HomeMy WebLinkAbout10180962_2781 W. MACARTHUR F-2 - Plan (2)Planning & Building Agency
Building and Safety Division
20 Civic Center Plaza
P.O. Box 1988 (M-19)
Santa Ana, CA 92702
(714) 647-5800
www.santa-ana.ora
ELECTRICAL SIGN
REQUIREMENTS
'1 'Jlf r. . . '.1
Code references are to the 2010 California Electrical Code (CEC)
All signs require Planning Department approval.
All electrical signs require electric plancheck and permit.
1. Manufacturer's instructions are required at the time of submittal
C-11: 3-21-2011
2. Submit detailed installation instructions including diagrams to the Building Department
for plan review at the time of submittal. Plans must include appropriate items noted by
this bulletin.
3. Cash or surety bond in the amount of $200.00 is required at time of issuance for each
address. The cash or surety bond will be refunded after all required finals.
A building permit is also required - except for open or highlight neon lighting.
Installation Requirements:
CONTACT FIELD INSPECTOR PRIOR TO SIGN INSTALLATION.
(SEE SECTION G OF THIS BULLETIN)
1. Conductors and equipment shall comply with California Electric Code Article 600.
2. All metal parts of a sign shall be bonded in the manner specified in Article 250. Isolated
metal parts are permitted to be bonded by using an external green insulated conductor.
Equipment grounding & bonding conductors must be sized by 110.26 and protected from
physical damage. Minimum size is 14 AWG. CEC 600.7
3. A listed disconnect switch in the power supply primary, shall be installed within sight of
sign or have permanently installed means for locking in an "OFF" position. This is also
true for a transformer enclosure. CEC 600.6
4. A listed receptacle or an approved termination device shall be used for each neon
electrode. To relieve stress at terminations, tubing shall be supported with listed tube
supports in an approved manner within six inches of electrode connection.
CEC 600.41 & 600.42
5. Every electric sign of any type shall be listed by an approved testing laboratory and shall
be installed in conformance with this listing. That includes "1 of x", "2 of x" labeling for
each separate unit of a multi-unit sign. CEC 600.3
6. All "can" letters and transformers housings shall have section labels that are readily
visible after installation. CEC 600.4
7. Transformers shall be located where accessible and be securely fastened in place.
Page 1 of 2
When not inside the sign, they need a 3 foot high x 3 foot wide x 3 foot deep workspace.
Transformers are permitted to be located in attics or canopies provided there is a
passageway at least 3 feet high x 2 feet wide with a minimum 12 inch catwalk/walkway
from the point of entry. Transformers must be securely fastened and independent of T-
bar when above a suspended ceiling. No part of siqn mav be fed with flexible cord when
located above T-bar ceilings. CEC 600.21(E&F) & 400.8
8. Adequate illumination shall be provided for all working spaces about electrical
equipment. This applies to attics and canopies when entry is required to service or
inspect the equipment. At least one switch is required at entrance. CEC 110.34 & 600.21
9. Doorway to an attic or canopy space shall be minimum 3 feet by 2 feet wide.
CEC 600.21(E)
E. Open neon outline or highlight lighting.
1. To be treated as a sign by this department. However, Section D-5 & D-6 of this bulletin
will not apply.
2. Neon tubing shall be located where not normally exposed to physical damage. Open
neon tubing below,9 feet shall be protected from physical damage by an approved
shielding method. CEC 600.30 and 1 10.34(E)
F. Light-Emitting Diode (LED) Signs
1. Will be treated as a sign by this department. All sign rules in sections A, B, C, D, F, and
G will apply as appropriate.
2. LEDillumination for signage must be a listed or recognized component. Many LED
manufacturers specify particular brands and models of transformers some do not.
Manufacturer information to clarify this issue is required on LED sign plans.
3. Unlisted LEDs may not be used in an electrical sign or as permanently installed
illumination. 110.3
4. Please have packaging or catalog cut-sheets on hand for inspector to review when LED
modules do not bear listing symbols.
G. Inspections
1. Contact an Electrical Inspector one (1) workday (minimum) in advance of installation to
arrange a site meeting on dav of installation.
2. Call for inspection Monday through Friday, 8:00- 8:30 a.m. at (714) 647-5821. Approved
prints and the job card must be on site for inspection.
Page 2 of 2
October 1, 2013 SIGN COMPONENTS MANUAL (SAM) 76
7. A temperature test is not required if the LED drivers are spaced at least 1 in. apart end to end or 4 in. apart in other directions.
Spacng to plastic shall be 1 inch minimum and to metal may be zero in. The need for a temperature test shall be considered if
the LED driver is mounted closer than the referenced spacings. For reference these LED drivers have been tested in a 50 C
ambient and maximum case temperature is 73C.
JKL COMPONENTS CORP E339601
13343 PAXTON ST
PACOIMA, CA 91331
Class 2 LED Modules, designated as ZAF-336-24, ZAF-486-24, ZAF-636-24, ZAF-936-24, ZAF-1236-24, may be followed by
additional suffixes for color temperature.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 24V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means
LED Illumination Modules, ZM-4047-CW, ZM-1957-CW, ZM-1543-R.
1. Each Class 2 LED Modules is only suitable for connection to a Class 2 power source, max. 24 Volt dc or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limits.
3. Class 2 LED modules, rated max. 12 Watts per LED unit or less. When units are connected to a Class 2 circuit, they are not
to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 24 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Modules, Cat. No. ZWF-XXXX-XX, where XXXX-XX will be replaced with alpha-numeric digits that indicated
length and color.
1. These Class 2 LED modules are only suitable for connection to a Class 2 power source, rated 15 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limits.
3. These Class 2 LED modules are rated max. 2 Watts.per LED module. When these units are connected to a Class 2 circuit,
they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 15 Volts or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Modules, Cat. No. ZWF-337-24CW, ZWF-438-24CW, ZWF-638-24CW, ZWF-939-24CW, ZWF-1239-24CW,
ZWF-337-24WW, ZWF-438-24WW, ZWF-638-24VWV, ZWF-939-24VWV, ZWF-1239-24WW
1. Each Class 2 LED Module is only suitable for connection to a Class 2 power source, max. 24 Volt dc or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limits.
3. Class 2 LED modules rated max. 12 Watts per LED unit or less. When units are connected to a Class 2 circuit, they are not
to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 24 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
JOHNSON WALKER & ASSOCIATES L LC, DBA IMPERIAL PLASTICS MFG E225580
4337 MILL ST
NORTH BRANCH, MI 48461
Aluminum Reinforced Sign Face Trim, designated Signatrim.
1. Acceptable for use in dry, damp and wet locations.
2. Water exclusion must be determined in the end product.
3. Minimum 5 cm (2 in.) spacing from heat producing components required.
4. The specified solvents are continuously applied to edge of acrylic or polycarbonate sign face. Additional specified adhesives
may be applied for the final bond.
Sign Face Generic Material Solvent Final Bond Adhesive Sign Trim Generic Material
Methyl Methacrylate (Acrylic)Methylene Chloride Methylene Chloride Cellulose Acetate Butyrate
Methyl Methacrylate (Acrylic)Weld-ON #4 Weld-ON # 16 Cellulose Acetate Butyrate
Methylene Chloride
Polycarbonate Transco Transco Cellulose Acetate Butyrate
Channel Bond Channel Bond
5. The suitability of the securement or "fit" of this trip cap shall be determined in the end product. Screws or solvents are
considered acceptable for permanent mounting.
v JS LED TECHNOLOGY CORP, DBA JS LED POWER INC E308859
1318 MAINE AVE
BALDWIN PARK, CA 91706
Class 2 LED Modules, Cat. No. JE-OOABCD-XY-EZ Series, where A, B, C, D, E, Z, X and Y may be any alphanumeric characters,
or suffixes may be blank.
77 SIGN COMPONENTS MANUAL (SAM)October 1, 2013
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt AC/DC or less.
2. These products are each rated max. 24 watts per module. When units are connected to a Class 2 circuit, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 Power Supply, Cat. Nos. MJ-ABCD-WXYZ Series, where AB is 12, and CD-WXYZ is 20-1670,40-3300 or 60-5000.
1. These power supplies have a maximum of one Class 2 outputs. The output of these power supplies have been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations only.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to
sidewalls, and minimum 2 inches spacing to top of enclosure.
4. These products have not been subjected to Leakage Current, Strain Relief, and Impact Tests. The need to conduct these tests
shall be considered in the product. In addition to these tests, the need to conduct the Mold Stress test on model MJ-1260-500
shall be considered in the end product.
5. These products shall be provided with additional enclosure when used in the end product.
Class 2 LEDs, Cat. Nos. Cat. Nos. JE-001X (HS-F504BR4TN), JE-002X (HS-F504BN4TN), JE-003X (HS-F504884TN), JE-0041
JE-005X (HS-F504BY4TN), JE-006X (HS-R483AR4CY or HS-R484CN4CY or HS-R484CB4CY), where X may be replaced with A,
B, G, M, R or W.
1 These products are only suitable for connection to a Class 2 power source, rated 15 Volt (DC or AC) or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Controllers, Models HM-12RGB5A3-RC, HM-12RGB5A3-XY Series, where suffix X and Y may be any alphanumeric
characters or blank for marketing purpose only.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated max 24VDC.
2. These products are rated per the Table below. When units are connected to a Class 2 circuit, their ratings are to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
{Model Input - Class 2 Output - Class 2
] HM-12RGB5A3-XY Series 12- 24 Vdc 10-24V 24 W
3. These products are suitable for use in dry, and damp.
4. These products are each rated max. 24 watts. When units are connected to a Class 2 circuit, they are not to draw a total
wattage of greater than the secondary or output rating of the Class 2 supply.
Sign accessories, Class 2 LED power supplies, Model MJ-12100.
1. The output of this component complies with Class 2 requirements in the Standard for Class 2 Power Units, UL 1310.
2. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
3, These products shall be enclosed in the end product.
4. These power supplies are suitable for use in dry and damp locations.
5. These devices are intended for factory installation only.
6. This Class 2 power supply is not provided with any grounding. The enclosure must be grounded in the end product.
JUSTIN INC E235322
2663 N LEE AVE
SOUTH EL MONTE, CA 91733
Class 2 Power Supply, Model 601-12DC, 601-12DCR, 101-24DCR, 02240-12DCR, C2240-24DCR, C2240-12, 62240-12-240,
C2240-24, and C2240-24-240.
1. These power supplies have been evaluated for use in LED signs.
2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
3. These units are suitable for use in dry and damp locations without a need for an additional enclosure.
4. The output of this power source shall not be connected to any other power source or provide power to components connected
to another power source.
5. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at
least 150 mm (6 in) inside.
Class 2 Power Supply, Model 601-12DC-LC, 601-12DCR-LC, 101-24DCR-LC, C2240-12DCR-LC, C2240-24DCR-LC, C2240-12-
LC, C2240-12-240-LC, C2240-24-LC, and C2240-24-240-LC.
1. These power supplies have been evaluated for use in portable LED signs.
2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
3. These units are suitable for use in dry and damp locations without a need for an additional enclosure.
4. The output of this power source shall not be connected to any other power source or provide power to components connected
to another power source.
5. The attachment plug on the end of the power supply cord is not to be removed.
KASON INDUSTRIES INC
57 AMLAJACK BLVD
NEWNAN, GA 30265
Power supplies with Class 2 output circuits, Model 61815000200.
E363080
LED MODULE SERIES
ITEM NO.:LS0783
LS0783H-3
4 / e
SIZE:
• All the size date above is in mm
• Tolerance for the size date is 1 0.2mm
APPLICATION:
• Applicable forhome, shopping mall, office
meeting room, hotel, cabinet, and show
windows, etc.
C€
E 15.8mm
53.8mm
Ih
111-1 7.4mn
Sheet No. : 01
091.u: E320022
LS0783H-4
## ¥ 1
./
4..
FEATURE:
• No UV or IR radiation.
• Superthinand flexible
• Waterproof IP65
• High Brightness SMD LED
• LED QTY: LS0783H-3: 3PCS
LS0783H-4:4PCS
• 50000 hours long life span
• Color Temperature
CW: 8000-900OK
DW: 6000-6500K
WW: 3000-3300K
I Low temperature rising, less than 20t
. Less than 7% light decay in 6,000 hours testing
0 120° Beaming Angle
• Colour: LS0783H-3: G/B/P/WW/DW/CW
LS0783H-4: R/Y
Absolute Maximum Rating at TA=25t
Parameter Symbol Absolute Maximum Rating Unit
Voltage VIN DC12V VAC
Electrostatic Discharge ESD 2000 V
Operating Temperature TOPR -20°045°C °C
Storage Temperature TSTG -20°C-60t °C
Sheet No.:02
Electrical/Optical Characteristics at TA=25t(VIN=DC12VAC, 50Hz)
Colour Voltage Current Power CT/WL Lumin.ous Ra
WW DC12V 20mA 0.6W 3000-3300K ------ 64
CW DC12V 20mA 0.6W 8000-9000K ------ 83
R DC12V 20mA 0.6W 620-630nm ------ ------
G DC12V 20mA 0.6W 520-525nm ------ ------
P DC12V 20mA 0.6W 380-760nm ------ ------
Y DC12V 20mA 0.6W 585-595nm ------ ------
Maximum
'Connection
100Pcs
100Pcs
100Pcs
100Pcs
100Pcs
100Pcs
illuminated diagram
90°
9oooo., 80%6096 4096 20%0%2096 4096 8096 too·:6
INSTALLATION
50%
1.Please rip PE adhesive tape on the back of the
product, then stick to the oblects where you want.
2.Use the screws to fasten it again.
MAX 100PCS
Power .F EDC12V -1-
0
3.Connect multiple product (max 100 pcs), (The tatal power consumption of products should be less than 80% of
driver's power),the connect the driver.
• Connect red wire to the positive polarity and black wire to the negative polarity of power supply
• Operate on 12 Volt DC Power Supply(constant voltage)
• Wire length of powersupplyshould be no more than 3 meters;if more than that,suggest increasing wirediameter
Sheet No. : 03
NOTE
• Low voltage product, please make sure of the DC12v +2V input voltage
• Please don't press the elements on the PCB from any angle by stress
• Non-bendable
• Please don't install in flammable, explosive orcorrosive circumstances
-1)iscount'
= ' C
4.4-•------------¥ u ¢4/»7Vile/11.4·5111'14'11:1-9%7"V
m1 GO
115 151kth-*m THAU"4;3:- L 'FIRK' 19%\TilR'.V[: 34'nrmfl MASSAGE"
L
14861 Moran St. #B Westmister, CA 92683
(714)848-9616 Phone (714)740-5030 Fax
Website: www.i2isigns.com
Email: info@i2isigns.com
COMMENTS:
i . - r---[-1
CLIENT:Nuad Thai Massage
ADDRESS 2781 W McArthur Blvd. Suite F2
LOCATION:Width 22'
DATE:02/5/14 CONCEPT:A1234 SALES:
MASTER I.D. ZO/4-//3590
G.P 50 Zone 09--
11
PI ANNFR 14
TRANSFEF P - TE
RR #0 1,1@iZgfQjy gHggETo BE
)UGH FINAL NONE X
..:.PPROVED
Orr
CUSTOMER APPROVAL LAN[U#19 AP<ROW
ED?&MTURE TEDASIGNATURE DA
This sign is intended to be
installed in accordance with
the requirements of Article
600 of the National Electrical
Code and/or other applicable
local codes. This includes
proper grounding and
bondingofthe sign.
Contractors Lic.
#917099
SCALE: 1/8" = 1'
NOTE: This is an original
drawing, created by i2i Signs
Corp. It is submitted for your
personal use in connection
with a project being planned
foryou by i2i Signs. It is not
PAGE to be show to anyone outside
1 your organization, nor is it to
be used, reproduced, copied orOF
exhibited in any fashion. Any
2 printed colors on drawing are
approximate.
---Discount«
THA| 14
14861 Moran St. #B Westmister, CA 92683
(714)848-9616 Phone (714)740-5030 Fax
30"Website: www.i2isigns.comy 1[[!IlgI MASSAG E14 Email: info@i2isigns.com
COMMENTS:
14'
1. MANUFACTURE AND INSTALL ONE SET OF ILLUMINATED CHANNEL LETTERS
2. FACES:
- COLOR "Nuad" 12"H 1/8 ACRYLIC WHITE W/ RED OUTLINE 70+732-9
- COLOR THAI MASSAGE" 14"H 1 /8 ACRYLIC RED y27 9.3
3. RETURN:
-5"DEEP PAINTED BLACK- TRIMP CAP BRONZE
4. ILLUMINATION: WHITE 12 DC LED LIGHT UITS - SPACING: 2.5 UNITS/STROKE INCH
5. LETTERS SHALL BE MOUNTED DIRECTLY ON THE WALL 5'x22' WITH €1
NON-FERROUS FASTENERS 1/4"x 1-1/2"PER LETTER (4) MIN.--1-
6. ALL WIRING AND COMPONENTS TO BE UL APPROVED.42\7. TRANSFORMER TO BE UL LISTED mAM600 WATT AS NEEDED4)DISCON·NECT_SWITCH: - --O
8. ULLISTED 18AWGWIRE RETAIN PLANS FOR FUTURE REVISIONS.
9. EXISTING WALL 5'H x 22'W SUBJECT TO ITEMS CHECKED AND CONDITIONS
BELOW:
CLIENT:Nuad Thai Massage
ADDRESS 2781 W. McArthur Blvd. Suite F2
LOCATION:Width 22' -
DATE:02/5/14 CONCEPT:Al 234 SALES: RR
O INTERIOR TI ONLY -(4K
O NO EXTERIOR ALTERATIONS/MODIFICATIONS
O ALL MATERIALS TO MATCH EXISTING
O SCREENING REQUIRED
O SUBMIT LANDSCAPE PLANS -(t«
#*u Wait, 9#J.Water drain hole
L vivul I B. ; USTOMER APPROVAL LANOLORD APPHOVAL
0**™44 316/1,4
SIGIWFURE JDATE SIGNATURE DATE
DRAWN BY:RR WE HAVE REVIEWED AND APPROVED THE SIGN DETAILED HEREIN TO BE
FABRICATED PER THE SPECIFICATIONS SHOWN ON THE DRAWING
37--
This sign is intended to be
installed In accordance with
the requirements of Article
600 of the National Elect,ical
Code and/0, other applicable
local codes. This includ es
proper grounding and
bonding of the sign.
Contractors Lic.
#917099
SCALE: 1/8"=1'
NOTE: This is an original
drawing, created by i2i Signs
Corp. It is submitted for your
personal use in connection
with a project being planned
for you by i2i Signs. It is not
PAGE to be show to anyone outside
2 your organization, nor is it to
be used, reproduced, copied orOF
exhibited in any fashion. Any
2 printed colors on drawing are
approximate.
-
W
9 1// 1 Li
l
.ARP-fUR-93«--1-h
City of Santa Ana. -CBC- 4-CE_2-013Minimum (4) screws per letter,maximum 24" on center, 2" penetration, #10 sheet metal screws, &(2) 44" drain holes per letterV•
ect for the
-V
,looeS er**<19 n06 06.4,0.0019,A
CPI
olsen\»
?\"f3
PERMIT TYPE:CNREE>LBG
MECH ?RADING
PERMIT#lojec)949/ELECTRICAL j OCC. GROUP 620 63«9PLAN APPROVAL t -CONSTA. TYPFThis set of plans and speclfications must be kipt on
CODE EDITION 520,3 the job at all times And It Is unlawful to make anyI changes or alterations on same without written per-FLOOD ZONE . 9f mission from the Department of Building Safety /City of Santa Ana. .
The approval of this: plan andepAclflcatiorts SHALL FLOOD ZONE CERTIR REQ'D YES 40NOT ba. beld to permit nor.be'an approval of thoviolation or any provisions of ANY City Ordinance MICROFILM YES lk>or State Law.
-'- I'll'812%) )51 RADIANT BARRIER @ ROOF YES NO
. 11
RESIDENTIAL DEV. FEE YES 26
Approved
CITY OF SANTA ANA
DEPARTMENT OF BUILDING SAFETY SCHOOL DISTRICT YES (,60
r
0 ...-9
.f position.
or above
& passage
00.41 4 en
j
r'.
:
¢f 9 1