Loading...
HomeMy WebLinkAbout10179804_1229 E. 17TH - Plan (2)Planning & Building Agency Building and Safety Division 20 Civic Center Plaza P.O. Box 1988 (M-19) Santa Ana, CA 92702 (714) 647-5800 www. santa-ana.orq ELECTRICAL SIGN REQUIREMENTS SE?£,#27<9·W,WhW#*Itti·*'2¢I/,&Jlp'Zikt w.:N27.e·VU,BA,yeae/·ip:>0egeabPSNEZ'M?kK?92EEFWEt.%,3,7%%133+Imil Code references are to the 2010 California Electrical Code (CEC)C-11: 3-21-2011 A. All signs require Planning Department approval. B. All electrical signs require electric plancheck and permit. 1. Manufacturer's instructions are required at the time of submittal. 2. Submit detailed installation instructions including diagrams to the Building Department for plan review at the time of submittal. Plans must include appropriate items noted by this bulletin. 3. Cash or surety bond in the amount of $200.00 is required at time of issuance for each address. The cash or surety bond will be refunded after all required finals. C. A building permit is also required - except for open or highlight neon lighting. D. Installation Requirements: CONTACT FIELD INSPECTOR PRIOR TO SIGN INSTALLATION. (SEE SECTION G OF THIS BULLETIN) 1. Conductors and equipment shall comply with California Electric Code Article 600. 2. All metal parts of a sign shall be bonded in tlie manner specified in Article 250. Isolated metal parts are permitted to be bonded by using an external green insulated conductor. Equipment grounding & bonding conductors must be sized by 110.26 and protected from physical damage. Minimum size is 14 AWG. CEC 600.7 3. A listed disconnect switch in the power supply primary, shall be installed within sight of sign or have permanently installed means for locking in an "OFF" position. This is also true for a transformer enclosure. CEC 600.6 4. A listed receptacle or an approved termination device shall be used for each neon electrode. To relieve stress at terminations, tubing shall be supported with listed tube supports in an approved manner within six inches of electrode connection. CEC 600.41 & 600.42 5. Every electric sign of any type shall be listed by an approved testing laboratory and shall be installed in conformance with this listing. That includes"1 of x", "2 of x" labeling for each separate unit of a multi-unit sign. CEC 600.3 6. All "can" letters and transformers housings shall have section labels that are readily visible after installation. CEC 600.4 7. Transformers shall be located where accessible and be securely fastened in place. Page 1 of 2 When not inside the sign, they need a 3 foot high x 3 foot wide x 3 foot deep workspace. Transformers are permitted to be located in attics or canopies provided there is a passageway at least 3 feet high x 2 feet wide with a minimum 12 inch catwalldwalkway from the point of entry. Transformers must be securely fastened and independent of T- bar when above a suspended ceiling. No part of sign mav be fed with flexible cord when located above T-bar ceilinqs. CEC 600.21(E&F) & 400.8 8. Adequate illumination shall be provided for all working spaces about electrical equipment. This applies to attics and canopies when entry is required to service or inspect the equipment. At least one switch is required at entrance. CEC 110.34 & 600.21 9. Doorway to an attic or canopy space shall be minimum 3 feet by 2 feet wide. CEC 600.21(E) E. Open neon outline or highlight lighting. 1. To be treated as a sign by this department. However, Section D-5 & D-6 of this bulletin will not apply. 2. Neon tubing shall be located where not normally exposed to physical damage. Open neon tubing below 9 feet shall be protected from physical damage by an approved shielding method. CEC 600.30 and 1 10.34(E) F. Light-Emitting Diode (LED) Signs 1. Will be treated as a sign by this department. All sign rules in sections A, B, C, D, F, and G will apply as appropriate. 2. LED illumination for signage must be a listed or recognized component. Many LED manufacturers specify particular brands and models of transformers some do not. Manufacturer information to clarify this issue is required on LED sign plans. 3. Unlisted LEDs may not be used in an electrical sign or as permanently installed illumination. 110.3 4. Please have packaging or catalog cut-sheets on hand for inspector to review when LED modules do not bear listing symbols. G. Inspections 1. Contact an Electrical Inspector one (1) workday (minimum) in advance of installation to arrange a site meeting on dav of installation. 2. Call for inspection Monday through Friday, 8:00- 8:30 a.m. at (714) 647-5821. Approved prints and the job card must be on site for inspection. Page 2 of 2 . June 19,2013 SIGN COMPONENTS MANUAL (SAM) 2 Transformers and power supplies covered under this category are marked with a Type number from 1 to 8 in association with the location designation "Indoors," "Outdoors," 'Weatherproof' or "WP." These Type numbers identify particular construction features associated with a particular transformer or power supply as identified below: • Type 1 - Open core-and-coil neon transformer or unenclosed neon power supply with body of the unit and input and output terminals or leads that should be enclosed in accordance with end-product requirements. • Type 2 - Neon supply with input and output terminals or leads that should be enclosed in accordance with end-product requirements. • Type 3 - Neon supply with input terminals or leads enclosed and intended for connection to a permanent wiring system, and with output terminals or leads that should be enclosed in accordance with end-product requirements. • Type 4 - Neon supply with input and output terminals or leads enclosed and intended for connection to a permanent wiring system. • Type 5 - Neon supply with input terminals or leads enclosed and intended for connection to a permanent wiring system and provided with integral receptacles for output connection. • Type 6 - Cord-connected neon supply provided with integral receptades for output connection. • Type 7 - Cord-connected neon supply with output terminals or leads that should be enclosed in accordance with end-product requirements. • Type 8 - Cord-connected neon supply with enclosed output terminals or leads. ALLANSON INTERNATIONAL INC 33 CRANFIELD RD E39591 TORONTO, ONTARIO CANADA M4B 3H2 Neon Power Supply, Indoor Type 7, Cat. No. SS9358-18 Transformers, Outdoor Type 5 Applicable Conditions of Use - C. D. E. Cat. Nos. 960EK120,960E1<277,960EK347, P960EK120, P960EK277, P960EK347,960EKF120,960EKF277,960EKF347, P960EKF120, P960EKF277, P960EKF347,7560EK277,7560EK347, P7560EK120, P7560EK277, P7560EK347,7560EKF277, P7560EKF120, P7560EKF277, P7560EKF347,660EK120,660EK277,660El<347, P660EK120, P660El<277, P660EK347, 660EKF120,660EKF277,660EKF347, P660EKF120, P660EKF277, P660EKF347,560EK120,560EK347, P560EK120, P560EK277, P560EK347,560EKF120,560EKF347, P560EKF 120, P560EKF277, P560EKF347,460EK120,460EK277, 460EK347, P460EK120, P460EK277, P460EK347,460EKF120,460EKF277,460EKF347, P460EKF 120, P460EKF277, P460EKF347, 360EK120, 360EK277, 360EK347, P360EK120, P360EK277, P360EK347, 360EKF120, 360EKF277, 360EKF347, P360EKF120, P360EKF277, P360EKF347. Transformers, Outdoor Type 5 Applicable Conditions of Use - C, D, E. Cat. Nos. Mini 330EK, Mini 430EK, Mini 530EK. Power Supplies, Indoor Type 7 Applicable Conditions of Use - A, C, G. Cat. No. SS935B-18,Cat. No. 630FNI. Transformers, Outdoor Type 2 Applicable Conditions of Use - A, B. Cat. Nos. 330CI120, P330CI120,330CI277, P330CI277,330CI347, P330CI347,430CI120, P430CI120,430CI277, P430CI277, 430CI347, P430CI347,530CI 120, P530CI 120,530CI277, P530CI277,530CI347, P530CI347,630CI 120, P630CI 120,63061277, P630CI277,630CI347, P630CI347. Transformers, Outdoor Type 4 Applicable Conditions of Use - A. B. Cat. I\los. 330FI 120, P330FI 120, 330FI277, P330FI277, 330FI347, P330FI347,430FI 120, P430FI 120, 430FI277, P430FI277, 430FI347, P430FI347,530FI120, P530FI120,530FI277, P530FI277,530FI347, P530FI347,630FI120, P630FI120,630FI277, P630F1277,630F1347, P630FI347. 1. The secondary circuits of these transformers are not to be interconnected in series or parallel. 2. The secondary circuits of these transformers are not to be connected to ground. fMay or may not be provided with a suffix "T". EVERBRITE LLC E122656 4949 S 110m PO BOX 20020 GREENFIELD, WI 53220 Transformers, Outdoor Type 7. Applicable Conditions of Use -A, C. G- Series 2612, Model 800-0128; Indoor Type 2, Series "NuAUX", Models 800-0174, 800- 0175, 800-0176, 800-0177, Series 3612, Models 800-0232,800-0233 1. The "Animotion" system consists of the following components: Series 2612, Model 800-0128 or Series 3612, Models 800-0232 or 800-0233, Series "NuAUX," Models 800-0174,800-0175, 800-0176, and 800-0177, and Animotion Controller Model 800- 0066,800-0067, or 800-0068. 2. Series "NuAUX," Models 800-0174, 800-0175, 800-0176, and 800-0177 are only for use with Series 2612, Model 800-0128 or Series 3612, Models 800-0232 and 800-0233. 3. Each Class 2 output on Series 2612 Model 800-0128 and Series 3612, Models 800-0232 and 800-0233 shall not exceed 2.4 A. 4. A maximum of two =NuAux" transformers may be connected directly to each Model 800-0128, Model 800-0232 or Model 800- 0233 Class 2 output. FRANCE A SCOTT FETZER CO E10092 June 19, 2013 SIGN COMPONENTS MANUAL (SAM) 40 3924 VARSITY DR ANN ARBOR, MI 48108 Class 2 Powered LED Illuminated Sign, designated as "LED Beer Sign". 1. These products are only suitable for connection to a Class 2 power source rated 30 Volt DC or less. 2. These Class powered products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are suitable for use in dry locations with supply sources rated at 30 Volts DC or less. EUROCOM-INC E342497 SUITE 202 8411 STERLING ST IRVING, TX 75063 LED Modules, Model Nos. SL-CL-420, SL-IP-CL-420, SL-HI-500, SL-HI-500RGB, SL-IP-HI-500, SL-IP-HI-500RGB, FK-IP-02, FK- IP-03, FK-IP-04. All models may be followed by additional suffixes for color temperature. 1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy limited circuit and is rated greater than 12 V DC. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. EVERBRITE ELECTRONICS INC 720 W CHERRY ST E325903 CHANUTE, KS 66720 LED Modules, Class 2 LED Modules designated as "Current Limited LED Assembly" series, XXX-YYYY, where XXX may be any combination of numeric characters from 000 to 999; Y'(YY may be any combinations of alphanumeric characters from 0000 to 9999 or AAAA to ZZZZ; or suffix XXX-YYYYY , where XXX and YYUY can be any alphanumeric characters. 1. LED modules designated as "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY are only suitable for connection to a Class 2 power source rated max 60 Volt DC or less when used indoors. 2. LED modules designated "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY are only suitable for connection to a Class 2 power source rated max 30 Volt DC or less when used outdoors. 3. LED modules designated as :'Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated greater than 60 V DC for indoor use. 4. LED modules designated as "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated greater than 30 V DC for outdoor use. 5. LED modules designated as "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY are each rated max. 90 watts per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 6. LED modules designated as "Current Limited LED Assembly" series, XXX-YYY'Y or XXX-YYYYY are suitable for use only in dry locations with supply sources rated at max. 60 Volts DC or less. 7. LED modules designated as "Current Limited LED Assembly" series, XXX-YYYY or XXX-YYYYY are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less 8. These products may be secured in place in the end product by any means available. 9. When these products are used in applications other than signs or Outline lighting, the need to conduct a temperature test shall be considered. 10. These Class 2 LED modules are only suitable for use in Canada, when marked with Class 2 input voltage ratings 42.4 Vdc or less for use in dry and damp locations, or rated 30 Vdc or less for wet locations. EVERBRITE LLC 4949 S 110TH ST PO BOX 20020 E131602 GREENFIELD, WI 53220 LED Modules, designated as Indoor Passively current limited (resistive) series, XXXXXXXX, where XXXXXXXX may be any combination of alpha characters. 1. These products are only suitable for connection to a Class 2 power source rated 60 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated greater than 60 V DC. 3. These products are each rated max. 60 watts per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. LED modules are suitable for use only in dry and damp locations with supply sources rated at min. 30 Volts DC to max. 60 Volts DC. 5. LED modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less. 6. These products may be secured in place in the end product by any means available. 7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall be considered. 8. LED modules rated for Class 2 input voltage of more than 42.4 V DC are only suitable for use in the United States. Neon "Animotion" controller, Cat. Nos. 800-0066, -0067 and -0068 41 SIGN COMPONENTS MANUAL (SAM)June 19, 2013 1. The Neon "Animotion" Controller shall be used within the ratings indicated above. Its input shall be powered by the Class 2 output of Model 800-0128 with the controller's output powering the input of Series "NuAUX" auxiliary transformers or the controller's input shall be powered by a Listed Class 11 high-frequency power supply. 2. The controller has been evaluated at maximum marked ratings with Neon Power Supply Cat. No. 1212 and Cat. No. 800-0065 auxiliary transformer. 3. The number of outputs on the controller may vary between one and eight. 4. No more than four outputs, with a maximum of two outputs per input, may be operated continuously. 5. All eight outputs shall not be on concurrently. 6. The controllers are intended for Indoor Use Electric Signs or shall be mounted in suitable enclosure when used with Outdoor Use Electric Signs. LED Modules, Sequencer Series Modules designated XXX-XXXX, XXX-YYYY or XXX-YYYYY (XXX-XXXX, XXX-YYYY or XXX- YYYYY may be any combination of alpha characters). 1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less. 2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2 circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be required. 3. Each module is rated and suitable for a maximum of 90 watts. 4. Sequencer modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less. 5. Sequencer modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less. 6. These modules should be secured by suitable means when installed in the end-use application. 7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require additional evaluation. 8. When the Sequencer modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these application are only suitable for use in the United States. LED Modules, Regulator Series Modules designated XXX-XXXX, XXX-YYYY or XXX-YYYYY (XXX-XXXX, XXX-YYYY or XXX- YYYYY may be any combination of alpha characters) 1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less. 2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2 circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be required. 3. Each module is rated and suitable for a maximum of 90 watts. 4. Regulator modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less. 5. Regulator modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less. 6. These modules should be secured by suitable means when installed in the end-use application. 7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require additional evaluation. 8. When the Regulator modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these application are only suitable for use in the United States. LCD Module, Model LCD v6.x with Power Supply. 1. These LCD modules are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. These LCD modules have not been evaluated for use and connection to a power supply source with- parameters that exceed Class 2 circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be required. 3. Each LCD module is rated and suitable for a Class 2 maximum 12 Vdc output of 43 watts. 4. The Exclusion of Water Test may be waived for this LCD module subassembly only when installed in outdoor location signs with Listed conduit and (QCRV) liquid light conduit fittings on primary circuits. 5. These modules should be secured by suitable means when installed in the end-use application. 6. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require additional evaluation. LED Modules, Cat. No. LCD v6.x with Power Supply. 1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less. 2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2 circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be required. 3. Each module is rated and suitable for a maximum of 90 watts. 4. Regulator modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less. 5. Regulator modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less. 6. These modules should be secured by suitable means when installed in the end-use application. 7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require additional evaluation. 8. When the Regulator modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these application are only suitable for use in the United States. EVERBRITE LLC E360604 SUITE 208 BLDG B 380 SEMORAN COMMERCE PL LED Modules, Models CST-20-B, CST-20-G, CST-20-R, CST-20-RGB, CST-2D-W, CST-30-A, CST-3D-B, CST-30-G, CST-3D- R, CST-3D-RGB, CST-30-W, CST-30-VWV, CST-40-B, CST-40-G, CST-40-R, CST-40-RGB, CST-4D-W 1.These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy limited circuit and is rated greater than 12V DC. June 19, 2013 SIGN COMPONENTS MANUAL (SAM) 42 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. EXCELLART SIGN PRODUCTS LLC 1654 S. LONE ELM RD E152309 OLATHE KS 66061 Frame system, Series EC(+) followed by -4, -4R, -6, -6R, -7, -7R, -8, -8R, -9, -9R, -12 Hinged and Standard, -D/F Hinged and Standard, -IDS, -S/F Hinged and Standard, or EC-S/F Access System. Accessories for use with EC frame systems, frame, angle, hat section, 6 in. radius corner, 9 in. radius corner, Cat. Nos. EC-4,-7,-8, EC-IDS, EC-Xtra, FF, FF-2, H-1, H-1.5, LC, LF, RR, or RRC retainers, Cat. No. EC-12 frame retainer brace, Cat. No. EC-S/F access system, Cat. No. EC lamp raceway, Cat. No. EC raceway cover, Cat. No. EC lamp/ballast track, Cat. No. EC-IDS raceway, Cat. No. EC Flex System for standard frame, hinged frame, or retro fit, Cat. No. EC-Tl, -T2 trim caps, or Cat. No. 1 1/2, 2 1/2, or H divider bars. Cat. Nos. F retainer, F hinged retainer, FF short retainer, EC-3.25 radius post, EC-3,25 rectangular post, EC-revel connector, EC-3.25 bleed frame, EC-8 in. radius quarter end, EC channel letter front, EC channel letter back, EC channel letter lid. Frame system Excellart (++) followed by C, C-2, M-C, or MC-R, for use with retainers MC- Alternate M-C, ZF.188, ZF.250, ZF-1 1/2, ZF-2, ZFC2 1/2, or ZFC-3. Frame system Narrowline, Cat. Nos. EC-4RN frame, EC-4N frame, 1 in. radius corner connector and cap. (+) Frames, angles, and hat sections have the same catalog number as the frame system. Frames available in standard or hinged versions. (++) Frames available in smooth or ribbed versions. Expanda Frame Model AMB13920. Lamp Socket Raceway and Cover Models AMB990 and AMB991. 1. When installed in an outdoor wet location application, consideration shall be given to conducting the water exclusion test of UL 48. 2. The suitability of the components to serve as wireways and electrical enclosures shall be determined in the end use. 3. When installed in an outdoor wet location, the bottom of the cabinet system shall be provided with at least two drain holes in each inside recess, except for the wireway. FANTASTIC DISPLAYS INC E362917 2049 S BAKER AVE ONTARIO, CA 91761 Class 2 powered LED modules, Cat. Nos. LMYX 225 [+], LMYX 324 [+], LMYX 220 [+1, LMYX 332 [+], LMYX 340 [+], LMYX 326 [+], LMYX 341 [+], LMYX 112 [+1, LMYX 120 [+], LMYX 102 [+], LMYX 117 [+]. 1. This product is only suitable for connection to a Class 2 power source, rated 12 Volt DC or less. 2. This product has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than electrical ratings. 3. This Class 2 LED module is rated as noted in the electrical ratings tables. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. This product is suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less. 5. This product is not required to be enclosed or protected from the weather in the end product. 6. This product may be secured in place in the end products by any means available. FEDERAL HEATH SIGN CO. LLC 4602 NORTH AVE E125271 OCEANSIDE, CA 92056 Sign face tensioning systems, designated "KLICK-RAIL" 1. Water exclusion must be determined in the end product. 2. Any frame dimension greater than 1.8m (6 feet) needs to be braced to prevent billowing. 3. This system limited to only decorative applications, and together with the flexible face material shall comply with the external decorative face requirements of UL 48, particularly the clearances from heat-generating components to decorative plastic panels. 4. The suitability of secureness of the clamp and flexible material shall be judged in the end-use application. 5. The installation of this system in a sign shall conform with the instructions provided with this tensioning system. Class 2 Powered LED Modules, designated RVI Series. 1. These products are only suitable for connection to a UL Listed or UL Recognized Class 2, DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED Illumination, RVI Series is rated 20 W per 2.7 m length with yellow LEDs and 21 W per 2.7 m length with Red LEDs. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 W per Class 2 circuit. 4. These products are suitable for use in dry, damp locations. When the Class 2 output is 12 Vor under, these products are suitable for wet locations. 5. These products are not required to be enclosed or protected from weather. Controller boards, Models PCB64PD, PCB32PD, PCB06PD. 1. The controller and drivers covered by this report are suitable for damp and dry locations only. 2. The controller Models PCB64PD, PCB32PD, and PCB06PD are suitable for use on a 120 V, 60 Hz service and are capable of switching up to 64,32, and 6 points, respectively. They are for use only with triac driver Models PCB20T6, PCB10T12, and PCB10T4. 3. The Model PCB20T6,6 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a maximum loadof13A, 1560W. AnA 41in! \J U 4/ i) -agagpt _ 13/ n. 1 v \ f L i i¢k:· ' L 11 A©AVE 71420 lvI - 4) £ b 1 1 AN- f /j .i :;i \\1 7 - tx - elt - . 4, N... t U. APPROVED .. PLANNiNG DIVISION , ;/ / / >097'MAS'fER 1.6,201 3-\102-EG ele-zone.04 e- 7 ANNER_p)DATV-a3-21:& FrR#.NSFERRED BY DATE· PLANNING INSPECTiON REQUIRED/77 3 ROUGH FINAL QUEZ ...00' NAME (714) . . TALD 1*gil_ 2 2Lt / LRETAIN PLANE f OR rU CURE REVISiONS·<S6lh:tA• saM)*BETQ*ils CHECKED AND Cd© TIONS BELOW:l 2-11 6. 1-7-10-f: 3, · ELYNO EXTE'' ., :.ALTERATiONS/MODIFICATIONS O ALL P.r.7 i. :· 19 TO MATCH EXISTING O SCREE.4.:1:2 02<19,RED ' Fl Rl Imt„';T I ANriACAPF PI ANR 17(21 Ch\}DITIONS: tron 2.95/ \ 1 A /\I I 180' /t 91 a ji Ali: Everbrite DISCLAIMER: Renderinos are for araohic ourooses ontv and not intended for actual constructondlmensions. For windload reauirements. adual dimensions and mountina detad. olease refer to ena:neenno soeafications and install drawinas. These-arawingsana-aesignsareinem:lusIveproperiyofEverEE-LEE-Use-of,oraupicaion:Iianymannerw,Inoui-expresswnlen-permissionoiveronreLLL#,spron,Diced. Customer: Taco Bell Project No: 297486 Scale: NTS Date: 7/1/13 ·Drawn By: RB Location & Site No: 1229 E. 17th St. Santa Ana, CA Site: TB20412 Description: Drive Thru Menu Board Revised: Revised: Customer Approval: NOTE: Unless specified by customer, all depth of embossing will be determined by Everbrite Engineering or existing customer specifications on file. Colors and graphics on file will be used unless otherwise specified by customer. Please read carefully, check appropriate box and fax O Sketch OK as is back to Everbrite:O New sketch required SIGNATURE DATE 11.5" 7.5" GENERAL SPECIFICATIONS: Materials: Aluminum sheets & steel tubes Decoration: Powder coat Taco Bell Bronze & black Arch & Bell Area Squared: 9.29 Sq. Ft. Menu Board Area Squared: 44.50 Sq. Ft. Weight (Est.): · 745 lbs. (crated) · 595 lbs. (uncrated) ELECTRICAL Illumination: · White LEDs Power Supplies: · (2) 062-00008 Electronic LED Power Supplies Line Load: · 1.92 amps @ 120 vac-60Hz · (1) 20 Amp circuit FRONTVIEW SCALE: 1/2"=1'-0"33,0" 1 COLORS:SIDE VIEW SCALE: 1/2"=1'-0"Exterior: Doors & Mullions: Powder coat Taco Bell Black - 9"Cabinet: Powder coat Taco Bell Bronze . E-4.07 -2,04-1.0 BASE PLATE DETAIL L- 1.0" thick SCALE: 1"=1'-O'0 - L 6" J These product sheets are th• exclusive propefty of Everbrite LIC. Use of this property in any manner without express written permission of Everbrite LLC is prohibited. Drawings arn for gra#hic Arposes only Ind notintended for actual construction. For mole specijic manufactuling detail, please refer to engineeling specilications and install drawk,gs. Everbrite LLC Part No: E003535P Project No: 291388-2 iCl: Everbrite 2Zna 4 1 YA9.%1G.refanx : 4 Ul|23729 Drru Evolution LEDVE Menuboard Fl-BJCM M : wi Date: 2/12/13 Website: www.everbrite.com :with Arch -6712@77 1 |lk>f [mE[L[L 91.375" 72,0" 18.584" 70..131 15.994" 8.4375 8'-2 45' 1 8'-11 .17 1/4'. ,ILLUMINATED EXTENDER 1'11:263/8'MT'G DETAIL TOP V[EV MAX 1'35 1 - -0 ILLUM1'-11 7/16'8 TOPPI SINGLE ILLUMINATED EXTENDER TAC 67 7/16'El.BEL 5-4'AACk 15. 1/4' , , r-91/4, 3 5/16" DIA.TRIPLE HIGH EXTENDER LOGO DISPLAY liT'G DETAIL TIP VIEW -UFTING ANGUE IATED / -ER -lI--ILLINATED TOPPER TRIPLE IT'G DETAIL SIDE VIEW0 HIGH.L EXTENDER - 61-5 7/16· 111 15' LAMPS: (1) F72T12 CW/HO BAUAST (1) 51-742-R/256-248 INSTALLER INSTRUCIIONS 1.. STAKE FOUNDAION AREA AND. CONFIRM FINAL GRADE REQUIREMENTS WITH G.C. 2. EXCAVAIE FOUNDATION AREA. 3. SET ANCHOR BOLTS CAGE PWMB,INSTALL CONDUIT SlUBS AND POUR CONCRETE. (PRIMARY ELECEICAL SERVICE TO BASE BY G.C.) 4. ALLOW CONCRETE CURE TIME AS REQUIRED. 5. INSTALL SIGN ON ANCHOR BOLTS. LEVEL SIGN AND GROUT AROUND ANCHOR BOLTS. 6. REMOVE UFRNG BRACKET AND REINSTALL BOLE 7. CLEAN UP AREA AND REMOVE ANY PACKING MALL NOTE: INSTALLAIION 1,1TG OF UUM TOPPER, ILLUM & NON ILLUM. EXTENDERS, AND ILLUM TRIPLE EXTENDER. SEE DWGS. IN00152P, & IN00886B DESIGN SPECIFICATION: 3000 P.S.I. CONCRETE .33 CU. YDS. TOTAL- IVIll/V 6'-8'BOARD SINGLE NON-ILLUM. EXTENDER - t L - -- r -- 3]11Ir 1'-4.3' X 3' TURE- 1" 1 5'-0'I 3/4'-10 X 20 1/4' LG. ANCHOR BOLTS W/4* HOOK &50 THRD LINGIH (4) REO'D I.............. ELECTRICAL DATA: MENU BOARD: LAMPS: (4) F60T12 CW/HO BAUAST (1) 6G3959 2.9 AMPS TOPPER: LAMPS: (1) F24T12 CW/HO BAUAST (1) 51-609-XR/256-148 .55 TOTAL MIPS MENU BD EXTENDER LAMPS: (1) F42T12 Cw/liD BAUAST O) 51-609-XR .55 TOTAL AMPS 0) 15 AMP CIRCUIT 120V REQ'D 1RIPLE HIGH EXTENDER .90 TOTAL AMPS (1) 20 AMP CIRCUIT 120V REQ'D -10 1 2-0 -7T 'Cl 12- MIN 2 CODE e ELECTRICAL CONDUIT BY OTHERS.l« ANCHOP DAIT \PROJEC CUT 161/4 1 DULI mON 4.9 AMPS TOTAL (fOR SIGN LIGHTING) i »f 1 OUTLINE OF BASE COVER FRONT OF SIGN ANCHOR BOLT & CONDUIT SETTIN6 LOCK VASHER (SCALE FULL ) FLAT VASHER \ SWITCH GRADE LIEY»l) b DESIGN NOTES: 1.9GN, AND BASE ARE DESIGNED TO WITHSTAND A MID LOAD OF 30 P.S.E 2. ALL CONCREIE EXCEPT CONCRETE USED FOR BACK ALL SHALL DEVELOP A MINIMUM COMPRESSIVE STRENGTH OF 3000 P.S.1 3. CONCRETE BASE DESIGNED USING GOOD TO AVERAGE SOILS HAVING AN ALLOWABLE CAPAQTY OF 400 P.if./FT. 4. ALL FOOTING EXCAVAMNS ARE TO BE FREE OF WATER AND FOREIGN MATTER BEFORE PLACING CONCRETE. 5. IF THESE SOIL CONDITIONS ID NOT EXIST AT THE FOUNDATION UIATION IT IS THE ERECT[R'SRESPONSIB]LITY TO NTIFY EVERBRITE, INC PR][R TO PERFORMING ADDITIONAL EXCAVATION [R ANY CONCRETE PLACEMENT, MAIN MENU BD. E 00036BR TOPPER PVD 20065 SIDE MENU BD. PVD 20179 MNBD. EXTENDER E 00098B 71. ... 4.1· · These drawings ore the:91 Everbrite exclusive property of Everbrite, Inc.LEVELING-->Ar·>® 4949 so. 110th St.| 1'-6' DIA | NUT . FER PILE IS LEVELED AND P.O. Box 20020 Use of, or dupligation in any mannerPOLTED INTO PLACE, nLL ENTIRE AREA UNDER PLATE WITH STRUCTIRAL Greenfield, WI 53220 without express written permission hON-SHRINK, NON NETALIC COENTIT[OUS 414-529-3500 of Everbrite,Inc. is prohibited. GROUT, FOLLOW ALL [F THE MA,UFACTURERS ITLE A RELEASE TO INSTALL 5-27-03 PJL INSTRUCTIONS FIR ALL GROUT MIXING,TACO BELL OUT DOOR MENU BD PLACEMENT, AND CURINGSYMDESCRIPTIONDATECHGECN DRN HED DT 5-27-03 SCALE DRWO NR 'REV REVISION RECORD CKD PIL OT 5-27-03 1:30 IN01340B A 1\-13-13 1329 E }11« 9\-- 4 disconnect for the monument sign(s) isrequired or the dedicated circuit breaker(s) mustbe individually lockable in the off position. CEC 600-6ss to any power supply in attic or abovefromceiling shall be immediately a ladder or Accewith a2x3 foot access door & passage with-inch walkway. CEC 600-21 (d)(d) 12City of Santa Ana Plarining & Building Agency - "-E>h¢7? ELECTRICAL 1 PLAN APPROVAL This set of plans and specifications must be kept on the job at all times and it is unlawful to make anychanges or alterations on same without written per- mission fronj the Department of Building Safety City of Santa Ana. " PERMIT TYPE:((39 %%5r MECH ARADING PERMIT# b\99234 /£201 5519.3q OCC. GROUP --f CONSTR. TYPE - CODE EDITION 2.01(3 FLOOD ZONE The approval of this plan and speclfications SHALL |NOT*eld to permit nor be an approval of the FLOOD ZONE CERTIF. REQ'D YES 490-vioiauort'or any provisions of ANY City Ordinance or stastaw. . MICROFILM YES 32K12*2> Approad y RADIANT BARRIER @ ROOF YEO CITY OF SANTA ANA RESIDENTIAL DEV. FEE YES /wd>DEPARTMENT OF BUILDING SAFETY 2 SCHOOL DISTRICT YES <44 62;14. · ./ . , . e