Laserfiche WebLink
Exhibit 2 <br />12.5.1 After raking/shoveling loose material from high spots back into low spots/worn <br />areas on running paths, sliding zones, and any other low spots/worn areas appearing <br />on the field, the Contractor shall fill all remaining low spots with new Stabilizer <br />Solutions Stabilizer Gold Infield Mix (with stabilizer). brickdust from stock and <br />make level. <br />12.5.2 The contractor shall clean all excess brickdust beneath or next to the backstop; <br />dugout chain link fencing and/or infield chain link fence lines so that the infield <br />brickdust is level with the dugout pavement and pavement outside the infield. <br />12.5.3 Lightly water entire infield before dragging. Note: Watering shall penetrate <br />brickdust to a minimum depth of 1/8" deep min. This process is crucial to keeping <br />brickdust in place and not going air borne. <br />12.5.4 Drag infield utilizing small utility vehicle as specified with "grooming or finishing <br />drag". Circular or figure eight drag patterns shall be used (see details 1-A & 1-13). <br />Alternate drag patterns or reverse direction of drag patterns daily to avoid ruts and <br />high/low areas. Speed of drag procedure shall not exceed 7 mph. <br />12.5.5 When dragging the skinned infield, the contractor shall stay away from all turf <br />edges a minimum of 18". This will help in avoiding lips at brickdust/turf edges. <br />This 18' gap shall also apply to all backstops and chain link fence areas. <br />12.5.6 Contractor shall hand rake all base paths on combination turf/brickdust infields. <br />12.5.7 When the dragging process is complete, the contractor shall stop the drag in a <br />different location daily. This will stop the accumulation of brickdust in focused <br />areas. At this time roll -up the drag, place it on the vehicle and remove all debris <br />accumulated in the drag at this spot and rake out material emptied from drag. <br />12.5.8 After dragging, hand rake the 18" edges using the "grade or grooming rake". The <br />rake shall be held at an angle as to not push brickdust onto/into turf areas. <br />12.5.9 After raking the 36" edges, the contractor shall clean all excess brickdust on the <br />turf edges utilizing a high pressure water nozzle or heavy duty broom. NO <br />brickdust shall be permitted on the turf edges at any time. If in the determination of <br />City staff, an unsafe lip situation exists (an unsafe lip is ''/z" or greater) in any <br />turf/brickdust border area infield to brickdust, base -paths or brickdust to outfield), <br />contractor will be required to remove or level the soil build-up with a sod cutter and <br />re-establish the in -field boundaries with a string line or suitable method and re -sod <br />up to the border to remedy the situation at contractors expense. Pre-existing <br />conditions shall be corrected during contract start-up. <br />12.6 Final Watering <br />12.6.1 This is the most time consuming and a very important element of the procedure. <br />12.6.2 The contractor shall final water the skinned brickdust to a depth of/d' minimum. <br />13.0 Rainy Weather/Wet Field Procedure <br />13.1 On the next scheduled working day after a rainfall, the following procedure, in the order <br />listed, shall be adhered to: <br />13.1.1 Remove all standing water from low spots either by skimming off excess water and <br />spreading it out to dry areas or using a pump/sopper system. <br />13.1.2 Rake out (scarify) wet areas. <br />13.1.3 Apply Stabilizer Solutions Stabilizer Gold Infield Mix (with stabilizer) from stock <br />to all Wet Areas and Rake Out. Cap with calcified clay Turface. <br />City of TAPPg3119-093 <br />p'� 1 �+ <br />