Laserfiche WebLink
<br />LDVlJ? <br /> <br />I <br /> <br />LDV, inc. <br />180 Industrial Drive <br />Burlington, WI 53105 <br />800.558.5986 <br />Fax 262]63.0156 <br />www.ldvusa.com <br /> <br />Section Qty <br /> <br />8.03 1. Fresh water/waste tank level monitor in galley area. <br />2. Stainless steel galley sink with chrome plated sink hardware. <br />3. Aqua Jet model #5503-AV15-B636 (or current model) 5.3 GPM water pump with accumulator <br />tank. <br />4. One (1) 30 gallon fresh water supply and one (1) 35 gallon waste tank. <br />. 5. All plumbing pressure pipes shall be CPVC. <br />! 6. Underbody fresh water and grey water tanks are to be heated and all plumbing insulated and <br />wrapped with heat tape. <br />7. Sewage hose and dump valve shall be provided for holding tank. <br />8. Regulated city water fill so that system can be pressurized using city water when available. <br />9. Winterizing valve mounted in line on the input side of the water pump. Valve allows antifreeze to <br />be pumped throughout the system to winterize plumbing. <br />8.04 1 Minimum 0.9-cu.II. 900-watt microwave oven. <br />8.05 2 Black & Decker model ODC325 (or current model) under-cabinet coffee maker. Located as shown <br />on drawing. <br /> <br />8.06 <br /> <br />8.07 1 <br />8.08 1 <br />9.00 <br />9.01 5 <br />9.02 2 <br />9.03 <br />9.04 <br /> <br />10.00 <br /> <br />Norco/d model DE-0051 (or current model) 12Vdc/120Vac refrigerator with the following features: <br />.2.7 cu. II. capacity. <br />. Freezer shelf for ice cube tray. <br />. Two door bins; lower bin holds 2-liter containers. <br />. Integrated door latch. <br /> <br />External hatch with shower head and hoUcold faucet. <br />Hot and Cold Countertop Water Dispenser. <br />SEATING: <br />Hon ValueTask@swivel chair model 5831 (or current model) with mid back, five caster spider base, <br />adjustable height and armrests (color - to be determined). <br />Custom fabricated sliding pedestal for desk chair. Located as shown on drawing. <br />Fabricate and install fixed bench seating with removable cushions as shown on drawing. <br />1. Bench seat cushions shall be covered in heavy-duty cloth with vinyl sides (color - to be <br />determined). <br />1. Foam for seat backs and bottoms shall have a minimum density rating of 28, a minimum <br />compression rating of 65 and a support factor of 2.2. <br />2. All bench seating material must meet Federal Motor Vehicle Safety Standards part 571.302 <br />Flammability of Interior Materials. <br />3. Seam stitching shall be done with 8-oz. bonded nylon thread. <br />4. Material corners shall be squared or angled to fit precise cut of foam. <br />5. Foam shall be bonded to plywood backer with industrial grade elastomer adhesive. <br />6. Bottom and sides of plywood backer shall be completely sanded. <br />7. Stapling of fabric/vinyl to backer with industrial grade upholstery staples. <br />8. No more than a 1/2" space is acceptable between staples around the entire perimeter. <br />9. All fabric shall be stain resistant. <br />CABINETS: <br /> <br />8 <br /> <br />Santa Ana Police Department (CA) MGC30LLC260-03.3 RZ.xls <br /> <br />1/28/2005 <br />