HomeMy WebLinkAbout2306 W Manly Ave - PlanSCOPE OF WORK GENERAL NOTES
VICINITY MAPABBREVIATIONS
A AMPERE
AC ALTERNATING CURRENT
AFC ARC FAULT CIRCUIT INTERUPTER
AZIM AZIMUTH
COMP COMPOSITION
DC DIRECT CURRENT
(E)EXISTING
ESS ENERGY STORAGE SYSTEM
MSP MAIN SERVICE PANEL
(N)NEW
PRE-FAB PRE-FABRICATED
PSF POUNDS PER SQUARE FOOT
PV PHOTOVOLTAIC
RSD RAPID SHUTDOWN DEVICE
TL TRANSFORMERLESS
V VOLTS
W WATTS
SHEET INDEX
PAGE
REV: A 4/27/2026
JAMES POBOG
2306 W MANLY AVE, SANTA
ANA, CA, 92704
PROJECT NUMBER:
109R-306POBO2 PR-3005088446
SHEET
DESIGNER:
SREERAJ P R
CUSTOMER RESIDENCE:
TEL. (714) 788-0787
APN: 412-253-53
(415) 580-6920 ex3
PV-1.0
#ESTAMP#SSTAMP
2500 WHITE RD. SUITE A, IRVINE CA 92614
PHONE 805.540.7603
FAX 949.215.7778
CA CL #750184
GILBERT CORREIA, C10, C46
COVER SHEETREV NAME DATE COMMENTS
• ALL WORK SHALL GENERALLY CONFORM WITH 2025 CRC/CBC/CEBC, 7-22 ASCE & 2024 NDS, MUNICIPAL CODE, AND ALL
MANUFACTURERS' LISTINGS AND INSTALLATION INSTRUCTIONS.
• PHOTOVOLTAIC SYSTEM WILL COMPLY WITH CEC 2025.
• ELECTRICAL SYSTEM GROUNDING WILL COMPLY WITH CEC 2025.
• PHOTOVOLATIC SYSTEM IS UNGROUNDED. NO CONDUCTORS ARE SOLIDLY GROUNDED IN THE INVERTER. SYSTEM
COMPLIES WITH 690.41(A)
• MODULES CONFORM TO AND ARE LISTED UNDER UL 61730.
• INVERTER CONFORMS TO AND IS LISTED UNDER UL 1741.
• RACKING CONFORMS TO AND IS LISTED UNDER UL 2703.
• SNAPNRACK RACKING SYSTEMS, IN COMBINATION WITH TYPE I, OR TYPE II MODULES, ARE CLASS A FIRE RATED.
• RAPID SHUTDOWN SYSTEM IN COMPLIANCE WITH CEC 2025 690.12(B)(1) WHERE CONDUCTORS OUTSIDE OF THE
ARRAY ARE LIMITED TO LESS THAN 30V IN 30 SECONDS AND CEC 2025 690.12(B)(2)(2) WHERE CONDUCTORS INSIDE
THE ARRAY BOUNDARY IS LIMITED TO LESS THAN 80V IN 30 SECONDS
• CONSTRUCTION FOREMAN TO PLACE CONDUIT RUN PER 690.31(D).
• ARRAY DC CONDUCTORS ARE SIZED FOR DERATED CURRENT.
• 13.93 AMPS MODULE SHORT CIRCUIT CURRENT.
• 21.77 AMPS DERATED SHORT CIRCUIT CURRENT [690.8 (a)(1) & 690.8 (b)].
• ENERGY STORAGE SYSTEM CONFORMS TO AND IS LISTED UNDER UL 9540.
• ENERGY STORAGE SYSTEM LIVE PARTS ARE NOT ACCESSIBLE DURING ROUTINE MAINTENANCE. SYSTEM
VOLTAGE IN ACCORDANCE WITH CEC 706.20 AND EXCEPTION 1 CEC 706.20 (B).
• ADDITIONAL DISCONNECTING MEANS SHALL BE INSTALLED WHERE THE CIRCUITS FROM THESE TERMINALS PASS
THROUGH A WALL OR PARTITION PER 706.15(D).
• LISTED, COMBINATION TYPE AFCI SHALL BE INSTALLED WHERE BACKED UP CIRCUIT WIRING IS EXTENDED MORE
THAN 6FT AND DOES NOT INCLUDE ANY ADDITIONAL OUTLETS OR DEVICES PER CEC 210.12(D).
• ALL PASS-THROUGH CONDUCTORS MUST COMPLY WITH CEC 312.8
• THE CAPACITY OF THE STANDALONE SYSTEM SUPPLY SHALL BE EQUAL TO OR GREATER THAN THE LOAD POSED
BY THE SINGLE LARGEST UTILIZATION EQUIPMENT CONNECTED TO THE SYSTEM PER CEC ARTICLE 710.15(A)
• SYSTEM SIZE: 3.28KW DC, 11.5KW AC
(E)SYSTEM SIZE: 4.095KW DC, 3.8KW AC
COMBINED SYSTEM SIZE: 8.195KW DC, 15.3KW AC
• MODULES: (8) LONGI GREEN ENERGY TECHNOLOGY CO
LTD: LR5-54HPB-410M
• RAPID SHUTDOWN: (3) TESLA MID CIRCUIT INTERRUPTER
(MCI) ROOFTOP MODULE LEVEL RAPID SHUTDOWN DEVICE
• ENERGY STORAGE SYSTEM: (1) TESLA: POWERWALL 3
1707000-XX-Y, 13.5 KWH.
(1) TESLA: POWERWALL 3 EXPANSION 1807000-XX-Y
TOTAL ENERGY CAPACITY: (IN KWH): 27KWH
• RACKING: ULTRAFOOT [ANCHOR] RAIL TO DECK
SNR-DC-01507
• POWER-CONTROLLED SYSTEM (PCS) ENABLED EQUIPMENT
INSTALLED, SEE PV-4.0 FOR INTERCONNECTION DETAILS
• EXISTING SOLAR SYSTEM INSTALLED.
PAGE # DESCRIPTION
PV-1.0 COVER SHEET
PV-2.0 SITE PLAN
PV-3.0 LAYOUT
PV-3.1 MOUNTING DETAIL
PV-4.0 ELECTRICAL
PV-4.1 ELECTRICAL CALCS
PV-4.2 ELECTRICAL CALCS
PV-4.3 PANEL SCHEDULE
PV-5.0 SIGNAGE
PV-5.1 SIGNAGE 2
2306 W Manly Ave
Santa Ana CA
US 92704
• NEW 125AMP LOAD CENTER TO BE INSTALLED.
PL
PL
PL
PL
PLPL
PL
PL
PL
PL
PL PL
PAGE
REV: A 4/27/2026
JAMES POBOG
2306 W MANLY AVE, SANTA
ANA, CA, 92704
PROJECT NUMBER:
109R-306POBO2 PR-3005088446
SHEET
DESIGNER:
SREERAJ P R
CUSTOMER RESIDENCE:
TEL. (714) 788-0787
APN: 412-253-53
(415) 580-6920 ex3
PV-2.0
#ESTAMP#SSTAMP
2500 WHITE RD. SUITE A, IRVINE CA 92614
PHONE 805.540.7603
FAX 949.215.7778
CA CL #750184
GILBERT CORREIA, C10, C46
SITE PLAN
MAIN PANEL
DEDICATED PV METER
SERVICE ENTRANCESE
MP
PMSUB-PANELSP
LEGEND SCALE: NTS
NOTE: NOT ALL ITEMS IN LEGEND
WILL APPEAR IN SITE PLAN
ENERGY STORAGE
SYSTEM (ESS)
GP GENERATION PANEL
INVERTER(S)
AC DISCONNECT(S)
DC DISCONNECT(S)
INTERIOR EQUIPMENT
SHOWN AS DASHEDINV
AC
DC
METER ADAPTERMABATTERY
BP BACKUP LOADS PANEL MD MICROGRID
INTERCONNECT DEVICE
PV LOAD CENTERLC METER ADAPTER
CONTROLLER CB IQ COMBINER BOXMAC
RDS REMOTE DISCONNECT
SWITCH
SITE PLAN - SCALE = 1/16" = 1'-0"
NOTES:
·RESIDENCE DOES NOT CONTAIN ACTIVE FIRE
SPRINKLERS.
ARRAY DETAILS:
·TOTAL ROOF SURFACE AREA: 2289 SQ FT.
·TOTAL EXISTING PV ARRAY AREA: 229 SQ FT.
·TOTAL NEW PV ARRAY AREA: 168.2 SQ FT.
·TOTAL PV ARRAY AREA: 397.2 SQ FT.
·PERCENTAGE PV COVERAGE:
(TOTAL PV ARRAY AREA/TOTAL ROOF SURFACE
AREA) * 100 = 17.351682 %
RAIL
STANDOFFS &
FOOTINGS
SOLAR
MODULES
ARRAY
PITCH
PV AREA
(SQFT)
AR-01 18° 105.11
AR-02 18° 63.07360°
TRUE
AZIM
MAG
AZIM
168°180°
348°
ESS SHALL BE INSTALLED 3FT FROM DOORS AND WINDOWS
IN ACCORDANCE WITH R330.4. ESS UNITS SHALL BE
SEPARATED FROM EACH OTHER BY NOT LESS THAN 3 FEET
EXCEPT WHERE SMALLER SEPARATION DISTANCES ARE
DOCUMENTED TO BE ADEQUATE BASED ON LARGE/SCALE
FIRE TESTING.
NOTE: ROOFTOP MODULE LEVEL RAPID
SHUTDOWN DEVICE INSTALLED PER CEC
690.12
(E) RESIDENCE
(N) ARRAY AR-01
(N) ARRAY AR-02
FIRE SETBACKS
(18" TYP)
ROOF PATHWAYS
(3' TYP)
ROOF PATHWAYS
(3' TYP)
(E) PV ARRAY
(E) PV
EQUIPMENT
W MANLY AVE
(E) FENCE
(E) GATE
SE
MP
MD
RDS
INV
AC
LC
AC
AC INV
(E)SHED
(E)CHIMNEY
Exp. 12/31/2026Digitally Signed On: 04/28/2026
PAGE
REV: A 4/27/2026
JAMES POBOG
2306 W MANLY AVE, SANTA
ANA, CA, 92704
PROJECT NUMBER:
109R-306POBO2 PR-3005088446
SHEET
DESIGNER:
SREERAJ P R
CUSTOMER RESIDENCE:
TEL. (714) 788-0787
APN: 412-253-53
(415) 580-6920 ex3
PV-3.0
#ESTAMP#SSTAMP
2500 WHITE RD. SUITE A, IRVINE CA 92614
PHONE 805.540.7603
FAX 949.215.7778
CA CL #750184
GILBERT CORREIA, C10, C46
LAYOUT
SOLAR MODULE
SNAPNRACK
RACKING
MODULE ELEVATION DETAIL - SCALE: NTS
4.5"
DESIGN CRITERIA
MAX DISTRIBUTED LOAD: 3 PSF
SNOW LOAD: 3 PSF
WIND SPEED:
95 MPH 3-SEC GUST.
FASTENERS:
(2) DECK ANCHORS FULLY
PENETRATING THROUGH WOOD
DECK
STRUCTURAL NOTES
• ATTACHMENTS FOR THIS INSTALLATION ARE DESIGNED FOR A STANDARD WOOD
FRAMED ROOF STRUCTURE FREE FROM DAMAGE, DETERIORATION, OR MODIFICATION
THAT WOULD COMPROMISE ITS ORIGINAL DESIGN INTEGRITY. INSTALLERS SHALL
OBSERVE THE FRAMING FOR CONFORMANCE TO THE BELOW REQUIREMENTS AND
NOTIFY THE ENGINEER OF ANY POTENTIAL STRUCTURAL ISSUES FOR GUIDANCE
PRIOR TO PROCEEDING WITH INSTALLATION.
ⅰ: MINIMUM 2x WOOD FRAMING (NOMINAL) FREE FROM DAMAGE, DETERIORATION, OR
MODIFICATION
ⅱ: FRAMING SPACING AT 24" O.C. MAX
ⅲ: FASTENER SHALL BE EMBEDDED INTO COMPETENT MATERIAL
• IF ARRAY (EXCLUDING SKIRT) IS WITHIN 12" (48" FOR TILT KITS) BOUNDARY REGION OF
ANY ROOF PLANE EDGES (EXCEPT VALLEYS),
THEN ATTACHMENTS NEED TO BE ADDED AND OVERHANG REDUCED WITHIN THE 12"
(48" FOR TILT KITS) BOUNDARY REGION ONLY AS
FOLLOWS:
•• ALLOWABLE ATTACHMENT SPACING INDICATED ON PLANS TO BE REDUCED BY 50%.
•• ALLOWABLE OVERHANG INDICATED ON PLANS TO BE 1/5TH OF ALLOWABLE
ATTACHMENT SPACING INDICATED ON PLANS.
• INSTALLERS SHALL NOTIFY ENGINEER OF ANY POTENTIAL STRUCTURAL ISSUES
OBSERVED PRIOR TO PROCEEDING W/ INSTALLATION.
ROOF INFO ATTACHMENT INFORMATION
Name Type Height Detail Max Landscape
OC Spacing
Max Landscape
Overhang
Max Portrait
OC Spacing
Max Portrait
Overhang Configuration
AR-01 COMP SHINGLE - UR - ULTRAFOOT [DECKANCHOR]1-STORY ULTRAFOOT [ANCHOR] RAIL TO DECK SNR-DC-01507 4'-10" 0'-6" 4'-10" 0'-6" STAGGERED
AR-02 COMP SHINGLE - UR - ULTRAFOOT [DECKANCHOR]1-STORY ULTRAFOOT [ANCHOR] RAIL TO DECK SNR-DC-01507 4'-10" 0'-6" 4'-10" 0'-6"STAGGERED
D1 - AR-01 - SCALE: 3/32" = 1'-0"
AZIM: 180°
PITCH: 18°
D2 - AR-02 - SCALE: 3/32" = 1'-0"
AZIM: 360°
PITCH: 18°11'-3"
5'-8"
19'-1"20'-2"
1'-7"
13'-4"
11'-3"
11'-4"
20'-1"19'-2"
2'-11"
5'-7"
(E)CHIMNEY (E) PV ARRAY Exp. 12/31/2026Digitally Signed On: 04/28/2026
FOR SNAPNRACK ENGINEERING TO APPLY, THE EMBEDMENT CRITERIA SHOWN
HEREIN MUST BE MET (IF CRITERIA CANNOT BE MET OR SPANS ARE NOT
SUFFICIENT, CONTACT SNAPNRACKFOR SUPPORT):
REFER TO SNAPNRACK INSTALLATION MANUAL FOR 5 16"Ø HARDWARE TORQUE
SPECIFICATIONS. REFER TO MANUFACTURER SPECIFICATIONS FOR OTHER FASTENER
TORQUE REQUIREMENTS.
FOR DECK MOUNT ATTACHMENT: MINIMUM 3 8" SHEATHING REQUIRED. FASTENER
MUST EMBED INTO COMPETENT MATERIAL.
REFER TO ATTACHMENT INFORMATION TABLE ON LAYOUT PAGE FOR LOAD PATH
(INSTALL TYPE).
EXPLODED
BUTYL PAD
5 16"n-18 X 1", SS
BOLT, WIDE FLANGE,
RECESSED
ULTRA RAIL SPRING
ULTRAFOOT BASE
ANCHOR
ULTRAFOOT FLIP CLAMP
THRU
ULTRAFOOT FLIP CLAMP
TAPPED
TOP
.374"
.217"
RAFTER ATTACHMENT
DETAIL SECTION VIEW
ROOF DECKING, TYP.
ROOF RAFTER, TYP.
FASTENER HEIGHT
OFF ROOF:
5/16"
MODULE HEIGHT MAX:
UR-40 = 4 1/2"
UR-45 = 4 1/2"
UR-60 = 5 1/8"
MIN 2 1/2"
EMBEDMENT
(X1) 5 16"n S.S. LAG
SCREW
SNAPNRACK, ULTRA RAIL
ULTRAFOOT
ANCHOR
FASTENER CONFIGURATIONS
(X2) DECKANCHORS
INTO WOOD DECK
(X1) LAG INTO
RAFTER DECK ATTACHMENT DETAIL
SECTION VIEW
COMP SHINGLE ROOFING, TYP
ROOF DECKING, TYP
SNAPNRACK, ULTRA RAIL
FASTENER HEIGHT
OFF ROOF:
5/16"
MODULE HEIGHT, MAX:
UR-40 = 4 1/2"
UR-45 = 4 1/2"
UR-60 = 5 1/8"
(X2) DECK
ANCHOR
INTO WOOD DECK
MINIMUM 3/8" SCREW
EMBEDMENT INTO DECKING
PAGE
REV: A 4/27/2026
JAMES POBOG
2306 W MANLY AVE, SANTA
ANA, CA, 92704
PROJECT NUMBER:
109R-306POBO2
SHEET
DESIGNER:
SREERAJ P R
CUSTOMER RESIDENCE:
TEL. (714) 788-0787
APN: 412-253-53
(415) 580-6920 ex3
PV-3.1
#ESTAMP#SSTAMP
2500 WHITE RD. SUITE A, IRVINE CA 92614
PHONE 805.540.7603
FAX 949.215.7778
CA CL #750184
GILBERT CORREIA, C10, C46
MOUNTING DETAIL
DESIGNER:
APPROVED BY:
M.AFFENTRANGER
DRAFTER: H.WULFEKOETTER
M.AFFENTRANGER
SCALE:
DATE:
NTS
8/26/2024
DRAWING NUMBER:
SNR-DC-01507Solar Mounting Solutions
Sunrun South LLC
595 MARKET STREET, 29TH FLOOR SAN FRANCISCO, CA 94105 USA
PHONE (415) 580-6900 FAX (415) 580-6902
THE INFORMATION IN THIS DRAWING IS CONFIDENTIAL AND PROPRIETARY. ANYREPRODUCTION, DISCLOSURE, OR USE THEREOF IS PROHIBITED WITHOUT THEWRITTEN CONSENT OF SUNRUN SOUTH LLC.
Exp. 12/31/2026Digitally Signed On: 04/28/2026
FACILITY
GROUND
120/240 VAC
SINGLE PHASE
SERVICE EXISTING 100A
MAIN
BREAKER -CENTER FED
EXISTING 125A
MAIN PANEL
125A BUS
4
NEW 125 A LOAD CENTERM
TESLA
BACKUP
SWITCH
METER NUMBER: SCE 222012-828660
70A 60A
UL 9540
FACTORY
WIRING
ASSEMBLY
(1 ) TESLA
POWERWALL 3
EXPANSION PACK 1807000-xx-y
(N) IMO PE69-3020,
DISCONNECT
SWITCH, 3P, 16A
INVERTER: TESLA
POWERWALL 3 1707000-XX-Y,
ENERGY STORAGE:
TESLA:POWERWALL 3
1707000-XX-Y 11500 WATT INVERTER
LOAD RATED DC DISCONNECT
WITH AFCI RAPID SHUTDOWN COMPLIANT,
POWER CONTROL SYSTEM
3
J-BOX
12
• POINT OF INTERCONNECTION: CEC 2025 705.13, PCS
• EQUIPMENT CHARACTERISTICS INCLUDED
IN SPEC SHEETS
• NOTE: COMBINED SYSTEM BACKFEED = 80.0A USED FOR INTERCONNECTION CALCULATIONS
J-BOX
EE
13 Existing Hanwha Q CELLS:
Q.PEAK BLK-G5 315 Modules
Existing SolarEdge
Technologies: SE3800H-USE
Existing Inverter(s)
8 LONGI GREEN ENERGY TECHNOLOGY CO LTD
LR5-54HPB-410M
STRING 1 WITH 5 MODULES
WITH 2 MCI COUNT
STRING 2 WITH 3 MODULES
WITH 1 MCI COUNT , MODULE LEVEL RAPID SHUTDOWN DEVICES
(N) LOCKABLE
BLADE TYPE
AC DISCONNECT
SQUARE D
DU222RB
3R, 60A, 2P
120/240VAC
3
E
(N) TESLA REMOTE METER
(1) SOLAR PV CURRENT
TRANSFORMER
(N) 60A PV + ESS BREAKER
(E) 20A PV BREAKER
AC DISCONNECT
E
AC DISCONNECT
E
E
Existing Existing
PAGE
REV: A 4/27/2026
JAMES POBOG
2306 W MANLY AVE, SANTA
ANA, CA, 92704
PROJECT NUMBER:
109R-306POBO2 PR-3005088446
SHEET
DESIGNER:
SREERAJ P R
CUSTOMER RESIDENCE:
TEL. (714) 788-0787
APN: 412-253-53
(415) 580-6920 ex3
PV-4.0
#ESTAMP#SSTAMP
2500 WHITE RD. SUITE A, IRVINE CA 92614
PHONE 805.540.7603
FAX 949.215.7778
CA CL #750184
GILBERT CORREIA, C10, C46
ELECTRICAL
CONDUIT SCHEDULE
TAG CIRCUIT DESCRIPTION CONDUCTOR NEUTRAL GROUND CONDUIT
1 Inverter Input (4) 10 AWG (PV WIRE)N/A 6 AWG (BARE)Open Air
2 Inverter Input (4) 10 AWG
THHN/THWN-2 N/A 8 AWG THHN/THWN-2 3/4" EMT
3 Inverter Output (2) 6 AWG
THHN/THWN-2
(1) 6 AWG
THHN/THWN-2 10 AWG THHN/THWN-2 3/4" EMT
4 Load center Feeder (2) 4 AWG
THHN/THWN-2
(1) 4 AWG
THHN/THWN-2 8 AWG THHN/THWN-2 1" EMT
E Existing
PAGE
REV: A 4/27/2026
JAMES POBOG
2306 W MANLY AVE, SANTA
ANA, CA, 92704
PROJECT NUMBER:
109R-306POBO2 PR-3005088446
SHEET
DESIGNER:
SREERAJ P R
CUSTOMER RESIDENCE:
TEL. (714) 788-0787
APN: 412-253-53
(415) 580-6920 ex3
PV-4.1
#ESTAMP#SSTAMP
2500 WHITE RD. SUITE A, IRVINE CA 92614
PHONE 805.540.7603
FAX 949.215.7778
CA CL #750184
GILBERT CORREIA, C10, C46
ELECTRICAL CONT.
MODULE CHARACTERISTICS
LONGI GREEN ENERGY
TECHNOLOGY CO LTD:
LR5-54HPB-410M
410 W
OPEN CIRCUIT VOLTAGE 37.40 V
MAX POWER VOLTAGE 31.42 V
SHORT CIRCUIT CURRENT 13.93 A INSTALLER MUST CHECK THE CONDITION,
INSTALLABILITY AND CODE COMPLIANCE OF
EXISTING EQUIPMENT.POWER CONTROL SYSTEM (PCS):
• A PCS IS INSTALLED IN ACCORDANCE WITH
CEC 705.13
• THE PCS SHALL LIMIT GENERATION
SOURCE OUTPUT SUCH THAT CURRENT FROM
ALL SOURCES OF SUPPLY DOES NOT EXCEED
THE RATING OF ANY BUSBAR OR
CONDUCTOR SUPPLIED BY THE POWER
PRODUCTION SOURCES
• ANY BUSBAR OR CONDUCTOR ON THE
LOAD SIDE OF THE SERVICE DISCONNECT
NOT MONITORED BY THE PCS SHALL COMPLY
WITH ARTICLE 705.12.
• ACCESS TO PCS CONTROLS IS
RESTRICTED TO QUALIFIED PERSONS IN
ACCORDANCE WITH 240.6(C).
• INVERTER 1: Tesla:Powerwall 3 1707000-xx-y
• ENABLE PCS; SETPOINTS:
- 56A - MAXIMUM TOTAL CURRENT ON
THE CONTROLLED PANEL
- 0A - FAIL SAFE GENERATION
BACKFEED CURRENT SUPPLY (120%
COMPLIANT)
General Notes:
• CITY REQUIRES TWO SOURCES OF GROUND - UFER, TWO GROUNDS RODS OR
COLD WATER GAS BOND
• INSTALL THE BACKED UP LOAD CONDUCTORS AND THE MICROGRID
INTERCONNECTION DEVICE BREAKER CONDUCTORS IN TWO SEPARATE
CONDUITS.
ANY MULTIWIRE BRANCH CIRCUITS RELOCATED ARE TO BE IDENTIFIED,
GROUPED, AND EQUIPPED WITH A 2-POLE OCPD BREAKER PER CEC 210.4(B,D).
IF THE RELOCATED LOADS EXTEND MORE THAN 6 FEET, AFCI PROTECTION
APPLIES PER 2019 CEC 210.12
BACKUP LOADS
LOAD BREAKER RATING
(AMPS)LABEL DEMAND
LOAD
1 20A-1P OUTLETS 1500 W
2 20A-1P WORK LTS 1500 W
3 20A-1P KIT 1500 W
4 20A-1P KIT 1500 W
5 30A-2P DRYER 5760W
6 50A-2P RANGE 9600W
7 15A-1P LITE SWITCHES 1500 W
8 15A-1P BED LIGHTS 1500 W
9 20A-1P KIT 1500 W
10 20A-1P KIT 1500 W
11 20A-1P DW 1500 W
12 20A-1P DW 1500 W
13 30A-2P AC 5760 W
14 20A-1P BATH 1500 W
15 20A-1P OUTLET 1500 W
16 15A-2P TRM 2880 W
Inverter Calculations
Each Inverter has the following values which are calculated following these formulas:
Inverter X:
•Max DC Circuit Current = (Module Isc) x (High Irradiance)(690.8(A)(1)(a))
•Max AC Output Current = (Max Inverter Output)
•OCPD Needed = (Max AC Output Current) x 1.25
•System Characteristics:
•Operating Voltage = (Module Vmp) x (# Modules / String)
•Max Open Circuit Voltage = [((Temp Coef Voc) x (Voc)) / 100] x (Low Temp - STC Temp) + Voc
* (# Modules / String)
•Operating Current = (Module Imp) x (# Strings)
•Short Circuit Current = 1.25 x (Module Isc) x (# Strings)Inverter Powerwall 3 1707000-xx-y
•Max DC Circuit Current = 17.42A
•Max AC Output Current = 48A
•OCPD Needed = 60A
•System Characteristics:
•Operating Voltage = 157.11V
•Max Open Circuit Voltage = 200.64V
•Operating Current = 26.1A
•Short Circuit Current = 34.84A
Allowable Backfeed:
Max Allowed Total Generation Backfeed OCPD =
Main Breaker Rating = 100 A
70 A ≤ 100 A → Interconnection
Meets CEC 2025 705.13 Requirements
Wire Calculations
Wire ampacity calculated from CEC 310.16/310.17 as appropriate with ambient temperature
calculations from CEC 310.15(B)(1)(1) and raceway fill adjustments from CEC 310.15(C)(1).
Conduit on the roof shall be installed no less than 1" above the roof deck. PV Circuit conductor
ampacity is constrained using the 75°C column with the continuous duty uprating or the 90°C
column with the relevant ambient temperature and raceway fill adjustments without the continuous
duty uprating per 690.8(B), whichever is the lower value will govern conductor sizing. Non-PV
Circuit Conductors use the ampacity in the 75°C column or the 90°C column with the relevant
ambient temperature and raceway fill adjustments, whichever is less (110.14(C) & 310.15(A)(2)).
The rating of the conductor after adjustments shall be greater than, or equal to, the continuous
duty uprated current.
Calc Ex: Wire Ampacity x Ambient Temp. Corr. Factor x Conduit Fill Adj. Factor >= Output Current
•Tag 1: Inverter Input: 10 AWG rated 35A as per 75°C, 36.4A as per 90°C with adjustements >=
21.77A
•Tag 2: Inverter Input: 10 AWG rated 35A as per 75°C, 29.12A as per 90°C with adjustements >=
21.77A
•Tag 3: Inverter Output: 6 AWG rated 65A as per 75°C, 68.25A as per 90°C with adjustements >=
60.0A
•Tag 4: Load center Feeder: 4 AWG rated 85A as per 75°C, 86.45A as per 90°C with adjustements
>= 70.0A
PAGE
REV: A 4/27/2026
JAMES POBOG
2306 W MANLY AVE, SANTA
ANA, CA, 92704
PROJECT NUMBER:
109R-306POBO2 PR-3005088446
SHEET
DESIGNER:
SREERAJ P R
CUSTOMER RESIDENCE:
TEL. (714) 788-0787
APN: 412-253-53
(415) 580-6920 ex3
PV-4.2
#ESTAMP#SSTAMP
2500 WHITE RD. SUITE A, IRVINE CA 92614
PHONE 805.540.7603
FAX 949.215.7778
CA CL #750184
GILBERT CORREIA, C10, C46
ELECTRICAL CALCS
PAGE
REV: A 4/27/2026
JAMES POBOG
2306 W MANLY AVE, SANTA
ANA, CA, 92704
PROJECT NUMBER:
109R-306POBO2 PR-3005088446
SHEET
DESIGNER:
SREERAJ P R
CUSTOMER RESIDENCE:
TEL. (714) 788-0787
APN: 412-253-53
(415) 580-6920 ex3
PV-4.3
#ESTAMP#SSTAMP
2500 WHITE RD. SUITE A, IRVINE CA 92614
PHONE 805.540.7603
FAX 949.215.7778
CA CL #750184
GILBERT CORREIA, C10, C46
PANEL SCHEDULE
20
20
10
0
EXISTING 125/100A MAIN
PANEL WITH 125 A BUSBAR
NEW 125A LOAD CENTER
60
20
NEW PV+ESS
BREAKER
(E)PV BREAKER
50
3
0
30
20
20
1
5
15
20
20
20
20
30
20
20
15 TRM BREAKER
OUTLETSWORK LTSKITKITDRYER
DRYERRANGE
LITE SWITCHESBED LIGHTSKITKITDWDW
AC
BATHOUTLET
MAIN
BREAKER
Product datasheet
Characteristics
HOM1224L125PRB
Main
Product or component type Load Center
Range of product Homeline
Load center type Main lugs
Line Rated Current 125 A
Number of spaces 12
Number of circuits 24
NEMA degree of protection NEMA 3R outdoor
Cover type Surface cover
Electrical connection Lugs
Complementary
Short-circuit current 10 kA
Number of tandem circuit breakers 12
Phase 1 phase
System Voltage 120/240 V AC
WG gauge WG 6...AWG 2/0 (aluminium)
WG 6...AWG 1 (copper)
Wiring configuration 3-wire
Cover finish Gray baked enamel
Material Tin plated aluminium busbar
Enclosure material Welded galvannealed steel
Surface finish Baked enamel grey
Box number 3R
Height 29.84 in (758 mm)
Width 14.76 in (375 mm)
Depth 4.53 in (115 mm)
Environment
product certifications UL E-6294
Offer Sustainability
Green Premium product Green Premium product
Compliant - since 1414 - Schneider Electric declaration
of conformity
Compliant - since 1414 - Schneider Electric declaration of conformity
Reference not containing SVHC above the threshold Reference not containing SVHC above the threshold
vailable vailable
Need no specific recycling operations Need no specific recycling operations
WARNING: This product can expose you to chemicals
including:
WARNING: This product can expose you to chemicals including:
Lead and lead compounds which is known to the State
of California to cause cancer and birth defects or other
reproductive harm.
Lead and lead compounds which is known to the State of California to cause cancer
and birth defects or other reproductive harm.
For more information go to www.p65warnings.ca.gov For more information go to www.p65warnings.ca.gov
Th
e
i
n
f
o
r
m
a
t
i
o
n
p
r
o
v
i
d
e
d
i
n
t
h
i
s
d
o
c
u
m
e
n
t
a
t
i
o
n
c
o
n
t
a
i
n
s
g
e
n
e
r
a
l
d
e
s
c
r
i
p
t
i
o
n
s
a
n
d
/
o
r
t
e
c
h
n
i
c
a
l
c
h
a
r
a
c
t
e
r
i
s
t
i
c
s
o
f
t
h
e
p
e
r
f
o
r
m
a
n
c
e
o
f
t
h
e
p
r
o
d
u
c
t
s
c
o
n
t
a
i
n
e
d
h
e
r
e
i
n
.
Th
i
s
d
o
c
u
m
e
n
t
a
t
i
o
n
i
s
n
o
t
i
n
t
e
n
d
e
d
a
s
a
s
u
b
s
t
i
t
u
t
e
f
o
r
a
n
d
i
s
n
o
t
t
o
b
e
u
s
e
d
f
o
r
d
e
t
e
r
m
i
n
i
n
g
s
u
i
t
a
b
i
l
i
t
y
o
r
r
e
l
i
a
b
i
l
i
t
y
o
f
t
h
e
s
e
p
r
o
d
u
c
t
s
f
o
r
s
p
e
c
i
f
i
c
u
s
e
r
a
p
p
l
i
c
a
t
i
o
n
s
.
It
i
s
t
h
e
d
u
t
y
o
f
a
n
y
s
u
c
h
u
s
e
r
o
r
i
n
t
e
g
r
a
t
o
r
t
o
p
e
r
f
o
r
m
t
h
e
a
p
p
r
o
p
r
i
a
t
e
a
n
d
c
o
m
p
l
e
t
e
r
i
s
k
a
n
a
l
y
s
i
s
,
e
v
a
l
u
a
t
i
o
n
a
n
d
t
e
s
t
i
n
g
o
f
th
e
p
r
o
d
u
c
t
s
w
i
t
h
r
e
s
p
e
c
t
t
o
t
h
e
r
e
l
e
v
a
n
t
s
p
e
c
i
f
i
c
a
p
p
l
i
c
a
t
i
o
n
o
r
u
s
e
t
h
e
r
e
o
f
.
Ne
i
t
h
e
r
S
c
h
n
e
i
d
e
r
E
l
e
c
t
r
i
c
I
n
d
u
s
t
r
i
e
s
S
A
S
n
o
r
a
n
y
o
f
i
t
s
a
f
f
i
l
i
a
t
e
s
o
r
s
u
b
s
i
d
i
a
r
i
e
s
s
h
a
l
l
b
e
r
e
s
p
o
n
s
i
b
l
e
o
r
l
i
a
b
l
e
f
o
r
m
i
s
u
s
e
o
f
t
h
e
i
n
f
o
r
m
a
t
i
o
n
c
o
n
t
a
i
n
e
d
h
e
r
e
i
n
.
1 / 1
This Verification is for the exclusive use of Intertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms
and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this
Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material,
product or service must first be approved in writing by Intertek. The observations and test/inspection results referenced in this Verification are relevant only to the sample tested/inspected. This
Verification by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.
Intertek Page 1 of 8 GFT-OP-11a (22-August-2019)
Test Verification of Conformity
Verification Number: 104514208CRT-001VOC
Applicant Name & Address:
Tesla Inc.
3500 Deer Creek Road, Palo Alto, CA 94304
Product Description:
Energy Storage System Grid Support Utility Interactive & Standalone Inverter
Ratings & Principle
Characteristics:
See Appendix 2
Models/Type References:
1707000- followed by two numbers; followed by -; followed by one letter.
Brand Names:
Tesla
Relevant Standard(s) /
Specification(s):
See Appendix 1
Verification Issuing Office Name
& Address:
Intertek Testing Services NA, Inc.
3933 US Route 11, Cortland, NY 13045 USA
Date of Tests:
9/15/2022 to 4/23/2024
Test Report Number(s): 104514208CRT-001, 104514208CRT-001RRF, 104514208CRT-001TRS,
104514208CRT-010, 104514208CRT-012
Additional information in Appendix.
Signature
Name: Mukund Rana
Position: Sr. Staff Engineer
Date: 10th May 2024
On the basis of the tests undertaken, the samples of the below product have been found to comply with the
requirements of the referenced standards at the time the tests were carried out. This verification is part of the full
test report and should be read in conjunction with it.
This Verification is for the exclusive use of Intertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms
and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this
Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material,
product or service must first be approved in writing by Intertek. The observations and test/inspection results referenced in this Verification are relevant only to the sample tested/inspected. This
Verification by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.
Intertek Page 2 of 8 GFT-OP-11a (22-August-2019)
Appendix 1: Relevant Standard(s)/Specification(s)
Inverters, Converters, Controllers and Interconnection System Equipment for use with Distributed Energy Resources
[UL 1741:2021 Ed.3]
Grid Support Utility Interactive Equipment - Supplement SA to UL 1741:2021 Ed.3 - Inverters, Converters, Controllers
and Interconnection System Equipment for use with Distributed Energy Resources [UL 1741:2021 Ed.3 (Supplement
SA)]
Grid Support Utility Interactive Inverters and Converters Based Upon IEEE 1547:2018 & IEEE 1547.1:2020 -
Supplement SB to UL 1741:2021 Ed.3 - Inverters, Converters, Controllers and Interconnection System Equipment for
use with Distributed Energy Resources [UL 1741:2021 Ed.3 (Supplement SB)]
Energy Storage Systems and Equipment [ANSI/UL 9540:2020 Ed.2+R:09Apr2021]
Photovoltaic (PV) DC Arc-Fault Circuit Protection [UL 1699B:2018 Ed.1+R:18May2021]
Software in Programmable Components [UL 1998:2013 Ed.3+R:24Sep2018]
Tests For Safety-related Controls Employing Solid-state Devices [UL 991:2004 Ed.3+R:09Jun2010]
Batteries for Use in Stationary, Vehicle Auxiliary Power and Light Electric Rail (LER) Applications [ANSI/UL 1973:2018
Ed.2]
IEEE 1547:2018 - IEEE Standard for Interconnection and Interoperability of Distributed Energy Resources with
Associated Electric Power Systems Interfaces
IEEE 1547a:2020 - IEEE Standard for Interconnection and Interoperability of Distributed Energy Resources with
Associated Electric Power Systems Interfaces
Amendment 1: To Provide More Flexibility for Adoption of Abnormal Operating Performance Category III
IEEE 1547.1:2020 - IEEE Standard Conformance Test Procedures for Equipment Interconnecting Distributed Energy
Resources with Electric Power Systems and Associated Interfaces
Source requirements document UL 1741 (SRD) v2.0 – HECO
Electric Rule No.21-2020 Generating Facility Interconnections
Default New England Bulk System Area Settings Requirement
PRC-024-3 Frequency and Voltage Protection Settings for Generating Resources
GOVERNMENT OF PUERTO RICO PUBLIC SERVICE REGULATORY BOARD PUERTO RICO ENERGY BUREAU, Generating
Facility and Microgrid Interconnection Regulation (“Regulation”), July 2021
Power Conversion Equipment [CSA C22.2#107.1:2016 Ed.4+U1]
Interconnection of Distributed Energy Resources and Electricity Supply Systems [CSA C22.3#9:2020 Ed.2]
Photovoltaic Rapid Shutdown Systems [CSA C22.2#330:2023 Ed.2]
Safety Functions Incorporating Electronic Technology [CSA C22.2#0.8:2019 Ed.4]
This Verification is for the exclusive use of Intertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms
and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this
Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material,
product or service must first be approved in writing by Intertek. The observations and test/inspection results referenced in this Verification are relevant only to the sample tested/inspected. This
Verification by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.
Intertek Page 3 of 8 GFT-OP-11a (22-August-2019)
Appendix 2: Ratings & Principle Characteristics:
➢ Ratings:
Models 1707000-xx-y
Rated AC Output Power (W) 11500, 10000, 7680, 5750
Rated AC Input Power (W) Charging 5000
Max. Cont. Output Power (W) 11500, 10000, 7680, 5750
Max. Continuous Output PV to AC
Power Off-Grid (W) 15400
Max. Cont. Input Power (W) Charging 5000
AC Input / Output Voltage
(VL-L) 240
AC Output Frequency
(Hz) 60
Max. Cont. Output Current (A) 48, 4 1.6, 32, 24
Max. Cont. Input Current (A) Charging 20.83
Apparent Power rating (VA) 11500, 10000, 7680, 5750
Apparent Power rating (VA) Charging 5000
Normal Category A, B
Abnormal Category II, III
➢ Communication Protocol: IEEE 2030.5 protocol
➢ PCH board MD5 Firmware checksum: c5773b136a9ef9be9057302a67258482
➢ TACO board MD5 Firmware checksum: dcq8OiBXbQWYnK9UhCAjvl02/py2MZymmwAQYOn8jSc=
➢ Grid Support Function Parameters:
Tesla used the parameters in the Result reporting form “104514208CRT-001RRF” during the testing of the grid
support functions according to UL1741 SB. The parameters that have “blank” as their value are not applicable.
➢ UL 1998 and CSA C22.2#0.8 Evaluation:
ECU / Board Rev Software version Checksum UL1998, CSA C22.2#0.8
Compliant*
Date of evaluation
HVP / -E V2 51705DB5 Yes Apr-19-2024
PWS / -3F V2 34204954 Yes Apr-19-2024
PWS / -1F V2 B3C1375B Yes Apr-19-2024
PWS / -D V2 43FEF523 Yes Apr-19-2024
*Note: Below safety functions were evaluated during the UL1998 and UL 991 evaluation.
• List of all UL1998 and UL 991 functions are as follow:
o Overcharge
o Over-discharge
o Over Temperature
o Over current
o Relay weld, Isolation Monitoring Interruption, PV RSD (UL 1741)
o AFCI (UL 1699B)
This Verification is for the exclusive use of Intertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms
and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this
Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material,
product or service must first be approved in writing by Intertek. The observations and test/inspection results referenced in this Verification are relevant only to the sample tested/inspected. This
Verification by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.
Intertek Page 4 of 8 GFT-OP-11a (22-August-2019)
Hi -MC
LR5-54H
390*1%0
• Suitable for distril
• Advanced module
module efficiency
• M10 Gallium -doped Wafer
• Globally validated
• High module qua[
25-year
\/
Materials and Pr(
30
30-year Warranty
Linear Power Ou
Complete System and
Product Certifications
I EC 61215, 1 EC 61730, U L 61730
IS09001:2015: ISO Quality Mana€
ISO 14001:2015: ISO Environment Management System
ISO45001: 2018: Occupational Health and Safety
I EC62941: Guideline for module design qualification and type. approval
'll
LONGI p C 'is C E
Hi -MOP]
CITY OF SANTA ANA
Planning and Building Agency
Approved
LR5-54HABB 390-,1
4OR PERMIT ISSUANCE
HALF -CELL .1
ster ID:
Additional Value
30 Year Power Warranty
100�
98 h
+2.75`�
91.24b
M.00% ��
ST78 __
4,95W
84.5°,0 +6.50%
e0:79e
17]2
�Qoo
1156
uni�; mm
:7 _5 20 25 30
Mechanical Parameters
Cell Orientation 108(6x18)
Junction Box IP68, three diodes
Output Cable 4nnnw, ±1200mm
---
-
lengthcanbecustomized
-_
Glass Dual glass, 2.0+1.6mm heat strengthened glass
- -
- ->
Frame Anodized aluminum alloyframe--
Weight 215kg
Dimension 1722x1134x30mm
Toi
w Wi tt +2mm
dtn zmm
Packaging 36pcsper pallet/ 216pcs per 20'GP/936pcsor792pcs(OnlyforUSA) per40'TIC
45
C
A -A B-B
Electrical Characteristics STC:AM1.5 1000W/m2 25°C
NOCT:AM1.5 80OW/m2 20°C lm/s rest uncertainty
for Pri+3w
Module Type LR5-54HABB-390M LR5-54HABB-395M
LR5-54HABB-400M LR5-54HABB-405M LR5-54HABB-410M LR5-54HABB-415M
Testing Condition
STC
NOCT STC
NOCT
STC NOCT STC NOCT
STC
NOCT
STC NOCT
Maximum Power(Pmax/W)
390
291.5 395
295.2
400 299.0 405 302.7
410
306.5
415 310.2
Open Circuit Voltage(Voc/V)
36.58
34.39 36.81
34.61
37.05 34.84 37.29 35.06
37.53
35.29
37.77 35.51.
Short Circuit Current(Isc/A)
13.57
10.95 13.65
11.01
13.72 11.07 13.79 11.13
13.87
11.19
13.94 11.25
Voltage at Maximum Power(Vni
30.47
28.43 30.70
28.64
30.94 28.86 31.18 29.09
31.42
29.31
31.66 29.54
Current at Maximum Power (I mp/A)
12.80
10.26 12.87
10.31
12.93 10.36 12.99 10,41
13.05
10.45
13.11 10.50
Module Efficiency(%)
20.0
20.2
20.5 20.7
21.0
21.3
Electrical characteristics with different rear side power gain (reference to 40OW front)
Pmax/W
Voe/V
Ise/A
VmpN Imp/A
Pmaxgain
420
37.05
14.41
30.94 13.58
5%
440
37.05
15.09
30.94 14.22
10%
460
37.15
15.78
31.04 14.87
15%
480
37.15
16.46
31.04 15.52
20%
500
37.15
17.15
31.04 16.16
25%
Operating Parameters
Operational Temperature
Power Output Tolerance
Vocand Ise Tolerance
Maximum System Voltage
Maximum Series Fuse Rating
-40°C -+85°C
0 -3%
-3%
DC1500V (I EC/UL)
30A
Mechanical Loading
Front Side Maximum Static Loading
Rear Side Maximum Static Loading
Hailstone Test
5400Pa.
241
25mm Hailstone at the speed of 23m/s
Protection class Class 11 Temperature Ratings (STC)
Bifaciality 70±5% Temperature Coefficient of Isc +0.050%/°C
Fire Rating
ILL Similar type 38TemperatureCoefficient of Voc-0165%/°C
IEC Class C Temperature Coefficient of Pmax-0.340°h/°C
'Reference Standard: UL61730 Second Edition, Dated October 28, 2022
Specifications included in this datasheet are
No.8369 Shangyuan Road, Xi an Economic And subject to change without notice. LONGi
LONG' Technological Development Zone, Van, Shaanxi, China. reserves the right of final interpretation.
Web: www.longi.com (20230112DraftV02) Only for North America
PAGE
REV: A 4/27/2026
JAMES POBOG
2306 W MANLY AVE, SANTA
ANA, CA, 92704
PROJECT NUMBER:
109R-306POBO2 PR-3005088446
SHEET
DESIGNER:
SREERAJ P R
CUSTOMER RESIDENCE:
TEL. (714) 788-0787
APN: 412-253-53
(415) 580-6920 ex3
PV-5.0
#ESTAMP#SSTAMP
2500 WHITE RD. SUITE A, IRVINE CA 92614
PHONE 805.540.7603
FAX 949.215.7778
CA CL #750184
GILBERT CORREIA, C10, C46
SIGNAGE
NOTES AND SPECIFICATIONS:
·SIGNS AND LABELS SHALL MEET THE REQUIREMENTS OF THE CEC 2025 ARTICLE
110.21(B), UNLESS SPECIFIC INSTRUCTIONS ARE REQUIRED BY SECTION 690, OR
IF REQUESTED BY THE LOCAL AHJ.
·SIGNS AND LABELS SHALL ADEQUATELY WARN OF HAZARDS USING EFFECTIVE
WORDS, COLORS AND SYMBOLS.
·LABELS SHALL BE PERMANENTLY AFFIXED TO THE EQUIPMENT OR WIRING
METHOD AND SHALL NOT BE HAND WRITTEN.
·LABEL SHALL BE OF SUFFICIENT DURABILITY TO WITHSTAND THE ENVIRONMENT
INVOLVED.
·SIGNS AND LABELS SHALL COMPLY WITH ANSI Z535.4-2011, PRODUCT SAFETY
SIGNS AND LABELS, UNLESS OTHERWISE SPECIFIED.
·DO NOT COVER EXISTING MANUFACTURER LABELS.
WARNING!
DO NOT RELOCATE THIS
OVERCURRENT DEVICE
LABEL LOCATION:
ADJACENT TO PV BREAKER AND ESS
OCPD (IF APPLICABLE).
PER CODE(S): CEC 2025: 705.12(B)(2)
SOLAR
ELECTRIC PV
PANELS
LABEL LOCATION:
ON OR NO MORE THAT 1 M (3 FT) FROM THE SERVICE
DISCONNECTING MEANS TO WHICH THE PV SYSTEMS
ARE CONNECTED.
TURN RAPID SHUTDOWN
SWITCH TO THE "OFF"
POSITION TO SHUT DOWN PV
SYSTEM AND REDUCE SHOCK
HAZARD IN THE ARRAY.
4"
3"
PER CODE(S): CEC 2025: 690.12(D)
ELECTRICAL SHOCK HAZARD
WARNING!
LABEL LOCATION:
INVERTER(S), AC/DC DISCONNECT(S),
AC COMBINER PANEL (IF APPLICABLE).
PER CODE(S): CEC 2025: 690.13(B),
705.20(7), 706.15(C)
LABEL LOCATION:
INSTALLED WITHIN 3' OF RAPID SHUT DOWN
SWITCH PER CODE(S): CEC 2025: 690.12(D)(2), IFC
2021: 1204.5.3
THIS EQUIPMENT FED BY
MULTIPLE SOURCES. TOTAL
RATING OF ALL OVERCURRENT
DEVICES EXCLUDING MAIN
SUPPLY OVERCURRENT DEVICE
SHALL NOT EXCEED AMPACITY OF
BUSBAR
WARNING!
LABEL LOCATION:
PV LOAD CENTER (IF APPLICABLE) AND
ANY PANEL THAT UTILIZES "THE SUM
OF BREAKERS RULE".
PER CODE(S): CEC 2025: 705.12 (B)(3)
INVERTER 1
PHOTOVOLTAIC DC DISCONNECT
MAXIMUM SYSTEM VOLTAGE:VDC550
LABEL LOCATION:
INVERTER(S), DC DISCONNECT(S).
PER CODE(S): CEC 2025: 690.7(D)
LABEL LOCATION:
INTERIOR AND EXTERIOR DC CONDUIT EVERY 10 FT,
AT EACH TURN, ABOVE AND BELOW PENETRATIONS,
ON EVERY JB/PULL BOX CONTAINING DC CIRCUITS.
PER CODE(S): CEC 2025: 690.31(D)(2)
WARNING!
SOURCES: UTILITY GRID,
BATTERY AND PV SOLAR
ELECTRIC SYSTEM
THREE POWER SUPPLY
LABEL LOCATION:
UTILITY SERVICE METER AND MAIN
SERVICE PANEL.
PER CODE(S): CEC 2025: 705.10, 705.30(C),
706.21(A)
INVERTER 1
LABEL LOCATION:
REQUIREMENT: UL 1741, SECTION 206.1 AND 206.4
LOCATION: MAIN PANEL
SIZE: 4.25" X 1.25"
PCS CONTROLLED CURRENT SETTING: 56 A
THE MAXIMUM OUTPUT CURRENT FROM THIS
SYSTEM IS CONTROLLED ELECTRONICALLY.
REFER TO THE MANUFACTURER'S
INSTRUCTIONS FOR MORE INFORMATION.
WARNING: THIS SENSOR IS PART
OF A POWER CONTROL SYSTEM.
DO NOT REMOVE. REPLACE ONLY
WITH THE SAME TYPE AND RATING.
WARNING: THIS SENSOR IS PART
OF A POWER CONTROL SYSTEM.
DO NOT REMOVE. REPLACE ONLY
WITH THE SAME TYPE AND RATING.
REQUIREMENT: UL 1741, SECTION 206.3
LOCATION: AROUND THE CT WIRE BY CLAMP
SIZE 4.25" X 0.75"
NOMINAL ESS VOLTAGE VAC
LABEL LOCATION:
ENERGY STORAGE SYSTEM
PER CODE(S): CEC 2025: 706.15(C)
120/240
ENERGY STORAGE SYSTEM DISCONNECT
ENERGY STORAGE SYSTEM
CAUTION!
LABEL LOCATION:
INVERTER(S), AC/DC DISCONNECT(S), AC COMBINER PANEL (IF APPLICABLE).
PER CODE(S): CEC 2025: 706.15(C)
PAGE
REV: A 4/27/2026
JAMES POBOG
2306 W MANLY AVE, SANTA
ANA, CA, 92704
PROJECT NUMBER:
109R-306POBO2 PR-3005088446
SHEET
DESIGNER:
SREERAJ P R
CUSTOMER RESIDENCE:
TEL. (714) 788-0787
APN: 412-253-53
(415) 580-6920 ex3
PV-5.1
#ESTAMP#SSTAMP
2500 WHITE RD. SUITE A, IRVINE CA 92614
PHONE 805.540.7603
FAX 949.215.7778
CA CL #750184
GILBERT CORREIA, C10, C46
SIGNAGE 2
SOLAR PANELS ON ROOF
CAUTION:
MULTIPLE SOURCES OF POWER
2306 W MANLY AVE, SANTA ANA, CA, 92704
MAIN SERVICE ENTRANCE
WITH TESLA BACKUP SWITCH
REMOTE DISCONNECT SWITCH(EXT)
INVERTER AND ENERGY
STORAGE(EXT)-PCS CONTROLLED(N)AC DISCONNECT (EXT)
(E)PV EQUIPMENT(N)LOAD CENTER(E)PV EQUIPMENTS
(N)EXPANSION PACK(EXT)
PV SYSTEM(S) ARE EQUIPPED WITH
RAPID SHUTDOWN DEVICE(S)
LABELING FORMAT
LABELS SHALL BE RED PLASTIC MATERIAL WITH ENGRAVED WHITE LETTERS
MADE OF DURABLE ADHESIVE, WEATHER RESISTANT MATERIAL SUITABLE FOR
THE ENVIRONMENT. LETTERS SHALL BE MINIMUM 3/8" IN SIZE.
PER CODE(S): NEC 2020 : 705.10, 710.10, CEC 2025: 705.10, 710.10
(E)PV ARRAY
This Verification is for the exclusive use of Intertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms
and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this
Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material,
product or service must first be approved in writing by Intertek. The observations and test/inspection results referenced in this Verification are relevant only to the sample tested/inspected. This
Verification by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.
Intertek Page 5 of 8 GFT-OP-11a (22-August-2019)
Appendix 3: List of Tested Grid protection / Support Function:
Table 3A: Test List -1
Grid protection / Support
Function Tested
Test Standards Sections and Source Requirement Documents
IEEE 1547-
2018
IEEE 1547.1-
2020
UL 1741SB -
2021 CA Rule 21:2020
UL 1741 SRD
V2.0
(HECO):2020
OPERATIONAL TEMPERATURE -- 5.3.3.1 SB4.3.5.3 -- Same as 1547-
2018
PROTECTION FROM
ELECTROMAGNETIC
INTERFERENCE (EMI) TEST
4.11.1 5.8.1 SB4.3.5.8.1 -- Same as 1547-
2018
SURGE WITHSTAND
PERFORMANCE TEST 4.11.2 5.8.2 SB4.3.5.8.2 -- Same as 1547-
2018
PARALLELING DEVICE 4.11.3 5.8.3 -- -- Same as 1547-
2018
OVERVOLTAGE TRIP 6.4.1 5.4.2 SB4.3.5.4.2 Electric Rule No.
21 Table Hh.1
Same as 1547-
2018
UNDERVOLTAGE TRIP 6.4.1 5.4.3 SB4.3.5.4.3 Electric Rule No.
21 Table Hh.1
Same as 1547-
2018
OVERFREQUENCY TRIP 6.5.1 5.5.1 & 5.5.2
SB4.3.5.5.1
&
SB4.3.5.5.2
Electric Rule No.
21 Table Hh.2
Same as 1547-
2018
UNDERFREQUENCY TRIP 6.5.1 5.5.1 & 5.5.2
SB4.3.5.5.1
&
SB4.3.5.5.2
Electric Rule No.
21 Table Hh.2
Same as 1547-
2018
LOW VOLTAGE RIDE-THROUGH 6.4.2.3 &
6.4.2.5 5.4.4 SB4.3.5.4.4 Electric Rule No.
21 Table Hh.1
Same as 1547-
2018
HIGH VOLTAGE RIDE-THROUGH 6.4.2.4 5.4.7 SB4.3.5.4.7 Electric Rule No.
21 Table Hh.1
Same as 1547-
2018
LOW FREQUENCY RIDE-THROUGH 6.5.2.3 5.5.3 SB4.3.5.5.3 Electric Rule No.
21 Table Hh.2
SRD-UL-1741-SA-
V2.0 (HECO) Part
II B
HIGH FREQUENCY RIDE-
THROUGH 6.5.2.4 5.5.4 SB4.3.5.5.4 Electric Rule No.
21 Table Hh.2
SRD-UL-1741-SA-
V2.0 (HECO) Part
II B
RATE OF CHANGE OF FREQUENCY 6.5.2.5 5.5.5 -- -- Same as 1547-
2018
ANTI-ISLANDING PROTECTION -
WITH GRID SUPPORT FUNCTIONS
ENABLED
8.1 5.10.2 SB4.3.5.10.2 Electric Rule No.
21 Hh.1a
According to UL
1741 SA-V2.0
(HECO)
TEST FOR VOLTAGE PHASE-ANGLE
CHANGE RIDE-THOUGH
(VARIATION 1)
6.5.2.6 5.5.6.1 SB4.3.5.5.6 -- Same as 1547-
2018
ENTER SERVICE 4.10 5.6 -- -- Same as 1547-
2018
SYNCHRONIZATION CONTROL
FUNCTION TEST FOR EQUIPMENT
WITH NO SYNCHRONIZING
DISABLE CAPABILITY (VARIATION
3)
6.3 5.7.4 -- -- Same as 1547-
2018
LIMITATION OF DC INJECTION
FOR INVERTERS 7.1 5.9 -- Electric Rule No.
21 Hh.2h
Same as 1547-
2018
OPEN PHASE 6.2.2 5.11 -- -- Same as 1547-
2018
CURRENT DISTORTION 7.3 5.12 -- Electric Rule No. Same as 1547-
This Verification is for the exclusive use of Intertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms
and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this
Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material,
product or service must first be approved in writing by Intertek. The observations and test/inspection results referenced in this Verification are relevant only to the sample tested/inspected. This
Verification by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.
Intertek Page 6 of 8 GFT-OP-11a (22-August-2019)
Grid protection / Support
Function Tested
Test Standards Sections and Source Requirement Documents
IEEE 1547-
2018
IEEE 1547.1-
2020
UL 1741SB -
2021 CA Rule 21:2020
UL 1741 SRD
V2.0
(HECO):2020
21 Hh.2g 2018
LIMIT ACTIVE POWER 4.6.2 5.13 -- Electric Rule No.
21 Hh.8
Same as 1547-
2018
CONSTANT POWER FACTOR 5.3.2 5.14.3 SB4.3.5.14.3 Electric Rule No.
21 Hh.2i
Same as 1547-
2018
VOLTAGE-REACTIVE POWER
(VOLT-VAR) MODE FIXED VREF 5.3.3 5.14.4 SB4.3.5.14.4 Electric Rule No.
21 Hh.2J
Same as 1547-
2018
VOLTAGE-REACTIVE POWER
(VOLT-VAR) MODE (VREF TEST) 5.3.3 5.14.5 SB4.3.5.14.5 -- Same as 1547-
2018
ACTIVE POWER-REACTIVE POWER
MODE (WATT-VAR) 5.3.4 5.14.7 SB4.3.5.14.7 -- Same as 1547-
2018
CONSTANT REACTIVE POWER
(VAR) MODE 5.3.5 5.14.8 SB4.3.5.14.8 -- Same as 1547-
2018
VOLTAGE-ACTIVE POWER (VOLT-
WATT) MODE 5.4 5.14.9 SB4.3.5.14.9 Electric Rule No.
21 Hh.2.m
Same as 1547-
2018
TEST FOR FREQUENCY -DROOP
(FREQUENCY-POWER OR
FREQUENCY-WATT) CAPABILITY —
ABOVE NOMINAL FREQUENCY
6.5.2.7 5.15.2 SB4.3.5.15.2 Electric Rule No.
21 Hh.2.l
SRD-UL-1741-SA-
V2.0 (HECO) Part
II C
TEST FOR FREQUENCY -DROOP
(FREQUENCY-POWER OR
FREQUENCY-WATT) CAPABILITY —
BELOW NOMINAL FREQUENCY
6.5.2.7 5.15.3 SB4.3.5.15.3 Electric Rule No.
21 Hh.2.l
SRD-UL-1741-SA-
V2.0 (HECO) Part
II C
PRIORITIZATION OF DER
RESPONSES 4.7 5.16 SB4.3.5.16 -- Same as 1547-
2018
LOAD REJECTION OVERVOLTAGE
(LROV) 7.4 5.17.2 SB4.3.5.17.2 -- Same as 1547-
2018
FAULT CURRENT TESTS FOR
INVERTERS 6.2.1 5.18.1 -- -- Same as 1547-
2018
PERSISTENCE OF DER PARAMETER
SETTINGS -- 5.19 -- -- Same as 1547-
2018
NORMAL RAMP RATE -- -- -- Electric Rule No.
21 Hh.2k --
NAMEPLATE DATA TEST 10.3 6.4 -- -- Same as 1547-
2018
MONITORING INFORMATION
TEST 10.5 6.6 SB4.3.6.6 -- Same as 1547-
2018
MANAGEMENT INFORMATION
TEST 10.6 6.7 SB4.3.6.7 -- Same as 1547-
2018
CITY OF SANTA ANA
Planning and Building Agency
POWERWALL
Backup Gateway
The Backup Gateway for Tesla Powerwall provides energy management
and monitoring for solar self -consumption, time -based control, and
backup.
The Backup Gateway controls connection to the grid, automatically
detecting outages and providing a seamless transition to backup
power. When equipped with a circuit breaker, the Backup Gateway can
be installed at the service entrance.
The Backup Gateway communicates directly with Powerwall, allowing
you to monitor energy use and manage backup energy reserves from
any mobile device with the Tesla app.
PERFORMANCE SPECIFICATIONS
AC Voltage (Nominal)
230 V, 120/240 V
Feed -In Type
Single & Split Phase
Grid Frequency
50 and 60 Hz
Disconnect Current
200 A
Maximum Input Short Circuit Current
10 kA
Overcurrent Protection Device'
100-200 A: Service Entrance Rated
Overvoltage Category
Category IV
AC Meter
Revenue grade (+/- 1 %)
Connectivity
Ethernet, Cellular (3G)2, Wi-Fi
User Interface
Tesla App
Operating Modes
Support for solar self -consumption,
time -based control, and backup
Backup Operation
Automatic disconnect for seamless
backup transition
Modularity
Supports up to 10 AC -coupled
Powerwalls
Warranty
10 years
Circrnt oreaker ecuired for nstallatio^ at 3eivice
entrance.
'CellLlaf --onnecuvity Sublet t to
se-v C2 ccve'a3E find ai0l:al sueriq]' ,
COMPLIANCE INFORMATION
Certifications
UL 1642, UL 1741, IEC 62109-1,
CSA C22.2.107.1
Grid Connection
Worldwide Compatibility
Emissions
FCC Part 15 Class B, ICES 003,
IEC 61000-6-3. EN 55024,
EN 301489-1, EN 301489-7,
EN 301489-17
Environmental
RoHS Directive 2011/65/EU,
WEEE Directive 2012/19/EU,
Battery Directive 2006/66/EC
REACH Regulation
Seismic
AC156, IEEE 693-2005 (high)
MECHANICAL SPECIFICATIONS
Dimensions 740 mm x 378 min x 129 mm
(29.1 inx149inx51 in)
Weight 16.4 kg (36 Ibs)
Mounting options Wall mount
378 mm 129 mm
(14.9 in) (5.1 in)
740 mm
(29.1 in)
ENVIRONMENTAL SPECIFICATIONS
Operating Temperature
Operating Humidity (RH)
Maximurn Elevation
Environment
Enclosure Type
Ingress Rating
-20'C to 50'C (-4`F to 122°F)
Up to 100%, condensing
3000 m (9843 ft)
Indoor and outdoor rated
NEMA 3R
IP44
.4
Approved
FOR PERMIT ISSUANCE
Master ID:
Date:
TSSLn
Powerwall 3
Power Everything
2024
—
Powerwall 3 is a fully integrated solar and battery system, designed to accelerate the transition to sustainable energy. Customers
can receive whole home backup, cost savings, and energy independence by producing and consuming their own energy while
participating in grid services. Once installed, customers can manage their system using the Tesla App to customize system
behavior to meet their energy goals.
Powerwall 3 achieves this by supporting up to 20 kW DC of solar and providing 11.5 kW AC of continuous power per unit. It has
the ability to start heavy loads up to 185 A LRA, meaning a single unit can support the power needs of most homes. Powerwall 3
is designed for mass production,fast and efcient installations,easy system expansion,and simple connection to any electrical
service.
22024Powerwall 3 Datasheet
Solar Technical
Specications
Maximum Solar STC Input 20 kW
Withstand Voltage 600 V DC
PV DC Input Voltage Range 60 — 550 V DC
PV DC MPPT Voltage Range 60 — 480 V DC
MPPTs 6
Maximum Current per MPPT (Imp)13 A 5
Maximum Short Circuit Current per MPPT (Isc)15 A 5
Powerwall 3 Technical Specifications
1 Typical solar shifting use case.
2 Values provided for 25°C (77°F), at beginning of life. 3.3 kW charge/discharge power.
3 Tested using CEC weighted efciency methodology.
4 The customer is expected to provide internet connectivity for Powerwall 3;cellular should not be used as the primary mode of
connectivity. Cellular connectivity subject to network operator service coverage and signal strength.
5 Where the DC input current exceeds the MPPT rating,a jumper can be used to combine two MPPTs into a single input to
intake DC current up to 26 A IMP / 30 A ISC.
Battery Technical
Specications
Nominal Battery Energy 13.5 kWh AC 2
Maximum Continuous Discharge Power 11.5 kW AC
Maximum Continuous Charge Power 5 kW AC
Output Power Factor Rating 0 -1 (Grid Code congurable)
Maximum Continuous Current 48 A
Maximum Output Fault Current 10 kA
Load Start Capability (1 s)185 A LRA
Power Scalability Up to 4 Powerwall 3 units supported
System Technical
Specications
Model Number 1707000-xx-y
Nominal Grid Voltage (Input &Output)120/240 VAC
Grid Type Split phase
Frequency 60 Hz
Overcurrent Protection Device 60 A
Solar to Battery to Home/Grid Efciency 89% 1,2
Solar to Home/Grid Efciency 97.5% 3
Supported Islanding Devices Gateway 3, Backup Switch, Backup Gateway 2
Connectivity Wi-Fi (2.4 and 5 GHz), Dual-port switched Ethernet,
Cellular (LTE/4G 4)
Hardware Interface Dry contact relay,Rapid Shutdown (RSD)certied switch
and 2-pin connector, RS-485 for meters
AC Metering Revenue Grade (+/- 0.5%)
Protections Integrated arc fault circuit interrupter (AFCI), Isolation
Monitor Interrupter (IMI),PV Rapid Shutdown (RSD)using
Tesla Mid-Circuit Interrupters
Customer Interface Tesla Mobile App
Warranty 10 years
Hi -MC
LR5-54H
39041%0
- Suitable for distril
• Advanced module
module efficiency
• M10 Gallium -doped Wafer
• Globallyvalidatec
• High module clual
25-y\/ earWa rraMaterials andnd Pr( Pn
30 3 0-yea r Wa rra n t}
Linear Power Ou
Complete System and
Product Certifications
I EC 61215, 1 EC 61730, U L 61730
IS09001:2015: ISO Qua lity Manages .,.,,
IS014001:2015: ISO Environment Management System
ISO45001: 2018: Occupational Health and Safety
IEC62941: Guideline for module design qualification and type approval
■
LONGI � c I'llC E
01W
•5
21.3% 0-
MAX MODULE Pf
EFFICIENCY TO
Additional
30-Year Power Warranty
100%
98%
912% +2.75%
87.79E
84.5%
+6.50%
80.A
1 _;] 15 20 25 30
Mechanical Parameters
Cell Onentaticn 108(6x 18)
Junction Box IP68, three diodes
Output Cable 4mm2,±1200mm
length can be customized
CITY OF SANTA ANA
Planning and BLlilding Agency
Approved
LR5-54HABB 390-41 MOR PERMIT ISSUANCE
ster ID:
9
Glass Dual glass, 2.0+1.6mm heat strengthened glass
Frame Anodized aluminum alloy frame - -
Weight 22.5kg ole ance
Dimension 1722x1134x30mm zr„m W,X: e
w�dm_2mm L�
Packaging 36pcs per pallet /216pcs per20'GP/936pcs or 792pcs(Only for USA) per40' HC ltsl
c A -A B-B
Electrical Characteristics STC:AM1.5 1000W/m= 25°C NOCT:AM1.5 80OW/m2 20°C 1m/s Testuncertaintyfor Pmax:+3.4;
Module Type LR5-54HABB-390M LR5-54HABB-395M LR5-54HABB-400M LR5-54HABB-005M LR5-54HABB-410M LR5-54HABB-415M
Testing Condition
STC
NOCT STC NOCT
STC NOCT STC NOCT
STC NOCT STC NOCT
Maximum Power(Pmax/Y4)
390
291.5 395 295.2
400 299.0. 405 302.7
410 306.5 415 310.2
Open Circuit Voltage (Voc/V)
36.53
34.39 36.81 34.61
37.05 34.84 37.29 35.06
37.53 35.29 37.77 35.51
Short Circuit Current(Isc/A)
13.57
10.95 13.65 11.01
13.72 11.07 13.79 11.13
13.87 11.19 13.94 11.25
Voltage at Maximum Power(Vmp/V)
30.47
28.43 30.70 28.64
30.94 28.86 31.18 29.09
31.42 29.31 31.66 29.54
Current at Maximum Power(Imp/A)
12.80
10.26 12.87 10.31
12.93 10.36 12.99 10.41
13.05 10.45 13.11 10.50
Module Efficiency(%)
20.0 20.2
20.5 20.7
21.0 21.3
Electrical characteristics with different rear side power gain (reference to
40OW front)
Pmax/W
VOC/V
Isc/A
Vm pN Imp/A
Pmax gain
420
37.05
14A1
30.94 13.58
5%
440
37.05
15.09
30.94 14.22
10%
460
37.15
15,78
31.04 14.87
15%
480
37.15
16.46
31.04 15.52
20%.
500
37.15
17.15
31.04 16.16
25%
Operating Parameters
Mechanical Loading
Operational Temperature
-40°C -+85°C
Front Side Maximum Static Loading
540OPa
Power Output Tolerance
0 - 3%
Rear Side Maximum Static Loading
24001ea
Voc and Ise Tolerance
±3%
Hailstone Test
25mm Hailstone at the speed of 23m/s
Maximum System Voltage
DC1500V(IEC/UL)
Maximum Series Fuse Rating
30A
Nominal Operating Cell Temperature
45±2°C
Protection Class
Class a
Temperature Ratings (STC)
eifaciality
70±5%
Temperature Coefficient of Isc
+0.050%/-C
UL Similar type 38
Temperature Coefficient of Voc
-0.265%/°C
Fire Rating
IECClass C
Temperature Coefficient of Pmax
-0.340%/°C
-Reference Standard: UL617305econd Editfon, Dated October 28, 2022
■
Specifications included in this datasheet are
No.8369 Shangyuan Road, Van
Economic And
subject to change without notice. LONG!
IANG I
Technological Development Zone, Van, Shaanxi, China.
reserves the right of final interpretation.
Web: www.longl.com
(20230112DraftV02) Only for North America
!"#!$
%$&
'
(
)( *+ ,-
((* ,
. ) ./
( *
00+&1&2!!
%
.
.3(
4
/
*4
.
.3 #!5$
/
. (
/(
671
.(
.3 %$&
..
*8
./ )(
..
4
*.
((
(.
%. .3*8
/
-)
/(
(
(..
. 3
*
.3
.
( *
"(
3
.3 !"$
9
$ :222$ &
(-.-
$ : 222$ &88
-8(
-
.
*
:;#2615--<72715.=
3 2#!5--<;2#&5.=
8 ;1215--<&2715.=
3
..3 >
&2;152-<&15()/2.=!2!!?!2!:5.@<2!6?12#5--@=$ : 222$ :!=
&2;152-<&15()/2.=$ : 222$ :!=
12!652-< 15()/2.=!2!:5.@<62&75--@=$ 6=
12!652-< 15()/2.=!2!?!2!&5.@<:2&?:2:5--@=$ #222$ =
12#152-<1!5()/2.=!2! 5.@<#2#75--@=$ &=
.3
. 88.3
(
3*!!:!#AB %$&B&!!!$
.
(
:$
(
-
+
-
.
.
.
.
.
)
/
.
.
)
/
-
.
.
3
)
(
*
(
)
(
*
/
8
/
8
/
8
8
(
.
Feb 3, 2020
:
!!761;!: ;: ;:
,
3
4
3 < ) =2::5,3< 2#15()<==
.
)( *C
. */3.%D
//
.
)( *
.
)(
//
.
--8
(/.
88 .#1 $ + 8
.
E8
*
-
( .(.3+
.(
-8. 4
,.4.
/
(/.
.3
.A
8 '
-2 -
./-
.3
44428#14
..3 2
23'
$
3(
. $
(
.
$ /
/"C
'
-8(
.
(
.
E
'*-
(/
C
%
*/
C
E
-8 ../-
.C
.
3(
. .
(
.
'
.
(
.< / .
(
3
( 8
=
.'.-
.
( (
.'.-
.
(/(
(
*/(
.
/ 8
/
*(.38
.
.
(4
. *
. *:6-.
32024Powerwall 3 Datasheet
Mechanical
Specications
Dimensions 1099 x 609 x 193 mm (43.25 x 24 x 7.6 in)
Weight 130 kg (287 lb)
Mounting Options Floor or wall mount
Powerwall 3 Technical Specifications
Environmental
Specications
Operating Temperature –20°C to 50°C (–4°F to 122°F) 6
Operating Humidity (RH)Up to 100%, condensing
Storage Temperature –20°C to 30°C (–4°F to 86°F), up to 95% RH, non-
condensing, State of Energy (SOE): 25% initial
Maximum Elevation 3000 m (9843 ft)
Environment Indoor and outdoor rated
Enclosure Rating NEMA 3R
Ingress Rating IP67 (Battery & Power Electronics)
IP45 (Wiring Compartment)
Pollution Rating PD3
Operating Noise @ 1 m < 50 db(A) typical
<62 db(A)maximum
Compliance
Information
Certications UL 1642, UL 1699B, UL 1741, UL 1741 SA, UL 1741 SB, UL
1741 PCS, UL 3741, UL 1973, UL 1998, UL 9540, IEEE 1547-
2018, IEEE 1547.1, UN 38.3
Grid Connection United States
Emissions FCC Part 15 Class B
Environmental RoHS Directive 2011/65/EU
Seismic AC156, IEEE 693-2005 (high)
Fire Testing Meets the unit level performance criteria
of UL 9540A
6 Performance may be de-rated at operating temperatures above 40°C (104°F).
609 mm 193
mm
1099 mm
42024Powerwall 3 Datasheet
Electrical
Specications
Model MCI-1 MCI-2
Nominal Input DC Current Rating (IMP)13 A 13 A
Maximum Input Short Circuit Current (ISC)19 A 17 A
Maximum System Voltage (PVHCS)600 V DC 1000 V DC 7
Solar Shutdown Device Technical Specifications
Environmental
Specications
Operating Temperature -40°C to 50°C
(-40°F to 122°F)
-45°C to 70°C
(-49°F to 158°F)
Storage Temperature –30°C to 70°C
(–22°F to 158°F)
–30°C to 70°C
(–22°F to 158°F)
Enclosure Rating NEMA 4X /IP65 NEMA 4X /IP65
RSD Module
Performance
Maximum Number of Devices per String 5 5
Control Power Line Excitation Power Line Excitation
Passive State Normally Open Normally Open
Maximum Power Consumption 7 W 7 W
Warranty 25 years 25 years
—
The Solar Shutdown Device is a Mid-Circuit Interrupter (MCI)and is part of the PV system rapid shutdown (RSD)function in
accordance with Article 690 of the applicable NEC. When paired with Powerwall 3, solar array shutdown is initiated by any loss
of AC power.
Mechanical
Specications
Electrical Connections MC4 Connector MC4 Connector
Housing Plastic Plastic
Dimensions 125 x 150 x 22 mm
(5 x 6 x 1 in)
173 x 45 x 22 mm
(6.8 x 1.8 x 1 in)
Weight 350 g (0.77 lb) 120 g (0.26 lb)
Mounting Options ZEP Home Run Clip
M4 Screw (#10)
M8 Bolt (5/16")
Nail / Wood screw
Wire Clip
Compliance
Information
Certications UL 1741 PVRSE, UL 3741,
PVRSA (Photovoltaic Rapid Shutdown Array)
RSD Initiation Method External System Shutdown Switch or
Powerwall 3 Enable Switch
7 Maximum System Voltage is limited by Powerwall to 600 V DC.
UL 3741 PV Hazard Control
(and PVRSA)Compatibility See Powerwall 3 Installation Manual
52024Powerwall 3 Datasheet
Gateway 3
8 Only Eaton CSR or BWH main breakers are 25 kA rated.
Performance
Specications
Model Number 1841000-01-y
Nominal Grid Voltage 120/240 V AC
Grid Conguration Split phase
Grid Frequency 60 Hz
Continuous Current
Rating
200 A
Maximum Supply Short
Circuit Current
22 kA with Square D or
Eaton main breaker
25 kA with Eaton main
breaker 8
IEC Protective Class Class I
Overvoltage Category Category IV
Mechanical
Specications
Dimensions 660 x 411 x 149 mm
(26 x 16 x 6 in)
Weight 16.3 kg (36 lb)
Mounting options Wall mount
Environmental
Specications
Operating Temperature –20°C to 50°C (–4°F to 122°F)
Operating Humidity (RH)Up to 100%, condensing
Maximum Elevation 3000 m (9843 ft)
Environment Indoor and outdoor rated
Enclosure Type NEMA 3R
Compliance
Information
Certications UL 67, UL 869A, UL 916, UL 1741 PCS,
CSA 22.2 107.1, CSA 22.2 29
Emissions FCC Part 15, ICES 003
—
Tesla Gateway 3 controls connection to the grid in a Powerwall system, automatically detecting outages and providing seamless
transition to backup power. It provides energy monitoring that is used by Powerwall for solar self-consumption, time-based
control, and backup operation.
411 mm
660
mm
149
mm
AC Meter Revenue accurate (+/- 0.5%)
Communication CAN
User Interface Tesla App
Backup Transition Automatic disconnect for
seamless backup
Overcurrent
Protection Device
100–200 A
Service entrance rated
Eaton CSR, BWH, or BW, or
Square D QOM breakers
Internal Panelboard 200 A
8-space/16 circuit breakers
Eaton BR, Siemens QP, or
Square D HOM breakers rated
to 10–125A
Warranty 10 years
62024Powerwall 3 Datasheet
Backup Switch
9 Breaker maximum supply short circuit current rating must be equal to or greater than the available fault current.
Performance
Specications
Model Number 1624171-xx-y
Continuous Load Rating 200 A, 120/240 V split phase
Maximum Supply Short Circuit Current 22 kA with breaker 9
Communication CAN
AC Meter Revenue accurate (+/- 0.5%)
Expected Service Life 21 years
Warranty 10 years
Mechanical
Specications
Dimensions 176 x 205 x 74 mm (6.9 x 8.1 x 2.9 in)
Weight 2.8 lb
Meter and Socket Compatibility ANSI Type 2S, ringless or ring type
External Service Interface Contactor manual override 10
Reset button
Conduit Compatibility 1/2-inch NPT
Environmental
Specications
Operating Temperature –40°C to 50°C (–40°F to 122°F)
Storage Temperature –40°C to 85°C (–40°F to 185°F)
Enclosure Rating NEMA 3R
Pollution Rating PD3
Compliance
Information
Safety Standards USA: UL 414, UL 414 SB, UL 2735, UL 916, CA Prop 65
Emissions FCC, ICES
10 Manually overrides the contactor position during a service event.
—
The Tesla Backup Switch controls connection to the grid in a Powerwall system, and can be easily installed behind the utility
meter or in a standalone meter panel downstream of the utility meter.
The Backup Switch automatically detects grid outages, providing a seamless transition to backup power. It communicates
directly with Powerwall, allowing home energy usage monitoring from any mobile device with the Tesla app.
204.86
74
176 mm
205 mm
74 mm
72024Powerwall 3 Datasheet
Backup Gateway 2
Performance
Specications
Model Number 1232100-xx-y
AC Voltage (Nominal)120/240 V
Feed-in Type Split phase
Grid Frequency 60 Hz
Current Rating 200 A
Maximum Supply Short
Circuit Current
10 kA 11
Overcurrent Protection
Device
100 - 200 A, Service
entrance rated 9
Overvoltage Category Category IV
Internal Primary
AC Meter
Revenue accurate
(+/- 0.2%)
Internal Auxiliary
AC Meter
Revenue accurate
(+/- 2%)
Primary Connectivity Ethernet, Wi-Fi
Secondary Connectivity Cellular (3G, LTE/4G) 12
Mechanical
Specications
Dimensions 660 x 411 x 149 mm
(26 x 16 x 6 in)
Weight 20.4 kg (45 lb)
Mounting options Wall mount,
Semi-Bush mount
Environmental
Specications
Operating Temperature –20°C to 50°C (–4°F to 122°F)
Operating Humidity (RH)Up to 100%, condensing
Maximum Elevation 3000 m (9843 ft)
Environment Indoor and outdoor rated
Enclosure Type NEMA 3R
Compliance
Information
Certications UL 67, UL 869A, UL 916, UL 1741 PCS,
CSA 22.2 0.19, CSA 22.2 205
Emissions FCC Part 15, ICES 003
411 mm
660 mm
149
mm
11 When protected by Class J fuses, Backup Gateway 2 is
suitable for use in circuits capable of delivering not more
than 22kA symmetrical amperes.
12 Cellular connectivity subject to network operator service
coverage and signal strength.
—
Backup Gateway 2 controls connection to the grid when paired with Powerwall 3, automatically detecting outages and providing
seamless transition to backup power. Backup Gateway 2 also provides energy metering for solar self-consumption, time-based
control, and backup operation.
In this system conguration,Powerwall 3 acts as the Site Controller,with the Backup Gateway 2 Site Controller disabled.
User Interface Tesla App
Operating Modes Support for solar self-
consumption, time-based
control, and backup
Backup Transition Automatic disconnect for
seamless backup
Modularity Supports up to 10 AC-
coupled Powerwalls
Optional Internal
Panelboard
200 A 6-space / 12 circuit
breakers
Siemens QP or Square D
HOM breakers rated 10 -
80A or Eaton BR breakers
rated 10 - 125A
Warranty 10 years
82024Powerwall 3 Datasheet
Powerwall 3 Example System Configurations
Powerwall 3 with Backup Switch
Whole Home Backup
Powerwall 3 with Gateway 3
Whole Home Backup
Powerwall 3 with Backup Gateway 2
Partial Home Backup
This Verification is for the exclusive use of Intertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms
and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this
Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material,
product or service must first be approved in writing by Intertek. The observations and test/inspection results referenced in this Verification are relevant only to the sample tested/inspected. This
Verification by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.
Intertek Page 7 of 8 GFT-OP-11a (22-August-2019)
Table 3B: Test List -2
Test Description
CSA
C22.2#107.1:2016
Ed. 4 CSA C22.3#9:2020 Ed 2
Screw Tightening Torque Test 3.6.3 --
Impedance Test 105.1/10.5.2 --
Continuity Test 4.1 --
Output Power Factor 4.2 --
Voltage Harmonics for stand alone 15.3.2.1 --
Frequency 10.5.4 --
Stand-alone inverter dc output short-circuits current contribution 10.5.5 --
Normal ramp rate -- 7.2.3.4.2 / 8.3.12.2.3
Flicker -- 7.2.2 / 8.3.13
Test for constant reactive power (var) mode 7.2.3.3.3 / 8.3.12.2.2
This Verification is for the exclusive use of Intertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms
and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this
Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material,
product or service must first be approved in writing by Intertek. The observations and test/inspection results referenced in this Verification are relevant only to the sample tested/inspected. This
Verification by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.
Intertek Page 8 of 8 GFT-OP-11a (22-August-2019)
Appendix 4: Revision Summary
Date /
Project Engineer Comments
15-Feb-2023 Dipesh Patel Original issue date
8-Mar-2023 /
G104200718
Dipesh Patel Added UL 1699B, UL 1998 and UL 991 standards
24-Mar-2023/
G104200718
Dipesh Patel Added UL 1973 standard.
Added normal and abnormal category in ratings table.
18-Apr-2023 /
G104200718
Dipesh Patel Added additional factory settable nameplate ratings rated output active
power (W): 9600, 7680, 5750; Max. Continuous output power (W):
9600, 7680, 5750; Max. Cont. Output Current (A): 40, 32, 24; Apparent
Power rating (VA): 9600, 7680, 5750
Added Puerto Rico Interconnection regulation as it refers to UL 1741
and IEEE 1547-2018.
1-May-2024 /
G104514208
Mukund Rana
A) Added standards.
Power Conversion Equipment [CSA C22.2#107.1:2016 Ed.4+U1]
Interconnection of Distributed Energy Resources and Electricity Supply
Systems [CSA C22.3#9:2020 Ed.2]
Photovoltaic Rapid Shutdown Systems [CSA C22.2#330:2023 Ed.2]
Interconnection of Distributed Energy Resources and Electricity Supply
Systems [CSA C22.3#9:2020 Ed.2]
B) Update CSA C22.2#0.8 standard
C) added Table 3B: Test List -2
Rev: 8/29/19
SOL-01 CBC 2016
Solar Photovoltaic (PV) Checklist for Detached SINGLE FAMILY RESIDENCES Only
Instructions: The licensed contractor of record shall complete all sections, answer the ten questions and
sign the certification section below. A copy of this form shall be attached to each of TWO sets of plans, of
minimum 11” x 17” size. If answering NO to any of the questions, plan check shall be required.
Project Address:
Contractor Company Name:
Contractor License Number:
YES NO Are the following applicable to the proposed project?
1. Will the PV system layout provide the required three-foot wide clear access pathways
per Section 605.11 of the California Fire Code, and is this shown on the roof plan?
2. Will the PV system be installed on a roof having only one roofing layer with no
overlays?
3. Will the PV array be flush mounted to the existing roof so that the plane of the
modules (panels) are parallel to the plane of the roof?
4. Will the PV system weigh maximum 4 pounds per square feet or less?
5. Will the PV system be installed where the modules do not overhang any roof edges
(such as eaves, gabled ends, ridges and hips)?
6. Will the PV system be installed with a space of 2” minimum to 10” maximum between
the underside of modules and the surface of the roof?
7. Will the PV system be installed without using any ballast system or counter-weight
system?
8. Will the anchors be installed with a maximum horizontal anchor spacing of 6 feet
and is this maximum horizontal spacing shown on the plans?
9. Will the minimum 5/16” lag screws be installed with a minimum of 2-1/2 inch
embedment into roof rafters (with pre-drilled holes) and is this minimum embedment
shown on the plans?
10. Are ALL the structural pages of the plans stamped and signed by a California
licensed professional engineer? (including project specific site plan, PV layout,
anchorage spacing, anchorage details and manufacturer’s PV support information.)
I certify under penalty of perjury under the laws of the State of California that the above is true:
Print Name: Signature:
Phone Number: Date:
Email Address:
Planning & Building Agency
Building Safety Division
20 Civic Center Plaza
P.O. Box 1988 (M-19)
Santa Ana, CA 92702
(714) 647-5800
www.santa-ana.org
RESIDENTIAL
PHOTOVOLTAIC
CHECKLIST
caitlyn hernandez
3854005019
oc_permits@sunrun.com
Astra v.2.200
4/28/2026 02:11 AM CAT 1, EOSS
#AStamp
Subject: Structural Certification for Proposed Residential Solar Installation.
Job Number: 109R-306POBO2; Rev A
Client: JAMES POBOG
Address: 2306 W Manly Ave, Santa Ana, CA 92704
Attn: To Whom It May Concern Signed on: 4/28/2026
A Sunrun representative has gathered site information on this structure in preparation for this permit application. A structural load evaluation
has been completed which compares the loads before and after the panel installation. For this structure, the calculated maximum roof load
after PV panel installation is less than the gravity and lateral load analysis triggers as set forth in the IEBC.
Based on an exterior inspection, this structure is performing adequately under the current loading. Prior to installation of the solar PV system,
a Sunrun representative will confirm that the attic roof framing has no unsafe or dangerous conditions present. Any localized items requiring
repair will be addressed as a part of the installation by the installing contractor and prior to installation.
Structural evaluation of the loading is based on the applicable design criteria listed below.
Design Criteria:
• 2025 CBC/CEBC, 7-22 ASCE & 2024 NDS
• Basic (Category II) Wind Speed V=95 mph, Exposure B
• Ground Snow Load = 3 psf
Based on this evaluation, I certify that the alteration to the existing structure by installation of the PV system meets the requirements of the
applicable existing building code provisions adopted/referenced above. Additionally, the PV module assembly and hardware supporting it have
been designed according to manufacturer's specifications per the loading criteria referenced above.
Installer shall inspect the existing roof framing to verify it is in suitable condition and does not exhibit signs of damage which may diminish the
capacity of its members or connections. If damage exists, the installer shall notify the engineer of record prior for guidance to proceeding with
installation.
Results Summary (Hardware Check Includes Uplift Check on Attachments/Fastener, Structure Check Considers Main Structure)
AR-01
Orientation Attachment Spacing/Cantilever Configuration Max DCR Result
Landscape 58 / 6 Staggered 36%Pass
Portrait 58 / 6 Staggered 31%Pass
Roofing Material Pitch Structure Check
Comp Shingle 18°Pass
AR-02
Orientation Attachment Spacing/Cantilever Configuration Max DCR Result
Landscape 58 / 6 Staggered 36%Pass
Portrait 58 / 6 Staggered 31%Pass
Roofing Material Pitch Structure Check
Comp Shingle 18°Pass
225 Bush St. Suite 1400 San Francisco, CA 94104
Exp. 12/31/2026
Digitally Signed On: 04/28/2026
Seismic Considerations: 10% Lateral Loading Increase Check
Seismic Design Criteria (per USGS)
Latitude Longitude Soil Site Class Ss S1 SDC
33.640302 -117.769442 D 1.237 0.443 D
Site Conditions
Module Type:LONGi Green Energy Technology Co Ltd: LR5-54HPB-410M-CYPRESSTotal Mods:8 Sum of Roof Areas w/ PV:2704
Load Information Area Dead Load Total Weight
Existing Roof 2704 sq ft 10 psf 27040 lb
Ceiling 2704 sq ft 5 psf 13520 lb
Interior Walls (Top Half)832 sq ft 5 psf 4160 lb
Exterior Walls (Top Half)832 sq ft 9 psf 7072 lb
System Weight PV 144 sq ft 3 psf 432 lb
Lateral Loading 10% Check (2018 IEBC Section 503.4)
Net Weight of PV System Net Weight of Roof % Increase of LFRS Final Result
432 lb 51792 lb 0.83%Pass
AR-01
Roofing Material Roof Pitch Hardware Results Structural Results
Comp Shingle 18°Pass Pass
Hardware Calculations
Attachment Information
Attachment:UltraFoot, Anchor Uplift Force: 0.6(p - (3psf x cos(pitch))) x trib area =133 lb Uplift Capacity: 375 lb a = 5.2 ft
Wind Design Criteria (Partially/Fully Enclosed Method, ASCE 7-22)
Basic Wind Speed V 95 mph Wind Speed - Category II
Wind Pressure Exposure Kz 0.67 Table 26.10-1
Topographic Factor Kzt 1.0 Figure 26.8-1
Wind Directionality Factor Kd 0.85 Table 26.6-1
Ground Elevation Factor Ke 1.00 Section 26.9
Velocity Pressure qh = 0.00256 x Kz x Kzt x Kd x Ke x V²13.14 psf Equation 26.10-1
Solar Adjustment Factors γe (Port/Land) =1.2 γa =0.535 Figure 29.4-7
Wind Pressures Zone 1 (up)Zone 2 (up)Zone 3 (up)Down
Ext Pressure Coefficient GCp -1.67 -2.28 -3.02 0.57 Figures 30.3-2(A-H)
Ultimate Design Wind Pressure p = qh x GCp x γe x γa -16.00 psf -16.00 psf -18.07 psf 16.00 psf Equation 29.4-7
Mod Orientation X-Spacing Cantilever Trib Area Demand DCR Final Result
Landscape 58''6''9 ft²11.9 psf 36%Pass
Portrait 58''6''13.7 ft²11.9 psf 31%Pass
Structural Calculations
Gravity Loading Summary
Load Definitions Initial Pre-PV Load Code Factors Post-PV LoadPg =3 psf | Pf =0.7 x Ce x Ct x Pg Ps = Cs x Pf
Roof Dead Load (D)DL 10.0 psf 10.0 psf 10.0 psf
PV Dead Load (D)PV DL 3.0 psf 0.0 psf 3.0 psf
Roof Live Load (Lr)RLL 20.0 psf 20.0 psf 1.00 0.0 psf
Sloped Snow Load (Pf --> Ps)LL/SL 2.3 psf 1.6 psf 1.00 0.95 1.5 psf
Total Design Load 30.0 psf 14.5 psf
Cd Factor of Governing LC 1.25 (D+Lr)1.15 (D+0.7S)
Total Design Load (Normalized)24.0 psf 12.6 psf
IEBC 5% Check
Net Design Gravity Loading Change (Normalized w/ Cd Factor)-11.4 psf DCR: 53%Pass
AR-02
Roofing Material Roof Pitch Hardware Results Structural Results
Comp Shingle 18°Pass Pass
Hardware Calculations
Attachment Information
Attachment:UltraFoot, Anchor Uplift Force: 0.6(p - (3psf x cos(pitch))) x trib area =133 lb Uplift Capacity: 375 lb a = 5.2 ft
Wind Design Criteria (Partially/Fully Enclosed Method, ASCE 7-22)
Basic Wind Speed V 95 mph Wind Speed - Category II
Wind Pressure Exposure Kz 0.67 Table 26.10-1
Topographic Factor Kzt 1.0 Figure 26.8-1
Wind DIrectionality Factor Kd 0.85 Table 26.6-1
Ground Elevation Factor Ke 1.00 Section 26.9
Velocity Pressure qh = 0.00256 x Kz x Kzt x Kd x Ke x V²13.14 psf Equation 26.10-1
Solar Adjustment Factors γe (Port/Land) =1.2 γa =0.535 Figure 29.4-7
Wind Pressures Zone 1 (up)Zone 2 (up)Zone 3 (up)Down
Ext Pressure Coefficient GCp -1.67 -2.28 -3.02 0.57 Figures 30.3-2(A-H)
Ultimate Design Wind Pressure p = qh x GCp x γe x γa -16.00 psf -16.00 psf -18.07 psf 16.00 psf Equation 29.4-7
Mod Orientation X-Spacing Cantilever Trib Area Demand DCR Final Result
Landscape 58''6''9 ft²11.9 psf 36%Pass
Portrait 58''6''13.7 ft²11.9 psf 31%Pass
Structural Calculations
Gravity Loading Summary
Load Definitions Initial Pre-PV Load Code Factors Post-PV LoadPg =3 psf | Pf =0.7 x Ce x Ct x Pg Ps = Cs x Pf
Roof Dead Load (D)DL 10 psf 10.0 psf 10.0 psf
PV Dead Load (D)PV DL 3 psf 0.0 psf 3.0 psf
Roof Live Load (Lr)RLL 20 psf 20.0 psf 1.00 0.0 psf
Sloped Snow Load (Pf --> Ps)LL/SL 2 psf 1.6 psf 1.00 0.95 1.5 psf
Total Design Load 30.0 psf 14.5 psf
Cd Factor of Governing LC 1.25 (D+Lr)1.15 (D+0.7S)
Total Design Load (Normalized)24.0 psf 12.6 psf
IEBC 5% Check
Net Design Gravity Loading Change (Normalized w/ Cd Factor)-11.4 psf DCR: 53%Pass