The URL can be used to link to this page

Home My WebLink About1316 3%4 E Warner Ave Unit# WCC01 - Plan304-C3 SHEET #:REVISION: SHEET TITLE: REV. 0 1 DATE 03/06/25 04/10/25 DESCRIPTION ISSUED FOR CONSTRUCTION ISSUED FOR CONSTRUCTION REVISIONS APPROVED BY: CHECKED BY: DRAWN BY: CW MEW FIN PROJECT INFORMATION: IE84820A 1316 3/4 E WARNER AVENUE, UNIT #WCC01 SANTA ANA, CA 92705 THE INFORMATION CONTAINED IN THIS SET OF DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO THE CLIENT IS STRICTLY PROHIBITED. 1200 CONCORD AVENUE CONCORD, CA 94520 PREPARED FOR: RMobileT 2 06/20/25 ADDRESS JDX COMMENTS 3 03/25/26 ADDRESS JDX COMMENTS A&E FIRM: 1355 WINDWARD CONCOURSE, SUITE 410 ALPHARETTA, GA 30005 TEL: 678-990-2338 EXISTING EQUIPMENT PLAN SCALE: 3/8" = 1'-0" NOTE: THE POWER DESIGN FOR ANY AC ELECTRICAL POWER CHANGES IS TO BE PERFORMED BY OTHERS AND IS SHOWN HERE FOR REFERENCE PURPOSES ONLY. T-MOBILE IS SOLELY RESPONSIBLE FOR THE ELECTRICAL POWER DESIGN. NOTES: ·REMOVE THE (12) EXISTING VALVE-REGULATED LEAD-ACID BATTERIES IN THE EXISTING B160 BATTERY CABINET. ·INSTALL (8) NEW ERICSSON 6618 LITHIUM-ION BATTERIES IN THE EXISTING B160 BATTERY CABINET. NEW EQUIPMENT PLAN SCALE: 3/8" = 1'-0" (E) T-MOBILE GPS ANTENNA (E) T-MOBILE EQUIPMENT (E) T-MOBILE 2'-6"X17'-6" RAISED CONCRETE PAD (E) T-MOBILE 21'-7"X9'-0" CONCRETE PAD (E) T-MOBILE 6160 EQUIPMENT CABINET (E) T-MOBILE B160 BATTERY CABINET (E) MONOPOLE (E) FOUNDATION PAD NORTH (E) T-MOBILE CIENA (TYP) (E) T-MOBILE ICE BRIDGE (E) T-MOBILE CONCRETE PAD (E) T-MOBILE PPC CABINET (E) T-MOBILE UTILITY METER (E) T-MOBILE VALVE-REGULATED LEAD-ACID (VRLA) BATTERIES TO BE REPLACED (E) T-MOBILE EQUIPMENT CABINET (E) T-MOBILE FTP CABINET (E) T-MOBILE TELCO CABINET (E) T-MOBILE UTILITY H-FRAME (TYP) (E) TOWER COMPOUND W/ CHAIN-LINK FENCE 10' SETBACK FROM BATTERY CABINET (P) ERICSSON 6618 LITHIUM-ION BATTERIES (8 TOTAL) EXISTING & NEW EQUIPMENT PLANS NORTH 21 ' - 7 " 32 ' - 0 " 9'-0" 2'-6" 17 ' - 6 " (E) VAULT (E) T-MOBILE GPS ANTENNA (E) T-MOBILE EQUIPMENT (E) T-MOBILE 2'-6"X17'-6" RAISED CONCRETE PAD (E) T-MOBILE 21'-7"X9'-0" CONCRETE PAD (E) T-MOBILE 6160 EQUIPMENT CABINET (E) T-MOBILE B160 BATTERY CABINET (E) MONOPOLE (E) FOUNDATION PAD (E) T-MOBILE CIENA (TYP) (E) T-MOBILE ICE BRIDGE (E) T-MOBILE CONCRETE PAD (E) T-MOBILE PPC CABINET (E) T-MOBILE UTILITY METER (E) T-MOBILE EQUIPMENT CABINET (E) T-MOBILE FTP CABINET (E) T-MOBILE TELCO CABINET (E) T-MOBILE UTILITY H-FRAME (TYP) (E) TOWER COMPOUND W/ CHAIN-LINK FENCE 10' SETBACK FROM BATTERY CABINET 21 ' - 7 " 32 ' - 0 " 9'-0" 6'-0" 13'-8" 2'-6" 17 ' - 6 " (E) VAULT (E) ACCESS GATE (E) ACCESS GATE 6'-0" 13'-8" NOTE: ESS DISCONNECTS ARE INTERNAL TO THE CABINET. GC TO ENSURE PLACARDS OR DIRECTORIES SHALL BE INSTALLED AT THE LOCATION OF THE MAIN ELECTRICAL SERVICE DISCONNECTING MEANS, INDICATING LOCATION OF STATIONARY BATTERY SYSTEM DISCONNECTING MEANS IN ACCORDANCE WITH CALIFORNIA ELECTRICAL CODE 2025 CFC 1027.4. NOTE: GC TO PLACE NFPA 704 PLACARDS AS APPLICABLE PER CFC STANDARDS. 03/25/26 s<s<.J-b.J-b,,.a=,,.a=-------- 304-C4 SHEET #:REVISION: SHEET TITLE: REV. 0 1 DATE 03/06/25 04/10/25 DESCRIPTION ISSUED FOR CONSTRUCTION ISSUED FOR CONSTRUCTION REVISIONS APPROVED BY: CHECKED BY: DRAWN BY: CW MEW FIN PROJECT INFORMATION: IE84820A 1316 3/4 E WARNER AVENUE, UNIT #WCC01 SANTA ANA, CA 92705 THE INFORMATION CONTAINED IN THIS SET OF DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO THE CLIENT IS STRICTLY PROHIBITED. 1200 CONCORD AVENUE CONCORD, CA 94520 PREPARED FOR: RMobileT 2 06/20/25 ADDRESS JDX COMMENTS 3 03/25/26 ADDRESS JDX COMMENTS A&E FIRM: 1355 WINDWARD CONCOURSE, SUITE 410 ALPHARETTA, GA 30005 TEL: 678-990-2338 BATTERY SPECS NOTES: 1.BATTERY TERMINALS - ELECTRICAL CONNECTION BETWEEN CELLS ON SEPARATE LEVELS OR RACKS SHALL NOT PUT MECHANICAL STRAIN ON THE BATTERY TERMINALS. 2.VENTS - EACH VENT CELL SHALL BE EQUIPPED WITH A FLAME ARRESTOR. 3.SEALED CELLS - WHERE A BATTERY IS CONSTRUCTED SUCH THAT EXCESSIVE ACCUMULATION OF PRESSURE COULD OCCUR WITHIN THE CELL DURING OPERATION, A PRESSURE RELIEF VENT SHALL BE PROVIDED. 4.VENTILATION - PROVISION APPROPRIATE TO THE BATTERY'S TECHNOLOGY SHALL BE MADE FOR SUFFICIENT DIFFUSION AND VENTILATION AND GASSES FROM THE BATTERY, IF PRESENT, TO PREVENT THE ACCUMULATION OF AN EXPLOSIVE MIXTURE. 03/25/26 s<s<.J-b.J-b,,.a=,,.a=-------- 304-C5 SHEET #:REVISION: SHEET TITLE: REV. 0 1 DATE 03/06/25 04/10/25 DESCRIPTION ISSUED FOR CONSTRUCTION ISSUED FOR CONSTRUCTION REVISIONS APPROVED BY: CHECKED BY: DRAWN BY: CW MEW FIN PROJECT INFORMATION: IE84820A 1316 3/4 E WARNER AVENUE, UNIT #WCC01 SANTA ANA, CA 92705 THE INFORMATION CONTAINED IN THIS SET OF DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO THE CLIENT IS STRICTLY PROHIBITED. 1200 CONCORD AVENUE CONCORD, CA 94520 PREPARED FOR: RMobileT 2 06/20/25 ADDRESS JDX COMMENTS 3 03/25/26 ADDRESS JDX COMMENTS A&E FIRM: 1355 WINDWARD CONCOURSE, SUITE 410 ALPHARETTA, GA 30005 TEL: 678-990-2338 ESS DETAILS NOTES: THE B160 IS COMPATIBLE WITH 6618 AND 6624 LITHIUM-ION BATTERIES. NO MODIFICATION TO THE CABINET REQUIRED. PARTS REQUIRED ARE EXISTING IN THE CABINET ON SITE. 03/25/26 s<s<.J-b.J-b,,.a=,,.a=-------- 304-C6 SHEET #:REVISION: SHEET TITLE: REV. 0 1 DATE 03/06/25 04/10/25 DESCRIPTION ISSUED FOR CONSTRUCTION ISSUED FOR CONSTRUCTION REVISIONS APPROVED BY: CHECKED BY: DRAWN BY: CW MEW FIN PROJECT INFORMATION: IE84820A 1316 3/4 E WARNER AVENUE, UNIT #WCC01 SANTA ANA, CA 92705 THE INFORMATION CONTAINED IN THIS SET OF DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO THE CLIENT IS STRICTLY PROHIBITED. 1200 CONCORD AVENUE CONCORD, CA 94520 PREPARED FOR: RMobileT 2 06/20/25 ADDRESS JDX COMMENTS 3 03/25/26 ADDRESS JDX COMMENTS A&E FIRM: 1355 WINDWARD CONCOURSE, SUITE 410 ALPHARETTA, GA 30005 TEL: 678-990-2338 ESS DETAILS 03/25/26 s<s<.J-b.J-b,,.a=,,.a=-------- 304-C7 SHEET #:REVISION: SHEET TITLE: REV. 0 1 DATE 03/06/25 04/10/25 DESCRIPTION ISSUED FOR CONSTRUCTION ISSUED FOR CONSTRUCTION REVISIONS APPROVED BY: CHECKED BY: DRAWN BY: CW MEW FIN PROJECT INFORMATION: IE84820A 1316 3/4 E WARNER AVENUE, UNIT #WCC01 SANTA ANA, CA 92705 THE INFORMATION CONTAINED IN THIS SET OF DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO THE CLIENT IS STRICTLY PROHIBITED. 1200 CONCORD AVENUE CONCORD, CA 94520 PREPARED FOR: RMobileT 2 06/20/25 ADDRESS JDX COMMENTS 3 03/25/26 ADDRESS JDX COMMENTS A&E FIRM: 1355 WINDWARD CONCOURSE, SUITE 410 ALPHARETTA, GA 30005 TEL: 678-990-2338 ESS DETAILS 03/25/26 s<s<.J-b.J-b,,.a=,,.a=-------- 304-C8 SHEET #:REVISION: SHEET TITLE: REV. 0 1 DATE 03/06/25 04/10/25 DESCRIPTION ISSUED FOR CONSTRUCTION ISSUED FOR CONSTRUCTION REVISIONS APPROVED BY: CHECKED BY: DRAWN BY: CW MEW FIN PROJECT INFORMATION: IE84820A 1316 3/4 E WARNER AVENUE, UNIT #WCC01 SANTA ANA, CA 92705 THE INFORMATION CONTAINED IN THIS SET OF DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO THE CLIENT IS STRICTLY PROHIBITED. 1200 CONCORD AVENUE CONCORD, CA 94520 PREPARED FOR: RMobileT 2 06/20/25 ADDRESS JDX COMMENTS 3 03/25/26 ADDRESS JDX COMMENTS A&E FIRM: 1355 WINDWARD CONCOURSE, SUITE 410 ALPHARETTA, GA 30005 TEL: 678-990-2338 ESS DETAILS 03/25/26 s<s<.J-b.J-b,,.a=,,.a=-------- 304-C9 SHEET #:REVISION: SHEET TITLE: REV. 0 1 DATE 03/06/25 04/10/25 DESCRIPTION ISSUED FOR CONSTRUCTION ISSUED FOR CONSTRUCTION REVISIONS APPROVED BY: CHECKED BY: DRAWN BY: CW MEW FIN PROJECT INFORMATION: IE84820A 1316 3/4 E WARNER AVENUE, UNIT #WCC01 SANTA ANA, CA 92705 THE INFORMATION CONTAINED IN THIS SET OF DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO THE CLIENT IS STRICTLY PROHIBITED. 1200 CONCORD AVENUE CONCORD, CA 94520 PREPARED FOR: RMobileT 2 06/20/25 ADDRESS JDX COMMENTS 3 03/25/26 ADDRESS JDX COMMENTS A&E FIRM: 1355 WINDWARD CONCOURSE, SUITE 410 ALPHARETTA, GA 30005 TEL: 678-990-2338 ESS DETAILS 03/25/26 s<s<.J-b.J-b,,.a=,,.a=-------- 305-E1 SHEET #:REVISION: SHEET TITLE: REV. 0 1 DATE 03/06/25 04/10/25 DESCRIPTION ISSUED FOR CONSTRUCTION ISSUED FOR CONSTRUCTION REVISIONS APPROVED BY: CHECKED BY: DRAWN BY: CW MEW FIN PROJECT INFORMATION: IE84820A 1316 3/4 E WARNER AVENUE, UNIT #WCC01 SANTA ANA, CA 92705 THE INFORMATION CONTAINED IN THIS SET OF DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO THE CLIENT IS STRICTLY PROHIBITED. 1200 CONCORD AVENUE CONCORD, CA 94520 PREPARED FOR: RMobileT 2 06/20/25 ADDRESS JDX COMMENTS 3 03/25/26 ADDRESS JDX COMMENTS A&E FIRM: 1355 WINDWARD CONCOURSE, SUITE 410 ALPHARETTA, GA 30005 TEL: 678-990-2338 PANEL SCHEDULE NOT TO SCALE ONE-LINE DIAGRAM NOT TO SCALE PANEL SCHEDULE & ONE-LINE DIAGRAM PANEL SCHEDULE, TABLE 1207.1.3 & BATTERY CALCULATIONS NOT TO SCALE ESS IS LOCATED OUTDOORS ON AN EQUIPMENT PAD. ESS IS NOT LOCATED IN A HABITABLE AREA. NOTES ·DISCONNECTS (CBS) INSIDE THE B160 CABINET PER INDIVIDUAL BATTERY STRING - ALL ARE EXISTING AND TO BE RE-USED. ·ESS IS DC, NOT AC, THEREFORE IT SHOULD NOT BE INCLUDED IN THE MAINS LOAD CALCULATION. ESS/B160 IS CHARGED BY THE 6160 ALREADY IN THE LOAD TABLE. OVERVIEW OF BMS OPERATION IN BATTERY ENERGY STORAGE SYSTEMS, ONE OF THE MOST IMPORTANT HAZARD BARRIERS HELPING TO ENSURE SAFETY IS THE BATTERY MANAGEMENT SYSTEM (BMS). THE BMS PROVIDES PRIMARY THERMAL RUNAWAY PROTECTION BY ENSURING THAT THE BATTERY SYSTEM OPERATES WITHIN A SAFE RANGE OF PARAMETERS SUCH AS ITS STATE OF CHARGE AND TEMPERATURE. IN A UL 9540 LISTED BATTERY ENERGY STORAGE SYSTEM, THE BMS MONITORS, CONTROLS AND OPTIMIZES THE PERFORMANCE OF BATTERY MODULES AND DISCONNECTS THEM FROM THE SYSTEM IN THE EVENT OF ABNORMAL CONDITIONS. THE BMS ALSO PROVIDES CHARGE AND DISCHARGE MANAGEMENT OF THE BATTERIES. IN CASE OF UNDERVOLTAGE OR OVERVOLTAGE, OVER-TEMPERATURE, OR OVERCURRENT CONDITIONS, THE BMS WILL ALARM AND THEN LIMIT THE CHARGE AND DISCHARGE CURRENT OR POWER. UNDER EMERGENCY CONDITIONS, THE BMS WILL CEASE OPERATIONS AND ELECTRICALLY DISCONNECT THE BATTERY. ONE-LINE DIAGRAM NOT TO SCALE BATTERY CABINET IS LOCATED ON AN OUTDOOR PAD AND IS IN COMPLIANCE WITH CEC 706.1(6) LABELING EXAMPLE ON ESS INTERNAL DISCONNECT IN ESS DC ONE-LINE DIAGRAM ELECTRICAL NOTES: 1. ALL NEW CONDUCTORS TO BE INSTALLED SHALL BE COPPER. ALL CONDUCTORS SHALL BE THHW, THWN, THWN-2, XHHW, OR XHHW-2 UNLESS NOTED OTHERWISE. 2. CONTRACTOR IS TO FIELD VERIFY ALL EXISTING ITEMS SHOWN ON THE ELECTRICAL ONE-LINE DIAGRAM AND NOTIFY THE ENGINEER OF ANY DISCREPANCIES. 3. ALL GROUNDING AND BONDING PER THE CEG. 4. THE POWER DESIGN FOR ANY ELECTRICAL POWER CHANGE IS TO BE PERFORMED BY T-MOBILE AND IS SHOWN HERE FOR REFERENCE PURPOSES ONLY. T-MOBILE IS SOLELY RESPONSIBLE FOR THE ELECTRICAL; POWER DESIGN SOW. 5. THE E6160AC SUPPORTS AN EXTERNAL BATTERY CABINET TO SUPPLY BACKUP DC POWER DURING AN AC MAINS OUTAGE TO THE RECTIFIERS. THE BATTERY CABLE TERMINALS AND BREAKERS ARE LOCATED AS SHOWN IN FIGURE 4. EACH BREAKER IS RATED AT 300A. FOR COPPER WIRES THAT SUPPORT THIS MUCH CURRENT, IT MUST HAVE A DIAMETER OF AT LEAST 11.684 MM. IT IS BEST TO LOCATE THE TWO CABINETS ADJACENT TO EACH OTHER TO MINIMIZE CABLE LENGTH. NOTE: THE SECOND 300A BREAKER CONNECTION BETWEEN E6160AC AND B160 SHOULD BE INSTALLED. THIS IS TO PREVENT BATTERY BREAKERS FROM TRIPPING DURING A COLD START SCENARIO WHERE INITIAL CURRENT DRAW MAY TRIP THE BATTERY BREAKER AND REQUIRE FIELD VISIT TO RESET BREAKER. (E) 6160 RADIO CABINET (E) 2P 100A (E) 120/240, DISTRIBUTION PANEL (E) 2P 60A (E) 1P 20A (E) 1P 20A (E) 1P 15A (E) 120/240, 1Ø, 3W, 200A (E) PPC CABINET NEAR EQUIPMENT AREA (E) CONDUIT/ CONDUCTORS (E) SMARTMETER (E) (E) M (E) 200A, 240V POWER SOURCE (E) CONDUIT/ CONDUCTORS SU R G E P R O T E C T O R TE L C O F A N LI G H T GF I (E) 1-1/2" CONDUIT (2#1 + 1#2 GND) FOR 6160 (E) B160 BATTERY CABINET (SEE DC ONE-LINE ABOVE FOR OCP DETAILS) (E) 1P 20A ***NEW BATTERIES ARE TO BE INSTALLED IN THE EXISTING BATTERY CABINET. EXISTING CABINET IS NOT BEING REMOVED FOR THIS SCOPE.*** (E) EQUIPMENT CABINET 03/25/26 s<s<.J-b.J-b,,.a=,,.a=-------- 305-G1 SHEET #:REVISION: SHEET TITLE: REV. 0 1 DATE 03/06/25 04/10/25 DESCRIPTION ISSUED FOR CONSTRUCTION ISSUED FOR CONSTRUCTION REVISIONS APPROVED BY: CHECKED BY: DRAWN BY: CW MEW FIN PROJECT INFORMATION: IE84820A 1316 3/4 E WARNER AVENUE, UNIT #WCC01 SANTA ANA, CA 92705 THE INFORMATION CONTAINED IN THIS SET OF DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO THE CLIENT IS STRICTLY PROHIBITED. 1200 CONCORD AVENUE CONCORD, CA 94520 PREPARED FOR: RMobileT 2 06/20/25 ADDRESS JDX COMMENTS 3 03/25/26 ADDRESS JDX COMMENTS A&E FIRM: 1355 WINDWARD CONCOURSE, SUITE 410 ALPHARETTA, GA 30005 TEL: 678-990-2338 WIRE SIZE BURNDY LUG TYPE HS TYPE 2-YA-2 TYPE XA TYPE YA-2 TYPE GY #6 AWG GREEN INSULATED #2 AWG SOLID TINNED #2 AWG STRANDED #2/0 AWG STRANDED #4/0 AWG STRANDED TYPE VV TYPE VN TYPE NC TYPE SS TYPE GR YA6C-2TC38 YA3C-2TC38 YA2C-2TC38 YA26-2TC38 YA28-2N BURNDY GROUND LUG W/ LONG BARREL (SEE CHART) NUT (TYP) LOCK WASHER (TYP) TYPE VS BURNDY TWO HOLE LUG W/ LONG BARREL (SEE CHART) BARE WIRE TO BE NO-OX AT BOTH ENDS STRANDED (GREEN INSULATED) ONLY FOR #6 AWG (SEE CHART) TYPE VB TYPE PT TYPE GT² BOLT SIZE 1/2" - 16 NC S 2 BOLT 3/8" - 16 NC S 2 BOLT 3/8" - 16 NC S 2 BOLT 3/8" - 16 NC S 2 BOLT 3/8" - 16 NC S 2 BOLT HEAT SHRINK (CLEAR) GROUNDING CONDUCTOR GROUND BAR BOLT (SEE CHART) (TYP) STAINLESS STEEL BOLT (TYP) 2-HOLE CRIMP/ COMPRESSION CONNECTOR STAINLESS STEEL FLAT WASHER (TYP) GROUND BAR STAINLESS STEEL BELLVILLE WASHER (TYP) STAINLESS STEEL FLAT WASHER (TYP) STAINLESS STEEL NUT (TYP) STAINLESS STEEL BOLT STAINLESS STEEL FLAT WASHER DRAGON TOOTH WASHER (TYP) STEEL 3/8-11x1" TAMPER RESISTANT BOLT (TYP) INSULATORS SEE NOTE 2. (TYP) WALL BRACKET (TYP) 2-HOLE CRIMP/ COMPRESSION CONNECTOR STAINLESS STEEL BELLVILLE WASHER (TYP) STAINLESS STEEL FLAT WASHER (TYP) STAINLESS STEEL NUT (TYP) STAINLESS STEEL SELF-DRILLING METAL SCREW (TYP) UNIVERSAL COPPER GROUND BAR (4"x20") LOCK WASHER P/N M10 (TYP) TW0-HOLE COMPRESSION LUG 2-HOLE CRIMP/ COMPRESSION CONNECTOR DRAGON TOOTH WASHER (TYP) METALLIC OBJECT STAINLESS STEEL FLAT WASHER (TYP) NOTE: MINIMUM OF 3 THREADS TO BE VISIBLE (TYP) 2 HOLE LONG BARREL TINNED SOLID COPPER LUG (TYP) S/S NUT (TYP) S/S SPLIT WASHER (TYP) S/S FLAT WASHER (TYP) TIN COATED SOLID COPPER BUS BAR CHERRY INSULATOR INSTALLED IF REQUIRED S/S FLAT WASHER (TYP) S/S BOLT (TYP) NOTE: 1. ERICO EXOTHERMIC "MOLD TYPES" SHOWN HERE ARE EXAMPLES. CONSULT WITH CONSTRUCTION MANAGER FOR SPECIFIC MOLDS TO BE USED FOR THIS PROJECT. 2. MOLD TYPE ONLY TO BE USED BELOW GRADE WHEN CONNECTING GROUND RING TO GROUND ROD. CADWELD GROUNDING CONNECTIONS NOT TO SCALE SIGNAGE NOT TO SCALE NOTES: 1. ALL GROUNDING LUGS ARE TO BE INSTALLED PER MANUFACTURER'S SPECIFICATIONS. ALL HARDWARE BOLTS, NUTS, LOCK WASHERS SHALL BE STAINLESS STEEL. ALL HARDWARE ARE TO BE AS FOLLOWS: BOLT, FLAT WASHER,GROUND BAR, GROUND LUG, FLAT WASHER AND NUT. MECHANICAL LUG CONNECTION NOT TO SCALE LUG DETAIL NOT TO SCALESINGLE CONNECTOR AT METALLIC/STEEL OBJECTS SINGLE CONNECTOR AT STEEL OBJECTS SINGLE CONNECTOR AT GROUND BARS HARDWARE DETAIL (EXTERIOR CONNECTIONS) NOT TO SCALE NOTES: 1. DOWN LEAD (HOME RUN) CONDUCTORS ARE NOT TO BE INSTALLED ON CROWN CASTLE USA INC. TOWER, PER THE GROUNDING DOWN CONDUCTOR POLICY QAS-STD-10091. NO MODIFICATION OR DRILLING TO TOWER STEEL IS ALLOWED IN ANY FORM OR FASHION, CAD-WELDING ON THE TOWER AND/OR IN THE AIR IS NOT PERMITTED. 2. OMIT INSULATOR WHEN MOUNTING TO TOWER STEEL OR PLATFORM STEEL USE INSULATORS WHEN ATTACHING TO BUILDINGS OR SHELTERS. GROUND BAR DETAIL NOT TO SCALE GROUNDING DETAILS 03/25/26 s<s<.J-b.J-b,,.a=,,.a=-------- ,, Jo s a I 5 u · or, o California in ord 4 t , N twor to c • on . e alf of com an , Am ,o o I air th. n cessary Busines Lie nses/,Permi for I, I c.,i in ma el, c ly, lid fr,om January 13, 2026 h�o,ug January 3 , 2027. thoriz personnel ;· clud : na Coeur nn Coo rianne 1Oliver Bla e Som en Fri12 Chang Garre a orne lza e Mobley Jame, (Jimmy} Si man Jarr tt Ellin on Jesus Diaz us V a er ri y ic l ' S ,v n T n .-, a.:c r on o o rtJ u H n Z fl n by OU 1 V n CITY OF SANTA ANA Planning" and Building Agency CALIFORNIA ALLUPURPOSE ACKNOWLEDGMENT 4 FOR PERMIT ISSUANCE RYA t e CO.! A notary public or other officer completing this certificate verifies only the identity of the individmil document to which this certificate is attacheranrr,r t the ttt,fiAme. arri irary nr valirlity of +hit rinr%"mnnt State of Ca County of lifornia On JAN U A g=4Z 13 202 b 6ate personally appeared before me, y, y N CITY 9 • � Nf*T* LIAIV A 1 Nosey Fba (two C Here Insert Name and Title of the Officer "16 Name(s) of Signer(s) who proved to me on the basis of satisfactory evidence to be the person(s) whose name(s) is/are subscribed to the within instrument and acknowledged to me that he/she/they executed the same in his/her/their authorized capacity(ies), and that by his/her/their signature(s) on the instrument the person(s), or the entity upon behalf of which the person(s) acted, executed the instrument. certify under PENALTY OF PERJURY under the laws of the State of California that the foregoing paragraph is true and correct. • 4 MULQf y rLiVIrL. " %01111VI 1110 Los Angeles County Place Notary Seal Above WITNESS my hand and official seal. Signature Signature otaty Public OPTIONAL Though this section is optional, completing this information can deter alteration of the document or fraudulent reattachment of this form to an unintended document. Description of Attached Documej Title or Type of Document: -A)-Wq� Number of Pages: / Signe t r(s) Other Capacity(les) Claimed by Signer(s) Signer's Name:..., aot NWAM A W 0 2 Corporate Officer — Title(s): Tgfffij O Partner — O Limited D Individual O Trustee El General LJ Attorney in Fact O Guardian or Conservator E Other: Signer Is Representing: VK-a' A&4MX(4-1zAWocument Date: Than Named Above: Signer's Name: 1:1 Corporate Office EJ Partner — ❑ Li 1:1 Individual 0 Truste r - S): d L01 General El Attorney in Fact ❑ Guardian or Conservator O O r: S er Is Representing: • w�cdvc�.•cec,^roc.^cx sx^sdxx,^s:<>�c�c.,s;c,�cxxx.�c.^ws�.Y v�s c^ct.^u,�.�c^s�ca�:c.�:csw;o�c^s�xn c.�s cr 02014 National Notary Association • www.NationalNotary.org • 1-800-US N01ARY (1-800-876-6827) Item #5907