Laserfiche WebLink
FEE SCHEDULE <br />MASTER FEE SCHEDULE <br />CITY OF SANTA ANA <br />ON -CALL GEOTECHNICAL, SPECIAL INSPECTION & MATERIAL TESTING SERVICES <br />NOT TO EXCEED $25,000.00 WITHOUT PRIOR AUTHORIZATION <br />Prestressing Steel Tests a <br />Description Unit Rate Unit Description Unit Rate Unit <br />Yield Strength, Breaking Strength, Elongation $ 300.00 Each <br />(add $ 25.00 per test; for Modulus of Elasticity) <br />Breaking Strength Only $ 195.00 Each <br />Fireproofing Tests <br />Fireproofing Adhesion/ Cohesion Test Kit ASTM E736 <br />Fireproofing Density Test ASTM E605 <br />Miscellaneous <br />Description <br />$ 45.00 Each <br />$ 35.00 Each <br />Unit Rate Unit <br />Pull -Off Strength ofCoa0ngs ASTM D4S41 <br />$ 40.00 Per Set <br />Tensile Properties of Polymer Matrix Composite Materials <br />$ 650.00 Each <br />ASTM D3039 <br />Concrete Mix Design Review <br />$ 150.00 Each <br />Preparation of WPS, FOR, or Welder Certificate <br />$ 150.00 Hour <br />Welder Qualifications <br />$ 150.00 Hour <br />Weld Procedure Review <br />$ 150.00 Hour <br />Certified Payroll Compliance <br />$ 100.00 Week <br />Outside Services/Reimbursables <br />Cast +15% <br />Shipping Charges <br />Cost+ 15% <br />Parking/Tolls <br />At Cost <br />Deputy Inspectors <br />Travel Time (Beyond 75-Mlle Radius of Project Site) <br />$ 50.00 Hour <br />Per -diem, Including Lodging (Beyond 75-Mile Radius) <br />Quote Upon Request <br />Nuclear Gauge Transportation Fee (if Not Stored Onsite) <br />Portal to Portal <br />Skidmore Wilhelm- Bolt Tension Equipment <br />$ 95.00 Day <br />Sample Pick -lip <br />$ 50.00 Trip <br />Work from D4 hours <br />4-Hour Minimum Billing <br />Work from 4-8 hours <br />8-Hour Minimum Billing <br />Work over 8 hours per day, or on Saturdays <br />Time and One -Half <br />Work over 12 hours per day <br />Double Time <br />Work on Sundays/Holidays <br />Double Time <br />Show -Up Time <br />2-Hour Minimum Billing <br />Shift Differential <br />$ 10.00 Hour <br />Same Day Callout <br />Time and One -Half <br />Personnel are billed in four (4) houraM eight (8) hour blocks. Work over eight (81 hours per day, the first twelve (12) hours of work on Saturday, and work over forty (40) hours perweek is billed at 1.5 <br />times the above hourly rates. Any work over twelve (12) hours on Saturdays and work performed on Sundays or holidays is billed at 2.0 times the above hourly rates. Requested services which are <br />required to be subcontracted by Unked-Heider Inspection Group will be billed at cast plus fifteen percent (15%). A two(2) hour minimum is billed forcencellation of Inspection person col less than faur14) <br />hours in advance of the scheduled Inspection time. Steel fabrkatlon shop inspection that Is required at a distance greater than fifty (50) miles From our Riverside, California office will have billable trawl <br />costs including, but not limited to, commercial transportation at cost plus fifteen percent (15%), vehicle mileage at the above rate, travel time at the Inspector's hourly rate, and Per them expenses not to <br />exceed $120.00 per day. Approximately one (1) hour of engineering (registered geotechnicxl engineer for wik inspections and certified engineer for all other types of Inspections( Is billed for every fort, <br />(40) hours of Reid inspection time. Delinquent Invoices may bs subject to Interest service charges, and collection expenses, including attorney's fees, at our discretion. Interest is assessed at a rate of <br />0.03291%per day (12%annually) for each day the Invoice is past due. The date an Invoice Is due Is determined to be the Invoice date plus thirty (30) days. <br />Escabtlon In Prevailing Wage hourlyrates will be calculated using the percentage of Innease Issued by the State ojColUbmia Director of IndusMal RebWns <br />CITY OF ANA ON -CALL GEOTECHNICAL, SPECIAL INSPECTION AND MATERIALS TESTING SERVICES 21 <br />