Laserfiche WebLink
<br />Attachment B <br /> <br />LDva LDV, Inc. <br />180 Industrial Drive <br />Burlington, WI 53105 <br />800.558.5986 <br />Fax 262.763.0'56 <br />www.ldvusa.com <br />Section Qty <br />8.03 1. Fresh water/waste tank level monitor in galley area. <br /> 2. Stainless steel galley sink with chrome plated sink hardware. <br /> 3. Aqua Jet model #5503-AV15-B636 (or current model) 5.3 GPM water pump with accumulator <br /> tank. <br /> 4. One (1) 30 gallon fresh water supply and one (1) 35 gallon waste tank. <br /> 5. All plumbing pressure pipes shall be CPVC. <br /> 6. Underbody fresh water and grey water tanks are to be heated and all plumbing insulated and <br /> wrapped with heat tape. <br /> 7. Sewage hose and dump valve shall be provided for holding tank. <br /> 8. Regulated city water fill so that system can be pressurized using city water when available. <br /> 9. Winterizing valve mounted in line on the input side of the water pump. Valve allows antifreeze to <br /> be pumped throughout the system to winterize plumbing. <br />8.04 1 Exterior hatch with shower head and single lever faucet 14122 (or current model), shower has 6' <br /> hose. <br />8.05 1 Minimum 0.9-cu.ft. 900-watt microwave oven. <br />8.06 2 B/ack & Decker model ODC325 (or current model) under-cabinet coffee maker. <br />8.07 1 Norco/d model DE-0051 (or current model) 12Vdc/120Vac refrigerator with the following features: <br /> .2.7 cu. ft. capacity. <br /> . Freezer shelf for ice cube tray. <br /> . Two door bins; lower bin holds 2-liter containers. <br /> . Integrated door latch. <br />8.08 1 Countertop water dispenser with hot and cold faucets, includes removable or hinged shelf above <br /> water bottle. <br />9.00 SEATING: <br />9.01 5 Hon ValueTask@ swivel chair 5831 black (or current model) with mid back, five caster spider base, <br /> adjustable height and armrests. <br />9.02 2 Custom fabricated sliding pedestal for desk chair. Located as shown on drawing. <br />9.03 Fabricate and install fixed bench seating with removable cushions as shown on drawing. Bench <br /> seat cushions shall be covered in heavy-duty vinyl (color - to be determined). <br />9.04 BENCH SEAT REQUIREMENTS: <br /> 1. Foam for seat backs and bottoms shall have a minimum density rating of 28, a minimum <br /> compression rating of 65 and a support factor of 2.2. <br /> 2. All bench seating material must meet Federal Motor Vehicle Safety Standards part 571.302 <br /> Flammability of Interior Materials. <br /> 3. Seam stitching shall be done with 8-oz. bonded nylon thread. <br /> 4. Material corners shall be squared or angled to fit precise cut of foam. <br /> 5. Foam shall be bonded to plywood backer with industrial grade elastomer adhesive. <br /> 6. Bottom and sides of plywood backer shall be completely sanded. <br /> 7. Stapling of fabric/vinyl to backer with industrial grade upholstery staples. <br /> 8. No more than a 1/2" space is acceptable between staples around the entire perimeter. <br /> 9. All fabric shall be stain resistant. <br />10.00 CABINETS: <br /> <br />Copy of Huntington Beach Police Department (CA) MCC30LLC260-0:B2 MS.xls <br /> <br />6/16/2005 <br />