Laserfiche WebLink
SEE! <br />High Purity Solutions <br />Standard Products <br />consecutively (Primary vessel, Secondary vessel, then, Tertiary vessel). When a vessel is <br />being regenerated, the remaining two vessels will be in Service mode. After completion <br />of the Regeneration Cycles, the vessel assignment will return to the state they were in <br />prior to the initiation of the Regeneration Cycle. <br />SYSTEM DESIGN SPECIFICATIONS <br />The design specifications for the PTI series softeners are listed in this section. <br />PRODUCT OFFERING OVERVIEW: <br />** While operating in a 2 to 1 mode, the flow rates match a duplex unit. While operating in a progressive flow mode, the minimum flow <br />*** Flow rates maybe limited to 20 gpm/sqft. <br />DESIGN PARAMETERS: <br />Configuration <br />Plus Deluxe, and Select <br />Product <br />Flow Rates (ppm) <br />Triplex <br />Min. Flow (2 gpmisgft) <br />Best Flow (3 gpmlcuft) <br />Better Flow <br />(5 gpmlcuft) * ** <br />Good Flow (7 gpmlcuft) * ** <br />Model Number <br />Simplex <br />Duplex* <br />Triplex ** <br />Simplex <br />Duplex* <br />Triplex ** <br />Simplex <br />5 gpm /ft3 (Limited by 20 gpm/ftz for 84" dia and larger) <br />riplex — <br />Simplex <br />Duplex* <br />Triplex ** <br />PT.I$ <br />72X72 <br />57 <br />- 113 <br />170 <br />297 . <br />-: 594 <br />89.1 <br />495 <br />30,000 grains /ft3 <br />Regeneration <br />665 <br />1131 <br />1696 <br />PTIS <br />84X84 <br />77 <br />154 <br />231 <br />471 <br />942 <br />1413 <br />770 <br />A2011 <br />770 <br />1539 <br />2309 <br />PTI$ <br />96X36 <br />101 <br />.;,.201 <br />30'2 <br />708 <br />,:1416 <br />214 <br />'1005:_' <br />E4712 <br />1005 <br />2011 -` <br />3016 <br />_. <br />1571 <br />1571 <br />3142 <br />4712 <br />* Whil, nneratino in a duplex Ao,'rn.n" mode. the product <br />flow rates are the <br />same as a simplex unit. <br />** While operating in a 2 to 1 mode, the flow rates match a duplex unit. While operating in a progressive flow mode, the minimum flow <br />*** Flow rates maybe limited to 20 gpm/sqft. <br />DESIGN PARAMETERS: <br />Configuration <br />Simplex <br />Duplex <br />Triplex <br />Feed Temperature <br />60 °F <br />Feed Pressure <br />45 psig <br />Maximum Inlet Turbidity* <br />5 NTU (Nephelometric Turbidity Units) <br />Maximum Inlet TDS* <br />750 ppm as CaCO3 (29.2 grains /gallon) <br />Sizing: <br />Service Flow Rate <br />3 gpm /ft3 <br />5 gpm /ft3 (Limited by 20 gpm/ftz for 84" dia and larger) <br />7 gpm/ft3 (Limited by 20 gpmi in all cases) <br />Backwash Flow Rate <br />Adjustable via valve travel stops <br />Rinse Flow Rate <br />1.5 gpm/ft3 <br />Bed Depth <br />42" — 56" <br />Freeboard <br />54 % -57% of the tank side sheet volume <br />Resin <br />Siemens C -21 1B cation resin, 8% cross - linked <br />Capacities <br />30,000 grains /ft3 <br />Regeneration <br />15 Ibs (dry) NaCI per fit' (5.77 gallons of saturated NaCl/ ft') <br />Support Bed <br />3" depth of 94 quartz (1.54mm average size) <br />2" over laterals - /4 x I/V quartz <br />* Ifprocess is not within the given limit, then contact applications engineeringfor assistance. <br />PTI Series Softeners Page 4 Rev. 1, February 2009 <br />S5131 -020 251-54 <br />