HomeMy WebLinkAbout235087_1_Corrections.docxRESIDENTIAL PLAN CHECK
COMMENTS
Planning & Building Agency
Building Safety Division
20 Civic Center Plaza
P.O. Box 1988 (M-19)
Santa Ana, CA 92702
(714) 647-5800
www.santa-ana.org
PLAN CHECK NO:
10194459
PROJECT ADDRESS:
412 1/2 E Camile St
PLAN CHECK ENGINEER:
Mazarji, ZacTEL:714
647-5831FAX:714
647-5897
TYPE OF CONSTRUCTION:
V B
OCCUPANCY CLASSIFICATION(S):
R-3, U
PLAN CHECK DATES:
REMARKS/RECHECK ITEMS:
APPLICATION
10/12/2017
ADU , accessory building unit.
INITIAL REVIEW
11/13/2017
EXPIRATION
4/10/2018
RECHECKS:
1.
PROJECT APPLICANT CONTACT PERSON:
2.
Frank Mitchell
3.
TEL:
(714)760-2397
FAX:
VALUATION: $43,600.00
EMAIL:
Frankfacts@yahoo.com
FLOOD ZONE: X-0602320276J
Based on following Codes: 2016 California Residential Code (CRC); 2016 California Building Code (CBC); CMC = 2016 California Mechanical Code; CPC = 2016California Plumbing Code; CEC = 2016 California Electrical Code; ICC = International Code Council.All items noted on this plan check report must be addressed. If you feel that an item is not applicable to your project, note “N/A” and discuss the reason with the plan checker.Please indicate the sheet number and detail to the right of each correction, or note the number on the plans where the correction is made. A separate sheet for response may be used.Please refer to red marks on the drawings for additional plan check comments and revise drawings to show compliance. Resubmit 3corrected sets of plans.Meetings between the project applicant/designer and the plan reviewer shall be by appointment only. Please call (714) 647-5831 for an appointment.
The applicant shall obtain clearances/approvals for the following, prior to building permit issuance:
- Planning Division approval on the corrected/final set of drawings (647-5804). Previously
approved plans should be submitted to expedite the process.
- Public Works Agency approval (647-5039).
- Fire Department approval on the corrected/final set ofdrawings) 714-573-6108)
- Proof of Worker's Compensation Insurance shall be required at the time of permit issuance.
Provide building information on plans:
- Occupancy type: R3 / U
- Construction type: Type V – B
- Fire sprinklered: Yes / No
Provide and show on the plans, house street number visible and legible from street. (Minimum 4”High x 1” Wide) CRC R319Show location of heating equipment on the plans. (CRC R303.8) Interior spaces intended for human occupancy shall be provided with heating facilities capable of maintaining a room temperature of 68 degrees Fahrenheit at a point 3 feet above the floor and 2 feet from exterior walls in all habitable rooms. (CRC R303.8). Please refer to red drawings for location of wall unit. Call out the efficiency and BTU rating of proposed unit/s. Show exhaust hood and exhaust vent above cooking appliances at the kitchen. (CMC 504.2) Show how the dryer will be vented to the outside air. (CMC 504.3) The maximum length of a dryer vent is 14 feet with two bends. Two feet shall be decreased for each bend more than two. (CMC 504.3.2.2) A dryer compartment shall be provided with a minimum opening of 100 square inches for makeup air in the door or by other approved means. (CMC 504.3.2)
Provide framing detail for new opening including 4x8 HDR. On the drawings, provide Nailing Schedule in conformance with CRC Table R602.3(1).
On the drawings, provide Nailing Schedule in conformance with CRC Table R602.3(1).Private garage shall be separated from the residence and its attic by a minimum ½ -in gypsum board applied to the garage side.Please refer to attached SB 407 and provide a copy of completed on the drawings.