HomeMy WebLinkAbout313230_1_Corrections.docxTENANT IMPROVEMENT
PLAN CHECK COMMENTS
COMMENTS
Planning & Building Agency
Building Safety Division
20 Civic Center Plaza
P.O. Box 1988 (M-19)
Santa Ana, CA 92702
(714) 647-5800
www.santa-ana.org
PLAN CHECK NO:
101118469
PROJECT ADDRESS:
2525 W Westminster Ave Unit# I
PLAN CHECK ENGINEER:
Le, TungTEL:714
647-5896
EMAIL:
Tle10@santa-ana.orgFAX:714
647-5897
TYPE OF CONSTRUCTION:
V B
OCCUPANCY CLASSIFICATION(S):
B
PLAN CHECK DATES:
REMARKS/RECHECK ITEMS:
APPLICATION
3/4/2024
INITIAL REVIEW
3/9/2024
EXPIRATION
8/31/2024
RECHECKS:
1.
PROJECT APPLICANT CONTACT PERSON:
2.
Anthony Rodriguez
3.
TEL:
(626)288-6898
FAX:
VALUATION: $140,000.00
EMAIL:
anthony@garywang.com
FLOOD ZONE: X-0602320144J
APPLICABLE CODE: 2022 CALIFORNIA BUILDING CODE (CBC) WITH
CITY OF SANTA ANA AMENDMENTS
All items noted on this plan check report must be addressed. If you feel that an item is not applicable to your project, note “N/A” and discuss the reason with the plan checker.Please indicate the sheet number and detail to the right of each correction, or note the number on the plans where the correction is made. Resubmit marked original, calculations and this correction sheet. A separate sheet for response may be used.Resubmit 2corrected sets of plans.The applicant shall obtain clearances/approvals for the following prior to building permit issuance:
- Planning Division approval on the corrected/final set of drawings (647-5804.) Previously approved plans
should be submitted to expedite the process.
- Fire Department approval on the corrected/final sets of drawings ((714)573-6100)
- Police Department approval on the corrected/final set of drawings (647-5840)
- Public Works Agency approval (647-5039)
- County of Orange Health Department approval on the corrected/final set of drawings ((714)433-6000)An application for a permit for any proposed work shall be deemed to have abandoned / expired after 180 days of the date of filing, unless such application has been issued.Sheet G1.0: Please note no plan that “MEP are under separate plan review and approval”. Sheet G1.0: Please show size and location of the grease interceptor on the plan. Sheet G1.5: Detail 15 – Please revise detail to show 18” minimum clear to the centerline of the fixture. Sheet B1.0: Building Safety does not review and approve ADA standard details. Please remove and update details to show compliance with the 2022 California Building Code, Chapter 11B. CBC are more restricted for some requirement. Details shall be clearly cross-referenced onto the plan; non-applicable details shall be omitted/removed from the plan. Sheet A1.0: Floor plan – Please show dimensions for interior walls; show hallway dimension, show opening (see marked-up); clearance in kitchen work area, etc. Sheet A1.0: Wall Legend did not match with the wall type shown on the floor plan. Please revise wall legend to match. Referenced details 2, 4, 5, 6/A6.0: Please revise detail to show specify existing roof framing information. If trusses, please show soffit wall/ceiling attached to the top chord of trusses; and blockings as necessary. Sheet A1.0: Full height wall: Please provide construction detail for wall and clearly cross-reference detail onto the plan. Sale counter: Please provide/show accessible sale counter space. Provide detail and clearly cross-reference detail onto the plan. Walk in Cooler and freezer: Provide construction detail for the cooler. Show anchorage details. Sheet A1.0: Please clearly reference to sheet A4.0 for door schedule and door information. Door 101: Please specify door size and hardware. Door shall be accessible to persons with disabilities. Sheet A4.0: Please note – Egress doors/gates shall be readily openable from the egress side without the use of a key or special knowledge or effort. (1010.1.9)Openable parts of such hardware shall be 34 inches minimum and 44 inches maximum above the finish floor or ground. The force for pushing or pulling open a door shall be 5-lb maximum. Operable parts shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist. Detail 2 & 5 / A6.0: Please revise details to provide 7’-6” clear headroom. Type 1 hood: Provide structural calculation and details for hood support and roof top equipment.
(End of Comment)