The URL can be used to link to this page

Home My WebLink About10141153.pdfTENANT IMPROVEMENT FOR BSIDIAN ENTER AINMEN IN ORPORA ED 1560 E. WARNER AVE. SUITE 220 SANTA ANA, CA " dOMWA o GENERAL NOTES LEGENDPROJECT TEAS SHEET INDEX FIRE �EPTe �OTES (TOTAL: 15 SHEETS) 1. NOTE THAT HIS PROJECT SHALL CONFORM TO THE 1998 EDITIONS OF THE CAUFORNiA BUILDING CODE, INTERIOR/EXTERIOR: N 1997 UNIFORM MECHANICAL CODE, 1997 UNIFORM PLUMBING CODE, THE UNIFORM BUILDING CODE 1. CONTRACTOR SHALL CHECK AND VERIFY SIZE AND LOCATION OF DUCT OPENINGS AND PLUMBING RUNS 1 . FIRE DEPARTMENT FINAL INSPEC1ON REQUIRED. SCHEDULE INSPECTION 2 DAYS IN ADVANCE. PHONE BUILDING MANAGEMENT ARCHITECTURAL SHEETS (12 SHEETS) AND THE 1998 CALIFORNIA ELECTRICAL CODE BASED DI THE S, A NG WITH OF THE NAIT M WITH MECHANICAL CONTRACTOR BEFORE FRAMING WALLS, FLOORS, ETC. (714) 647--5700. NORTH SYMBOL ELECTRIC cflQE, AND CITY AND COUNTY LAWS AND ORDINANCES, ALONG WITH THE CAC. TITLE 24 KRAUS MAN�EMENT SERVICES T1.1 COVER SHEET HANDICAP REQUIREMENTS, AND THE AMERICANS WiTH DISABLLI IES ACT. 2. CONTRACTOR SHALL PROVIDE AND LOCATE WITH MECHANICAL CONTRACTOR ACCESS PANELS AS REQUIRED FOR MECHANICAL DUCTS, PLUMBING RUNS, ETC. ACCESS PANEL LOCATIONS ARE TO BE 2• LOCATIONS AND CLASSIFICATIONS OF FIRE EXTINGUISHERS SHALL BE IN ACCORDANCE WiTH THE UNIFORM 670 W. 17TH, #C-4 T1.2 TITLE 24 NOTES 2. THE TERM 'ARCHITECT" 0R 'DESIGNER" AS USED IN THESE DOCUMENTS REFERS TO: APPROVED BY ARCHITECT PRIOR TO INSTALLATION. FIRE CODE STANDARD 10-1 AND PLACEMENT IS SUBJECT TO THE APPROVAL OF THE FIRE INSPECTOR. COSTA MESA, CA 92627 T1.3 GENERAL NOTES H0� INTERNATIONAL 2A 1OBC MINIMUM FIRE EXTINGUISHERS TO BE LOCATED WITHIN 75 FEET OF TRAVEL DISTANCE FROM A CONTACT: LAURA HUDSON Z915 REDHIIl AVENUE 3. EXTEND ALL STUDS AND WALL MATERIALS TO CONSTRUCTION ABOVE, UNLESS OTHERWISE INDICATED. COLUMN A0.1 SITE PLAN BUILDING B2o1, SUITE C ALL AREAS. PHONE: - 949--574-7350 COSTA MESA, CA 92626 REFERENCE A1.0 EXITING PLAN PHONE: 714 438-3834 4. UNLESS OTHERWISE NOTED, ALL GYPSUM BOARD SURFACES, WALLS, ANQ CEILINGS SHALL BE TAPED � FAX: 949-574-7354 { ) AND FEATHERED SMOOTH TO RECEIVE A MINIMUM OF ONE COAT SEALER AND ONE COAT OF PANT TO 3. STORAGE, DISPENSING OR USE OF ANY FLAMMABLE AND COMBUSTIBLE LIQUIDS, FLAMMABLE AND A2.0 AS-BUILT/DEMO PLAN 3. THE ARCHITECT ASSUMES NO RESPONSIBILITY FOR THE COMPLETENESS OF PLANS FOR BID PURPOSES C°�' COMPRESSED GASES, AND OTHER HAZARDOUS MATERIALS SHALL COMPLY WITH UNIFORM CODE A2.1 PARTITION PLAN PRIOR THE ISSUANCE OF THE BUILDING PERMIT. THE GENERAL CONTRACTOR AND ALL 5. WHERE OCCURS CONTRACTOR SHALL PATCH ANY EXISTING WALLS AND/OR CEILINGS AS NEED TO REGULATIONS. THE STORAGE AND USE OF HAZARDOUS MATERIALS SHALL BE APPROVED BY THE FIRE OWNER A3.0 ELECTRICAL PLAN SUBCONTRACTORS SHALL VERIFY ALL DIMENSIONS AND CONDITIONS ON THE JOB SITE PRIOR TO THE REFURBISH THE LEASE SPACE AND REPAIR ALL DAMAGES CAUSED BY CONTRACTOR. AUTHORITY PRIOR TO ANY MATERIALS BEING STORED OR USED ON -SITE A SEPARATE PLAN SUBMITTAL � DOOR NUMBER BEGINNING OF CONSTRUCTION AND REPORT IMMEDIATELY ANY DISCREPANCIES TO THE ARCHITECT. � CHUNG & COMPANY LLC A4.0 REFLECTED CEILING PLAN 6. INTERIOR WALL AND CEILINGS SHALL BE INSTALLED IN ACCORDANCE TO THE UBC, INCLUDING IS REQUIRED PRIOR TO THE STORAGE AND USE OF HAZARDOUS MATERIALS. A5.0 DOOR &WINDOW SCHEDULE 4. CONTRACTOR IS RESPONSIBLE FOR EXAMINING ALL CONTRACT DOCUMENTS, FIELD CONDITIONS, AND REQUIREMENTS FOR FLAME SPREAD AND SMOKE DENSITY RATINGS FOR FINISH MATERIALS. 1580 CHELSEY RD. 4• BUILDING(S) NOT APPROVED FOR HIGH --PILED STOCK (MATERIALS CLOSELY PACKED PILES OR PALLETS, SAN MARINO, CA 91108 A6.0 FINISH PLAN LNG THAT WORK 1S BUILDABLE AS SHOWN BEFORE PROCEEDING WITH CONSTRUCTION. IF THERE ARE ANY QUESTIONS REGARDING THESE OR OTHER COORDINATION ITEMS, THE CONTRACTOR IS 7• ALL, GLASS SHALL COMPLY WITH THE REQUIREMENTS OF CHAPTER 24 OF THE UBC. RESPONSIBLE FOR OBTAINING CLARIFICATION FROM THE ARCHITECT BEFORE PROCEEDING WITH WORK IN OR IN RACKS WHERE THE TOP OF STORAGE EXCEEDS 12 FEET IN HIGH, AND 6 FEET FOR GROUP A (i, KEY NOTE CONTACT: JASON CHUNG A7.0 DETAIL SHEET QUESTION OR RELATED WORK. 8. WHEN USED, ALL NOISE BARRIER BATTS (SOUND INSULATION).AND INSULATION BATTS SHALL BE PLASTICS AND CERTAIN OTHER HIGH -HAZARD COMMODITIES). HIGH -PILED STOCK SHALL BE APPROVED BY PHONE: 626--403-0555 4 5. THE GENERAL CONTRACTOR IS SOf.EY RESPONSIBLE TO COORDINATE W►T}T ALL SUB -CONTRACTORS PER NON-COMBUSTIBLE AND SHAll. NOT CONTAIN OR Ui1LJZE OZONE DEPLETING COMPOUNDS. THE FIRE AUT1•IORiil' PRIOR TO MATERIALS BEING STORED ON�-SITE. A SEPARATE PLAN SUBMITTAL IS REQUIREMENTS ESTABLISHED BY OWNER, TENANT, OR BOTH, WHICH ARE UNDER SEPARATE CONTRACT s. CONTRACTOR SFIALt. PROVIDE BACKING >d ALL PARTITIONS THAT REQUIRE MILLWORK INSTALLATION. REQUIRED FOR HIGH -PILED STORAGE IN ACCORDANCE WITH THE UNIFORM FIRE CODE, ARTICLE 81. CLIENT WITH THE OWNER, OR TENANT, OR BOTH. ELEVATION CALLOUT , . 6. THE STRUCTURAL., MECHANICAL, ELECTRICAL, PLUMBING, OTHER DRAWINGS, AND JOB SPECIFICATIONS 5• ALL WEATHER ACCESS ROADS SHALL BE APPROVED BY THE OCFA AND IN PLACE BEFORE ANY OBSIDIAN ENTERTAINMENT ARE SUPPLEMENTARY TO ARCHITECTURAL. CONSTRUCTION DRAWINGS. ANY DISCREPANCIES BETWEEN COMBUSTIBLE MATERIALS ARE PLACED ON THE SITE. ACCESS ROADS SHALL BE MAINTAINED CLEAR OF MECH��NICAL _ {� ,S 7, S) INCORPORATED AL s THESE DOCUMENTS SHALL BE IMMEDIATELY BROUGHT TO THE ATTENTION OF THE ARCHITECT FOR OBSTRUCTION. M 1 HVAC PLAN CLARIFICATION. DOORS . AND EXITS: 1560 E. WARNER AVE., SUITE 208 SANTA ANA, CA 7. THE INTENT OF DRAWINGS AND SPECIFICATIONS 15 TO INCLUDE ALL LICENSED TABOR, COMMERCIAL 1. PER UBC SECTION 2406, GLASS DOORS, ADJACENT GLAZING PANED AND All GLAZED OPENINGS 6. ACCESS GATES SHALL BE IN COMPLIANCE WITH THE UNIFORM FIRE CODE, SECTION 902 AND ORANGE DETAIL CALLOUT GRADE MATERIALS AND SERVICES NECESSARY FOR THE COMPLETiON OF ALL WORK SHOWN, DESCRIBED CONTACT: FEARGUS URQUHART OR REASONABLY IMPUED, BUT NOT UMITED TO THAT EXPUC17LY INDICATED IN THE CONTRACT WITHIN 18 INCHES OF THE ADJACENT FLOOR SHALL BE OF GLASS APPROVED FOR IMPACT COUNTY FIRE AUTHORITY GUIDELINES. A SEPARATE PLAN SUBMITTAL AND APPROVAL BY THE ORANGE PHONE: 714-436--1006 DOCUMENTS. HAZARDS. COUNTY FIRE AUTHORITY IS REQUIRED. ELECTRICAL (2 SHEETS) 8. CONTRACTOR FOR THE PROJECT SHALL BE RESPONSIBLE FOR OBTAINING ALL REQUIRED BUILDING 2. EXIT DOORS SHALL SWING IN THE DIRECTION OF EXIT TRAVEL WHEN SERVING ANY HAZARDOUS E--1 ELECTRICAL NOTES, SCHED. PERMITS. PRIOR TO THE ISSUANCE OF A BUILDING PERMIT, THE APPLICANT SHALL HAVE EVIDENCE OF 7. PLANS OF NEW OR MODIFICATIONS TO EXISTING FIRE PROTECTION, DETECTION, ALARM OR MONITORING CURRENT WORKMAN'S COMPENSATION INSURANCE COVERAGE ON FILE WITH THE DEPARTMENT IN+ OR WHEN THE AREA SERVER HAS AN OCCUPANT LOAD OF 50 OR MORE PEOPLE. SYSTEM(S) SHALL BE APPROVED BY THE FiRE AUTHORITY PRIOR TO INSTALLATION, A SEPARATE PLAN PLANNER E-2 LIGHTING AND POWER PLANS COMPLIANCE WITH SECTION 3800 OF THE CALIFORNIA LABOR CODE SUBMITTAL AND APPROVAL BY ORANGE COUNTY FIRE AUTHORITY IS REQUIRED PRIOR TO THE REVISION INDICATOR BOLE' INTERNATIONAL 3. ALL EXITS ARE TO BE OPENABLE FROM THE INSIDE WITHOUT THE USE OF A KEY OR SPECIAL COMMENCEMENT OF ANY WORK. 9. THE GENERAL CONTRACTOR SHALL NOTIFY THE ARCHITECT IMMEDIATELY OF ANY SPECIFIED MATERIALS KNOWLEDGE. PROVIDE A SIGN ON OR NEAR THE MAIN EXIT DOOR READING, 'THIS DOOR TO 2915 REDHILL AVE. OR EQUIPMENT WHICH ARE EITHER UNAVAILABLE OR THAT WILL CAUSE A DELAY IN THE CONSTRUCTION REMAIN UNLOCKED DURING BUSINESS HOURS'. 'i BLDG. B201, SUITE C COMPLETION SCHEDULE THE CONTRACTOR SHAM SUBMIT CONFIRMATIONS OF DELIVERY DATES FOR 8. A LETTER OF INTENDED USE FOR THE STRUCTURE(S) MAY BE REQUIRED BY THE FIRE INSPECTOR. COSTA MESA, CA 9262fi ORDERS OF MATERIALS AND EQUIPMENT. 4. ALL HARDWARE SHALL BE INSTALLED 3 FEET ABOVE FINISH FLOOR, UNLESS OTHERWISE NOTED. CONTACT: JEFFCA 2626 i0. THE ARCHITECTS APPROVAL OF SHOP DRAWINGS SHALL NOT RELIEVE THE GENERAL. CONTRACTOR OR ADLER CONTRACTOR TO VERIFY & MATCH EXISTING CONDITIONS. g• WHEN THE PROJECT INVOLVES THE CONSTRUCTION OF A NEW STRUCTURE OR AN ADDITION TO AN PHONE: 714 438-3834 SUBCONTRACTOR FROM RESPONSIBILITY FOR DEVIATIONS FROM THE DRAWINGS OR SPECIFICATIONS EXISTING STRUCTURE PLANS AND DOCUMENTATION FOR FIRE DEPARTMENT ACCESS HYDRANT LOCATIONS ' UNLESS HE HAS IN WRITING AND BROUGHT TO THE ON OF CITE ' ' ' , E ATTENTION THE ARCHITECT CT SUCH DEYGlT10N5 - 5 ALL HARDWARE TO BE LEVER TYPE PER STATE OF CALIFORNfA, TITLE 24, AND THE ADA WATER AVAILABILITY AND FIRE LANE MARKINGS SHALL BE, SUBMITTED TO AND APPROVED BY THE ORANGE e AT PO TIME OF THE SUBMISSION, NOR SHALL R RELIEVE HIM (GENERAL CONTRACTOR) FROM COUNTY FIRE AUTHORITY PRIOR TO THE APPROVAL OF ARCHITECTURAL PLANS. AN ORANGE COUNTY FIRE GENERAL_ CONTRACTOR r= RESPONSIBILITY FOR ERRORS OF ANY SORT IN THE SHOP DRAWINGS. s. SPECIAL LOCKING DEVICES SHAL BE OF AN APPROVED TYPE. AUTHORITY APPROVED SITE PLAN SHALL BE SUBMITTED WITH THE ARCHITECTURAL PLANS. 11. UNLESS OTHERWISE NOTED IN THE CONTRACT DOCUMENTS, THE CONTRACTOR SHALL SUBMIT ONE 7. PROVIDE WEATHER SEALS ON ALL EXTERIOR DOORS PER ANSI STANDARDS. SHOWCASE CONTRACTING f. BLUEPRINT SET AND ONE SEPIA SET OF SHOP DRAWINGS. SHOP DRAWINGS SHOULD INCLUDE DETAILED DIAGRAMMATIC DRAWINGS, AND MATERIAL. SCHEDULES. LOCATION AND OR►ENTATION OF All 10. IN STRUCTURES OF UNDETERMINED USE, THE MINIMUM FIRE SPRINKLER DESIGN DENSITY REQUIRED ITEMS SHOULD BE CLEARLY INDICATED. BEGIN FABRICATION OF SHOP ITEMS AFTER RECEIVING $. MAXIMUM UNDERCUT OF ALL DOORS SHALL NOT EXCEED 1/2' ABOVE FINISH FLOOR SURFACE. SHALL BE ORDINARY HAZARD GROUP 2) WITH A DESIGN AREA OF 3,000 SQUARE FEET. SERVICES, INC. ARCHITECTS OR DESIGNERS APPROVAL OF SHOP DRAWINGS. 17751 METZLER HUNTINGTON BEACH CA 92647 s. THRESHOLDS SHALL NOT EXCEED 1 2' IN HEIGHT &MUST BE FULLY ACCESSIBLE. 11. AN AUTOMATIC EXTINGUISHING SYSTEM SI-wLL BE PROVIDED TO PROTECT COMMERCIAL TYPE FOOD NEAT 12. ANY WORK INSTALLED iN CONFLICT WITH THE CONSTRUCTION DRAWINGS, WIMOUT THE PRIOR / - APPROVAL OF THE OWNER AND THE ARCHITECT SHALL BE CORRECTED AT THE CONTRACTOR'S PROCESSING EQUIPMENT THAT PRODUCES A GRASE-LADEN VAPORS. A SEPARATE PLAN SUBMITTAL iS CONTACT: JOHN MITSUMORI O c,Co EXPENSE. 10. CONTRACTOR SHALL REFINISH ANY BLEMISHED DOORS OR REPLACE SAID DOOR IF NOT ABLE TO PHONE: 714 596-5655 $ "' �''' �„ �. ,. 7R,�-:�, REQUIRED FOR THE INSTALLATION OF THE SYSTEM AND SHALL BE IN ACCORDANCE WITH UFC ARTICLE ( ) °` °° I REFINISH TO 'AS NEW` CONDITION. 10, NFPA 17A AND 96. FAX: (714) 596-7659 13. INSTALL ALL MANUFACTURED ITEMS, MATERIALS, AND EQUIPMENT IN STRICT ACCORDANCE WITH THE GA LICENSE: 767594 - Fw :.r #'}' MANUFACTURERS SPECIFICATIONS. ELECTRICAL: 14. PROVIDE CONTINUOUS INSPECTION AS SET FORTH IN UBC SECTION 108 AND PER CONTRACT DOCUMENTS AS NEEDED. 1. WHERE EXIT SIGNS ARE REQUIRED BY UBC SECTION 1013 SHALL BE ILLUMINATED PER SECTION BUILDING DATAVICINITY 15. PRIOR TO THE ISSUANCE OF FINAL CERTIFICATE -OF OCCUPANCY FOR THIS PROJECT, THE GENERAL 1012 AND 1994 NEC. THE LDCAiION SHAM BE COORDINATED WTM THE ARCHTfECL MAP CONTRACTOR SHALL SUBMIT A SIGNED CERTIFICATE TO THE DEPARTMENT OF BUILDING AND SAFETY STATING THAT ALL WORK HAS BEEN PERFORMED AND MATERIALS INSTALLED ACCORDING TO THE PLANS 2. PROVIDE BACK-UP POWER FOR EXIT SIGNS PER UBC SECTION 1012. AND SPECIFICATIONS AFFECTING NON-RESIDENTIAL ENERGY. DRAWING NOTES: 3• EMERGENCY LIGHTING SHALL BE 2 SEPARATE SOURCES OF POWER AND SHAD. COMPLY WiTH THE BUILDING D PEA CITY OF SANTA ANA c I. UNLESS OTHERWISE NOTED OR INDICATED, ALL DIMENSIONS ON THESE DOCUMENTS SHALL BE FROM T3 . 4 . THE CENTERUNE OF THE COLUMNS TO THE FACE OF EITHER WALL STUD OR FINISHED FACE OF 4• WHEN PLYWOOD BACKBOARDS ARE REQUIRED 1N TELEPHONE AND ELECTRICAL EQUIPMENT ROOMS, Oka, 4 R� s EXISTING WALLS. THEY SHALL BE PAINTED TO MATCH ADJACENT WALL BUILDING CODE 2001 EDITIONS OF THE CALIFORNIA BUILDING CODE, UNIFORM 7, MECHANICAL CODE, UNIFORM PLUMBING CODE, AND CALIFORNIA t_> � � 1�' � �� y � 2. ALL VERTICAL DIMENSIONS SHOWN ARE FROM FLOOR SLAB, UNLESS OTHERWISE NOTED. 5. THE CENTER OF SWITCHES SHALL BE NO MORE THAN 48 INCHES ABOVE THE FLOOR, VERIFY AND ELECTRICAL CODE BASE ON THE 1999 EDITION OF THE NATIONAL 3. DIMENSIONS SHOWN IN FIGURES TAKE PRECEDENCE OVER DIMENSIONS SCALED FROM DRAWINGS. MATCH EXISTING. ELECTRIC CODE AND CiTY AND COMMUNITY LAWS AND ORDINANCES.-, LARGE SCALE DRAWINGS AND DETAILS TAKE PRECEDENCE OVER SMALLER SCALE DRAWINGS. m t, fi z v us wF''c" G�""* },$tii3 6. CENTERUNE OF 15, 20, AND 30 AMP RECEPTACLES SHALL NOT BE LESS THAN 15 INCHESt4mT'° T � ?' w'&.g 4. THE TERM "ALIGN , AS USED IN THESE DOCUMENTS, SHALL. MEAN TO ACCURATELY LOCATE FINISHES IN -,ns :anm � aO �w .a CENTERED ABOVE FLOOR. FLOOR OUTLETS ARE ACCEPTABLE NEXT TO SLIDING PANELS / YIALLS JOB SITE ADDRESS 1560 E. WARNER AVE. THE SAME PLANE. AND OTHER SPECIAL CONVENIENT LOCATIONS. SANTA ANA CA _ P�§§` ,:::t {;> Y A� g TIBu c:a �F,f�h Kh &, "£"t... es rr}2�'ti`SS s dim � - has �".. 4l G - 5st 8+.i sa+u?v.' � $Si�� • G' me a•. ; fi sFs9 a' o7w'a f' �s' 5. NO HAZARDOUS MATERIALS SHALL BE USED OR STORED WITHIN THE BUILDING WHICH DOES NOT SOT I ,,� OyT �v i t � ., i I, TT OT1 �T s � COMPLY WITH 1H£ UBC TABLES 3-D THROUGH 3G, AND UFC., AND STATE AND COUNTY 7• IXiT ILLUMINATION SHALL. BE FROM AN EMERGENCY SYSTEM WHERE EXITING SYSTEMS SERVES AN � � � � � �� , °�� COMPLF WITHS. OCCUPANT LOAD OF 100 OR MORE. LCBC SECTION 1012.2 . � � Cif Sci-nit � Aria. REQUIRFLOOR 2 STORY BLDG, SUITE 220 0 6. ALL. APPLICABLE PERMITS (BUILDING, li��ZARDOUS MATERIAL, ETC.) MUST BE OBTAINED PRIOR TO � � � � The C�� a��S � � C" "C I ° ns �� NOT flccL1PANC1', TITLE 24 ENERGY COMPLIANCE. TENANT OBSIDIAN ENTERTAINMENT INCORPORATED IT I � ��imwail �, n v I 1. ENVELOPE COMPLIANCE AND STATEMENT OF DESIGN COMPLIANCE: THE CAUFORNiA ENERGY TO� S C Of ! Cityi gTC �r Slat- L&N` JOB SITE: CONSERVATION STANDARDS FOR NON-RESIDENTIAL BUILDING SHALL BE REVIEWED AND COMPLIED BUSINESS OFFICE E. WARNER WE. i . WHERE IX1S11NG TENANTS BUSINESSES ARE ADJACENT} TO THE JOB SITE TENANT, 1H£ WWII DURING THE CONSTRUCTION AND TENANT IMPROVEMENT WORK SCOPE OF THIS PROJECT. - - � � , CONTRACTOR SHALL MINIMIZE CONSTRUCTION NOISE - EXTREME NOISE CONSTRUCTION SHALL OCCUR CONSTRUCTION TYPE TYPE V N, (NON SPRINKLERED) OCCsod Date AT NON -TYPICAL BUSINESS HOURS. CONTRACTOR SHOULD NOTIFY BUILDING REPRESENTATIVE OF VENTILATION: I OCCUPANCY GROUP B e SPECIAL CIRCUMSTANCES IN ADVANCE PRIOR TO WORK. I F SATA ANA 2. THE CONTRACTOR AT HIS OWN EXPENSE, SHALL KEEP THE PROJECT AND SURROUNDING AREA FREE 1 • UNLESS OTHERWISE NOTED, All fa1CL0.SEQ PORTIONS OF BUILDINGS CUSTOMARILY OCCUPIED BY SUITE AREA +�-- 4,503 USF PEOPLE SHALL BE PROVIDED WITH NATURAL VENTILATION BY MEANS OF OPENING EXTERIOR FROM DUST AND DEBRIS. THE WORK SHALL BE IN CONFORMANCE WITH AIR AND WATER POLLUTION � � a CONTROL STANDARDS AND REGULATIONS OF THE STATE DEPARTMENT OF HEALTH. OPENINGS WITH AND AREA NOT LESS THAN 1 ZO OF THE TOTAL FLOOR AREA, OR SHALL BE '� • / REMODELED AREA +/-- 600 USF TO INCLUDE (2) P.O., (1) I.T. ROOM . PROVIDED WITH A MECHANICALLY OPERATED VENTILATION SYSTEM. MECHANICALLY OPERATED $G j ENLARGED P 0. 3. CONSTRUCTION DEBRIS AND WASTES SHALL BE DEPOSITED AT AN APPROPRIATE SITE. THE VENTILATION SYSTEM SHALL BE CAPABLE OF SUPPLYING MIN. OF 15 CUBIC FEET PER MIN. ) � r t 0 CONTRACTOR SHALL INFORM THE BUILDING REPRESENTATIVE OF THE LOCATION OF DISPOSAL SITES. PROJECT SITE �j OUTSIDE AIR PER OCCUPANT DURING SUCH 11ME AS THE BUILDING IS OCCUPIED. IF THE VELOCITY HOTEL TERRACE 1/ 4. CONTRACTORS SHALL BE RESPONSIBLE FOR THE GENERAL CLEANING OF THE JOB AFTER iTS OF AR AT A REGISTER EXCEEDS 10 FEET PER SECOND, THE REGISTER SHALT. BE PLACED MORE PARKING IN COMPLIANCE COMPLETION. WHERE APPLICABLE, CLEANING SHALL INCLUDE, BUT NOT BE UMITED TO, THE EXTERIOR THAN 8 FEET' ABOVE THE FLOOR DIRECTLY BENEATH. ABC SECTION 1202.2.1 � AND THE INTERIOR OF THE BUILDING, THE PATH OF TRAVEL TO THE JOB SiTE, PARKING LOTS, ELEVATORS, LOBBIES, AND CORRIDOR CARPETS. 2. UNLESS OTHERWISE NOTED, TOILET ROOMS SHALL BE PROVIDED WITH A FULLY OFENABLE EXTERIOR WINDOW AT LEAST 350 SO. INCHES OR A VERTICAL DUCT NOT LESS THAN 100 SO. INCHES IN SCOPE OFWORK: TENANT IMPROVEMENTS OF EXISTING OFFICE SPACE FOR 5. WHERE REQUIRED. SHALL PROVIDE PEDESTRIAN PROTECTION IN ACCORDANCE WiTH UBC CHAPTER 33, AREA FOR THE FIRST WATER CLOSET PLUS 50 ADDITIONAL SQ. INCHES FOR EACH ADDmoN& APPROXIMATELY +/-- 4,503 U.S.F. OF B OCCUPANCY USE TO WATER CLOSET, OR A MECHANICALLY OPERATED EXHAUST SYSTEM CAPABLE OF PROVIDING A INCLUDE NEW METAL STUDS, NEW DOORS & FRAMES, INCLUDING 6. IF TRENCHES OR EXCAVATIONS 5' OR MORE IN DEPTH ARE REQUIRED, OBTAIN NECESSARY ISSUANCE COMPLETE AIR CHANGE EVERY 15 MINS. SUCH MECHANICALLY OPERATED EXHAUST SYSTEMS SHALT. ELECTRICAL, MECHANICAL AND PLUMBING. NO CHANGES TO BUILDING OF A BUILDING OR GRADING PERMIT. BE CONNECTED DIRECTLY TO THE OUTSIDE, AND THE POINT OF DISCHARGE SHALL BE AT LEAST 3 ENVELOPE OR EXISTING CEILING. PROPERTY IN FULL A.D.A, TITLE 24 FEET FROM ANY OPENINGS WHICH ALLOWS AIR ENTRY INTO OCCUPIED PORTIONS OF THE BUILDING. COMPLIANCE. APPROVED UBC SECTION 1202.2.1 PILANNING DIVISION N MASTERI.D.: G. : € nce �.� R. A(CTI TYPE:..��. ABBREVIATIONS ry PLANNER: AFT= above finished floor BLDG building CONT continuous or continue ELEV elevator FIR frame (d), (ing) HB hose Bibb MFR manufacture (er) OPP opposite REG register SUS suspended WC water closet DATE: AP access panel CAB cabinet CONTR contract (or) ENCL enclosure (ure) FUR furred (ing) INCL Include (d), (ing) MAIL material (s) OD outside diameter SCH schedule TEL telephone W width, wide T NSF EI) B`s:� ACT acoustical tile CPT carpet (ed) CTR counter EP electrical. panel board GA gage, gouge ID inside diameter MAX maximum OH overhead SEC section THK thick (ness) WP waterproofing .. ADJT adjustable CB catch basin DEMO demolish, demolition EQ equal GC general contract (or) INS insulate (d), (ing) MECH mechanic (al) PNL panel SS service sink THR threshold WDW window _ .,, ..., ... :.,a °�� .w. r,ATE: A/C air conditioning CLG ceiling DET detail EQP equipment GL glass, glazing KPL kickplate MED medium PART' partition Sc solid core T&G tongue and groove WG wired glass ALT alternate CEM cement DIAG diagonal EXH exhaust GDNO g grade, grading KiT kitchen MET metal PVMT pavement S1M similar TSL top of slab WM wire mess ?LA G F.11 rya . ;Cgs. i=L YESar AL aluminum CM centimeter s DLA diameter EX existing GYP.BD. sum board LAB laboratory MIN minimum SP soundproof TST to of steel W 0 without " ° `'° v {) 9 gypsum rY PED pedestal p P /~ AB anchor bolt CT ceramic the DIM dimension EXP exposed HDW hardware LB lag bolt MISC. miscellaneous PLAM plastic laminate SPK speaker TW top of wall WD wood w ' CONTACT' ANOD anodized CIR circle DIV division EXT exterior HDR header J joist MOD modular SPEC specification s TYP typical W with .; j PLYWD plywood p () YP / APPROX approximate CLR clear (once) DR door FOC face of concrete HVAC heating/ventilating/ LAM laminate d MT mount ed , in SQ square UC undercut CONTACT ( I4) � " q/ {) { ) (ing) PSF pounds per square foot q ARCH architect (ural) CLS closure D drain FOM face of masonry HT height LAV lavatory NAT natural PSI ZN 9 ry pounds per square inch SST stainless steel UNF unfinished 53 CTTO(7 'DIn0NQ BELOW, AUTO automatic COL column DWG drawing FOS face of studs HC hollow core L length NOM nominal PL property line STD standard VB vapor barrier BL.K block CONC concrete DF drinking fountain FF finish floor HM hollow metal LT light NIC not in contract RAD radius STL steel VERT vertical BL.KG blocking COND condition ELEC electric (al) FIN finish (ed) HM hollow metal MB machine bolt NTS not to scale REF reference STOR storage WSCT wainscot -' BOT bottom CONST construction EL elevation FTC footing HOR horizontal MH manhole OC on center (s) REFR refrigerator STRUCT structural WH wall hung ` EmOvIvE' IL & DMGN 2916 MMM L Ava= BZTtLMG B201, Ou C COSTA IUMA, CAIMMU 714AW.98M 11fts -its- UJ N Q So '` W Of >< W 0 C,�< r� W < Z LU 0 �U C) CD LO ' ..�.. ° THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN AS AN WSTRUMENT OF PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED IN WHOLE OR PART FOR ANY PROJECT OTHER THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION OF BOLE INTERNATIONAL. THIS DOCUMENT SHALL NOT BE REPRODUCED OR MODIFIED IN ANY WAY WITHOL,TT THE EXPRESSED WRITTEN CONSENT OF BOLE' INTERNATIONAL. REVISIONS: 0 9t2103 -PROJECT START © 9/5103 - CITY SUBMITTAL Q9129/03 -CITY REVISIONS ® 1011103 - MY RESUBM rrFAL 47 PARTICIPANTS i DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED BY: J.A. USABLE: +/- 4,503 U.S.F. RENTABLE: PROJECT: JOB: OBSIDIAN ENT. DATE: SCALE: AS NOTED SHEET NAME � TITLE SHEET SHEET O T1.1 ` DISABLED ACCESS GENERAL NOTES NOTE: ACCESSIBLE ROUTE OF TRAVEL IS DEFINED AS "A CONTINUOUS UNOBSTRUCTED PATH 4. THE WIDTH OF THE LANDING SHALL EXTEND 24" PAST THE STRIKE EDGE OF ANY DOOR OR 8) A WATER CLOSET FIXTURE LOCATED IN A COMPARTMENT SHALL PROVIDE A MINIMUM ii) L-SHAPED GRAB BARS LOCATED ON WALLS ADJACENT TO AND OPPOSITE THE CONNECTING ALL ACCESSIBLE ELEMENTS AND SPACES IN AN ACCESSIBLE BUILDING OR GATE FOR EXTERIOR RAMPS AND 18" PAST THE STRIKE EDGE FOR INTERIOR RAMPS. 28" WIDE CLEAR SPACE FORM A FIXTURE OR A MINIMUM 32" WIDE CLEAR SPACE SEAT. GRAB BARS SHALL COMPLY WITH DIAMETER, LOADING, AND FACILITY THAT CAN BE NEGOTIATED BY A PERSON WITH A SEVERE DISABILITY USING CBC SEC. 1007.4.4A & FIG. 118-39. FORM A WALL AT ONE SIDE OF THE WATER CLOSET. THE OTHER SIDE OF THE PROJECTION REQUIREMENTS OF CBC SECTION 11158.8. GRAB BARS SHALL BE A WHEELCHAIR, AND THAT IS ALSO SAFE FOR AND USABLE BY PERSONS WITH OTHER 'PATH WATER CLOSET SHALL PROVIDE 18" FORM THE CENTER LINE OF THE WATER CLOSET NOT LESS THAT 24" BY 36" IN LENGTH, WITH THE 36" SIDE ON THE WALL DISABILITIES, AND THAT ALSO IS CONSISTENT WITH THE DEFINITION OF OF TRAVEL' 5. AT BOTTOM AND INTERMEDIATE LANDINGS, THE WIDTH SHALL BE AT LEAST THE SAME AS TO THE WALL. GRAB BARS SHALL NOT PROJECT MORE THAN 3" INTO THESE CLEAR HAVING THE SHOWER HEAD AND CONTROLS. IN CBC SECTION 217.4 AND 11028. REQUIRED FOR THE RAMP. CBC SEC. 1007.4.5A & FIG. 118-38. SPACE. CBC SEC. 11158.7.1.2 & FIG, 11 B-18. 1. AT LEAST ONE ACCESSIBLE; ROUTE -WITHIN THE BOUNDARY OF THE SITE SHALL BE 6. INTERMEDIATE AND BOTTOM LANDINGS AT A CHANGE OF DIRECTION IN EXCESS OF 30 C) A MINIMUM 48" LONG CLEAR SPACE SHALL BE PROVIDED IN FRONT OF THE WATER ii1) GRAB BARS MOUNTED 33" TO 36" ABOVE THE SHOWER FLOOR. PROVIDED FROM PUBLIC TRANSPORTATION STOPS, ACCESSIBLE PARKING, ACCESSIBLE DEGREES SHALL HAVE A DIMENSION IN THE DIRECTION OF RAMP RUN OF NOT LESS THAN CLOSET IF THE COMPARTMENT HAS AN END OPENING DOOR AND A MINIMUM 60 iv) SOAP DISH LOCATED ON THE CONTROL WALL AT A MAXIMUM HEIGHT OF 40 " PASSENGER LOADING ZONES, AND PUBLIC STREETS OR SIDEWALKS TO THE ACCESSIBLE 72" TO ACCOMMODATE THE HANDRAIL EXTENSION. CBC SEC. 1007.4.6A, FIG. 118-38 (B) LONG CLEAR SPACE SHALL BE PROVIDED IN FRONT OF THE WATER CLOSET IF THE ABOVE THE FLOOR. BUILDING ENTRANCE THEY SERVE. WHEN MORE THAN ONE ROUTE IS PROVIDED, ALL & 11 B-39 (A). COMPARTMENT HAS A DOOR LOCATED AT THE SIDE. GRAB BARS SHALL NOT PROJECT ROUTES SHALL BE ACCESSIBLE. CBC SEC. 1114B.1.2. MORE THAN 3" INTO THESE CLEAR SPACES. CBC SEC. 1115B.7.1.2, FIG. 1118-1A E) SHOWERS SHALL BE FINISHED WITH A SMOOTH, HARD, NONABSORBENT SURFACE SUCH 14 2. WHEN MORE THAN ONE BUILDING OR FACILITY IS LOCATED ON A SITE, ACCESSIBLE 7. OTHER INTERMEDIATE LANDINGS SHALL HAVE A DIMENSION IN THE DIRECTION OF RAMP RUN OF NOT LESS THAN 60". CBC SEC. 1007.43A & FIG. 118-38 (A). & 1 B. AS PORTLAND CEMENT, CONCRETE, CERAMIC TILE OR OTHER APPROVED MATERIAL TO HEIGHT OF NOT LESS THAN 70" ABOVE THE DRAIN INLET. MATERIALS OTHER THAN ROUTES OF TRAVEL SHALL BE PROVIDED BETWEEN BUILDINGS AND ACCESSIBLE SITE D) WATER CLOSET COMPARTMENTS SHALL BE EQUIPPED WITH A DOOR THAT HAS AN STRUCTURAL ELEMENTS USED IN SUCH WALLS SHALL BE OF A TYPE WHICH IS NOT FACILITIES. CBC SEC. 1114B.1.2 & 11278.1. 8. *RAMP LANDINGS ARE NOT CONSIDERED IN DETERMINING THE MAXIMUM HORIZONTAL AUTOMATIC -CLOSING DEVICE, AND SHALL HAVE A CLEAR, UNOBSTRUCTED OPENING ADVERSELY AFFECTED, BY MOISTURE. CBC SEC. 1115B.9.6. 3. THE ACCESSIBLE ROUTE OF TRAVEL SHALL "BE THE MOST PRACTICAL DIRECT ROUTE DISTANCE OF EACH RAMP. CBC SEC. 1007.4.1A, WIDTH OF 32" WHEN LOCATED AT THE END AND 34" WHEN LOCATED AT THE SIDE WITH THE DOOR POSITIONED AT AN ANGLE OF 90 DEGREES FROM ITS CLOSED F) A FLEXIBLE HAND-HELD SHOWER UNIT WITH A HOSE AT LEAST 60" LONG SHALL BE BETWEEN ACCESSIBLE BUILDING ENTRANCES, ACCESSIBLE SITE FACILITIES, AND 9. HANDRAILS SHALL BE PLACED ON EACH SIDE OF EACH RAMP, SHALL BE CONTINUOUS POSITION. CBC SEC. 1115B.7.1.3, FIG. 11 B-1A & 18. PROVIDED WITH A HEAD MOUNTING HEIGHT OF 48" + 1" MAXIMUM ABOVE THE THE ACCESSIBLE ENTRANCE TO THE SITE TO THE MAXIMUM EXTENT FEASIBLE, THE FULL LENGTH OF THE RAMP, SHALL BE 34" TO 38" ABOVE THE RAMP, SHALL SHOWER FLOOR. CBC SEC 1505(8) & FIG. 11 B-2A. COINCIDING WITH THE ROUTE FOR THE GENERAL PUBLIC." CBC SEC. 1114B.1.2 & 11278.1. EXTEND A MINIMUM OF 1' BEYOND TOP AND BOTTOM OF THE RAMP, AND THE ENDS E) WHEN STANDARD COMPARTMENT DOORS ARE USED, WITH A MINIMUM 9" CLEARANCE 4. PROVIDE SIGNS DISPLAYING THE INTERNATIONAL SYMBOL OF ACCESSIBILITY AT EVERY SHALL BE RETURNED. CBC SEC. 1007.5A, FIG. 11 B-27 (8) & (C). FOR FOOTRESTS UNDERNEATH AND A SELF -CLOSING DEVICE, CLEARANCE AT THE G) WATER CONTROLS FOR SHOWERS OF A SINGLE LEVER DESIGN SHALL BE LOCATED ON PRIMARY PUBLIC ENTRANCE AND AT EVERY MAJOR JUNCTION ALONG OR LEADING TO AN 10. ANY WALL OR OTHER SURFACE ADJACENT TO THE HANDRAILS SHALL BE FREE OF SHARP STRIKE EDGE AS SPECIFIED IN SECTION 1004.9.2.2 IS NOT REQUIRED. SEC. 11158.7.1.3. THE SIDE WALL OPPOSITE THE SEAT, 40 + 1" ABOVE THE SHOWER FLOOR, AND SHALL BE OPERABLE WITH A MAXIMUM FORCE OF 5 LBS. CBC SEC. 1505(A) & ACCESSIBLE ROUTE OF TRAVEL. SIGNS SHALL INDICATE THE DIRECTION TO ACCESSIBLE OR ABRASIVE ELEMENTS. EDGES SHALL HAVE A MINIMUM RADIUS OF 1/8". FIG, 11B-2A, BUILDING ENTRANCES AND SHALL COMPLY WITH CBC SECTION 11178.5. SEC. 11278.3. CBC SEC. 1007.5A & FIG. 118-36 (C). F) THE INSIDE AND OUTSIDE OF THE COMPARTMENT DOOR SHALL BE EQUIPPED WITH WALKS & SIDEWALKS A LOOP OR U-SHAPED HANDLE IMMEDIATELY BELOW THE LATCH. THE LATCH SHALL H) WHERE, WITHIN THE SAME FUNCTIONAL AREA, TWO OR MORE SHOWERS ARE PROVIDED 11. WHERE THE RAMP SURFACE IS NOT BOUNDED BY A WALL OR FENCE AND THE RAMP EXCEEDS BE FLIP -OVER STYLE, SLIDING, OR OTHER HARDWARE NOT REQUIRING THE USER TO FOR THE PHYSICALLY HANDICAPPED, THERE SHALL BE AT LEAST ONE SHOWER 10- IN LENGTH, THE RAMP SHALL COMPLY WITH ONE, OF THE FOLLOWING REQUIREMENTS: OR TWIST, CBC SEC. 11158.7.1.3. CONSTRUCTED OPPOSITE HAND FROM THE OTHER OR OTHERS (I.E., ONE LEFT HAND 1. WALKS AND SIDEWALKS SHALL HAVE A CONTINUOUS COMMON SURFACE, NOT INTERRUPTED CBC SEC. 1007.10, FIG. 118-27 (8) & (C). CONTROL VS. RIGHT NAND CONTROLS). CBC SEC. 1505(D). BY STEPS OR BY ABRUPT CHANGES IN LEVEL EXCEEDING 1 /2", AND SHALL BE A MINIMUM OF 48" IN WIDTH. CBC SEC. 1023.1. G ) EXCEPT FOR DOOR OPENING WIDTHS AND DOOR SWINGS A CLEAR UNOBSTRUCTED I) WHERE ACCESSIBLE SHOWER FACILITIES ARE PROVIDED IN AREAS SUBJECT TO a) A GUIDE CURB A MINIMUM OF 2" IN HEIGHT SHALL BE PROVIDED AT EACH SIDE OF " ACCESS NOT LESS THAN 44SHALL 8E PROVIDED TO WATER CLOSET COMPARTMENTS EXCESSIVE VANDALISM, IN LIEU OF PROVIDING THE FIXED FLEXIBLE HOSE AND 2. WHEN ABRUPT CHANGES IN LEVEL NOT EXCEEDING 1/2n OCCUR, THEY SHALL BE BEVELED THE RAMP. DESIGNED FOR USE BY PERSONS WITH DISABILITIES AND THE SPACE IMMEDIATELY HAND-HELD SHOWER HEAD, TWO WALL MOUNTED SHOWER HEADS SHALL BE WITH A SLOPE NO GRATER THAN 1:2, EXCEPT THAT LEVEL CHANGES NOT EXCEEDING 1 /4" IN FRONT OF A WATER CLOSET COMPARTMENT SHALL BE NOT LESS THAN 48" AS INSTALLED EACH SHOWER HEAD SHALL BE CONTROLLED SO THAT 1T CAN BE MAY BE VERTICAL. CBC SEC. 1023.4 & FIG, 118-5E(C) & (D). " b) A WHEEL GUIDE RAIL SHALL BE PROVIDED, CENTERED 3 + 1" ABOVE THE SURFACE MEASURED AT A RIGHT ANGLE TO COMPARTMENT DOOR 1N ITS CLOSED POSITION. OPERATED INDEPENDENTLY OF THE OTHER AND SHALL BE CONTROLLED SO THAT 1T OF THE RAMP. .CBC SEA., 11158.7.1.3 &FIG. 11 B-1 B. CAN BE OPERATED INDEPENDENTLY OF THE OTHER AND SHALL HAVE SWIVEL ANGLE 3. ABRUPT CHANGES 1N LEVEL ALONG ANY ACCESSIBLE ROUTE EXCEEDING 1 /2" SHALL COMPLY WITH THE REQUIREMENTS FOR CURB RAMPS. CBC SECTION 1023.4. CURB RAMPS 4. SANITARY FACILITY FIXTURES &ACCESSORIES ADJUSTMENTS, BOTH VERTICALLY AND HORIZONTALLY. ONE SHOWER HEAD SHALL BE LOCATED AT A HEIGHT OF 40 + 1" ABOVE THE FLOOR. CBC SEC 1505(C). 4. WHEN THE SLOPE IN THE DIRECTION OF TRAVEL OF ANY WALK EXCEEDS 1 VERTICAL TO 20 HORIZONTAL 1. CURB RAMPS SHALL BE A MINIMUM OF 4' IN WIDTH AND SHALL UE GENERALLY IN A A) THE HEIGHT OF ACCESSIBLE WATER CLOSETS SHALL BE A MINIMUM OF 17" AND J ENCLOSURES, WHEN PROVIDED FOR SHOWER STALLS, SHALL NOT OBSTRUCT TRANSFER ) IT SHALL COMPLY WITH THE PROVISIONS OF CBC SECTION 1007 AS A SINGLE SLOPED PLANE, WITH A MINIMUM OF SURFACE' WARPING AND CROSS SLOPE. A MAXIMUM OF 19" MEASURED TO THE TOP OF A MAXIMUM 2" HIGH TOILET SEAT, PEDESTRIAN RAMP. CBC SEC. 1023.3. CBC SEC. 11278.5.2. EXCEPT THAT 30 SEATS SHALL BE PERMITTED ONLY IN ALTERATIONS WHERE THE FROM WHEELCHAIRS ONTO SHOWER SEATS. CBC SEC. 11158.6.2.5. 5. WALK AND SIDEWALK SURFACE CROSS SLOPES SHALL NOT EXCEED 1/4 n PER FOOT. 2. THE SLOPE OF CURB RAMPS SHALL NOT EXCEED 1 VERTICAL TO 12 HORIZONTAL. EXISTING FIXTURE IS LESS THAN 15" HIGH. SEC. 1502 OF PLUMBING CODE. K) GLAZING USED IN DOORS AND PANELS OF SHOWER AND BATHTUB ENCLOSURES CBC SEC. 1023.1.3. CBC SEC. 11278.5,3. B) A CLEAR FLOOR SPACE 30 8Y 48" SHALL BE PROVIDED 1N FRONT OF A LAVATORY SHALL BE FULLY TEMPERED, LAMINATED SAFETY GLASS, OR APPROVED PLASTIC. WHEN GLASS 1S USED, IT SHALL HAVE A MINIMUM THICKNESS OF NOT LESS THAN 6, WALKS SHALL BE PROVIDED WITH A LEVEL AREA NOT LESS THAN 60" BY 60° AT A 3. MAXIMUM SLOPES OF ADJOINING GUTTERS, ROAD SURFACE IMMEDIATELY ADJACENT TO TO ALLOW A FORWARD APPROACH, SUCH CLEAR FLOOR SPACE SHALL ADJOIN OR OVERLAP AN ACCESSIBLE ROUTE SAND SHALL EXTEND INTO KNEE AND TOE SPACE WHEN FULLY TEMPERED, OR 1/4; WHEN LAMINATED, AND SHALL P 1/8 ASS THE ALL DOOR OR GATE THAT SWINGS TOWARD THE WALK, AND NOT LESS THAN 48" WIDE BY 44" THE CURB RAMP, OR ACCESSIBLE ROUTE, SHALL NO`r EXCEED 1:20 WITHIN 4' OF THE UNDERNEATH THE LAVATORY. CBC SEC. 1115B.9.1.1, TEST REQUIREMENTS UBC STANDARD N0, 24-2, CBC SEC. 11 ,8. DEEP AT A DOOR OR GATE: THAT SWINGS AWAY FROM THE WALK. CBC SEC 1023.1.3. TOP AND BOTTOM OF THE CURB RAMP. CBC SEC. 11278.5.3. C ) LAVATORIES SHALL BE MOUNTED WITH THE RIM OR COUNTER L) PLASTICS USED IN DOORS AND PANELS OF SHOWERS AND BATHTUB ENCLOSURES 7. WALKS SHALL EXTEND A MINIMUM OF 24" TO THE SIDE OF TH£ STRIKE EDGE OF A DOOR F 4. A LEVEL LANDING 4 DEEP SHALL BE PROVIDED AT THE UPPER END OF EACH CURB SURFACE NO HIGHER THAN 34" ABOVE THE FINISHED FLOOR AND WITH A CLEARANCE OF AT LEAST 29" SHALL BE OF A SHATTER -RESISTANT TYPE. CBC SEC. 1115B.9.9. OR GATE THAT SWINGS TOWARD THE WALK. CBC SEC. i RAMP OVER ITS FULL WIDTH TO PERMIT SAFE EGRESS FROM THE RAMP SURFACE, FROM THE FLOOR TO THE BOTTOM OF THE APRON WITH KNEE CLEARANCE UNDER M) AT LEAST ONE AND NOT LESS THAN 1 % OF ALL LOCKERS SHALL BE MADE 8. ALL WALKS WITH CONTINUOUS GRADIENTS SHALL HAVE LEVELS AREAS AT LEAST 5' IN THE SLOPE OF THE FANNED OR FLARED SIDES OF THE CURB RAMP SHALL NOT EXCEED 1 VERTICAL TO 12 HORIZONTAL. CBC SEC. 11278,5,4. THE FRONT UP EXTENDING A MINIMUM OF 30" IN WIDTH AND 8" MINIMUM DEPTH AT THE TOP. TOE CLEARANCE SHALL BE THE SAME, WIDTH AND SHALL BE A ACCESSIBLE TO PERSONS WITH DISABILITIES, INCLUDING CLEAR SPACE, REACH LENGTH AT INTERVALS OF AT LEAST EVERY 400. CBC SEC. 1023.6. MINIMUM OF 9" HIGH FROM THE FLOOR AND A MINIMUM OF 17" DEEP FROM THE RANGE REQUIREMENTS, AND A PATH OF TRAVEL NOT LESS THAN 36 IN CLEAR FRONT OF THE LAVATORY. CBC SEC. 1504(A)/ WIDTH TO THESE LOCKERS. CBC SEC. 1115B.6.4. 9. WALK AND SIDEWALK SURFACES SHALL BE SUP -RESISTANT AS FOLLOWS: 5. TRANSITIONS FROM RAMPS TO WALKS, GUTTERS, OR STREETS SHALL BE FLUSH AND FREE D) ALL PIPES UNDER LAVATORIES SHALL BE INSULATED OR OTHERWISE COVERED. ENTRANCES, EXITS, DOORS & AREAS FOR EVACUATION ASSISTANCE OF ABRUPT CHANGES, EXCEPT THAT THE LOWER END OF EACH CURB RAMP SHALL HAVE A SURFACE WITH A SLOP OF LESS THAN 6% GRADIENT SHALL BE AT LEAST AS 1 /2 LIP BEVELED AT 45 DEGREES. CBC SEC. 112'78.5.3 & 11278.5.5. THERE SHALL BE NO SHARP OR ABRASIVE SURFACES. UNDER LAVATORIES. SLOPE -RESISTANT AS THAT DESCRIBED AS A MEDIUM SALTED FINISH. CBC SEC. 1504(A). 1. ENTRANCES, EXITS & DOORS CBC SEC. 1023.1.1, 6. ALL CURB RAMPS SHALL HAVE A GROOVE BORDER 12 INCHES WIDE AT THE LEVEL OF THE SURFACE OF THE SIDEWALK ALONG THE TOP AND EACH SIDE. CBC SEC. 1127B.5.7, E) WHERE URINALS ARE PROVIDED, AT LEAST ONE SHALL HAVE A CLEAR FLOOR SPACE r A) LATCHING AND LOCKING DOORS THAT ARE HAND -ACTIVATED AND WHICH ARE IN A SURFACES WITH A SLOP OF 6% GRADIENT SHALL BE SUP RESISTANT. 30" BY 48" IN FRONT OF THE URINAL TO ALLOW FORWARD APPROACH. PATH OF TRAVEL SHALL BE OPERABLE WITH A SINGLE EFFORT BY LEVER TYPE CBC SEC 1023.1.2. 7. A CURB RAMP SHALL HAVE A DETECTABLE WARNING THAT EXTENDS THE FULL WIDTH CBC SEC. 1115B.9.4. HARDWARE, PANIC BARS, PUSH-PULL ACTIVATING BARS, OR OTHER HARDWARE AND DEPTH OF THE CURB RAMP INSIDE THE GROOVED BORDER WHEN THE RAMP SLOPE DESIGNED TO PROVIDE PASSAGE WITHOUT REQUIRING THE ABILITY TO GRASP 10. WALKS, SIDEWALKS, AND PEDESTRIAN WAYS SHALL BE FREE OF GRATINGS WHENEVER IS LESS THAN i VERTICAL TO 15 HORIZONTAL. DETECTABLE WARNINGS SHALL CONSIST F) CONTROLS FOR WATER CLOSET FLUSH VALVES SHALL BE MOUNTED ON THE WIDE THE OPENING HARDWARE. LOCKED EXIT DOORS SHALL OPERATE AS ABOVE IN POSSIBLE, FOR GRATINGS LOCATED IN THE SURFACE OF ANY OF THESE AREAS, GRID OF RAISED TRUNCATED DOMES WITH A DIAMETER OF NOMINAL 0.9 AT THE BASE SIDE OF TOILET AREAS. CBC SEC. 1502. EGRESS DIGRESSION. 'CBC SEC. 11338.2.5,1 OPENINGS IN GRATINGS SHALL BE NO GREATER THAN 1 /2" WIDE IN ONE DIRECTION. TAPERING TO 0.45" AT THE TOP, A HEIGHT OF NOMINAL 0.2", AND A " IF GRATINGS HAVE ELONGATED OPENINGS, THEY SHALL BE PLACED SO THAT THE LONG CENTER -TO -CENTER SPACING OF NOMINAL 2.35511 IN COMPLIANCE WITH CBC FIGURE 11 B-23B. G) WATER CLOSET AND URINAL FLUSH VALVE CONTROLS, AND FAUCET AND OPERATING B) HAND -ACTIVATED DOOR OPENING HARDWARE SHALL BE CENTERED BETWEEN 30 DIMENSION IS PERPENDICULAR TO THE DOMINANT DIRECTION OF TRAVEL. "NOMINAL", AS USED HERE SHALL BE IN ACCORDANCE WITH SECTION 12-31-102, MECHANISM CONTROLS, SHALL BE OPERABLE WITH ONE HAND, SHALL NOT REQUIRE AND 44 ABOVE THE FLOOR. CBC SEC, 1133B,2.5.1 CBC SEC. 1023.2 & FIG. 11 B-7B (A). STATE REFERENCED STANDARDS CODE. THE DETECTABLE WARNING SHALL CONTRAST TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST, AND SHALL BE MOUNTED C) THERE SHALL BE A LEVEL AND CLEARFLOOR OF LANDING ON EACH SIDE OF A VISUALLY WITH ADJOINING SURFACES EITHER LIGHT -ON -DARK OR DARK-ON-UGHT, NO MORE THAN 44" ABOVE THE FLOOR. CBC SEC. 1502, 1503(8), & 1504(C). ENTRANCES & EXITS THE MATERIAL USED TO PROVIDE CONTRAST SHALL BE AN INTEGRAL PART OF THE DOOR. THE LEVEL AREA SHALL HAVE A LENGTH IN THE DIRECTION OF DOOR WALKING SURFACE. THE DOMES MAY 8E CONSTRUCTED IN A VARIETY OF METHODS, H) THE FORCE REQUIRED TO ACTIVATE WATER CLOSET AND URINAL FLUSH VALVE SWING OF AT LEAST 60" AND THE LENGTH OPPOSITE THE DIRECTION OF DOOR 1 D ALL EXTERIOR EXITS SHALL 8E ACCESSIBLE IN CWITH ES NCBC INCLUDING C OR MAY BE PART OF A PREFABRICATED SURFACE CONTROLS, AND FAUCET AND OPERATING MECHANISM CONTROLS, SHALL HE NO SWING OF 48" AS MEASURED AT RIGHT ANGLE TO THE PLANE OF THE DOOR IN COMPLIANCEALL SECTION TREATMENT. CBC SEC�112078, RAMPED, GREATER THAN 5 LBF. CBC SEC. 1502, 1503 (C (8}, & 1504 . ) ITS CLOSED POSITION.,THE SLOPE OF THESE AREAS SHALL NOT EXCEED 2%. CBC SEC. 11338.2.4.2 & FIG. 118-26A & B. 2. ALL BUILDING ENTRANCES THAT ARE ACCESSIBLE SHALL BE IDENTIFIED WITH AT SANITARY FACILITIES 1) SELF -CLOSING FAUCET CONTROL VALVES ARE ALLOWED IF THE FAUCET REMAINS LEAST ONE STANDARD SIGN AND WITH ADDITIONAL DIRECTIONAL SIGNS AS REQUIRED OPEN FOR AT LEAST 10 SECONDS. CBC SEC. 1504(C), ) THE WIDTH OF THE LEVEL AREA ON THE SIDE TO WHICH THE DOOR SWINGS SHALL D17.5.7. TO BE VISIBLE TO PERSONS ALONG APPROACHING PEDESTRIAN WAYS. CBC SEC. 11� 1, GENERAL EXTEND A MINIMUM OF 24" PAST THE STRIKE EDGE OF THE DOOR FOR EXTERIOR J) WHERE TOWELS, SANITARY NAPKINS, WASTE RECEPTACLES, AND OTHER SIMILAR DOORS AND A MINIMUM OF 18" PAST THE STRIKE EDGE FOR INTERIOR DOORS. PARKING A DOORWAYS LEADING TO MEWS SANITARY FACILITIES SHAH BE IDENTIFIED BY } DISPENSING AND DISPOSAL FIXTURES ARE PROVIDED AT LEAST ONE OF EACH ADDITIONAL 12" 1S REQUIRED AT THE PUSH SIDE, IF DOOR 1S EQUIPPED WITH BOTH LATCH AND CLOSER. SEC. 11338.2.4.3 & FIG. 118-26A AN EQUILATERAL TRIANGLE 1/4" THICK WITH EDGES 12" LONG AND A VERTEX TYPE SHALL BE LOCATED WITH ALL OPERABLE PARTS, INCLUDING COIN SLOTS, . 1. ACCESSIBLE PARKING SPACES SERVING A PARTICULAR BUILDING SHALL BE LOCATED POINTING UPWARD. WOMEN'S SANITARY FACILITIES SHALL BE IDENTIFIED BY WITHIN 40n FROM THE FINISHED FLOOR. CBC SEC. 11159.9.2. ON THE SHORTEST ACCESSIBLE ROUTE OF TRAVEL FROM ADJACENT PARKING TO A PRIMARY A CIRCLE 1/4 THICK AND 12 IN DIAMETER, CBC SEC. 1115B.5. K) TOILET DISPENSERS SHALL BE LOCATED ON THE WALL WITHIN ) E THE FLOOR OR LANDING SHALL BE NOT MORE THAN 1 2" LOWER THAN THE FIG. ENTRANCE. CBC SEC. 11298.1. TISSUE 12" OF THRESHOLD OF THE DOORWAY. SEC, 1133B.2.4.1 & 118-32. B) UNISEX SANITARY FACILITIES SHALL BE IDENTIFIED BY A CIRCLE 1/4" THICK, THE FRONT EDGE OF THE TOILET SEAT AND NO LOWER THAN 19" FROM THE FLOOR. 2. IN EACH PARKING AREA, A BUMPER OR CURB SHALL BE PROVIDED AND LOCATED TO 12" DIAMETER, WITH A 1/4" THICK TRIANGLE SUPERIMPOSED ON THE CIRCLE DISPENSERS THAT CONTROL DELIVERY OR THAT DO NOT PERMIT CONTINUOUS PAPER F) THE BOTTOM 10" OF ALL DOORS EXCEPT AUTOMATIC AND SLIDING SHALL HAVE PREVENT ENCROACHMENT OF CARS OVER THE REQUIRED WIDTH OF WALKWAYS. AND WITHIN THE 12" DIAMETER. CBC SEC. 11158.5' FLOW SHALL NOT BE USED, CBC SEC. 11158.9.3 & FIG. 118-1A. A SMOOTH, UNINTERRUPTED SURFACE TO ALLOW THE DOOR TO BE OPENED BY CBC SEC. 1129B.4,3. A WHEELCHAIR FOOTREST WITHOUT CREATING A TRAP OR HAZARDOUS CONDITION, C) GEOMETRIC (CIRCLE AND TRIANGLE) SYMBOLS ON SANITARY FACILITY DOORS L ) TOILET ROOM FLOORS SHALL HAVE A SMOOTH HARD, NONABSORBENT SURFACE SUCH CBC SEC. 11338.2.6 & FIG 118-29. , 3. PEDESTRIAN WAYS WHICH ARE ACCESSIBLE TO PEOPLE WITH DISABILITIES SHALL BE PROVIDED FROM EACH SUCH PARKING SPACE TO RELATED FACILITIES, SHALL BE CENTERED ON THE DOOR AT A HEIGHT OF 60" AND THEIR COLOR AND A5 PORTLAND CEMENT, CONCRETE, CERAMIC TILE OR OTHER APPROVED MATERIAL WHICH EXTENDS UPWARD ONTO THE WALK MINIMUM 5", WALLS WITHIN WATER G) RECESSED DOORMATS SHALL BE ADEQUATELY ANCHORED TO PREVENT INTERFERENCE INCLUDING CONTRAST SHALL BE DISTINCTLY DIFFERENT T"ROM THE COLOR AND CONTRAST CLOSET COMPARTMENTS AND WALLS WITHIN 24 OF THE FRONT AND CURBS CUTS OR RAMPS AS NEEDED. CBC SEC. 11298.4.3. OF THE DOOR. CBC SEC. 1115B.5. SIDES OF WITH WHEELCHAIR TRAFFIC, SEC. 1133B.1.1.1.3 & FIG. 118-25. URINALS SHALL BE SIMILARLY FINISHED TO A HEIGHT OF 48" AND, EXCEPT FOR 4. RAMPS SHALL NOT ENCROACH INTO ANY PARKING SPACE, WITH THE EXCEPTION OF A D) ADDITIONAL SIGNAGE REQUIREMENTS: RAISED LETTERS SHALL BE PROVIDED AND STRUCTURAL ELEMENTS, THE MATERIALS USED IN SUCH WALLS SHALL BE A TYPE H) MAXIMUM EFFORT TO OPERATE DOORS SHALL NOT EXCEED 8-1/2 POUNDS FOR TRANSITION RAMP FROM A LOADING/UNLOADING AREA TO AN ADJACENT SIDEWALK. SHALL BE ACCOMPANIED BY BRAILLE IN CONFORMANCE WITH SECTION 1117B.5.6. WHICH IS NOT ADVERSELY AFFECTED BY MOISTURE, CBC SEC, 11158.9.4. EXTERIOR DOORS, AND 5 POUNDS FOR INTERIOR DOORS, SUCH PULL OR PUSH THE TRANSITION RAMP SHALL BE A MINIMUM OF 48" IN WIDTH, A MAXIMUM OF 60" THEY SHALL BE INSTALLED ON THE WALL ADJACENT TO THE LATCH OUTSIDE OF THE EFFORT BEING APPLIED AT RIGHT ANGLES TO HINGED DOORS AND AT THE CENTER IN LENGTH, WITH A MAXIMUM SLOPE OF 1:12. CBC SEC. 1129B.4.3 & FIG, 118-18A DOOR. WHERE THERE IS NO WALL SPACE ON THE LATCH SIDE, INCLUDING AT 5. GRAB BARS PLANE OF SLIDING OR FOLDING DOORS, COMPENSATING DEVICES OR AUTOMATIC THROUGH C. DOUBLE LEAF DOORS, SIGNS SHALL BE PLACED ON THE NEAREST ADJACENT WALL, DOOR OPERATORS MAY BE UTILIZED TO MEET THE ABOVE STANDARDS, WHEN PREFERABLE ON THE RIGHT. MOUNTING HEIGHT SHALL BE 60 INCHES ABOVE THE A) GRAB BARS SHALL BE SECURELY ATTACHED 33" ABOVE AND PARALLEL TO THE FIRE DOORS ARE REQUIRED, THE MAXIMUM EFFORT TO OPERATE THE DOOR MAY 5. ACCESSIBLE PARKING SPACES SHALL BE SO LOCATED THAT PERSONS WITH DISABILITIES FINISH FLOOR TO THE CENTER LINE OF THE SIGN. MOUNTING LOCATION SHALL BE FLOOR, EXCEPT THAT WHERE A TANK -TYPE TOILET IS USED WHICH OBSTRUCTS BE INCREASED TO MAXIMUM ALLOWABLE BY THE APPROPRIATE ADMINISTRATIVE ARE NOT COMPELLED TO WHEEL OR WALK BEHIND PARKED CARS OTHER THAN THEIR OWN. DETERMINED SO THAT A PERSON MAY APPROACH WITHIN 3 INCHES OF SIGNAGE PLACEMENT AT 33", THE GRAB BAR MAY BE AS HIGH AS 36 CBC CBC SEC. 11158.8.1 AUTHORITY, NOT TO EXCEED 15 POUNDS. SEC. 11338.2.5 CBC SEC. 11298.4.3. WITHOUT ENCOUNTERING PROTRUDING OBJECTS OR STANDING WITHIN THE SWING & FIG. 118-iA THROUGH 118-1C. OF A DOOR. CBC SEC. 1117B.5.9. STAIRWAYS 6. SIGNS TO IDENTIFY ACCESSIBLE PARKING SPACES MAY BE CENTERED ON A WALL AT THE B) THE DIAMETER OR WIDTH OF THE GRIPPING SURFACES OF A GRAB BAR SHALL BE INTERIOR END OF THE PARKING SPACE AT A MINIMUM HEIGHT OF 36" FROM THE PARKING 2. SINGLE ACCOMMODATION SANITARY FACILITIES 1-1/4- TO 1-1/2" OR THE SHAPE SHALL PROVIDE AN EQUIVALENT GRIPPING 1, WHERE THE EXTENSION OF THE HANDRAIL IN THE DIRECTION OF THE STAIR RUN WOULD SPACE FINISHED GRADE, GROUND OR SIDEWALK. CBC SEC. 1129B.5. SURFACE. IF GRAB BARS ARE MOUNTED ADJACENT TO A WALL, THE SPACE CREATE A HAZARD, THE TERMINATION OF THE EXTENSION SHALL BE MADE EITHER 7. AN ADDITIONAL SIGN SHALL ALSO BE POSTED, IN A CONSPICUOUS PLACE, AT EACH NOTE: SINGLE ACCOMMODATION SANITARY FACILITY IS DEFINED AS " A ROOM THAT HAS BETWEEN THE WALL AND THE GRAB BARS SHALL BE 1-1/2 CBC SEC. 11158.8.2 & FIG. 118-1 C. ROUNDED OR RETURNED SMOOTHLY TO THE FLOOR, WALL, OR POST. WHERE THE STAIRS ENTRANCE TO OFF-STREET PARKING FACILITIES, OR IMMEDIATELY ADJACENT TO AND NOT MORE THAT ONE OF EACH TYPE OF SANITARY FIXTURE, IS INTENDED FOR USE BY ARE CONTINUOUS FROM LANDING TO LANDING, THE INNER RAIL SHALL BE CONTINUOUS VISIBLE FROM EACH STALL OR SPACE. THE SIGN SHALL BE NOT LESS THAN 17" X 22" ONLY ONE PERSON AT A TIME HAS NO PARTITION AROUND THE TOILET AND HAS A DOOR THAT CAN BE LOCKED ON THE INSIDE BY THE ROOM OCCUPANT." CBC SEC. 220.12. C) THE STRUCTURAL STRENGTH OF GRAB BARS, TUB AND SHOWER SEATS, FASTENERS, AND NEED NOT EXTEND OUT INTO THE LANDING. CBC SEC. 1006,9.2.4A & FIG. 118-37. 1N SIZE WITH LETTERING NOT LESS THAN 1" IN HEIGHT, WHICH CLEARLY AND AND MOUNTING DEVICES SHALL MEET THE SPECIFICATIONS OF CBC SEC. 11158.8.3. 2. HANDRAILS PROJECTING FROM A WALL SHALL HAVE A SPACE OF 1-1/2" BETWEEN THE CONSPICUOUSLY STATES THE; FOLLOWING: A) THERE SHALL BE IN THE ROOM A CLEAR FLOOR SPACE OF AT LEAST 60" IN 0) THE GRAB BAR AND ANY WALL OR OTHER SURFACE ADJACENT TO IT WALL AND HANDRAIL. CBC SEC. 1006.9.2.5A & FIG. 11 B-36. "UNAUTHORIZED DIAMETER, OR A T-SHAPED SPACE COMPLYING WITH FIGURES 118-12(A) SHALL BE FREE VEHICLES PARKED IN DESIGNATED ACCESSIBLE SPACES NOT AND (8). NO DOOR SHALL ENCROACH INTO THIS SPACE. CBC SEC. 1115B.7.2 OF ANY SHARP OR ABRASIVE ELEMENTS. EDGES SHALL HAVE A MINIMUM RADIUS 3. THE UPPER APPROACH AND THE LOWER TREAD OF EACH INTERIOR STAIR SHALL BEMARKED DISPLAYING DISTINGUISHING PLACARDS OR LICENSE PLATES ISSUED FOR & FIG. 118-1A. OF 1/8". CBC SEC. 1115B.8.4. BY A STRIP OF CLEARLY CONTRASTING COLOR AT LEAST 2 AND NO MORE THAN 4" WIDE PERSONS WITH DISABILITIES MAY BE TOWED AWAY AT OWNER'S EXPENSE. AND PLACED PARALLEL TO AND NOT MORE THAN 1" FROM THE NOSE OF THE STEP OR TOWED VEHICLES MAY BE RECLAIMED AT OR 8Y TELEPHONING " B) THE WATER CLOSET SHALL BE LOCATED IN A SPACE WHICH PROVIDES A MINIMUM 6. BATHING FACILITIES & LOCKERS LANDING TO ALERT THE VISUALLY IMPAIRED. THE STRIP SHALL BE OF A MATERIAL _ 28" WIDE CLEAR SPACE FORM A FIXTURE OR A MINIMUM 32" WIDE CLEAR SPACE THAT IS AT LEAST AS SLIP -RESISTANT AS THE OTHER TREADS OF THE STAIR. NOTE: BLANK SPACES ARE TO 8E FILLED IN WITH APPROPRIATE INFORMATION AS A FROM A WALL AT ONE SIDE. THE OTHER SIDE SHALL PROVIDE 18" FROM THE A) COMPARTMENT SHOWERS SHALL BE 42" IN WIDTH BETWEEN WALL SURFACES AND A PAINTED STRIP SHALL BE ACCEPTABLE. CBC SEC. 1006.16.1 & FIG. 11 B-35. PERMANENT PART OF THE SIGN. CENTER LINE OF THE WATER CLOSET TO THE WALL. A MINIMUM 48" CLEAR SPACE 48" IN DEPTH WITH AN ENTRANCE OPENING WIDTH OF 36" MINIMUM. SHALL BE PROVIDED 1N FRONT OF THE WATER CLOSET. CBC SEC. 11158.7.2 & CBC SEC. 1115B.6,2.1. 4. WHERE STAIRWAYS OCCUR OUTSIDE A BUILDING, THE UPPER APPROACH AND ALL TREADS PEDESTRIAN RAMPS FIG. 118-1A. SHALL BE MARKED BY A STRIP OF CLEARLY CONTRASTING COLOR AT LEAST 2" AND NO 8) THRESHOLDS OR RECESSED DROPS AT COMPARTMENT SHOWERS SHALL BE A MAXIMUM MORE THAN 4" WIDE AND PLACED PARALLEL TO AND NOT MORE THAN 1" FROM THE NOSE 3. MULTIPLE ACCOMMODATION SANITARY FACILITIES OF 1/2" IN HEIGHT AND SHALL BE BEVELED OR SLOPED AT AN ANGLE NOT OF THE STEP OR LANDING TO ALERT THE VISUALLY IMPAIRED. THE STRIP SHALL BE NOTE: ANY PATH OF TRAVEL SHALL BE CONSIDERED A RAMP IF ITS SLOPE IS GREATER EXCEEDING 45 DEGREES FROM THE HORIZONTAL. CBC SEC. 1115B.6.2.2. OF A MATERIAL THAT IS AT LEAST AS SUP -RESISTANT AS THE OTHER TREADS OF THE THAN 1' RISE IN 20' OF HORIZONTAL RUN. CBC SEC. 1007.1A. NOTE: MULTIPLE ACCOMMODATION SANITARY FACILITY IS DEFINED AS " A ROOM THAT STAIR. A PAINTED STRIP SHALL BE ACCEPTABLE. CBC SEC. 1006.16.1 & FIG. 11 B-35. 1. THE MAXIMUM SLOPE OF A P THAT SERVES ANY EXIT WAY, PROVIDES! ACCESS FOR HAS MORE THAN ONE SANITARY FIXTURE 1S INTENDED FOR THE USE OF MORE THAN ONE PERSON AT A TIME, AND WHICH USUALLY IS PROVIDED WITH PRIVACY COMPARTMENTS OR C) COMPARTMENT SHOWER FLOORS SHALL SLOPE TOWARD THE REAR TO A DRAIN LOCATED WITHIN 6" OF THE REAR WALL, WITH A MAXIMUM FLOOR SLOPE OF 1/2" 5. ALL TREAD SURFACES SHALL BE SUP -RESISTANT. TREADS SHALL HAVE SMOOTH, PERSONS WITH DISABILITIES, OR IS IN THE PATH OF TRAVEL SHALL BE 1 RISE IN SCREENS SHIELDING SOME FIXTURES FROM VIEW." CBC SEC. 214.13. PER FOOT IN ANY DIRECTION. THE FLOOR SURFACES SHALL BE OF CARBORUNDUM ROUNDED, OR CHAMFERED, EXPOSED EDGES, AND NO ABRUPT EDGES AT THE NOSING 12' OF HORIZONTAL RUN. CBC SEC. 1007.3A. OR GRIT -FACED TILE OR OF MATERIAL PROVIDING EQUIVALENT SUP -RESISTANCE. (FRONT EDGE). CBC SEC. 1006.16.2.1. 2. THE CROSS SLOPE OF RAMP SURFACES SHALL BE NO GREATER THAN 1:50. A) A CLEAR SPACE MEASURED FORM THE FLOOR TO A HEIGHT OF 27" ABOVE THE FLOOR, WITHIN THE SANITARY FACILITY ROOM, OF SUFFICIENT SIZE TO INSCRIBE A CBC SEC. 11158.6.2.3, 6. THE NOSING SHALL NOT PROJECT MORE THAN 1-1/2" PAST THE FACE OF THE RISER CBC SEC. 1007.3,1A. CIRCLE WITH A DIAMETER NOT LESS THAN 60", OR CLEAR SPACE 56" BY 63" 1N D) THE FOLLOWING COMPARTMENT SHOWER ACCESSORIES SHALL 8E PROVIDED: BELOW. CBC SEC. 1006.16.2.2 & FIG. 11 B-35. 3. DOORS IN ANY POSITION SHALL NOT REDUCE THE MINIMUM DIMENSION OF THE RAMP SIZE, SHALL BE PROVIDED FOR WHEELCHAIR MANEUVERING. DOORS OTHER THAN CBC SEC. 11158,6.2.4 AND FIG, 118-2A. LANDING TO LESS THAN 42 AND SHALL NOT REDUCE THE REQUIRED WIDTH BY MORE THAN 3" WHEN FULLY OPEN. CBC SEC. 1007.4.3A & FIG. 118-39. THE DOOR TO THE ACCESSIBLE TOILET COMPARTMENT IN ANY POSITION MAY " ENCROACH INTO THIS SPACE BY NOT MORE THAN 12 . CBC SEC. 11158.7.1.1 & G, 1 B 18. " i) A FOLDING SEAT 18 IN WIDTH AND A MINIMUM OF 3fi�_ IN LENGTH LOCATED ON THE WALL OPPOSITE CONTROLS AND MOUNTED 18" ABOVE THE BATHROOM FLOOR.0 1 B lO it a E' IL FIANMG le DIMN 015 RLDBU aVla M HUIt+DIHQr H2012 Isu C COSTA IMSA, CAT `OWU 026" 714.438.36S4 W � CN ® W �--- C!>]cty w ( ) a V W -- LU F_ 0 `2 ui r? Z F u Qf Q . • 0 < W Sy Lo k' THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN AS AN INSTRUMENT OF PROFESSIONAL SERVICE IS THE PROPERTY OF " BOLE' INTERNATIONAL AND IS NOT TO BE USED IN WHOLE OR PART FOR ANY PROJECT OTHER THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION OF BOLE INTERNATIONAL. THIS DOCUMENT SHALL NOT BE REPRODUCED OR MODIFIED IN ANYWAY WITHOUT THE EXPRESSED WRITTEN CONSENT OF BOLE' INTERNATIONAL. REVISIONS: Q912103 - PROJECT START 9/5/03 -CITY SUBMITTAL 9/29/03 - CITY REVISIONS © 101I103 - CITY RESUBMI TTAL Q PARTICIPANTS DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED BY: J.A. USABLE: +I- 4,503 U.S.F. RENTABLE: PROJECT: JOB: OBSIDIAN ENT. DATE: SCALE: AS NOTED ., SHEET NAME Nr TITLE 24 NOTES SHEET T1.2 Y DEMOLITION PLAN GENERAL NOTES: 1. PATCH, REPAIR & REFINISH WALL SURFACES TO REMAIN AS REQ'D. 2. REMOVE PARTITION, MILLWORK AND PLUMBING AS INDICATED GENERAL CONTRACTOR TO VERIFY PAR1111ON TYPES TO BE DEMOLISHED (SLAB TO SLAB, FLOOR TO CEILING, DEMONTABLE, ETC,.) SEE DEMOL 110N PARTITION SCHEDULE FOR MORE INFORMATION. 3. REFER TO CONSTRUC11ON PLAN FOR EXTENT OF DEMOLITION. 4. GENERAL CONTRACTOR TO VERIFY IF ANY DEMOLISHED WALL OR COLUMN FURRINGS CONTAIN MECHANICAL OR PLUMBING & ADVICE BOLE INTNL. 5. SAVE AND STORE ALL LIGHT FIXTURES, EXIT SIGNS, DOORS & HARDWARE FOR RE --USE U.O.N. 6. ALL ADJACENT SURFACES DAMAGED DURING DEMOL111ON TO BE PATCHED AND REPAIRED AND PREPARED FOR NEW FINISHES. REMOVE AND REPLACE DAMAGED CEILING TILES AND GRID TO MATCH EXISTING U.O.N. 7. REMOVE ALL TELEPHONE, ELECTRICAL AND DATA OUTLETS, FIXTURES, PANELS, ETC. FROM ALL DEMOLISHED PARTITIONS. REMOVE ALL CORRESPONDING CABLES, CONDUIT, WRING, ETC. ALL THE WAY BACK TO THE ORIGINAL SOURCE AT MAIN FLOOR TELEPHONE OR ELECTRICAL ROOMS. 8. REMOVE ALL FLOOR & WALL FINISHES INCLUDING CERAMIC TILE W/ SET11NG BED, CLEAN & PREP FLOORS FOR NEW FINISHES. EXCEPT FOR EXISTING RESTROOMS, U.O.N. 9. REMOVE SURFACE MOUNTED ACCESSORIES / DISPENSERS. PATCH AND PREPARE WALLS FOR NEW FINISH. 10. REMOVE ALL THERMOSTATS FOR REUSE AND RELOCATION. 11. REMOVE ALL NAMEPLATES / TAGS ON SIDELIGHTS, DOORS AND WALLS. PATCH AND PREPARE AS REQUIRED FOR NEW FINISH. 12. ALL EXISTING EXIT LIGHTS TO BE REUSED AND RELOCATED AS REQUIRED FOR CODE COMPLIANCE. 13. ALL EXISTING LIGHT SENSORS TO BE REUSED AND RELOCATED AS REQUIRED FOR NEW LAYOUT. PARTITION PLAN NOTES 1. THE "GENERAL CONDITIONS OF THE CONTRACT FOR CONSTRUCTION" A201, 1991 EDITION OF THE AMERICAN INSTITUTION OF ARCHITECTS AS MODIFIED AND AS MADE A PART OF THE GENERAL CONTRACTOR CONTRACT WITH OWNER. 2• "ARCHITECT" AS USED IN THESE DOCUMENTS REFER TO: BOLE' INTERNATIONAL 2915 REDHILL AVENUE BUILDING 8201, SUITE C COSTA MESA, CALIFORNIA 92628 PHONE: 714.438.3834 3. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ALL APPLICABLE CODES, REGULATIONS AND ORDINANCES HAVING JURISDICTION. 4. CONTRACTOR FOR THE PROJECT SHALL BE RESPONSIBLE FOR OBTAINING ALL REQUIRED BUILDING PERMITS. 5. CONTRACTOR IS RESPONSIBLE FOR EXAMINING ALL CONTRACT DOCUMENTS, FIELD CONDITIONS, AND CONFIRMING THAT WORK IS BUILDABLE AS SHOWN BEFORE PROCEEDING WITH CONSTRUCTION. IF THERE ARE ANY QUESTIONS REGARDING THESE OR OTHER COORDINATION ITEMS, THE CONTRACTOR IS RESPONSIBLE FOR OBTAINING A CLARIFICATION FROM THE ARCHITECT BEFORE PROCEEDING WITH WORK IN QUESTION. 6. INSTALL ALL MANUFACTURED ITEMS, MATERIALS AND EQUIPMENT IN STRICT ACCORDANCE WITH THE MANUFACTURER'S SPECIFICATIONS. 7. CONTRACTOR SHALL SUBMIT CONFIRMATIONS OF DELIVERY DATES FOR ORDERS OF MATERIAL AND EQUIPMENT IN STRICT ACCORDANCE WITH THE MANUFACTURER'S SPECIFICATIONS. 8. THE CONTRACTOR SHALL SUBMIT ONE BLUEPRINT SET & ONE SEPIA SET OF SHOP DRAWINGS INCLUDING DETAILED FABRICATION AND ERECTION DRAWINGS. SETTING DRAWINGS, DIAGRAMMATIC DRAWINGS AND MATERIAL SCHEDULES, LOCATION AND ORIENTATION OF ALL ITEMS SHALL BE CLEARLY INDICATED. COMMENCE FABRICATION OF SHOP ITEMS ONLY AFTER RECEIVING ARCHITECTS APPROVAL:.. 9. ALL REQUESTS FOR SUBSTITUTION OF ITEMS SPECIFIED SHALL BE SUBMITTED IN WRITING AND WILL BE CONSIDERED ONLY IF, A MORE ADVANTAGEOUS DELIVERY DATE OR A LOWER PRICE WITH CREDIT TO THE TENANT WILL. BE PROVIDED WITHOUT SACRIFICING QUALITY, APPEARANCE AND FUNCTION. UNDER NO CIRCUMSTANCES WILL ARCHITECT BE REQUIRED TO PROVE THAT A PRODUCT PROPOSED FOR SUBSTITUTION IS OR IS NOT OF EQUAL QUALITY TO THE PRODUCT SPECIFIED. 10. ALL WORK NOTED "N.I.C." OR "NOT IN CONTRACT" IS TO BE ACCOMPLISHED BY A CONTRACTOR OTHER THAN THE GENERAL CONTRACTOR AND IS NOT TO BE PART OF THE CONSTRUCTION AGREEMENT. THE GENERAL CONTRACTOR SHALL COORDINATE WITH "OTHER" CONTRACTOR PER REQUIREMENTS ESTABLISHED BY OWNER & TENANT. 11 • "ALIGN" AS USED IN THESE DOCUMENTS SHALL MEAN TO ACCURATELY LOCATE FINISH FACES IN THE SAME PLACE. 12. "TYPICAL" AS USED IN THESE DOCUMENTS SHALL MEAN THAT THE CONDITION IS THE SAME OR REPRESENTATIVE FOR ALL SIMILAR CONDITIONS THROUGHOUT, UNLESS OTHERWISE NOTED. 13. DETAILS ATE USUALLY KEYED AND NOTED "TYPICAL" ONLY ONCE, WHEN THEY FIRST OCCUR AND ARE REPRESENTATIVE OF ALL, SIMILAR CONDITIONS THROUGHOUT, UNLESS OTHERWISE NOTED. 14. COLUMN CENTERLINES (GRID LINES) ARE SHOWN FOR DIMENSIONING PURPOSES. 15. ALL VERTICAL DIMENSIONS SHOWN ARE TO FLOOR SLAB, UNLESS OTHERWISE NOTED. 16. DO NOT SCALE DRAWINGS. DIMENSIONS GOVERN. LARGE SCALE DETAILS GOVERN OVER SMALL SCALE DETAILS. 17. CONTRACTORS SHALL BE RESPONSIBLE FOR THE GENERAL CLEANING OF A JOB AFTER ITS COMPLETION CLEANING SHALL INCLUDE THE INTERIOR OF THE BUILDING AND THE PATH OF TRAVEL TO THE JOB SITE AND SHALL INCLUDE THE PARKING LOTS, ELEVATORS, LOBBIES, AND CORRIDOR CARPET. 18. CONTRACTOR SHALL BE RESPONSIBLE FOR BLOCKING OFF SUPPLY AND RETURN AIR GRILLES, DIFFUSERS & DUCTS TO KEEP DUST FROM ENTERING INTO THE BUILDING AIR DISTRIBUTION SYSTEMS. 19. CONTRACTOR AND ARCHITECT TO REVIEW & APPROVE CHALK LINES OF PARTITION LAYOUT PRIOR TO COMMENCEMENT OF PARTITION CONSTRUCTION. 20. ALL DIMENSIONS ARE TO FINISH FACE OF WALL, U.N.O. 21 • DOOR OPENINGS IN PARTITIONS NOT DIMENSIONED ARE TO BE LOCATED 4" FROM ADJACENT PARTITIONS. 22. ALL INTERIOR PARTITIONS SHALL BE TAPED AND SANDED SMOOTH TO RECEIVE PAINT OR WALL COVERING. 23. USE WATER RESISTANT GYPSUM BOARD AT ALL AREAS SUBJECT TO MOISTURE OF WHERE TILE IS USED. 24. PREPARE ALL FLOOR AND WALLS AS REQUIRED TO RECEIVE NEW FINISHES. 25. CONTRACTOR TO FURNISH & INSTALL 16 GAUGE GALVANIZED METAL WALL BACKING AT ALL BUILT-IN MILLWORK LOCATIONS, HANGING WALL EQUIPMENT. ETC. VERIFY EXACT LOCATIONS WITH MILLWORK & ACCESSORY CONTRACTORS. 26. VERIFY ALL APPLIANCE & EQUIPMENT REQUIREMENTS WITH MANUFACTURERS. PROVIDE ALL NECESSARY WALL BACKING, BRACING, ELECTRICAL & PLUMBING SUPPLY, FITTINGS & CONNECTORS TO SUPPORT OR COMPLETE INSTALLATION. SUPPLY CATALOG CUT SHEETS FOR ARCHITECT'S APPROVAL. 27. FIELD MEASURE AS REQUIRED FOR ALL GLAZING AND MILLWORK CONDITIONS PRIOR TO FABRICATION. 28. ALL PENETRATIONS AT RATED CONSTRUCTIONS SHALL. BE PROTECTED TO MAINTAIN RATING. 29. CONTRACTOR SHALL USE 3 5/8" METAL STUDS MINIMUM AT ALL PLUMBING WALLS. CONTRACTOR TO VERIFY ACTUAL DEPTH REQUIRED, ANY DISCREPANCIES SHALL BE REPORTED TO THE ARCHITECT. 30. ALL HOT WATER LINES SHALL BE PROPERLY INSULATED. SEE PLUMBING DRAWINGS. 31. ALL PLUMBING WORK SHALL BE IN ACCORDANCE WITH LOCAL AND NATIONAL CODES. 32. ALL MILLWORK SHALL CONFORM TO W.I.C. CUSTOM STANDARDS. 33. EXACT LOCATION OF FIRE EXTINGUISHER, CABINETS TO BE CONFIRMED WITH ARCHITECT BEFORE INSTALLATION. PROVIDE ADDITIONAL FIRE EXTINGUISHERS 7 CABINET AS REQUIRED BY THE FIRE DEPARTMENT FIELD INSPECTORS. 34. CONTRACTOR TO VERIFY LOCATION OF ALL THERMOSTATS WITH ARCHITECT PRIOR TO INSTALLATION. 35. EXISTING FIRE HOSES TO REMAIN. POWER & SIGNAL GENERAL NOTES 1. PROVIDE ONE -HOUR FIRE PROTECTION AT ALL OUTLETS AND SWITCHES LOCATED IN ONE -HOUR RATED PARTITIONS. 2. ALL TELEPHONE AND DATA CABLE TO BE TEFLON COATED PLENUM RATED CABLE, SUPPORTED INDEPENDENTLY FROM SUSPENDED CEILING SYSTEM. CABLING TO BE SUPPLIED BY TENANT, ALL PULLS AND TERMINATIONS BY GENERAL. CONTRACTOR. 3. ALL SEPARATE CIRCUITS RECEPTACLES TO BE ORANGE COLOR WITH BUILDING STANDARDS COLOR COVER PLATE. 4. ALL NEW WALL MOUNTED OUTLETS TO BE CENTERED AT +18A A.F.F., U.N.O. 5. ALL OUTLETS TO BE INSTALLED AT LOCATIONS SHOWN BY DIMENSIONS ON THE POWER & SIGNAL PLAN. DIMENSION ALL OUTLETS FROM THE CENTERLINE OF THE OUTLET BOX. NON -DIMENSIONED OUTLETS ARE TO BE LOCATED AT THE NEAREST WALL STUD. 6. WHEN OUTLETS ARE GROUPED TOGETHER (2 OR MORE), THEY ARE TO BE SPACED NO MORE THAN 2" APART. 7• COORDINATE TELEPHONE/DATA INSTALLATION WITH APPROPRIATE SUBCONTRACTOR 8. WHERE ELECTRICAL WORK IS SPECIFIED IN CONJUNCTION WITH CABINET WORK, LAMPS AND FIXTURES ARE TO BE PROVIDED BY THE GENERAL CONTRACTOR. 9. CUT OUT FOR SWITCHES, OUTLETS, ETC. AS REQUIRED BY THE CABINET CONTRACTOR ARE TO BE COORDINATES WITH THE ELECTRICAL CONTRACTOR, U.N.Q. ALL RECEPTACLES WHERE MILLWORK OCCURS SHALL BE LOCATED PER ELEVATIONS OF THE MILLWORK ITEM IN QUESTION. 10. ALL WALL COVER PLATES SHALL BE WHITE, UNLESS BUILDING STANDARDS IS DIFFERENT, MATCH BUILDING STANDARDS. CUT OUTS FOR SWITCHES, OUTLETS, ETC. AS REQUIRED BY THE CABINET CONTRACTOR ARE TO BE COORDINATED WITH THE ELECTRICAL CONTRACTOR, U.N.O. ALL RECEPTACLE WHERE MILLWORK OCCURS SHALL BE LOCATED PER ELEVATIONS OF THE MILLWORK ITEM IN QUESTION. 11. LOCATIONS OF FURNITURE POWER FEEDS SHALL ACCOMMODATE CIRCUITS & WIRE PER ELECTRICAL DRAWINGS. TENANT SHALL BE RESPONSIBLE FOR PROVIDING FURNITURE POWER FEED, GENERAL CONTRACTOR SHALL INSTALL THE POWER FEED. 12. WHERE DEDICATED ELECTRICAL OUTLETS ARE NOTED WITHIN THE FURNITURE PANEL SYSTEM, THE PANEL SYSTEM SHALL ACCOMMODATE THIS REQUIREMENT. 13. ALL EXISTING ELECTRICAL DEVICES ARE TO REMAIN UNLESS OTHERWISE NOTED. 14. FIRE LIFE SAFETY: PROVIDE LAYOUT THAT ALIGNS WITH LIGHT FIXTURES. REFLECTED CEILING GENERAL NOTES 1. NO COMBUSTIBLE MATERIALS SHALL BE USED IN THE PLENUM SPACE, INCLUDING ALUMINUM FLEX, ALUMINUM CONDUIT, AND POT METAL CONNECTORS. 2. ALL JUNCTIONS BOXES AND MECHANICAL EQUIPMENT REQUIRING ACCESS FOR SERVICE SHALL BE LOCATED OVER ACOUSTICAL CEILING. NO ACCESS HATCHES SHALL BE INSTALLED IN THE GYPSUM BOARD CEILING WITHOUT PRIOR APPROVAL BY ARCHITECT. (NO EXCEPTION) 3. LOCATE RECESSED DOWN LIGHTS, WALL WASHERS, SMOKE DETECTORS, EXIT SIGNS, SPEAKERS, ETC. IN CENTER OF 24"X24" PORTION OF 24"X48" CEILING TILES, U.N.O. 4. ALL NEW FLUORESCENT LAMPS WILL BE BUILDING STANDARDS, SAME COLOR AND MANUFACTURER. 5. PROVIDE SWITCHES AND LIGHT SENSORS FOR OPEN AREAS . AND PRIVATE OFFICES. ACTUAL LOCATION OF ALL SWITCHES TO BE DETERMINED BY ELECTRICAL ENGINEER. 6. PLACEMENT OF LIGHT FIXTURES IN AREAS WHERE MAIN DUCTS MAY CAUSE INTERFERENCE MUST BE APPROVED BY ARCHITECT PRIOR TO INSTALLATION. 7. FIELD VERIFY ALL CLEARANCES OF DUCTS, PIPES, SPRINKLERS, ETC., AND NOTIFY ARCHITECT OF ANY CONFLICTS PRIOR TO INSTALLATION OF LIGHTS, ETC. 8. NOTIFY ARCHITECT OF ANY DISCREPANCIES BETWEEN ARCHITECTURAL AND ENGINEERING DRAWINGS AND OBTAIN CLARIFICATION BEFORE PROCEEDING WITH WORK IN QUESTION. 9. LOCATION OF CEILING DEVICES, SUCH AS AIR DIFFUSERS, GRILLES, LIGHT FIXTURES, ETC., SHALL BE AS SHOWN ON THE ARCHITECTURAL REFLECTED CEILING PLAN WHERE DISCREPANCIES IN LOCATION OCCUR, THE ARCHITECTURAL PLAN SHALL GOVERN. NOTIFY ARCHITECT OF ANY DISCREPANCIES FOR CLARIFICATION. 10. CONDUIT ABOVE CEILING MUST BE A MINIMUM OF 12" ABOVE THE CEILING GRID. 11. VERIFY ACTUAL CEILING GRID LOCATION AND NOTIFY ARCHITECT OF ANY DISCREPANCIES. 12. MOUNT LIGHT SENSORS WITHIN 12" OF EDGE OF DOOR SWING & MAINTAIN CONSISTENT DIMENSION THROUGHOUT. 13. SPRINKLER INSTALLATION METHOD SHALL REFLECT THE INSTALLATION OF SPRINKLER HEADS TO THE CENTER OF THE TILE PATTERN. 14. CEILING HEIGHT SHALL MATCH EXISTING HEIGHT OF 9'-0", U.N.O. VERIFY IN FIELD. ITEM CUT SHEET/ SPECIFICATION SAMPLE REQUEST DIVISION 8 LT. FIX. -PREFAB. X DOORS &STAIN FINISH X X DOOR FRAMES X X CLG. GRID X CLG. TILE X DIVISION 9 CARPET X(SEAM DIAGRAM) X vcr x RUBBER BASE X PAINT PER SPEC'D FINISH X PLASTIC LAMINATES X METAL LAMINATE X FINISH PLAN GENERAL NOTES 1. NO FINISH SUBSTITUTION MAY BE MADE. 2. WHERE PAINT COLORS CHANGE, CORNERS ARE TO BE CUT --IN FREE OF OVERLAPPING. 3. ALL FIN'SHES ARE TO BE APPLIED IN STRICT ACCORDANCE TO MANUFACTURER'S SPECIFICATION. 4. CLASSES OF MATERIAL BASED UPON THEIR FLAME CHARACTERISTICS SHALL BE SET FORTH IN TABLE 8--8 OF THE C.B.C. 5. THE MAXIMUM FLAME SPREAD CLASSIFICATION OF FINISH MATERIAL USED ON INTERIOR WALLS AND CEILING SHALL NOT EXCEED THAT SET FORTH IN TABLE 8-A OF THE C.B.C. 6. SMOKE DENSITY OF MATERIALS SHALL BE NO GREATER THAN 450 WHEN TESTED IN ACCORDANCE WITH THE UNIFORM BUILDING CODE, STANDARD NO. 42-1 IN THE MANOR INTENDED FOR USE. 7. APPLICATION OF CONTROLLED INTERIOR FINISHES SHALL BE IN CONFORMANCE. WITH SECTION 803 OF THE C.B.C. 8• SUBMIT THE FOLLOWING SAMPLES FOR ARCHITECT'S APPROVAL: A. THREE (3) 12"X12" SAMPLES FOR ALL PAINT, VINYL AND FABRIC FINISHES AND COLORS APPLIED TO A SUBSTRATE WHICH REPRESENTATIVE OF THE SURFACE TO BE FINISHED. SUBMIT PAIN' SAMPLES FROM THE PAINT LOT OR LOTS INTENDED FOR APPLICATION. B. ONE (1) 24"X24" MOCK. UP WITH SAMPLE SEAM (CENTERED) OF ALL FABRIC AND VINYL FINISHES AND COLOR. C. THREE- (3) 12"X12" SAMPLE OF ALL FLOOR COVERING. SUBMIT ACTUAL CUTTINGS OF EACH PRODUCT FOR COLOR/QUALITY CONTROL. 9. ALL PAINT FINISH OF METAL PARTS OF DOORS, HANDRAILS, PERIMETER ENCLOSURES, ETC. SHALL BE SEMIGLOSS, UNLESS OTHERWISE NOTED. 10. ALL PAINT SHALL BE APPLIED IN ACCORDANCE WITH THE MANUFACTURER'S SPECIFICATION FOR THE PARTICULAR SURFACE. 11. ALL SURFACE SHALL BE PROPERLY PREPARED WITH SEALER PRIOR TO THE INSTALLATION OF WALL COVERING PER MANUFACTURER'S RECOMMENDATIONS. 12. ALL V.C.T. TO BE INSTALLED WITH FULL TILE FROM VINYL THRESHOLD STRIP AND FULL TILE FROM WALL ADJACENT TO DOOR SWING, U.N.O. 13. CONTRACTORS TO VERIFY FINISH CONDITION AND LEVEL OF FLOOR TO RECEIVE NEW FINISH TO BE WITHOUT BOWING AT FLOOR OR WALL BASE. CONTRACTOR IS RESPONSIBLE FOR ALL FLOOR PREPARATION. 14. CONTRACTOR TO INCLUDE ALL FLOOR PREPARATION IN BASE BID. 15. WHERE FLOOR MOUNTED OUTLETS ARE REQUIRED ON CARPET AREA, CUT THE CARPET IN AN "X" OVER HOLE AND CARPET. THIS WILL ALLOW CARPET PATCHING WHERE OUTLETS ARE LATER CAPPED. DO NOT TRIM CARPET. 16. PROVIDE AND INSTALL SPECIFIED BASE FOR ALL AREAS TO RECEIVE FLOORING. 17. COORDINATE INSTALLATION OF BASE WITH MILLWORK. DELETE BASE AT WALL WHERE BUILT --IN CABINETS ARE LOCATED. 18. SUBMIT SAMPLES TO ARCHITECT BEFORE PLACING FULL ORDERS WHERE MATERIALS ARE NOT RETURNABLE. NOTIFY THE ARCHITECT IMMEDIATELY OF LONG LEAD TIME ORDER ITEMS. 19. SUBMIT SEAMING PLAN FOR CARPET TO ARCHITECT FOR APPROVAL PRIOR TO CARPET ORDER. 20. PROVIDE P-1 THROUGHOUT UNLESS NOTED OTHERWISE. 21. PROVIDE C--1 THROUGHOUT UNLESS NOTED OTHERWISE. 22. PROVIDE RB-1 THROUGHOUT UNLESS NOTED OTHERWISE. 23. PROVIDE PL-1 THROUGHOUT UNLESS NOTED OTHERWISE. 24. ALL CARPETING SHALL BE INSTALLED WITH GLUE DOWN METHOD, UNLESS NOTED OTHERWISE. 25. CONTRACTOR SHALL PROVIDE PRE -FORMED RUBBER BASE CORNERS. DO NOT CUT OR BEND STRAIGHT BASE TO MAKE CORNERS. 26. FLOOR TILE INSTALLATION SHALL BE THIN SET WITH MINIMAL GROUT LINES. PREPARE AS NECESSARY TO REVIEW TILE INSTALLATION. B v 0 v I, E' 1 6!. 1 PLAN=G & DBBIGN 2916 REM-1 AVE= BiJIIDING 13801, SUTi'B C COSTA I BA. CAT N)NM saeae 714.4311.3111134 L J �' Z .z CD . ,. v 10 THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN AS AN INSTRUMENT OF PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED IN WHOLE OR PART FOR ANY PROJECT OTHER THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION OF BOLE' INTERNATIONAL. THIS DOCUMENT SHALL NOT BE REPRODUCED OR MODIFIED IN ANY WAY WITHOUT THE EXPRESSED WRITTEN CONSENT OF BOLE' INTERNATIONAL. REVISIONS: 9/2/03 - PROJECT START 9/5/03 - CITY SUBMITTAL 9/29/03 -CITY REVISIONS © 10/1/03 -CITY RESUBMIT`TAL U DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED BY: J.A. PROJECT INFO USABLE: +/- 45503 U.S.F. RENTABLE: PROJECT: J08: OBSIDIAN ENT. DATE: SCALE: AS NOTED SHEET NAME SHEET T1.3 Alm I H/C/ SIGN TYP. REF. DET 3/ WHELL STOP 6" CONC. CURB 3" PAINT STRIPE TYP. 'w 'Y. ,Q �t � '•f �_ ♦may / -�� L. 4'.5: y', f i .i :. ~' T•�i • �y4•:T,� k' a�i3i'i' = -cs �' T(�► [y ' � 'i{s,a �;.?h +�rr.'a 'L�+� ��ti . � �`:�'`> s� za'�; • t"' �• V� �-- f�€�VTJi�� fir. y 1+ r•> t Y s 4k s, VAN ACCESSIBLE in 2 _ � n:•'f..`c:;:; rk":'.'" .'.'.�..; ::.'�'a'."""* - •w 5a+�'i - err.., es ° t� s. ,•t.. y'ii.1�S�•j;?� .. -: �. Yb. .�2:} .F.� �!�n 5-�'�?t '�"{. :•2 � `<;; .r.r.,wr. ;v`:} `$�,+ _f :F`=-�'c a ds� .r ".�%n. -'�"y.; > o:ry _�� R..,;, �• � SJ-`' tt .,r •aaaas �� aMr �'f;3'S^ '-!.?�' ��, TY •,,,.a 1?!' =:'� .~.'.'3 '•tea, a��.. - L .it!.t ., �.. •u5w .ri"'.r!..�..rw.e '�'� srwrrr�r�ra•. +swt q+rw.er`aw ....5 >.wa's>a�.rnwar a w�rw:`'r} rra .�. w�rwat.�rr+`r am arr �arr�w�. `'� ta�rr.rrrr++ �'n �wswr wr - �e+t w++�.'u'r°n'r , COstaMesa Freeway __. ... .. . .... _ 0, C/ SITE PLAN foI LANDSCAPING MIN. CONC. WALK N w 0 12"H MIN. WHITE LETTERING 001 3'x3' PAINTED INTL. H/C 0 PXG SYMBOL, PLACED SO L EQ �� THAT IT IS VISIBLE WHEN CAR IS PARKED. NOTE: WHEELCHAIR WITH OCCUPANT PROFILE TO 9�M�� 81_0i3 �,_�„ BE PAINTED IN WHITE WITH BLUE BACKGROUND TYP. NOTE: MAX. SLOPE FOR SURFACE AREAS OF ACCESSIBLE PARKING AREAS, INCL ACCESS • AISLES, SHALL BE 2% MAX. TYP, ADA PARKING STALL DETAIL 10 ACCESSIBLE VERIFY SIZE, COLOR, WORDING, ETC. W/ TRAFFIC ENGINEERING DEPT. PEWT ONLY $10(LOO FINE. n- o �C) cn Z U CID co io � _ METAL SIGN WITH ROUNDED CORNERS 1/4" WIDE BORDER LINE AT ALL SIDES WHITE OCCUPANT ON DARK BLUE BACKGROUND DARK BLUE TEXT ON WHITE BACKGROUND ADDITIONAL SIGN REQUIRED AT VAN ACCESSIBLE SPACES 3"0 STD. STEEL PIPE COL. — PAINTED PAVING OR FINISH GRADE CONCRETE .FOOTING (n a° ' I I , ' l • ,• d '• t �a 8 O 1 •• a i • a�' U • . Q♦ •• A. V-fi" DIA. ACCESSIBLE SIGN DETAIL INTERNATIONAL SYMBOL -- OF ACCESSIBILITY (WHITE SYMBOL ON BLUE BACKGROUND CONFORMING TO COLOR NO. 15090 IN FEDERAL STD. 595B) ADDITIONAL DIRECTIONAL SIGNAGE AS REQUIRED NOTE: MOUNTING LOCATION SHALL BE DIRECTIONAL SO THAT A PERSON MAY APPROACH WITHIN 3� OF THE SIGN WITHOUT PROTRUDING OBJECTS OR INTRUDING IN THE SWING OF A DOOR. ACCESSIBLE SIGNAGE @ DOOR SCALE: N.T.S. IL PIAIRMG is DEMGN 2916 RE MMI AVZNUZ BUI 'l 1, 8E01. SUITE C COSTA XNA - CALI!VMM 926M 714.498.9854 �CA!'I 'R #14L FOR - C CID C,CID JEFFREY W. ADLE � G _ CERTIFIED INTERIOR DESIGNER r, cc 2049 EXPIRES 12-10-03 oul Ili If L� L 4c5 CN WN Z L (. 0 CL LLJ LW Of 0 C/) t C) L0 s r m 1 d y 0 THIS DOCUMENT, AND THE IDEAS AND DESIGNS, INCORPORATED HEREIN AS AN INSTRUMENT OF' PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED . IN WHOLE OR PART FOR ANY PROJECT OTHER THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION OF BOLE' INTERNATIONAL. THIS DOCUMENT SHALL NOT BE REPRODUCED OR MODIFIED IN ANY WAY WITHOUT THE EXPRESSED WRITTEN CONSENT OF BOLE' INTERNATIONAL. N REVISIONS. WM3 - PROJECT START 9/5/03 - CITY SUBMITTAL 9129/03 -CITY REVISIONS I011/03 -CITY RESUBMI TAL A PARTICIPANTS DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED BY: J.A. SITE LEGEND PROJECT INFO � — — EXISTING PATH OF TRAVEL SCOPE OF WORK USABLE: +/- 4,503 U.S.F. RENTABLE: PROJECT: JOB: OBSIDIAN ENT. DATE: SCALE: AS NOTED PLAN SPECIFIC KEY NOTES SHEET NAME Q1 EXISTING ACCESSIBLE PATH OF TRAVEL. O EXISTING ACCESSIBLE PARKING. SITE �3 EXISTING ACCESSIBLE PARKING SIGNAGE PLAN Q 4 EXISTING STRIPING 5'-0° W. AT TYP. ACCESSIBLE PARKING STALL, 8'-0" W. AT TYP. VAN ACCESSIBLE PARKING STALL. SHEET sVe=r-o• aw U scue a/r-r-r v senLc xrs FOR REFERENCE ONLY - EXISTING SHELL - T.I. PERMIT ONLY 1 ST FLOOR EXITING PLAN C2 N EXITING PLAN SCALE: 9 /e"=1'—Ox N i 11 B E' IL PLANMG & Dem" 8915 BE MM AVENUE BUMDING BE01■ 80l'i'a C COSTA WERA. CALLA 98o 714.43aMS4 J3CAkJQI*fA_l~IL FOR I cc c c I D c ci s x ca JEFFREY W. ADLER CERTIFIED INTERIOR DESIGNER M 2049 EXPIRES 12-10-03 UJI Z 0 W LuF UJI <t 0 Q�< W uj or- /z: 0 `: !� u1 III C) -.. Lo cy) u . s THIS DOCUMENT, AND THE IDEAS AND DESIGNS = w- INCORPORATED HEREIN AS AN INSTRUMENT OF PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED IN WHOLE OR PART FOR ANY PROJECT OTHER THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION OF BOLE' t` INTERNATIONAL. THIS DOCUMENT SHALL NOT BE REPRODUCED OR MODIFIED IN ANY WAY WITHOUT THE EXPRESSED WRITTEN CONSENT OF BOLE' INTERNATIONAL. REVISIONS: © 912/03 - PROJECT START a9/5/03 - CITY SUBMITTAL 9/29/03 -CITY REN ISIONS ® 20/1/03 -CITY RESUBMITTAL Q PARTICIPANTS DRAWN BY: C.P. CHECKED 8Y: F.J. DESIGNED BY: J.A. EXITING LEGEND EXITING PLAN SPECIFIC KEY NOTES 1-HR RATED CORRIDOR Ul MAIN PATH OF TRAVEL SHALL BE 44° WIDE MIN. TYPICAL. PROJECT INFO USABLE: +/- 41,503 U.S.F. PRIMARY EXITS RENTABLE: PROJECT: B OCCUPANCY NO CHANGE IN OCCUPANCY USE. JOB: OBSIDIAN ENT. 37 OCCUPANCY LOAD DATE: � PATH OF TRAVEL += SCALE: AS NOTED OCCUPANCY LOAD SHEET NAME ACCESSORY SPACE, ZERO OCCUPANTS EXITING � PLAN SHEET ID Iq I I E3 ALO L! FIANMG '6 =" mia ERMI AVE= Tin Fl=G B201, ou C COSTA YEA, VAIDUEM m2a 714A38.3834 CD .� N C*..j i�'.� Q uj < LU ui < 2: �..oct' < :z LLJ ao 0 << to C.0 Cif 1 THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN AS AN INSTRUMENT Ot"-•' PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED��":, IN WHOLE OR PART FOR ANY PROJECT OTHER THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION OF BOLE' INTERNATIONAL. THIS DOCUMENT SHALL NOT BE REPRODUCED OR MODIFIED IN ANY WAY WITHOUT THE EXPRESSED WRITTEN CONSE OF BOLE' INTERNATIONAL. REVISIONS: 9/2/03 -PROJECT START 9/5/03 - CITY SUBMITTAL 9/29/03 - CITY REVISIONS 10/1/03 -CITY RESUBMTrTAL PARTICIPANTS DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED BY: J.A. PROJECT INFO USABLE: 4503 U.S.F. RENTABLE: PROJECT: JOB: OBSIDIAN ENT. DATE: SCALE: AS NOTED SHEET NAME AS -BUILT/ DEMOLITION PLAN SHEET A2.0 SOAP DISPENSER TOILET PAPER DISPENSER s Qn V_ .,; ;,• r •,• . .,. ENLARGED RESTROOM PLAN 2 NEW A.D.A. COMPLIANT RESTROOM SANITARY NAPKIN WASTE cl SEAT COVER DISPENSER 93 PAPER TOWEL DISPENSER & DISPOSAL Ll ❑g WATER HANDICAP CLOSET URINAL TYP, ACCESSIBLE RESTROOM HEIGHTS 3/8='-o (FOR REFERENCE ONLY) LAVATORY MI SINK MIRROR :•, 2 �■� �t � � ® wit' �� l 1 GENERAL CONSTRUCTION NOTES: 1. REPAIR ALL EXISTING TO REMAIN PARTITIONS, DOORS, FRAMES, ETC. THAT ARE TO RECEIVE A NEW FINISH. ALL FINISHES TO MATCH EXISTING, U.N.O. 2. BRACE/REINFORCE ALL NEW OR EXISTING PARTITIONS TO RECEIVE MILLWORK AS REQUIRED. 3. REFER TO SHEET T1.2 FOR ALL A.D.A./TITLE 24 RELATED MOUNTING AND LOCATING REGULATIONS. 4. IF OUTLETS ARE INSTALLED DIRECTLY INTO CORE WALLS, SEAL/INSULATE AS REQUIRED PER CODES TO MAINTAIN THE INTEGRITY OF WALL RATING. REFER TO ELECTRICAL & TELEPHONE PLAN FOR LOCATION. 5. VERIFY ALIGNMENTS IN FIELD. IF MISALIGNMENT OF EXISTING ELEMENTS SHOULD OCCUR, VERIFY OPTION OF FURRING COLUMN TO PROVIDE REQUIRED ALIGNMENT. 6. LEVEL OR "FLOAT" FLOORS WHERE REQUIRED FOR LEVEL FINISH AND APPEARANCE. 7. REFER TO SHEET A6.0 FOR DOOR SCHEDULE, AND HARDWARE TYPES. 8. ANY DAMAGE DONE BY ANY EXISTING FIRE. PROOFING SHOULD BE REPAIRED WITH COMPARABLE MATERIAL HAVING THE SAME FIRE RESISTIVE RATING. 9. REFER TO SHEET T1.1 FOR ADDITIONAL NOTES. IC- % Typ. PARTITION PLAN SCALE: 1 /80` 1 .--o; N WALL LEGEND PARTITION PLAN SPECIFIC NOTES: EXISTING INTERIOR PARTITION TO REMAIN i PROVIDE 4'W BLDG. STD. TEMPERED GLAZING AND FRAMES AT THESE OFFICES. ALIGN WITH TOP OF DOOR FRAMES. WINDOW TO BE 3'-0" A.F.F. NEW INTERIOR NON -RATED 3-5/8° THICK STUDS W/ INSULATION. FLOOR SLAB TO UNDERSIDE OF FINISHED CEILING W/SEISMIC BRACING, U.N.O. 5/8" GYP. WALL BOARD W/ JOINTS TAPED, EXISTING COUNTERTOP IS AT 34" A.F.F. WALL BOARD EDGE SHALL OCCUR OVER FRAMING MEMBERS, ONE LAYER EA. SIDE OF STUDS. SEE DETAILS 2/A7.0 & 4/A7.0. 3 NEW A.D.A. COMPLIANT RESTROOM STALL. INSTALL A.D.A. COMPLIANT GRAB BARS NOTE; SEE METAL WALL STUD TABLE TO SELECT APPROPRIATE WALL. STUD SIZE FOR WALL HEIGHT ALIGN ALIGN FACE OF NEW CONSTRUCTION TO EXISTING NOTE: PATCH AND REPAIR EXISTING PARTITIONS AS NEEDED. NOTE: REF. FINISH PLAN, SHEET A6.0. C� DOOR NUMBER -REFER TO DOOR SCHEDULE, SHEET A5.0 EXISTING DOOR TO REMAIN WINDOW TYPE - REFER TO WINDOW TYPE SHEET A5.0 110 it BE' PLSNMG ie DMGN 8915 RIDE111 AVENUX B IUMG BE01, 80rr8 C COSTA XNA. CALUUM41A seese 714,38.3884 I a 3$ f 3 3 F R JEFF W.ADLER } 3 p CERTIFIED INTERIM DESIGNER !(.♦ 1 • ) 1 i F Y W — ui Q Z �.o 3:cn C) Lo U) •s 4 t THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN AS AN INSTRUMENT Of__,",r , PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED';: IN WHOLE OR PART FOR ANY PROJECT OTHER THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION OF BOLE INTERNATIONAL. THIS DOCUMENT SHALL NOT_s;w v BE REPRODUCED OR MODIFIED IN ANY WAY WITHOUT THE EXPRESSED WRITTEN CONSENT 3 OF BOLE' INTERNATIONAL. REVISIONS: 9/2103 - PROJECT START L.� 9/5/03 - CITY SUBMITTAL a9/29/03 - CITY REVISIONS 1011f03 -CITY RESUBi• WEAL L...J PARTICIPANTS DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED BY: J.A. PROJECT INFO USABLE: +/- 4,503 U.S.F. RENTABLE: PROJECT: JOB: OBSIDIAN ENT. DATE: SCALE: AS NOTED SHEET NAME PARTITION PLAN SHEET A2.1 Boo It BE' IL I FIANMG & UMN 2915 Fxm Avmm mmmG B2011 suffm c CONA MEA, CAI MMU SMOG 714ASO.SM g-offim-C"r1u, IrIXTA t JEFFREY W. ADLER s.* CERTIFIED DESIGNER 2049 EXPIRES 12-10-03 -'\ Ii� C:) C.0 tk Lo THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN AS AtT INSTRUMENT OF", PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED IN WHOLE OR PART FOR ANY PROJECT OTHER! `, c; THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION OF BOLE' INTERNATIONAL. THIS DOCUMENT SHALL NOT BE REPRODUCED OR MODIFIED IN ANY WAY WITHOUT THE EXPRESSED WRITTEN CONSENT OF BOLE' INTERNATIONAL. REVISIONS: 9/2103 - PROJECT START 9/5/03 - CITY SUBMITTAL 9/29/03-CITY REVISIONS 10/1/03 - CITY RESUBMF17AL n m PARTICIPANTS DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED BY: J.A. PROJECT INFO USABLE: 45503 U.S.F. RENTABLE: PROJECT: JOB: OBSIDIAN ENT. DATE: SCALE: AS NOTED SHEET NAME POWER & TELE/DATA PLAN SHEET REFLECTED CEILING GENERAL NOTES: REFER TO SHEETS T1.1 AND T1.3 FOR ADDITIONAL NOTES. 7w. np. fiu REFLECTED CEILING PLAN REFLECTED CEILING LEGEND EXISTING BLDG. STD. 2 x4' GRID AND TILE. EXISTING BLDG. STD. 2 s x4' FLUORESCENT LIGHT FIXTURE (3 LAMP) WITH 18 CEI I PRII;MA'n(' I FNql PPW P1 17rTPIrAl Ifi III DRAWINGS. EXISTING U.N.O. BLDG. STD. EXIT SIGN -120/277 VOLT .SLC (UL) RATED - LUMINANCE - .06 FT., GRID MOUNTED, MEET ALL CBC REQUIREMENTS. RE -USE WHERE POSSIBLE. ALL EXIT SIGNS EXIT ILLUMINATION TO BE ON BATTERY BACK UP POWER & SEPARATE CIRCUIT [CBC-1003.2.8.5]. EXISTING U.N.O. DENOTES EXISTING SUPPLY VENT SQXE: 1 /8 n =11-o REFLECTED CEILING PLAN NOTES O REPAIR OR REPLACE ANY DAMAGED OR MISSING CEILING TILES EXISTING CEILING TO REMAIN U.N.O. O INSTALL NEW OR RELOCATED FIRE EXIT SIGN. NOTE: ALLDEVICESARE EXISTING, U.N.O. NOTE: MECHANICAL SYSTEM TO REMAIN -AS -IS, NO CHANGE SHALL BE DONE TO MECHANICAL LAYOUT, NOTE: CEILING THROUGH -OUT SUITE SHALL BE 91-0- A.F.F., U.N.O. DENOTES EXISTING RETURN DIFFUSER NOTE: LIGHT AND -VENTILATION PER CBC SEC. 1202. MIN. OF 15 CFM OF OUTSIDE AIR PER OCCUPANT IS REQUIRED, DENOTES HEIGHT OF CEILING NOTE:` LIGHT AND VENTILATION REQUIREMENTS ON THE PLANS ARE IN ACCORDANCE WITH THE CBC REQUIREMENTS FOR EACH TYPE OF USE. FOR RESTRICTIONS ON THE USE OF CORRIDORS TO CONVEY DENOTES RELOCATED DEVICE/MATERIAL CODE. AIR, SEE CHAPTER 6 OF THE MECHANICAL DENOTES NEW MATERIAL OR CONDITION NOTE- ALL ENCLOSED PORTIONS OF THE BUILDINGS CUSTOMARILY OCCUPIED BY HUMAN -BEINGS SHALL BE PROVIDED WITH A MECHANICALLY OPERATED VENTILATION SYSTEM. SUCH MECHANICALLY OPERATED VENTILATION SYSTEM SHALL BE CAPABLE OF SUPPLYING A MINIMUM OF 15 CUBIC FEET PER MINUTE 'OF OUTSIDE AIR PER OCCUPANT DURING SUCH TIME AS THE BUILDING IS OCCUPIED. IF THE VELOCITY OF AIRAT_A REGISTER EXCEEDS 10 FEET PER SECOND, THE REGISTER SHALL 8 LACED MORE THAN 8 FEET ABOVE THE FLOOR DIRECTLY BENEATH. CBC SECTIO 1202. B A 0 a t I E , IL I PI&VMG 2915 RIM-T Avlm BURMG B201, SU c COBTA XNA- CAT IMM m2a 714A38.3M CCIDC ClAk m JEFFREY W. ADLER 7CERTIFIED INTERIOR DESIG14ER = cltl 2049 EXPIR C:) CV C) ui _D cl) < uj < 0 � < uj < Q: w 77 (p Lo THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN AS AN INSTRUMENT OF PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED IN WHOLE OR PART FOR ANY PROJECT R THAN THE ONE IDENTIFIED HEREIN Wrlr7HO THE WRITTEN AUTHORIZATION OF BOLE' INTERNATIONAL. THIS DOCUMENT SHALL N T 'y BE REPRODUCED OR MODIFIED IN ANY WAY WITHOUT THE EXPRESSED WRITTEN CONS OF BOLE' INTERNATIONAL. REVISIONS: 9/2/03 - PROJECT START 9/5/03 - CITY SUBMITTAL 9/29/03 - CITY REVISIONS 1011103 - CITY RESUBMITTAL PARTICIPANTS DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED BY: J.A. PROJECT INFO USABLE: 4,503 U.S.F. RENTABLE: PROJECT: JOB: OBSIDIAN ENT. DATE: SCALE: AS NOTED SHEET NAME REFLECTED CEILING PLAN SHEET A4.0 DOOR SCHEDULE DOOR SCHEDULE DOOR DOOR SIZE MATERIAL FINISH N0. TYPE I WIDTH HEIGHT DOOR I FRAME I DOOR FRAME HARDWARE & FIRE REMARKS GROUP TYPE RATING DOOR HARDWARES SINGLE OR PAIR OF GLASS DOORS Al. SINGLE STOREFRONT GLASS DOOR PAIR WOOD OR HOLLOW METAL DOOR 1. SCHLAGE 'D' LEVER SERIES LATCHING HARDWARE FOR USE ON INTERIOR OPERATING HARDWARE MS 1850S C 1. STANDARD DOOR DOORS, BRUSHED ALUMINUM FINISH. CYLINDRICAL WITH MATCHING CYLINDER GUARD MS 4043 BUTTS SO T88 STRIKE 40' A.F.F. TO CENTERLINE OF LEVER. EXIT INDICATOR 4089 STOP W1276 C.C.S a. D80PD - F86 -STOREROOM LOCK THRESHOLD 200D BOLTS FOB OR FB7 b. D91PO - F82 - ENTRANCE LOCK - c. D50PD - F82 -OFFICE LOCK A2. PAIR OF STOREFRONT GLASS DOOR C2. STANDARD DOOR WITH CLOSER: d. 010S - F75 - PASSAGE LATCH (3 POINT LOCK) BUTTS 450 T88 e. D70PD - F84 -CLASSROOM LOCK OPERATING HARDWARE MS i850S STOP W1276 C.C.S 2. NOT USED THRESHOLD BOLT HEADER BOLT 40fi5 4085 BOLTS FB8 OR FB7A 3. VON DUPRIN 99 SERIES PANIC DEVICE OR APPROVED EQUAL CYLINDER GUARD MS 4043 CLOSER 8581 BF a. 9975L X 575 - SINGLE DOOR EXIT INDICATOR 4089 C3. ARE RATED DOOR: b. 9947L X - PAIRS OF DOORS (CONCEALED VERTICAL RODS) THRESHOLD 2000 BUTTS 450 TB8 DELETE: 355CS, COR2, F98/7 SINGLE WOOD OR HOLLOW METAL DOOR STOP W1276 C.C.S PROVIDE 297DS, 293DP AT ARE DOORS B1. STANDARD DOOR: CLOSER 8581 BF c. 9927L - PAIRS OF DOORS (CONCEALED VERTICAL RODS) BUTTS T88 SAS S88 DELETE: 355CS, COR2, FBS j7 STOP W1 W1276 C.C.S BOLTS BOLTS FB8 OR FB7 PROVIDE: 2970S, 293DP AT ARE DOORS 357D d. USE SCHLAGE 20-001 (1 1/41 CYLINDER. 82. STANDARD DOOR WITH CLOSER: COORDINATOR COR2 e. USE FIRE RATED HARDWARE WHERE REQUIRED. BUSS 450 T88 4. TRIMCO 100 SERIES PUSH/PULL PLATES OR APPROVED EQUAL. STOP W1276 C.C.S C4 EXTERIOR DOOR: a. 1001-3 PUSH PLATE CLOSER 8581 BF BUTTS 450 T88 b. 1014-3 PULL PLATE 03. ARE RATED DOOR: STOP CLOSER W1276 C.C.S 8581 BF ALL DOORS SHALL BE CONSISTENT WITH BLDG. STANDARD SPEC. NO DEVIATION. BUTTS 450 T88 SEALS S88 THE DOOR AND FRAME SHALL BEAR AN APPROVED LABEL OR OTHER IDENTIFICATION, SHOWING STOP W1276 C.C.S BOLTS - HEADER & THRESHOLD F08 OR F07 THE RATING THEREOF, FOLLOWED BY THE THE LETTER 'S', THE NAME OF THE MANUFACTURER, CLOSER 8581 OF 1/2' EMBED. AND THE IDENTIFICATION OF THE SERVICE CONDUCTING THE INSPECTION OF MATERIALS AND SEALS S88 FULL LENGTH STEEL ASTRAGAL 3570 WORKMANSHIP AT THE FACTORY DURING CONSTRUCTION AND ASSEMBLY. DOORS SHALL BE DOOR SHOE 216DV MAINTAINED SELF -CLOSING OR SHALL. BE AUTOMATIC CLOSING BY ACTUATION OF A SMOKE B4. EXTERIOR DOOR: THRESHOLD 200D DETECTOR IN ACCORDANCE WITH SECTION 713.2. SMOKE AND DRAFT CONTROL DOOR BUTTS 450 T88 ASSEMBLIES SHALL. BE PROVIDED WITH A GASKET SO INSTALLED AS TO PROVIDE A SEAL. WHERE STOP CLOSER W1276 C.C.S 8581 BF C5. BY-PASSING DOORS: TRACK ASSEMBLY BY DOOR SUPPLIER THE DOOR MEETS THE STOP ON BOTH SIDES AND ACROSS THE TOP. CBC SECTION 1004.3.4.3.2. SEALS S88 CONTRACTOR TO PROVIDE CALLOUT KEYWAY WITH DOOR/HARDWARE FROM SUBMITTAL LATCH GUARD L00 THRESHOLD 2 NOTE: FOR DOORS THAT ARE RELOCATED AND HAVE LOCKS THAT ARE NOT NEEDED DOOR SHOE 21606DV REMOVE LOCKS AND COVER WITH MATCHING FACEPLATES, STORE REMOVED DOOR HARDWARE FOR POSSIBLE REUSE LATER CLOSING DEVICES 1. LCN 41 1 0 SERIES CLOSER FOR CORRIDOR DOORS, ALUMINUM FINISH. a. 4030 BF - TYPICAL.. DOORS b. MAX. EFFORT TO OPERATE DOORS 1. OGBIOR DOORS - 8.5 LDS. 2. INTERIOR DOORS - 5.0 L OS. 3. ARE RATED DOORS - 15 L OS. c. A CLOSING DEVICE MUST BE USED ON ALL ARE RATED DOORS. BUTT HINGES: 1. HAGER - 700 BUTT HINGES, 2 PAIR, FINISH TO MATCH DOOR OR APPROVED EQUAL EQUAL USE HAGER BB-700 AT DOORS W/CLOSERS. 2. oIZE . 4 1/2; X 4 1/2' FOR 1 3/4' DOORS b. 3 1/2 X 3 1/2 FOR 1 VfIx DOORS C. MANUFACTURER'S GUIDELINES FOR ALL OTHER DOOR THICKNESSES. 3. 1 fi 2 PAIRS FQR DOORS 90' AND AN ADDITION PAIR FOR EVERY 3O' OR FRACTION THEREOF. 4. D00 S OVER 42 WIDE - FOLLOW MANUFACTURERS GUIDE. 5. ALL EXTERIOR OUT SWING DOOR BUTTS SHALL BE MADE OF NONFERROUS MATERIAL. AND SHALL. HAVE STAINLESS STEEL HINGE PINS. 6. ALL MOR OUT SWING DOORS SHALL HAVE NON-REMOVEABLE PINS. 7. ALL ARE RATED DOORS OR DOORS WITH CLOSING DEVICES SHALL HAVE BALL. BEARING HINGES. BOLTS: 1. MANUAL FLUSH BOLTS a. TRIMCO 3917 OR APPROVED EQUAL b. LENGTH TO SET AS FOLLOWS: 1. BOTTOM BOLTS 12' 2. TOP BOLTS 12 FOR DOORS TO 80' 3. TOP BOLTS 24' FOR DOORS TO 85' TO 96' 4. TOP BOLTS 36' FOR DOORS OVER 96' 2. AUTOMATIC FLUSH BOLTS. a. G.J. F87 OR APPROVED EQUAL FOR HOLLOW METAL DOORS. b. G.J. FB8 OR APPROVED EQUAL FOR WOOD DOORS. 3. AUTOMATIC FLUSH BOLTS MUST BE USED ON ALL PAIRS OF ARE DOORS. STOPS: 1. BRASS BUILDERS WORKS F8061 (US32D SATIN CHROME), OR APPROVED EQUAL TYPICAL KICK PLATES: 1. TRIMCO 1024 OR APPROVED EQUAL 2. SIZE AS FOLLOWS: a. 10 X 2' LESS THAN :DOOR WIDTH - SINGLE DOOR b. 10' X 1' LESS THAN DOOR WIDTH - PAIR OF DOORS WEATHER STRIPPING: 1. PEMKO 200D THRESHOLD - OUT SWING EXTERIOR DOORS. 2. PEMKO 216DV DOOR SHOE - OUT SWING EXTERIOR DOORS, 3. PEMKO S88 HEAD &JAMB SEAL - ALL EXTERIOR AND ARE RELATED DOORS. 4. PEMKO 355DS ASTRAGAL FOR INTERIOR DOORS (SEE LATCH GUARDS FOR EXTERIOR DOORS). LATCH GUARD: 1. G.J. LP-2 SINGLE EXTERIOR DOOR 2. PEMKO 357 �ASTRAGAL�- PAIRS OF DTTERIOR DOORS KEYING: AS D RECTED OWNER AND ARCHITECT. SIDELIGHT: 1. 2'-0' X 8'-10' 'MODULEX' PRE -FINISHES METAL SECTION. COLOR: BLACK DOOR NO. DOOR SIZE MATERIAL FINISH HARDWARE & GROUP TYPE a FIRE RATING TYPE WIDTH HEIGHT DOOR FRAME DOOR FRAME ::2o 0 B 6'--0" 8'-10" WOOD METAL MT. EXTG. MT. EXTG. 1 d :K4D A 3'--0" 8'-10" WOOD METAL MT. EXTG. MT. EXTG. ::2:OD A 3' -0" 8' -10" WOOD METAL MT: EXTG. MT. EXTG. 1 d :21D A 3' - 0" 8' -10" WOOD METAL MT. EXTG. MT. EXTG. - 210 A 3'--0" 8'-10" WOOD METAL MT. EXTG. MT. EXTG. Z D7 A 3' -- 0" 8' -10" WOOD METAL MT. EXTG. MT. EXTG. 1 d 218 A 3'--0" 8'-10" WOOD METAL MT. EXTG.. MT. EXTG. 1 c DOOR NOTES DOOR TYPES 1.) REFER TO THE PLANS AND SPECIFICATIONS FOR ADDITIONAL DOOR INFORMATION. 2.) VERIFY THAT ALL DOORS AND DOOR HARDWARE MEET THE REQUIREMENTS OF THE CALIFORNIA r5 5 ADMINISTRATIVE CODE (TTTLE 24) AND ALL OTHER GOVERNING CODES & STANDARDS. 7.0 TYP. 7.0 TYP. NOTIFY THE ARCHITECT IMMEDIATELY IN CASE OF DISCREPANCY. 3.) EXIT DOORS: A. ALL EXIT DOORS SHALL BE OPENABLE FROM INSIDE WITHOUT THE USE OF A KEY OR ANY SPECIAL. KNOWLEDGE. B. ALL DOOR SWINGS SERVING AN OCCUPANT LOAD OF 50 OR GREATER SHALL SWING IN THE DIRECTION OF EXIT. 4.) MOUNT ALL HARDWARE PER LATEST EDITION OF GOVERNING CODES. a 5.) ALL GLAZING IN DOORS OR WITHIN TWENTY-FOUR (241 INCHES OF DOORS AND WITHIN SIXTY (601 INCHES OF WALKING SURFACE SHALT. BE TEMPERED. ALL GLAZING GREATER THAN 9 S.F. WITHIN 18, VERTICALLY OR 36' HORIZONTALLY OF WALKING SURFACE WHOSE TOP EDGE IS HIGHER THAN 36' ABOVE THE FLOOR. C i I lT/+umn lain i tlntimm nnnnh , txr fine- . e■a,n ■,r,,,..., .. 3'--0' TYP. 3'-0n TYP. u.) Ln"I"wlu nvw w%,nuru uuuRz) InHI tint rmu RW1YRIt:U )HALL tit UVtNPJJLt WIIH A SINGLE EFFORT WITHOUT REQUIRING THE ABILITY TO GRASP THE HARDWARE (LEVER OR PUSH TYPE) MOUNTED 30' TO 44' ABOVE THE FLOOR. CBC CHPT. 10, SECTION 1023.3.1.8. 7.) MAXIMUM EFFORT TO OPERATE DOORS SHALL NOT EXCEED THE FOLLOWING PER THE REQUIREMENTS OF CALIFORNIA BUILDING CODE, TITLE 24, CHPT. 10 SECTION 1003.3.1.6. DOOR NOTES: 1. PER CBC 1998 APPENDIX CHAPTER 34 #3407.3. EXISTING DOORS LOCATED A. INTERIOR DOORS - 5 POUNDS WITHIN EX. 1-HR. RATED CORRIDOR SHALL BE EXEMPT FROM MEETING B. EXTERIOR DOORS - 8.5 POUNDS CURRENT CODE REQUIREMENTS. C. ARE DOORS - 15 POUNDS 2. NEW RATED DOORS SHALL COMPLY WITH CBC CHAPTER 10. 8.) ALL INT. DOOR FRAMES TO BE BLDG. STD. FINISHED. SPECIFIED BY BOLE'. 3. ALL GLAZING WITHIN A 24° ARC OF EITHER EDGE OF A DOOR AND WITHIN 9.) THE FLOOR AND LANDING SHALL NOT BE MORE THAN 1/2' LOWER THAN THE THRESHOLD 60 OF THE FLOOR SHALL BE TEMPERED. OF THE DOORWAY. BEVEL (1:2 MAX. SLOPE) WHERE THE THRESHOLD EXCEEDS 1/4' 4. ALL EXITS TO BE OPENABLE FROM INSIDE WITHOUT USE OF A KEY OR ANY IN HEIGHT. CBC SECTION 3304(I1)1 SPECIAL KNOWLEDGE OF EFFORT. CBC CHPT. 10, SECTION 1003.3.1.8. EX. PANIC HARDWARE TO REMAIN, 10.) THE BOTTOM 10' OF ALL DOORS EXCEPT AUTOMATIC AND SLIDING DOORS SHALL HAVE A SMOOTH UNINTERRUPTED SURFACE. CBC SECTION 3304(I.3). 5, ALL DOOR HARDWARE SHALL 8E LEVER TYPE, PUSH TYPE, OR PANIC BAR HARDWARE. CBC CHPT. 10, SECTION 1003.3.1.9. 11.) PROTECT ALL INTERIOR OPENINGS IN RATED CORRIDOR WAS AND CEILINGS. DOOR AND 6. �T = TEMPERED FRAME MUST BE PROTECTED BY A TIGHT -FITTING SMOKE -AND -DRAFT -CONTROL ASSEMBLY HAVING A FIRE -PROTECTION RATING NOT LESS THAN 20-MIN. WHEN TESTED IN ACCORDANCE 7. HARDWARE TO COMPLY WITH EXITING AND DISABLED ACCESSIBILITY WITH CBC STANDARD N0. 1-2, PART II, WITH SELF CLOSURES OR AUTOMATIC CLOSURES REQUIREMENTS (CBC SECTIONS 1003.3.1.8, 1133B.2.5, AND 1133B.2.5.1) WITH SMOKE DETECTORS. CBC 1004.3.4.3.2.1 REMARKS NEW BLDG. STD. RELOCATED NEW BLDG. STD. RELOCATED RELOCATED NEW BLDG. STD. NEW BLDG. STD. WINDOW TYPES 3'-On 1'-90 4'-nsl 1.. TYP. TYP. (MATCH EXISTING FOR DIMENSIONS) WINDOW NOTES: 1. FIELD MEASURE ALL OPENINGS PRIOR TO FABRICATION. 2. TOP OF WINDOW & SIDELIGHT TO MATCH DOOR FRAME HEIGHT. pr L PLG & D=GN JJUM G B201, BUTTlS C COSTA MMA, CAI N)RNta 98888 714AS11.3834 P t cclDc i INTERIORCERTIFIED 1 2049 EXPIRES -03 1 1 THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN AS AN INSTRUMENT OF PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED IN WHOLE OR PART FOR ANY PROJECT OTHER THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION OF BOLE INTERNATIONAL. THIS DOCUMENT SHALL NOT BE REPRODUCED OR MODIFIED IN ANY WAY WITHOUT THE EXPRESSED WRITTEN CONSENT OF BOLE' INTERNATIONAL. REVISIONS: W2103 -PROJECT START A9/5/03 -CITY SUBMITTAL L 3 9/29/03 - CITYREVISIONS ® 10/1/03 -CITY RESUBMrI7AL PARTICIPANTS DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED 8Y: J.A. PROJECT INFO USABLE: +/- 41503 U.S.F. RENTABLE: PROJECT: JOB: OBSIDIAN ENT. DATE: SCALE: AS NOTED SHEET NAME DOOR & WINDOW SCHEDULE SHEET SCALE: NTS B go It I E, L PIAlf=G & D=GN 2915 ginmur. ATKNUZ BuTfmn,G B201, Isu C COSTA XNA- CALF! PMA m2a 714A36.3834 Rmyr - ovaiim i'�: CN CN 0 Lu U) < < _0 LUF-- - 0 < ry< z < F- cn W� �� Q� �C U w Lo THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN AS ANT INSTRUMENT OF PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED IN WHOLE OR PART FOR ANY PROJECT OTHER THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION OF BOLE! INTERNATIONAL. THIS DOCUMENT SHALL NOT BE REPRODUCED OR MODIFIED IN ANY WAY WITHOUT THE EXPRESSED WRITTEN CONSENT OF BOLE' INTERNATIONAL.' REVISIONS: 912/03 - PROJECT START Z-\ 9/5/03 - CITY SUBMITTAL I a all 9/29103 -CITY RENISIONS I0/1/03 - CITY RESUBMITTAL he AW'4 PARTICIPANTS � �,,; DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED BY: J.A. PROJECT INFO USABLE: 4,503 U.S.F. RENTABLE: PROJECT: JOB: OBSIDIAN ENT. DATE: SCALE: AS NOTED SHEET NAME FINISH PLAN SHEET A6.0 vul --- METAL STUD n ..........VINYL TRANSITION STRIP (SEE PARTITION PLAN) NOISE BARRIER BAIT INSULATION WHERE OCCURS BATT INSULATION (WHERE SHOWN CARPET ON PLANS). 5/8" TYPE "X" GYP. BID. 0/ MTL. STUD ONE LAYER 5/8" TYPE 'X$ F 'oo BACKING PLATE, SEE GYP. BD. ON EACH SIDE 7/Al 10 METAL STUDS 18/25 GA. MLT. STUD @ 24" O.C. REF. SHEETS 1-1/4" TO 1-1/2" ICBO # 2274 A-2, A-3 FOR SPECS. & LOCATIONS. NOMINAL DIAMETER VCT/ CARPET TRANSITION PRE -FINISHED ALUM. BREAK (2) CONT, STRIPS DBL. FACE VINYL TAPE -TYPICAL ............ METAL TO MATCH EXISTING CERAMIC T11 F. I I STOREFRONT PAINT TO REFER TO FINISH PLAN FORS FLOOR & THINSET MATCH WALLS BASE SPECIFICATIONS N) .J SCHLUTER, 1/8"W x 1/2"D "L" TOP OF FLOOR SLAB 44A\ 1/2t 7 WALL .............. SHAPED DIVIDER, NICKEL FINISH, CARPET. NEOPRENE to GASKET CONT. STUD CHANNEL FASTEN TO LATEX SLOPE 1/8':12' CONC. FLR. W/POWER DRIVEN FASTENERS 14 — ------ TYP. @ 48" O.C. MAX. & 6" MAX. ENDS 00 USE "HILTI" OR EQ. SHOT PIN. APPROVED ICBO FOR ALL SIZES NO. 2388, OR REDHEAD CERAMIC TILE/ CARPET TRANSITION EXISTING GLASS & FRAME SHOT PIN (I.C.B.O. #1147) NOTE: DO SCREW INTO BASE MIMING MLIWONS SLAB SECTION THR"'OUGH TYP. GRAB BAR TILE/ VCT TO CARPET TRANSITION PARTITION TERMINATING Lv@) MULLION C��CTION SCALE: 3=1'-O' v SCALE: NTS SCALE: NTS 8 2 NONUNION SCALE: 1 1/2"=l'-O* 4 LATERAL FORCE BRACING NOTE ---- -- INSTALL BOLT TO SECURE 1. STRUTS OTHER THAN EMT MAY REQUIRE ENGINEERING CALCULATIONS. ONE TUBE TO THE OTHER. 2. STRUTS OVER 12 FEET MAY REQUIRE ENGINEERING CALCULATIONS. LONG AND HEAVY TUBES SHALL LAP ONE STRUTS PRESENT ADDITIONAL SEISMIC HAZARD; THEREFORE, THE APPLICANT MAY BE ANOTHER AT LEAST 4" IN REQUIRED TO PROVIDE CALCULATIONS SHOWING THAT ADDITIONAL STRUT LOAD CAN FULLY EXTENDED POSITION. BE SUPPORTED VERTICALLY AND LATERALLY BY THE SUSPENSION SYSTEM ELEMENTS TAPE W/ JOINT COMPOUND 5/8 NO. 12 GA. VERTICAL WIRE HANGER,SUCH AS MAIN RUNNERS, VERTICAL AND SPLAYED WIRED, ETC. GYP. BD., BOTH SIDES & SAND SMOOTH TYPICAL. TURN CEILING GRID LEVEL PRIOR TO SETTING TUBE. METAL STUDS ONE 0.14" OC. SHOT PIN MTL. FINISH FRAME AT EACH STUD BRACE UNDERSIDE OF FLOOR OR MATCH EX. 14 ROOF STRUCTURE ABOVE. 5/8" TYP. "X" GYPSUM ICBO NO. 2388 PLACE SHOT PIN OC. SEE MAX. HEIGHT SCHEDULE BOARD AT BOTH SIDES. OF FLUTES C:) a - DRILL 5/32" HOLE CN LVIP f %I SLE E BOLT AND LOCKING NUT. I lot., AND INSTALL 1/8 EMT COPE FLANGE OF 1 $-on 2 STUD AS REQUIRED I OC SUSPENDED CEILING SYSTEM 1/4" FIXED SAFETY GLAZING, WIRE GLASS WHERE REQ'D. CROSS RUNNER SEE CEILING PLAN. SYSTEM TO BE FOR METAL STUDS, SEE METAL DIAGONAL BRACING COMPLIANT W/C.B.C. 1998, SEC. 2502 SLOT END OF TUBE STUD TABLE ON THIS SHEET AT 4'-o" OC. NO TO FIT OVER CEILING . 4, UBC 25-2. DOOR PER SCHEDULE RUNNER ELECTRICAL METALLIC TUBING (EMT) ONLY 454 TYP. METAL CORNER BEAD W/ '7 '-7 SIZE (DIAMETER) L (MAX. HEIG• $-ON JOINT COMPOUND & SAND SMOOTH MAIN RUNNER 1/2 4 NOTE GLASS AND GLAZING SHALL BE IN ACCORDANCE WITH C.B.C. v I 3/4" V-22 CHAPTER 24. NOTE ON THE DRAWINGS ALL, WINDOWS AND DOORS HAVING TYPICAL. NOTE: BRACING SHALL BE COMPLIANCE WITH C.B.C. SECT. 1611.5 in 6S-60 GLAZING. 1 1/4- 8'-6* FOR LATERAL BRACING OF WALLS. 1 1/2' 9'-100 2" 12'-On SUSPENDED CEILING- GRI D WINDOW DETAIL BRACING PERPENDICULAR ._..� SCALE: NTS 15 SCALE: 1-1/2u=1'-0u WALL CORNER TYP. TG STRUCTURE ABOVE SCALE: NM JSCALE: NITS -CLBR-Ol.d wg) 3 SEE SEISMIC BRACING DETAIL FOR BRACING M STRUCT. ABOVE r3 EXISTING WALL. MIN. OF (2) 12 GA HANGAR WIRES TO N, ATTACH BRACING TO TOP TRACK INSULATION WHERE OCCURS W/ 2 #8 SCREWS STRUCTURE ABOVE SEE PLAN . (MAY BE SLACK) ( ) Yee 0000 4 AC CEILING TILE SUSPENDED REFER TO REFLECTED 00 CEILING GRID PLAN FOR SPEC. or TO BE UNDER ALIGN W/TOP OF DOOR COMPLIANCE W/C.B.C. 1998 SEC, 25020 CASING BEAD TYP. NO. 4, UBC 25-2. CONT." MTL, MTL. DOOR/WDW FRAME W/MTL. STOP, HEADZJAMB RSC PEMKO NEOPRENE GASKET a - PAINT ENAMEL SEAL AT REGULAR CEILING TERMINATION cn STUD SHALL NOT ATTACH TO CLG. GRID _-----I...........PARTITION, SEE PARTITION (T) CUT CEILING GRID AS REQ'D. U-1 1/4" TEMP CLEAR GLASS m PLAN. 5 TYPE "X" GYP. BD. u.J o /8 LIGHT FIXTURE ICBO NO 1632, 0/ EACH SIDE u_ uj (LESS THAN 56 LBS.) OF MTL. STUDS. REFER TO FLOOR PLAN FOR MTL. STUD SPECS. uj NOTE: GLAZING TO BE SUPPORTED ON ALL 4 SIDES. VERTICAL CEILING STRUT WINDOW HEAD TO CEILING PARTITION TO SCALE: NITS (I-CLCS-Ol.dw 14 SCAI •F: NTS —NEW WALL TO EXISTING UNDERSIDE OF SUSP. CLG: SCALE: NTS 6 SCALE: NITS (I-PAUS-Ol.dwg) 2 STOP SPACING (O.C.)STOP DESIGNATIO MIN.#12 GAUGE�i2"� DENOTES DEPTH TYP) DENOTES SECTION / GUAGE (TYP) 1/4" TEMP. GLASS 3 7/8- 1 WALL HEIGHT--,,,, Up To 109-0 - - - ----------------- 5/8" TYPE 'X' GYP. BD. 250CC25 kiln r%f%f%rl /IIM'%Ilf rl-NAAJr nI ITC!InC* c mr nr n c Ina ►it -rat e%.rt try, It MIN. ULH. L ACCOUSTICAL CEILING 1. EXISTING CEILING GRID USES #12 GAUGE ELEVATION Ll^*rV. -Mr' n A r'% I A ^r-L I" I.... I SPLAY — WIRE HANGERS GERS — AT 1 45 DEG. AND PAIL. UVUfN/VVUYV MAML W/MTL, STOP, PAINT ENAMEL 5/8" GYP. BD. 0/ MTL. STUD IIINNI Vu1-J11JL_ %JUL UT /--J/0 MLIAL Z)IUU3 5/8' TYPE Y GYP. BD. INSIDE SIDE OF 2-5/8' METAL STUDS 25 CA= le STUDS8 NOTE: At I f�-ri Ir%t- MMIPII Ir-%r- lAr-rAl VAL Mr. (MC) DEMATION MAX KT. tack DIMIGWON UP To Icr-e 12' UP m Is -a* Ir 3mm UP M 2-W lea 250=5 UP m 111-v 16" 358= Up To 2e 250(= UP m 91-8* 24:* 358=5 N- I I NUIbL BAHHILH GATT MAIN & CROSS RUNNER BEGINNING 48" FROM STARTING POINT (2) CONTI STRIPS DBL. FACE INSULATION WHERE OCCURS OF GRID AND TILE LAYOUT AND IN VINYL TAPE - TYPICAL + o METAL STUDS 0 0 BOTH DIRECTIONS @ 12'-0" THEREAFTER C:) + REFER TO FINISH PLAN FOR FLOOR & -0 3/8" MIN. CL.R ALL CLEARANCES.11ES TO WALL, ETC.TO METAL DOOR FRAME + 0 BASE SPECIFICATIONS CONFORM TO THE 1995 CBC SEC. 710-21 Lo 803, 1630, 2501, 2502 AND 2504 AND TOP OF FLOOR SLAB CONT. STUD CHANNEL - FASTEN TO C14 CONC. FLR. W/POWER DRIVEN FASTENERS O.C.AX. & 6u MAX. ENDS -TYP. @ 48n mg Ej 2. CEILING TILES ARE MINERAL TILES W/ c� = USE 'HILT!" OR EQ. SHOT PIN. APPROVED 0 0 0 UL LABEL AND HAVING A FLAME En ICBO FOR ALL SIZES NO. 2388, OR REDHEAD DOOR HARDWARE PER SCHEDULE + SPREAD OF 25 OR LESS. r'1 I ^r rIt'&' 1. - - - - ---% _ 20 CAUGE w mum MAX Mr. (O.Q) DEMATION MAX HOT. (O.Q DESIMMON IF 70 Iv_r Ir 2500= UP To 261-W 12" UP TO 12•-2 250= UP M 24W 16" 2e 12' 136 24" 500= 6000020 woock am= 8000C20 LIP, TO Vf__01 246 2500= UP TO 20!-0r LIP TO 11-W 120 356C= UP To 3r-Ir UP To I Ir-21 UP TO w-or UP TO 14W 24* 35aCC20 UP TO 2V-r Is Gwm W STUDS: MWMX H 0 T. (0.0 DEMIOTION MAX Kr. (MC.) DESMON UP TO Isel-e 120 358CaCin UP M 2Y--0' 24!' 600CC15 UP To i*r-e Ir 35=18 UP m W-51 Ir t3000CIs -UP M 14'-e 2e amis UP m V-50 le' 800CCis UP M 25'-T L2' W=le UP TO V-W 2e TO 25-e Ir f W=le I MANUFACTURER'S ASSOCIATION AND AFFILIATED MANUFACTURER'S ASSOCIATION AND AFFILIATED MANUFACTURER'S, ICBO NO 4943. ALL STUDS WILL BE SECTION TYPE -IC" (FOR 25 GA MATERIAL) OR "CC". THIS TABLE DESIGNATES STUDS FOR NON -BEARING INTERIOR WALLS ONLY. THE STUDS IN 117113 IMOLL MrNr- NU I M LUAULU AXIALLY ANU ARE LATERALLY UNBRACED. THE HEIGHTS ARE BASED ON WEB PUNCH -OUTS MINIMUM OF 1.3 TIMES THE WEB HEIGHT FROM THE EDGE OF BEARING. DEFLECTION LIMIT IS BASED ON L4240. A dk— m 3. EXISTING CEILING SUSPENSION SYSTEM I-011 I IS PER RR/22343 169-011 12 4 _011 7 00 e- EQ. EQ. I EQ. L 16 GWW 'cc' STUDS: (I MAX. tier.Ws"T" 1 MAX. Mr. MCI) OCRIMMON UP m 1jr-e 120 358mls UP m zy-r 2e 60=16 UP To 1r-40 lir 355= a UP To ar-e 12' UP TO IW-51 2e - 35=5 UP m V_e le SOOCCIa occia uP TO 30'--0• 3e 8=15 UP TO 2r-D' W=le I =GN 2915 FZDHU AVXNUE 1Rr]Hm3NG =1v a C COSTA 311111A. CUMRNU 92m 714ABa.SM C C I D C JEFFREY W. ADLER CERTIFIED INTERIOR aSIGNER 2049 EXPIRES 12-10-03 4W THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN AS AN INSTRUMENT OF PROFESSIONAL SERVICE IS THE PROPERTY OF BOLE' INTERNATIONAL AND IS NOT TO BE USED IN WHOLE OR PART FOR ANY PROJECT OTHER THAN THE ONE IDENTIFIED HEREIN WITHOUT THE WRITTEN AUTHORIZATION' OF BOLE INTERNATIONAL. THIS DOCUMENT SHALL NOT BE REPRODUCED OR MODIFIED IN ANY WAY WITHOUT THE EXPRESSED WRITTEN COHSE OF BOLE' INTERNATIONAL." REVISIONS: 912/03 - PROJECT START Rz 9/5103 - CITY SUBMITTAL 9/29/03 -CITY REVISIONS 0 il jr.ja Arna. !Ice of 10/1/03 -CITY RESUBMITTAL I ?a c! AN PARTICIPANTS, 11A DRAWN BY: C.P. CHECKED BY: F.J. DESIGNED BY: J.A. PROJECT INFO USABLE: 41,503 U.S.F. RENTABLE: PROJECT: JOB: OBSIDIAN ENT. DATE: SCALE: AS NOTED SHEET NAME DETAIL SHEET SHEET wi IN SUSPENDED CEILING DETAIL WINDOW BASE DETAIL SCALE: 3/32=1'-0n (I-CLSC-03.dwg) 3 SCALE: NTS 9 TYP, DOOR HEAD/JAMB SIM. METAL WALL STUD TABLE SCALE 30=10-00 5 SCALE: NTS1 A7.0