My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
Agenda Packet_2022-12-20
Clerk
>
Agenda Packets / Staff Reports
>
City Council (2004 - Present)
>
2022
>
12/20/2022 Special & Regular
>
Agenda Packet_2022-12-20
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
12/22/2022 9:48:29 AM
Creation date
12/20/2022 10:03:01 AM
Metadata
Fields
Template:
City Clerk
Doc Type
Agenda Packet
Date
12/20/2022
Jump to thumbnail
< previous set
next set >
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
1209
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
View images
View plain text
SERVICE AGREEMENT — ALL INCLUSIVE 100% WARRANTY <br />• Check and drain inlet filters <br />• Check valve sequencing <br />• Visually inspect all pressure relief devices for signs of failure or leakage <br />• Verify ESD control functions and safety equipment <br />• Verify on/off switch operations <br />• Verify ESD control functions <br />• Verify 4,250-psig maximum fill pressure limits <br />Dispensers — Time Fill <br />• Visually inspect tubing, piping, and valves for leaks and abnormalities <br />• Check and drain inlet filters <br />• Verify ESD control functions and safety equipment <br />Methane Gas Detection Sensors <br />• Verify and test operations <br />• Test equipment to meet OEM design criteria <br />• Repair and replace defective equipment <br />Inlet Gas Dryer <br />• Monthly — Drain pre -filter, blower house, and sump <br />• Monthly — check differential pressure across pre -filter and after -filter elements. Replace if <br />required when gauge is approaching red zone or 3-5 PSID <br />• Monthly — check dewpoint for reading below -40F. If above, then regenerate dryer <br />• Monthly — check and maintain operating conditions: pressure, flow, temperature within the design <br />of parameters of the dryer. <br />• Six Months — recalibrate/check span of moisture analyzer <br />• Six Months — replace pre -filter, after -filter, and separator elements if needed <br />• Annually — regenerate dyer, check regeneration cycle to ensure working properly <br />• 1000 Hours — change oil in blower <br />2000 Hour Intervals <br />• Post compression coalescing filter element replacement <br />• Compressor frame oil replacement (crankcase oil) <br />• Compressor frame oil replacement (crankcase oil filter) <br />• Compressor oil strainer element cleaning <br />• Force feed lubricator box lube oil replacement <br />• Force feed lubricator filter replacement <br />• Compressor interstage coalescing filter element replacement <br />• Driver motor lubrication (grease bearings per manufacturers recommendations) <br />3000 Hour Intervals <br />• Post compression coalescing filter element replacement <br />4000 & 8000 Hour Intervals — Compressor Rebuild <br />• Post compression coalescing filter element replacement <br />• Compressor frame oil replacement (crankcase oil) <br />• Compressor frame oil replacement (crankcase oil filter) <br />• Compressor oil strainer element cleaning <br />• Force feed lubricator box lube oil replacement. <br />10225 Philadelphia Court One North Lexington Ave 35577{0�g8c11st Street NW <br />Ranch 1 ymp{igaUnd ie ains, 1 - 64 12d U/LU 55960 <br />
The URL can be used to link to this page
Your browser does not support the video tag.