HomeMy WebLinkAbout231781_2_Corrections.docxTENANT IMPROVEMENT
PLAN CHECK COMMENTS
COMMENTS
Planning & Building Agency
Building Safety Division
20 Civic Center Plaza
P.O. Box 1988 (M-19)
Santa Ana, CA 92702
(714) 647-5800
www.santa-ana.org
PLAN CHECK NO:
10193420
PROJECT ADDRESS:
1502 E Warner Ave
PLAN CHECK ENGINEER:
Mazarji, ZacTEL:714
647-5831FAX:714
647-5897
TYPE OF CONSTRUCTION:
III B
OCCUPANCY CLASSIFICATION(S):
B
PLAN CHECK DATES:
REMARKS/RECHECK ITEMS:
APPLICATION
7/3/2017
Commercial Solar panel system
INITIAL REVIEW
8/16/2017
EXPIRATION
12/30/2017
RECHECKS:
1.
PROJECT APPLICANT CONTACT PERSON:
2.
Rene Grigorian
3.
TEL:
(818)444-8888
FAX:
VALUATION:$32,000.00
EMAIL:
ara@olympicsun.com
FLOOD ZONE:X-0602320278J
Re-check: 12/11/2017Revised drawings and calculations submitted for Building Safety Division review is incomplete. The applicant shall, prior to resubmitting, complete all construction documents to show compliance with the 2016 California Building Standards Code.Refer to 1stplan check comments dated 8/16/17 and revise calculations and drawings to compliance.Calculations and drawings do not match. Calculations to show raised solar panels (wind load design) as shown on the drawings including itemizing actual dead load, live load. Please refer to two sets of calculations dated 11/20/17 and 2/28/17, pages 3 and 4 red flags (“Exceeds”) and revise calculations to reflect the actual existing framing of building including calculations for design and justification.Callout that existing building is one story with complete roof framing plan. Callout size, span and spacing of all roof members. Provide dimensions for existing roof plan. Subject to City inspection.
APPLICABLE CODE: 2016 CALIFORNIA BUILDING CODE (CBC) WITH
CITY OF SANTA ANA AMENDMENTS
All items noted on this plan check report must be addressed. If you feel that an item is not applicable to your project, note “N/A” and discuss the reason with the plan checker.Please indicate the sheet number and detail to the right of each correction, or note the number on the plans where the correction is made. Resubmit marked original, calculations and this correction sheet. A separate sheet for response may be used.Resubmit 3corrected sets of plans.Meetings between the project applicant/designer and the plan reviewer shall be by appointment only. Please call (714) 647-5831 for an appointment.This review does not include mechanical, plumbing, fire sprinkler system, or electrical work. Separate plans, applications, fees, plan checks, and permits are required for mechanical, plumbing, fire sprinkler systems, and electrical work. Call 647-5800 for information.Please remove MEP sheets.The applicant shall obtain clearances/approvals for the following prior to building permit issuance:
-Planning Division approval on the corrected/final set of drawings (647-5804.) Previously approved plans
should be submitted to expedite the process.
- Fire Department approval on the corrected/final sets of drawings (647-5839 or 647-5700)
- Public Works Agency approval (647-5039)
- Proof of Worker’s Compensation Insurance shall be required at the time of permit issuanceProvide dimensioned roof framing plan and identify roof each framing size and spacing. Submit structural calculations for each existing roof member due to additional load of solar panels. Incorporate results of calculations into drawings prior to re-submittal. Reference Sheet PV8, attachment detail of solar panels (identify detail number), Indicate spacing of 5/16” lag screws into existing roof members. Identify size of roof members where lag bolts are to be attached. Clarify if no angle solar panels (Flat) are installed per detail.Indicate ICC approved water sealant for 5/16 lag into existing roof on the drawings.