAINTED WHITE (WHITE INSIDE) 6 BACKS: MATERIAL: PRE-PAINTED .063 ALUM. COLOR: PRE-PAINTED WHITE (WHITE INSIDE) G ELECTRICAL: SEE LED LAYOUT SHEET lit is the inter' and pt'pos' of this color rande,Ing to p,6vlde a basic color representolbn ot yoOr sign lin[sh and color. Howavar. digital media *Aii@ir,tod 0663 wil val*-il= 66kil peint nnEh and c@or. J - ,; -1 Eistil g painted surfaces wil have 8 parceptible dinerence In shode and shain from your sign finlsh. Provldlng a samplo of tha pallt you wlsh to match ora Matthew: paint color ionnuta HAU minlmiza the dilforences.16265 Star Road Nampa, ID 83687 tott free: 800.592.8058 tele: 208.345.4020 fax: 208.336.9886 www.imagenational.com 81[0112 18. al·m. Pr ..1,1.1,11,1,1111/.111/F'/2.95934 2140 05.17.2013 S. Carico image national signs i,· 8,-,fir ...bringing your image to light!E. 17th Street ----- BAN-0097-C -).op.-im--=r-#.'017, Ul]Santa Ana, CA. 92705 =•{a 2.lot R. Paulson - 4; 31tlke• tar•1:M As diF h.• Aftf•Ii n*ld Ithii. 4 Imi,0 ·1,ir.l li [i,·i,),+i,Cur.)1* %#141 Ir.m·i l, I·e f cp: f-#1 4,: Bri}•1!114 5%1:st•t.') U $. faq. P 4144,W'la Y,Xquu, Ma l| th, dIT, *84. :,di rl| hi k·•48 I .rklim, imn,c iwf, 11, 1,16, 1,142 4 1,1 ·Mic•6$ 1/4,1, 16*7 I MV 4,·s (1 Ii,•ii. 40'-4 dr,;.,;.•,a.,4 1 01 42,2, d.*n· 4 d,9,•.r·• !* •C"be *•39, 1:4 ·40 r• uk, Im,de U.l,r·4 - 4 #1211'* ALM:944, Banfield store # PET HOSPITAL 0097 1-9-15 l01'79)L) 9 e monument sign(s)dedicated circuit breaker(s) mus / 520 j -S:*2,6 07 n City of Santa Ana. CBC & CEC 2010 P,\0091.tftf Minimum (4) screws per letter, maximum 24" on center, 2"lockabi,..' teoput,Vidue or penetration, #10 sheet metal screws, &attic or above (2) 44" drain holes per lettertt soo.s o\Ner SUPPW orn assage *1\m _©efis try as soo-2.A fceiling 6.1 mmediately · a ladderwith a 2 x 3 foot access door &p\00 ma*Nal ·Citv of Santa Ana Planning & Building Age . -·..-7-'·., G:7,31=2r· ELECTRICAL -3 -l i PLAN APPROVAL 1 , This set of plans and specifications must be kept on the job at all times and it is unlawful to make any changes or alteratlons on same without written per- mission from the Departrnent of Building .Safety City of Santa Ana. rhe approval of this plan and specifications SHALL NOT be held to permit nor be an approval of the violation or any provisions of ANY City Ordinance or State Law.ApprPirfqj:*43* rl),4123 CITY OF SANTA ANA DEPARTMENT OF BUILDING SAFETY - PERMIT TYPE: MEdH GRAD!NG PERMIT#10019)43952267 OCC. GROUP CONSTR.TYPF CODE EDITiON 5200 . FLOOD ZONF. FLOOD ZONE CERTIF. REQ'D YES 49 MICROFILM YES NO j RADIANT BARRIER @ ROOF YES Ng/' RESIDENTIAL DEV. FEE YES 40 SCHOOL DISTRICT YES NO .. 0