Laserfiche WebLink
1 <br />DOOR BOARDING SPECIFICATIONS <br />-- 111.' Cox PLYWOOD <br />CUT TO FIT AGAINST <br />DOOR SANO MOLDING OR <br />OIfTSIDE OF DOOR FRAME <br />i <br />1-w----------------�--w� <br />1 <br />! <br />1 <br />i <br />1 <br />r <br />1 <br />i <br />1 <br />r <br />1 <br />+ <br />■ TOP ■ <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />t <br />r <br />1 <br />1 <br />1 <br />1 <br />1 <br />+ <br />1 <br />1 <br />I <br />+ <br />■ CENTER ■ <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />it- <br />1 <br />■ soTrom t <br />1 <br />1 <br />1 <br />1 <br />L—' <br />1 <br />1 <br />1 <br />EL -- <br />2X4 8RAC£9 <br />CUT TO SIZE OF <br />PLYWOOD <br />102' CO% PLYWOOD — 1. <br />CUT TO COVER DOOR 1 <br />FRAME AND MOLDING ` <br />■r---------------------- <br />r <br />1 <br />1 <br />1 <br />1 <br />1 <br />f <br />1 <br />e <br />+ <br />r <br />t <br />r <br />+ <br />1 <br />1 <br />! <br />1 <br />r <br />1 <br />t <br />1 <br />+ <br />1 <br />f <br />1 <br />� <br />1 <br />1 <br />1 <br />1 <br />1 <br />1 <br />+ <br />t <br />1 <br />t <br />1 <br />! <br />1 <br />r <br />l <br />t <br />1 <br />1 <br />1 <br />r <br />1 <br />1 <br />1 <br />r <br />1 <br />e <br />r <br />r <br />1 <br />90"c« wAck • of w <br />` YB' CARRIAGE BOLT - - - I I <br />DOOR — OUTSIDE VIEW — WITH 1r2'WASHER DOOR - INSIDE VIEW <br />REMOVE TRIM AS <br />NECESSARY TO <br />ELIMINATE PRY POINTS 1 <br />12' LONG ye' - <br />CARRIAGE SOLT <br />WITH 1f7 WASHERS <br />ON BOTH SIDES <br />T <br />NOTES: <br />1. IRON DOORS OR FRAMES MAY BE REMOVED AND STORED INSIDE BUILDING IF <br />NECESSARY. <br />2. USE 3/8" X 12" CARRIAGE BOLTS - ROUNDED HEAD ON OUTSIDE OF BUILDING. <br />LONGER BOLTS MAY BE NECESSARY. <br />3. TIGHTEN NUTS FROM INSIDE ENOUGH TO SLIGHTLY COMPRESS 2X4 BRACE. <br />4. IF PLYWOOD CAN NOT BE BUTTED AGAINST BAND MOLDING, CUT TO COVER <br />OUTSIDE EDGE OF DOOR FRAME. <br />5. BOLT HOLES ARE LOCATED AS THEY ARE FOR WINDOWS (SEE WINDOW DETAIL) <br />6. CENTER BRACE LOCATED IN CENTER OF DOORWAY OPENING. TOP AND BOTTOM <br />BRACES ARE POSITIONED WHERE A = 1/213 (SEE DIMENSION LOCATIONS ON <br />DRAWING) <br />7. USE 2X4 BOTTOM BRACE - CUT TO WIDTH OF DOOR TRIM. DRILL TO THE FLOOR <br />TO PREVENT OPENING. INTERIOR AND EXTERIOR BOTTOM BRACES WITH <br />MASONRY SCREWS ARE MANDATORY WHEN BOARDING GARAGE DOORS. <br />City of Santa Ana RFP 22-068 <br />Page 15 <br />