Loading...
HomeMy WebLinkAbout10180583_1313 W. 17TH #A - Plan (2)1 -·-/88*'-i T)Vi. 72111 Planning & Building Agency Building and Safety Division 6 20' Civic Center Plaza P.O. Box 1988 (M-19)ELECTRICAL SIGN 0 Santa Ana, CA 92702 (714) 647-5800 REQUIREMENTS www.santa-ana.org Code references are to the 2010 California Electrical Code (CEC) All signs require Planning Department approval. All electrical signs require electric plancheck and permit. 1. Manufacturer's instructions are required at the time of submittal C-11: 3-21-2011 2. Submit detailed installation instructions including diagrams to the Building Department for plan review at the time of submittal, Plans must include appropriate items noted by this bulletin. 3. Cash or surety bond in the amount of $200.00 is required at time of issuance for each address. The cash or surety bond will be refunded after all required finals. A building permit is also required - except for open or highlight neon lighting. Installation Requirements: CONTACT FIELD INSPECTOR PRIOR TO SIGN INSTALLATION. (SEE SECTION G OF THIS BULLETIN) 1. Conductors and equipment shall comply with California Electric Code Article 600. 2. All metal parts of a sign shall be bonded in the manner specified in Article 250. Isolated metal parts are permitted to be bonded by using an external green insulated conductor. Equipment grounding & bonding conductors must be sized by 110.26 and protected from physical damage. Minimum size is 14 AWG. CEC 600.7 3. A listed disconnect switch in the power supply primary, shall be installed within sight Of sign or have permanently installed means for locking in an "OFF" position. This is also true for a transformer enclosure. CEC 600.6 4. A listed receptacle or an approved termination device shall be used for each neon electrode. To relieve stress at terminations, tubing shall be supported with listed tube supports in an approved manner within six inches of electrode connection. CEC 600.41 & 600.42 5. Every electric sign of any type shall be listed by an approved testing laboratory and shall be installed in. conformance with this listing. That includes "l of x", "2 of x" labeling for each separate unit of a multi-unit sign. CEC 600.3 6. All "can" letters and transformers housings shall have section labels that are readily visible after installation. CEC 600.4 7. Transformers shall be located where accessible and be securely fastened in place. Page 1 of 2 01 - When not inside the sign, they need a 3 foot high x 3 foot wide x 3 foot deep workspace. Transformers are permitted to be located in attics or canopies provided there is a passageway at least 3 feet high x 2 feet wide with a minimum; 12 inch catwalk/walkway from the point of' entry. Transformers must be securely fastened and independent of T- bar when above a suspended ceiling. No part of sign may be fed with flexible cord when located above T-bar ceilings. CEC 600.21(E&F) & 400.8 8. Adequate illumination shall be provided for all working spaces about electrical equipment. This applies to attics and canopies when entry is required to service or inspect the equipment. At least one switch is required at entrance. CEC 110.34 & 600.21 9. Doorway to an attic or canopy space shall be minimum 3 feet by 2 feet wide. CEC 600.21(E) E. Open neon outline or highlight lighting. 1. To be treated as a sign by this department. However, Section D-5 & D-6 of this bulletin will not apply. 2. Neon tubing shall be located where not normally exposed to physical damage. Open neon tubing below 9 feet shall be protected from physical damage by an approved shielding method. CEC 600.30 and 110.34(E) F. Light-Emitting Diode (LED) Signs 1. Will be treated as a sign by this department. All sign rules in sections A, B, C, D, F, and G will apply as appropriate. 2. LED illumihation for signage must be a listed or recognized component. Many LED manufacturers specify particular brands and models of transformers some do not. Manufacturer information to clarify this issue is required on LED sign plans. 3. Unlisted LEDs may not be used in an electrical sign or as permanently installed illumination. 110.3 4. Please have packaging or catalog cut-sheets on hand for inspector to review when LED modules do not bear listing symbols. G. Inspections 1. Contact an Electrical Inspector one (1) workday (minimum) in advance of installation to arrange a site meeting on dav of installation. 2. Call for inspection Monday through Friday, 8:00- 8.30 a.m. at (714) 647-5821. Approved prints and the job card must be on site for inspectjon. Page 2 of 2 51 SIGN COMPONENTS MANUAL (SAM)October 1, 2013 LED 60CV 12P 100- 277 0.8 - 0.3 12 60 LED 60CV 24P 100 - 277 0.8 - 0.3 || 24 | 60 3. These power supplies are only suitable for use in dry and damp locations. 4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Lighitech'M t Lightech m LED Driver 0 Halogen Tionkrmer and model designation.Company name or trademarks GE LIGHTING SOLUTIONS LLC BLDG 338E 1975 NOBLE RD E219167 EAST CLEVELAND, OH 44112 USA Border tube kits, Includes Lens Cat. No. GExxBTL: Lens connector Cat. No. GExxBTLC; End cap Cat No. GExxBTLEC: Exterior corner kit Cat. No. GExxBTLXC; Interior corner kit Cat. No. GExxBTLIC: Base'reflector Cat. No. GEBTBR; Base connector Cat. No. GEBTBC; Cam lock Cat. No. GEBTCL. Canopy Kits, Cat. No. GECPL (8 ft length), GECPEC (end cap), GECPLC, (lens connector), GEBTBCL, GEBTBC. Light guide kits includes: Light guide Cat. No. GEXNLGXX-XXX, Light Guide End Cap Cat. No. GEXXXNLGECZZ, XXX may be any alpha letter representing color. ZZ may be any alpha letter representing size. Light Guide Connector Cat. No. GEXXXNLGYZZ, XXX may be any alpha letter representing color, Y can be any alpha character describing the type of connector. ZZ may be any alpha letter representing size. Mounting clip Cat. No. GEXNMCXX, Supply wire Cat. No. GEXNSXX: Splice connector Cat. No. GEXNSC 1 : Weather box Cat. No. GEXWBXX-XXX. 1. Border Tube Kit, Canopy Kit and Light Guide Kit are for Wet Location only use when enclosing LED's connected to a Class 2 circuit operating at under 30V continuous DO, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. 2. The LED border tube kit and Canopy Kit was not evaluated as an electrical enclosure. 3. The LED border tube kit and Canopy Kit was not evaluated as a watertight housing. LED power supplies, Cat. No. GEXLPS21, GEXNPS30-120, GEXNPS31-120 1. This component has been judged on the basis of the required spacings in the Sta dard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2.The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3.The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40 C. 4. Leakage current measurements shall be. performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment ih the end-use product. 5. The drivers are intended for installation inside an electrical enclosure. 6. The ground connection rs not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. 7. The drivers are-suitable for dry location use only except the drivers Models GB<NPS30-120 and GEXLPS21 are suitable for damp location use. LED array drivers, Models GEXLPS21-U, GEPS12-60U, GE060/MV&'12T12T1-A. 1. These components have been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Foorth Edition, which would covef the component itself if submitted for Listing. 2. The terminaJs and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. The insulation system of the main isolation transformer designated (T2) in these models is a Class 105(A) insulation system. Unless the modules are mounted as specified in condition of acceptability number 7, a temperature test is required when these models installed within an electrical enclosure or raceway. 5. The maximum measured leakage current of a single unit is 0.49 mA. Leakage current measurements shall be performed when multiple LED drivers are used in the final equipment or when the LED driver is used ih combination with other equipment in the end-use product. 6. The unit is intended for installation ihside an electrical enclosure. 7. The unit may be used within an electrical enclosure or raceway without temperature test pfovided they are mounted not closer than 1 in. end to end or 4 in side to side from adjacent LED power supplies. 8. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. LED power supplies, Model GEPS24-100U, GE100/MV/\/24T1-A 1. This component has been judged on the basis of the required spacing in the Standard f0r Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40 C. 4. This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an electrical enclosure or raceway. 5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 6. The unit is intended for installation inside an electrical enclosure. 7. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. LED array drivers, Models GEPS 12-20, GEPS 24-20. 1. The maximum measured output voltage, current and power at the output of these models was found in compliance with the limits for Class 2 output requirements. 2. The transformers of these units employ Class 105 insulation system. 3. These components were intended for use in indoor Dry and DAMP location only. October 1, 2013 SIGN COMPONENTS MANUAL (SAM) 52 4. In the end product, power supply spacing to other heat producing comp0nents shall be minimum i2 ihches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in, in any other direction. 5. These components shall be installed inside an electrical enclosure. 6 Input and Output leads are style 1316, rated 600 V, 105 C, VW-1. Minimum No. 18 AWG. The suitability ofinput and output connections shall be determined in each end use application. 7 The maximum room ambient temperature permitted by the manufacture is 60 C. The temperature measured on outside enclosure of Models GEPS24-20 and GEPS12-20 are 67.2 C and 77.9 C respectively. The necessity of repeated Temperature Test shall be determined in each end use application if minimum thermal spacings in accordance with Item 4 are not provided. LED Dimmer, Model GEDM 1 and GEDM 1-A. 1 This component has been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The equipment was submitted and tested for a maximum manufacturers recommended 'ambient (Tmra) of 40 C. 3. The unit is intended for installation inside an electrical enclosure. 4. This unit is provided with a Class 105(A) insulation system. The unit may betused within an eleckical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 im. side to side from adjacent LED power supplies. 5. The Xitanium Dimmer is ionly suitable for use in Class 2 circuits powered by Advance LED drivers with maximum input rating of 24Vdc, 4.l A, or 12VDC, 5A. Dimmer circuit is 0-10VDC: 6. This LED Dimmer Controller muit be used with either a 100K Ohms Potentiometer or a standard 0-10 V DC dirnmer switch. 7 For dry or damp location. LED Strips, Class 2, Cat. Nos. GE-XX-XX-X-XXX, GE-XX-XX-XX-XXX, GE-XX-XX-XXX-XXX, GE-XX-XX-XXXX2XXX, GE-XX- XX-XXXXX-XXX, GE-XX-XX-XXXXXX-XXX, GE-XX-XX-XXXXXXX-XXX, GE-XX-XX-XXXXXXXX-XXX, GE-XX-XX- XXXXXXXXX-XXX, catalog numbers may vary per nomenclature. GE followed by: ''XX" representing color: RD, RC, YG, GL, SB, BL, WH, YA, VWV, GR, PO. followed by: "XX" representing product line: CL, DS, XL. PT, XN. TM, MX, TU, PG, PX, PH, XH, MH, SS, PM. MM, MH, BS, BD, BI followed by. "X" to "XXXXXXXXX" representing light strip final assembly or number of LEDs per foot: LA, LE, AA, SX, LX, WXX, TXX, PX, XX followed by: ''XXX" denotes any alphanumeric character that represents the color temperature of the LEDs. Cat. Nos. GE-AA-BB-CC, where'AA" may be DS, XN, XNL, XNA, MX, MXL, PG, MM, MMD, SS, PM, PMD, MXH, MXHL, BS, BD, Bl, BIH, BSH, BDH, DSH or SSH which represent product line: "BB" may be RD, RC, YG, GL, SB, BL, WH, YA, WW, GR, PO or any alphanumeric character; and -CC" may be any alphanumeric characters or blank. 1- These products are only suitable for connection to a Class 2 power source. 2. When units are connected to a Class 2/ LPS circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2/ LPS supply. 3. These products are suitable for use in dry, damp and wet locations. 4. These products described in this section may be cut into segments per manufacture insulation instructions. 5. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 Conditions of Use as defined in the Sign Components Manual. 6. The Light Guide has notbeen evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end use product. NOMENCLATURE: Nomenclature for LED Strip Light: GE-XX-XX-X-XXX, GE-XX-XX-XX-XXX, GE-XX-XX-XXX-XXX. GE-XX-XX-XXXX-XXX, GE-XX- XX-XXXXX-XXX, GE-XX-XX-XXXXXX-XXX, GE-XX-XX-XXXXXXX-XXX, GE-XX-XX-XXXXXXXX-XXX, GE-XX-XX-XXXXXXXXX- XXX. First Set of "XX" = denotes the color of the LED RD = Red family RC =Red/Orange family YG = yellow family GL =Green family SB, BL = Blue Family WH = White YA = Amber VAN = Warm White GR =Green PO = Portland Orange Second Set of "XX" = denotes product line CL = channel letter DS = double sided Power Strip XL =tetra long strip PT = power tetra XN. XNL, XNA =Contour or Contour LS TM =Mini MX. MXL = Max TU = Ultra PG =Power Grid PX = Power White XL PH = Power White HO XH = Power White XL HO MM, MMD =Mini Max SS = Power Strip 53 SIGN COMPONENTS MANUAL (SAM)October 1, 2013 IPM, PMD = Power Max |MH, MXH. MXHL =MAX HO 1 BS = Shallow Box single sided 1 BD = Shallow Box double sided 1 BIH = Edgestrip Third set of "XX" denotes Light Strip final assembly as noted below: LA = | Light Strip. assembled inside a plastic rod, 8 inch section LE = 'Light Engine means same as Light strips AA =Light engine, assembled inside a plastic rod, 16 inch section SX or X =Number of LEDs per foot where Xisl =6 LEDs per foot etc. (X can be representative of lt09 digits) V\D<X -0/ide Angle light diffuser, where the first X describes the PCB length, A for regular and L for long, and the second X is an alpha numeric character of leds per foot PX =For PowerGrid (PG). Power Strip (SS) and Double Sided Power Strip (DS) only, where x eqwals the number of LEDs per foot Not Assembled in Tube. An optional X may be added to denote wirei length between modules where X is S for short, M for Medium, and L for Long. XX =only to be used with DS product line, xx is number that correlates to total length in inches (48 = 48") assembled in acrylic tube. "XXX" denotes any alphanumeric character that denotes the Color Temperature of the LEDs i.e. 65k = 6500,75k = 7500 etc. Splice connector, Cat. No. GexxSCx; End caps, Cat. No. GexxECx. 1. These products are only suitable for connection to a Class 2 power source. 2. When units are connected to a Class 2/"LPS" circuit, they are not to draw a total wattagej of greater than'the secondary or output rating of the Class 2/'LPS" supply. 3. These products are suitable for use in dry, damp and wet locations. 4. These products described in this section may be cut into segments per manufacture insulation instructions. 5. Units may be provided with UYMR2,3M type VHB double-sided adhesiveJtape. Tape must be utilized per UYMR2 "Conditions of Use" as defined in the Sign Components Manual. 6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end use product. LED Controller, LED Tetra FX Special Lighting Effects Controller, Cat. No. GEFX1 1. This product is suitable for only when connected to a Class 2 power source or LSP, Model GEXLPS20, GEXLPS21, GE)(NOS30 or GEXNPS31 by GE. Rated Input is 12/24 Vdc, Output is 12/24 V dc. 2. This product is a Class 2 device suitable for use in dry, damp and wet locations. 3. The controller shall be provided in a suitable housing when use in wet locations. 4. Lead wires are R/C (AVLV2), Style 2651, rated 105 C, 300V. Not suitable for use inside wallb, above ceiling or other similar concealed spaces unless mounted inside an electrical enclosure. 5. The controller is provided with a DMX 5-pins input connector. The pin arrangements in the connector shall always be the same. The DMX controller is capable of providing the 4 channel dimming, flashing, chasing, sequencing, color mixing, and color changing functions. LED wire, Cat. No. GExxSWx. Nomenclature for Splice Connectors, LED Wires, End Caps: ¤ denotes product line, CL = channel letter., DS = double sided, XL = tetra long strip, PT = power tetra, XN = Exposed Neon, TM = Mini, MX = Max, TU = Ultra, PG = Power Grid, PX = Power White XL, PH = Power White HO, XH = Power White XL HO, MM = Mini Max; 'x' denotes design revision number. 1. These products are only suitable for connection toi a Class 2 power source. 2. When units are connected to a Class 2/"LPS» circuit, they are not to; draw a total wattage of greater than the secondary or output rating of the Class 2/"LPS" supply. 3. These products are suitable for use in dry, damp and wet locations. 4. These products described in this section may be cut into segments per manufacture insulation instrOctions. 5. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions of Use" as defined in the Sign Components Manual. 6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end use product. LED power supplies, Models GECLPS4. 1. LED power supply, Catalog No. GECLPS# for dry and damp locations. 2. Each power supply output is Class 2. LED power supplies, Models GECLPS4D. 1. LED power supply, Catalog No. GECLPS40 for dry and damp locations. 2. Each power supply output is Class 2. LED power supplies, Models GECLPS6 and GECLPSPHA. 1. LED power supply, Catalog No. GECLPS6 for dry and damp locations. 2. Each power supply output is Class 2. LED power supplies, Models GECLPS3 1. LED power supply, Cat- No. GECLPS) for dry and damp locations. 2. Each power supply output is Class 2. LED power supplies, Models GECLPS5, GECLPSPH, GECLPSPW, GECLPSWH. 1. LED power supply, Cal. No. GECLPS5, GECLPSPH, GECLPSPW and GEOLPSWH for dry and damp locations. 2. Each power supply output is Class 2. Power supplies with Class 2 outputs, Models GEPS24-80, GEPS12-60, GEPS24-20. 1. These components are intended for use in dry locations only when not potted. When,potted, they are suitable for damp locations. 2. These power supplies Aeed to be installed in an enclosure with a means for the connection to conduit. 3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than 13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110°C. Similarly, for Model October 1, 2013 SIGN COMPONENTS MANUAL (SAM) ;54 GEPS24-20, a terhperature lest is requiced when installed in an enclo'sure smaller than 13.5 by 6 by 4 inches, but the maximum temperature on the output transformet by thermocouple is 90°C. 4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet„ locations. Power supplies with Class 2 outputs, Model GEXNPS30. 1. This component has outputs thal qualify as being Class 2. 2 These components are intended for use in dry location only. 3. The transformer employs a Class B (130) Insulation Syitem. 4. These components shall be installed in compliance with therenclosure and mounting requirements of the ultimate application. 5. The maximum room ambient temperature permitted by the mahufacture is 50(C. 6. A Temperature Test is required oflthe power supply installed in an enclosure that measures less than 13.5 by 6 by 4 inches. The maximum temperature on the output transformer by thermocouple is 110( C. Power supplies with Class 2 outputs. Models GEPS24-180U, GE 180/MVA/24T1-C 1. The maxirnum measured output voltage, current and'power at the output of these models was found ih compliance with the limits for LPS output requirements and additionally evaluated to comply with Class 2 output criteria. 2. The transformer employ Class 8 insulation system. 3: Power Supply is intended for use in indoor Dry and Damp location only. 4. In the end product. power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in any other direction. 5. Input and Output leads are style 1316, rated 600 V, 105°C, VW-1. Minimum No. 18 AWG. The·suitability of input and output connections shall be detefmined in each end use application. 6. The power supply was submitted and tested for a maximum manufacturers recommended Tc p.oint described in the table below. If adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. iside to side a temperature test shall be ;conducted irittle-eptuse product. IModel Input Voltage, HZ Max. Case Temp @ Tc, °C | Ambient, °C GE180/MVA/24T1 -C, GEPS24-100-277,60 80 60 180U LED Light Engine, Cat Nos. 11'10-WH-ZZ-TTK, 1110-RD-ZZ-TTK, catalog numbers where: "ZZ" representing assembly version: followed by: "TT" - Optional - represents the color temperature of the LEDs in degree "K" Kelvin. Cat. Nos. 1 11'1-XX-ZZ-Y-TTK, catalog numbers may vary per nomendature.: DOC representing color: RD, RC, YG, GL, SB, BL, WH, YA, WW, GR, PO: "ZZ" representing assembly version, "Y" representing number of LEE)s, followed by: "TT' - Optional - represents the color temperature of the LEDs in degree "K" Kelvin. 1. These products are only suitable for connectioh to a Class 2 power source. 2. When units are connected to a Class 2/"LPS" circuit, they are not to draw a total wattage of greater than the secondary oroutput rating of the Class 2/"LPS' supply. 3. These products are suitable for use in dry, damp and wet locations. 4. The suitability of the; LED Light Engine mounting means shall be determined in the end-use application. 5. The suitability of the LED Light Engine to be used Without an additional electrical enclosure shall be determined in the end-use application. 6. These products described in this section may be cut into segments per manufacture insulation instructions. 7. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape ;must be utilized per UYMR2 "Conditions of Use" as defined in the Sign Components Manual. LED Driver with Class 2 Output, Models GEPS12D-60U, GEPS24D-80U. 1. These LED Drivers have been evaluated to Class.2 output requirements for dc circuits with a maximum of one Class 2 output. 2. These products are provided with the following electrical ratings: ]Model No.Input Voltage (V Input Freq Input Cuffent Output Voltage Output Current Output I ac)(HZ) (A) 6/ dc) (A) Power (W) GEPS240-BOU 100-277 50/60 1.1 24 3.3 80 [GEPS 12D-60U 100-277 50/60 0.85 12 5.0 60 3. The load powered by the Class 2 output of the LED drivers are suitable for use in dry, damp and wet locations. 4. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, aid minimum 2 inches spacing to top of enclosure. 5. In the end' product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less than 4 inches (102mm) apart when arranged otherwise. 6, These products shall be enclosed in the end product. 7. The unit is intended for being used in.permanently wired signs. 8. The suitability of output leads, rated No. 24 AWG minimum, rated 80°C minimum, 600 V, shall be determined in end product use. 9. These units may provided with Dimming Input (Purple and Gray wires) to control output current range, the suitability shall be determined in each end-use application. 10. These products are intended for use in dry and damp locations LED Driver with Class 2 Output. Model 1 110PS-60S. 1. These LED drivers have been evaluated using resistive load fesulting in the electrical input and output noted on page 1. 2. These LED drivers are provided with Class 2 output. 3. These LED drivers are intended to be operated in a maximum ambient '(Ta) noted as below: Model - Ta ('C) | LD-60-UV-1214V 40 4. These LED drivers are intended for use in dry and damp locations except that models LD-60-UV-1214V and LD-60-UV-1214V- SC are suitable for dry location only. 5. These LED drivers are provided with 18 AWG AWM input amd output leads. The suitability of the wiring and the, need for a suitable enclosure shall be considered in the end product. 55 61;GN COMPONENTS MANUAL (SAM)October 1, 2013 6. These LED drivers are intended to be operated on a maximum 20 A branch circuit. 7. The need of the grounding means shall be determined in the end product. 8. These LED drivers shall be enclosed within a suitable end product enclosure. 9. For model LD-60-UV-24\ADIW, the conduit knockout test was not conducted. The suitability is to be determined in end product. 10. In the end product LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 11. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apan when=arranged end-torend, and not less than 4 inches (102rnm) apart when arranged otherwise. LED Driverwith Class 2 Output, Model GEPS12-180U. 1. The output (Red/Black) of each unit complies. with Class 2 criteria of UL 1310. 2. The device is provided with 18 AWG input and output leads. The suitability of input and output connections shall be determined in end-use application. 3. The suitability of grounding imeans shall be determined by end product. 4. The device is not intended for field wiring used. 5. The device is intended to be connected to a maximum 20 A branch circuit 6.;The devices are of the constant current type that requires the proper number of LED modules and controllers that does not exceed the maximum output voltage/current. 7. The measured maximum external enclosure temperature (Tc) is 77.2 degree C when the roomembienttemperature are 60 degree C. The suitability shall be determined in end application. 8. The devices employ input surge suppression protection, Cat. No. S14K385E2K 1 under UL File E321 T26, which is intended end- use SPD type 2. The suppressed voltage rating is 385 Vac. The surtability of use of this component shall be determined in the end-product application. 9. No mechanical test has been conducted for the models and the metal chassis is considered as dead metal. The devices shall be mounted in the intended manner in an eridosure, having adequate strength and thickness with acceptable spacing being provided. 10. The device has been evaluated for dry and damp locations use only. 11. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 12. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-enid, and not less than 4 inches (102mm) apart when arranged otherwise. LED Driver Extended Enclosure, Model No. GEPSJB60. 1. The J-Box extended enclosure has been evaluated only for use and connection to LED Class 2 Drivers Models GEPS12-60, GEPS12D-60U, GEPS24-80, GEPS24D-80U, GEPS12-60U-NA, GEPS12-60U-GL, GEPS24-100.U-NA, and GEPS24-100U GL.2. These products complete the electrical enclosure when installed over the primary wiring of the LED driver. 3. The suitability of the mounting shall be determined in end use application. 4. The enclosure has been evaluated only for use in Dr'y and damp locations 0nly 5. Supply connection shall be determined in the end used application. 6. Ground Screw size is No 6 thread forming screw with cupped washer is provided for grounding. The maximum size ground wire that can be used is 14AWG. The maximum size branch circuit that the units can be connected to is 15A unless a 16- 14AWG six inch pigtail lead supplied by sign company is connected to ground terminal and then spliced to 12AWG ground wire of a 20 A branch circuit. 7. Cover Screw shall not be of a thread forming or self-tapping type. 8. To keep the enclosure from rotating, the Enclosure shall be secured by at least one mechanical fastener. 9. The J-box has been evaluated for an ambient of 40°C. 10. The J-box label shall be marked for a 759C supply wire connection. LED Driver with Class 2 Output, Cat. Nos. G EPS 12-60U-NA, GEPS 12-60U-GL, GEPS24- 100U- NA and G EPS24-1000 -GL. 1. These power supplies are provided with Class 2 outputs 2. These products with Class 2 outputs are suitable for use in dry and damp locations. 3. Model Nos. GEPS 12-60U-NA, GEPS12-60U-GL have been tested in an oven at max. 40°C ambient and Model Nos GEPS24- 100U-NA, GEPS24-100U-GL in an over at max. 55 °C. Maximum case temperature at (Tc) for all models should not exceed 85°C. 4. The suitability of grounding connection shall be determined in the end-use product. 5. These products shall be enclosed in the end product. 6. These products are provided with the following electrical ratings: Model Input, 50/60 Hz Rated Output V A VDC A DC W GEPS12-60U-NA,120-277 Max. 0.65. 12 5.0 60GEPS12-60U-GL, GEPS 12-60U-NA, 120-277 Max. 1.10 24 4.0 96 GEPS12-60U-GL 7. These products are suitable for factory wiring only. 8. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end to end and 101.6 mm (4 in.) from side to side. 9. The suitability of input/output leads andthe wring shall be determined in end product use. 10. These LED drivers are intended to be operated on a maximum 20 A branch circuit. 11. These products shall be enclosed in the end product. LED Driver with Class 2 Output, Model GEPS24-180U-GL. 1. The device shall be used within Recognized ratings as specified above. 2. Each output of the unit complies with Class 2 criteria of UL 1310. Multiple output units may exceed Class; 2 when the output terminations are interconnected. Do not interconnect output terminations. 3. The device is provided with 18 AWG input ahd output leads. The strain relief test was not conducted on thjs device. The suitability of input and output connections shall be determined in end-use application. October 1, 2013 SIGN COMPONENTS MANUAL (SAM) 56 4. Temperature Test has been conducted using resistive loading, and the LED Driver was mounted on a heat sink, alurninum, approx size 500 mm by 300 mm by 100 mm. The measured maximum external enclosure temperature (Tc) is 79.4 °C'when the room ambient temperature is 60 °C. The suitability shall be determined in end application. 5. Transformers employ Class 130(B) insulation system. 6. The suitability of grounding means shall be determined by end pfoduct. 7. The device is intended for factory installation only. 8. The device is intended to be connected to a maximum 20 A branch circuit. 9. The devices are of the constant current type that requires the proper number of LED modules and controllers ;that does not exceed the maximum output voltage/current. 10. The device has been evaluated for dry and damp location use only. GEMINI INC E16382 103 MENSING WAY CANNON FALLS, MN 55009 Plastic Channel Letters, Cat. No. Plastic Channel Letters. 1. The channel letters may be used as an electrical enclosure when provided with sign face material in the end-use application that is suitable for electrical enclosure use. 2. The neon tube shall bespaced a minimum of 1/8 in. from the inside walls of'the plastic enclosure, and 1/8 in. from thetsign face. 3. Openings for drain holes, conduit, electrode receptacles and mounting shall be provided in accordance with the Standard. 4. The channel letter plastic is rated 80°C. 5. For outdoor or indoor use. 6. Spacings from the channel letter to the enclosure for neon transformers or power supplies shall be in accordance with Standard UL 48. Plastic Channel Letters, Plastic Indoor Channel Letters. 1.The channel letters have been evaluated for indoor application only. 2.The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. Openings for conduit, electrode receptacles and mounting shall be provided in accordance with the Standard. 3.The channel letter plastic is rated 50°C. 4. The channel letter may be used as an electrical enclosure when provided with a sign face material in the end-use application that is suitable for electrical enclosure. 5. Spacings from the channel letter to the enclosure of neon transformers or power supplies shall be in accordance with Standard UL 48. Plastic Channel Letters and Face, Plastic Indoor Channel Letter Sign Body and Face 1. The channel letters have been evaluated for indoor application only. 2. The channel letters are not suitable as an electrical enclosure. 3. The channel letters are suitable for Class 2 LED and neon applications. 4. The channel letter plastic is rated 50°C. 5. Openings for conduit, electrode receptacles and mounting shall be provided in accordance with the Standard. 6. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. 7. Spacings from the channel letter to the enclosurei of neon transformers or power supplies shall be in accordance with Standard UL 48. Aluminum reinforced thermoplastic sign face trim, Type Gem Brand. 1. These trim materials are used to secure a rigid thermoplastic sign faceto an owtdoor or indoor sign. 2. The ability ofthe trim to exclude water from contacting live parts needs to be evaluated in the end product. 3. Minimum No. 8 sheet metal screws need to be provided for securing the trim to the sign body. The maximum spacing between screws shall not exceed 18 in. and no fewer than four screws are to be used per face. 4. These products do not comply with enclosure requirements. 5. The following are among the items to be considered in the end-use application. 1. Acceptable for use in wet locations. 2. Water exclusion must be determined in the end product. 3. Minimum 5 cm (2 in.) spacing from heat producing components required. 4. The specified solvents are continuously applied to edge of'acrylic or polycarbonate signface. Additional specified adhesives may be applied for the final bond. Sign Face Geheric Material _Solvent -Final Bond Adhesive _ Sign Trim Generic Materia! Methyl Methacrylate Weld-On #4 of Weld-On #16, Weld-On Cellulose Acetate Butyrate (Acrylic) (Methylene Chloride )#58 (Polycarbonate)Weld-On #4 or Weld-On #58, Lord Cellulose Acetate Butyrate Methylene Chloride Adhesive #7550 Plastic Channel Faces, Type Gemini Gemlite Channel faces and Gemini Edge Glo faces 1. The sign faces have been evaluated for indoor & outdoor applications. 2. The sign faces are not suitable as an electrital enclosure. 3. The sign face plastic is rated 50°C. 4. The sigh face for channel letter is not to be considered as providing a weatherproof enclosure, therefore all internal components shall be sujtable for outdoor use or shall be completely enclosed and protected from weathering. - 5. The neon tube or LED shall be spaced a minimum of 1/8. in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. 6. The sign face may be used with either plastic or metal channel letters. Plastic Channel Letters, Type Indoor, outdoor designated "GEMINJ FORMED SIGN BODY" for Class 2 powered LED modules strips. 1. These products are only suitable to house LED modules strips that are powered by UL Listed oF R/C Class 2 Power Supply rated max 30 VDC or max 15 VAC. 2. These iproducts are not suitable for use as electrical enclosures. APPROVED .. 0 6-ragguentg wgv#OUUN 1 A DCONMASTER I.D.____22(tz=//67 |Advertising Concepts Inc. 3725 Canal Drive,G. P -Zone_AL___.ort Collins, CO 80524 / / |. 970484 3637PLANNEER...d:grIE==:: DATE_f&1.1/_www.adconsions.com9===1 m QTRANSFERRED BY DATE- These documeals and plans have been created by and are Ihe exclusive in:ellectual p opertyol Adcon In CAny unauthodzed use, disclos,i,3. dissemination or dupli- eation of:any 01 !he intomiation con'ained hemin may result in liabllily under applicable laws. MEXU.©ARD-_@2.BL[L Custom Wall Sign Ill-li- baANNING INtSPECTION RCQUIRED: - FINAL_k-- NONE Shop Drawing for: ---1-Chipotle Mexican Grill Santa Ana College #2214-eq 202*Lo 14) _-60 27/7\1313 W 17th St ate A - -nta Ana Ca 92706RETAIN PLAN.13 FOR FUTURE REVISIONS. Sign Type:_V®ousSUBJECT TO ITEMS CHECKED AND CONDITI NS-BELOW: Date:10-21-13O INTER](1>R TI ONLY Drawn by:______MQO No EXT|ERIOR ALTERATIONS/MODIFICATIONSAccount Manager: _Rob K.U ALL :·.Al-ERIALS TO MATCH EXISTING Project Manager: 0 O SCREEI|fiNG REQURED Design/ Estimate #: 28070 File Name:Elevationsa 0 SUBVNTILANDSCAPE PLANS -CONDITION°·9*I joi¥-/Client Approval Q Signatu- lili . 111 1 119 Iii Ill *11 1 71* 99' 0 1 Er r 1R7 1 t / 1 7 EAST ELEVATION 1.OSEALE:178"=16" .12!E - CHIPORI £ AIMACeff in{ANT i •:t/!Lk):191=/!Mbe'll!:£•!*:6:R:D:i:il,MMill' eq 1 € CHIPOTLE , 1 1Custom Wall Sign- NOTE: Please'ensure en ted Une cha])ges atenoted on, INs drawir.g prior lo ielumg il b ADCON. Subsequenl 10 AbCON incorpoiaup& [h. red line changes requested on Ihis dmwing, any tdrther change: will lesull -n addiNonal bimng at Ike 818 01$86 pe, hour. U Approved U Approved As Noted U Revise And Resubmit -Pmauden-Mgr. Approval-Bate Fi@Eirliproval-Date AccouniMir:Apimvelate PiD*.Appeval-Bile R'31»NFER@%Revision Notes: -M®*D©AM:@820[Li .......................... 11. leg 14 $ *1®*OCADV @020&[6 - 1 1 9 1 1........ .... 8,18-Il-82,ae-I I '-I.I 7 12 7TN-NORTH-ELEVATION 837-SCALE:-i7673" leg .9 1 L i Vqig"usomauign i--1 [El t 11.........I1.....I 0000/VIU/:00000/1 1 I lu- ,1 -:nrng•,0,41/9,0.100-1 1 1 1,0.......11::11•.C: COCOCM!-00000001 1 1 1....Den/nl...... 0/000011/0/900/001 1 :#.......0'[009/On 0/0000||000/00/00| |1*010% -§§=1@§*§§@§11 --OPEN- ..... 011.00......1 11.' I r Seg. No. O *:22 :IX:.:2:2 1 L=ZE/ Lu---ii-yELL.-1 W.O. No. 0 / 3 1 SOUTH ELEVATION -Date: 01-22-14 Rev. No. D By: J[[_UIF-SCALE: 178"=-i'-8"Sheet No. 1.0 1 1 U U LI ADCON Advertising Concepts Inc. 3725 Canal Drive, Fort Collins, CO 80524 970 484 3637 www.adconsigns.com C 1 Thes e [ionun,nis aipl plan. have been cleated by:and are lie c Kdusive ir,!Ellectual pio pe, ot Adcon Inc.Any mau th oriled u se, 0 Is I.lofu le . disseminatio n or dupli- calion 01 any of the inlormalien conlain Ed hoicin may rasuli in liabilily under applicable laws. Shop Drawing for: Chipotle Mexican Grill Santa Ana College #2214 1313 W 17th St Ste A Santa Ana Ca 92706 + ' ' - Sign Type:Various Date:10-21-13O m U m O 0/ Drawn by: MD Account Manager:Rob K. 1 1 10 Project Manager: 0 Design/ Estimate;#:28070 File Name:Site Plan /.26/ Client Approval illil Sionalura Dae 0 CHIPOTLE [kil EX [1©ANI @20 L[L 1 1-.1 NOTE: Please ensule af red ne changes are notd on 1?,-s dia##1 ptor !0 re!·J,nirg it lo ADCON. Subsequenl ID ADCCN ina]:Fraing the Ed line changes:mque#ted on this diawing, a-,y fulther changes w I resull in'additional bming atthe Rte 01$85 Rei hour. U Approved Approved As Noted El Revise And Resubmit Pmduction Mgr. Approval Date Project Mgt. Apprdval Date Account Mgr. Approval Date P&D Mgr. Approval Date , Revision Notes: 5-2 nA,Fly'A.1 LI-lr-1-j SITE PLAN NOT TO SCALE " Seq. No. O 4 W.0. No. 0 Rev. No. A Sheet No. 1.1 Date: 11-5-13 By: MLD .JA .-1 ,+- 0'-234" 01 2'-5" fo 4 0'-25/8" 0'-3" -6 14'- 2" 11'-61/4"%97 cr Removable - _000._ 0090" alum iZ ,/000<t ,-- wl gasket 1 /8" Alum. - are Ihe exclusive intelleclual prop:flyof Adcon lnc.AnyCHIPOTLE-1 face'leyco -unaulhorized Use, elsclosilro, oissemination of dupli calion 01 any 01 ine in,o,malion contained herein may fesull in liability under applitable laws. cap LED controm Shop Drawing for: 1/8" 0 e 01-51/4 Ng[ILL *0'-75/8 r Lift Clip 3r Al ©CON Advertising Concepts Inc. 3725 Canal Drive, Fort Collins, CO 80524 970 484 3637 www.adconsigns.com These documents and plans have he:n created by and 12 W' sq. tube 115"11961 cut in top for service as reg.wl rectangular holes 3/8" Fasteners -1 access rih ENLARGEMENT DETAIL 41/ SCALE: N.T.S. 8'-87/8"003"4+ 0'-0 1/2" 1 7 FRONT ELEVATION , /'33 END VIEW /Prf>&9/ SCALE: 1/2"= 1'-0"4.9/ SCALE: Chipotle Mexican Grill Santa Ana College #2214 1313 W 17th St Ste A Santa Ana Ca 92706 Sign Type:Custom Date:10-21-13 Drawn by:MD Account Manager Rob K. Project Manager: 0 Design/ Estimate #:28070 File Name:Wall Sims l' 2-4314" -' l 11'-61* 'L- 11-6 7/8" 7'10'-81/8".090" alum. '1 X Ki wi gasket 6'-0" 1/ 4 -[E*il /IC -119*XEZIL - 4 i / r- Ends of 1/8" Alum.i , face overhang frame Power- --- ' ----- ,--- --' 1. .1 .,L supply to : 1:E =, - 1/8" Alum. return @ sign and 1 -- i i ! 1 L.... , 1 1: i finalhook,1 , corners/ends (glue 1 others typ.1 to face overhang)==r-2 up is by Channel--- ] ------*----letter u.-4] ...\ ,L 2 14" x 2 M" x 1/8" 1L_ Alum. sq. tube frame 11- /Power disconnect switch typ.7 11'x 2" x 1/8" Alum. - Power out Power out fec. tube brace Mounting holes (typ.)Raceway--Zcabinet'Sh CABINET FRAME DETAIL €2«/2:9,/ SCALE: 72"= 1'-0" Power disconnect switch - 1 y" typ.1 W' typ. f - ,£- 2'-4 3/4" (frame /2 - 1 -v rfT f I 1 8 Client Approval Signature Data NOTE: Please;ensum d fed line changes am notedion this d aing prior 13 rE im:ig,110 ADCON Subsequent to ADCON Incorpera-n,1 the redlina changes requested on IhiS dmwing. :ny furlherdinges w11 resuR in addlknal blling al te Rte of $86 per how. El Approved El Approved As Noted O Revise And Resubmit Production Mgr. Approval Date Project Mgr. Approval Date- Account Mgr. Appfoval Date P&D:Mgr. Approval Date SPECIFICATIONS FOR (3) ILLUMINATED CHANNEL LETTER SIGN ( 49.583 SQ. FT.)- -- Revision Notes CHANNEL LETTERS "CHIPOTLE", PEPPER LOGO, and "MEXICAN GRILL" LETTER TYPE= Face-Lit pan channel letters DEPTH= 3 FACES= Pepper Logo= 34" Clear acrylic w/ recessed graphics All others= 3/16" Cyro #2447 Milk-White acrylic TRIMCAP= 1" Brown Jewelite BACKS= .040" Pre-finished white aluminum RETURNS= .040" Pre-finished Adobo Brown aluminum (w/ Weep holes) ILLUMINATION= GE Tetra miniMAX white LEDs MOUNTING= "Chipotle" & Pepper= Mount to face of raceway w/ #10 Tek screws as reg. "Mexican Grill"= Mount 1/2" off fascia w/ #12 screws as reg "CHIPOTLE" & PEPPER LOGO RACEWAY CABINETS FACE= 1/8" Aluminum-Attachment to frame via Versalok adhesive Note: faces overhang ends of frame typ. RETURNS= @ ends/Corners- 1/8" Alum. spot weld and Versalok to face BACK= .040" Alum.- Rivet or screw to back of frame as reg. "CHIPOTLE" & PEPPER LOGO RACEWAY CABINETS (Continued) FRAME= 2 72" x 1/8" Aluminum sq. tube w/ 1" x 2" x 1/8" alum. brace LIFT CLIPS= W' Steel plate w/ welded 3/8" nut glued to inside of frame. Attach W steel angle lift clips to top of cab. w/3/8- bolts MOUNTING= Mount to existing fascia w/ 3/8,1 lag bolts through face/ frame (Heyco plugs required in cabinet face) ACCESS= Flush .090" alum. lid & gasket covers top of frame tube cut out ELECTRICAL PRIMARY= 120V electrical to sigh and final hook up is by others (leave 6'-0" pigtail out back of raceway cabinets in M" seal-tite conduit). , SECONDARY= "CHIPOTLE" & Pepper logo raceway cabinets= 12V LED wire leads jumped in raceway. 12V LED transformers mounted in top sq. tube of raceway "MG" Letters= 12V wire leads jumped thru remote mounted boxes w/ 12V LED transfofmers POWER DISCONNECT= Toggle switch on end of raceway cabinet and front of remote mounted power box as reg. "Mexican Grill" - Channel letters LEDs - mounted power supplies typSh END SECTION 43/ SCALE: N.T.S. COLOR SPECIFICATIONS (ED RT.M. PMS #484C "Roasted Red" (Nuance)NOTE: Paint all exposed Seq. No. O 34 fasteners and Heyco caps W.O. No. O RIM. PMS #4625C "Adobo Brown" (Nuance)to match adjacent finish /9 Date: 01-23-14 Rev. No. L By: JLL Sheet No. 2.0 - Remote e l 20- te A rfur)33-¥3§5'Fo¥-emero-'JaUal Jed SMans (V) Ulnuqu„E '-'alue) UO „t7Z U.1 n LU ! X e w8 'SMaDS lelaul 1304SOI#'UO!1elleuedJeuel jed salow ule.Ip .14 (Z) n 1 '0 if 0 0 90 r# L ROUP Ed*1 -8r TYPE CODE EDITON grk# 4 nazz'E 0'2 2 -550 AL lae 33 0 21:00 :Ck ZI,ZE .:* 322 0 v.0.8 &80 /CCS mLL 502 0 /91• B && 1.E: E =9=t.88% 8 m10 1 5 0 & m--ceo Sw w -f E€ E O Az 58 € ELECTR PLAN AP OUpede pu,9 guat 16 0 %032 R 101<205-93/ 001-1-3>307 0 3 =E =49-2 '0 2 E EEg 0 6- a. %29 CD020E -6 5 £ 2 0 - 70 JL O 0 0 0, -O 0 8--8.0 k J.-9 -¥EPCO M 73 a O 3.50.... Crm 131 € 2 -Ect FEE YES YES E