T.I.'S BY DESIGN - Laserfiche WebLink

Home Browse Search

Submittal cm Package I Viega ProPress"' Ball Valves For TvDes K. Land M Hard Cower Tubloica in 1/211 to 2T_vriid v a nar Ti ilainx in 1/911 tat I IIA" ProPross Insertion Depth Chart I Tube Size 1.1 11/' 1. 1 1W, "I Read and understand all instructions for installing Illegal ProPress fittings, Failure to follow all instructions may result in extensive property damage, serious injury or cleaft 1. Cut copper tubing at right angles using displacement - type cutter or fine-toothed steel saw. 2. Remove burr from inside and outside of tubing to prevent cutting sealing element. 3. Check seal for correct fit. Do not use oils or lubricants. Use only Viega ProPress Shiny Black EPDM or Dull Black FKM sealing elements. Note: For applications requiring Viega ProPress with FKM sealing elements, remove the factory -Installed EPDM sealing element and replace with FKM sealing element, 4. Mark proper insertion depth as indicated by the Viega ProPress Insertion Depth Chart. Improper insertion depth may result in improper seal, 5. While turning slightly, slide ball valve onto tubing to the marked depth. Note: End of tubing must contact stop. 6. Insert appropriate Viega jaw into the pressing tool and push in, holding pin until it locks in place, 7. Open the jaw and place at right angles on the valve. Visually check insertion depth using mark on tubing. 8. Start pressing process and hold the trigger until the jaw as engaged the valve. 9. After pressing, the jaw can be opened again. Note: Only ball valves marked with NSF -610 are allowed for use in potable water systems. Leak Testing with Smart Connece- Unpressed connections are located by pressurizing the system with air or water. When testing with water the proper pressure range is 15 psi to 85 psi maximum. Leak testing with air can be dangerous at high pressures. When testing with compressed air the proper pressure range is 1/2 psi to 45 psi maximum. Following a successful leak test, the system may be pressure tested tip to 200 psi with air, or up to 600 psi with water, if required by local code requirements or project specifications, Vlega LLL, 12303 Airport Way, Ste. 395 - Broomfield, CO 80021 ® lsh: 800-976-9819 % Fax; 800-976-9817 SM -PP 1116 (Ball Valves) is Of 16 fill 6 7 ProPross Insertion Depth Chart I Tube Size 1.1 11/' 1. 1 1W, "I Read and understand all instructions for installing Illegal ProPress fittings, Failure to follow all instructions may result in extensive property damage, serious injury or cleaft 1. Cut copper tubing at right angles using displacement - type cutter or fine-toothed steel saw. 2. Remove burr from inside and outside of tubing to prevent cutting sealing element. 3. Check seal for correct fit. Do not use oils or lubricants. Use only Viega ProPress Shiny Black EPDM or Dull Black FKM sealing elements. Note: For applications requiring Viega ProPress with FKM sealing elements, remove the factory -Installed EPDM sealing element and replace with FKM sealing element, 4. Mark proper insertion depth as indicated by the Viega ProPress Insertion Depth Chart. Improper insertion depth may result in improper seal, 5. While turning slightly, slide ball valve onto tubing to the marked depth. Note: End of tubing must contact stop. 6. Insert appropriate Viega jaw into the pressing tool and push in, holding pin until it locks in place, 7. Open the jaw and place at right angles on the valve. Visually check insertion depth using mark on tubing. 8. Start pressing process and hold the trigger until the jaw as engaged the valve. 9. After pressing, the jaw can be opened again. Note: Only ball valves marked with NSF -610 are allowed for use in potable water systems. Leak Testing with Smart Connece- Unpressed connections are located by pressurizing the system with air or water. When testing with water the proper pressure range is 15 psi to 85 psi maximum. Leak testing with air can be dangerous at high pressures. When testing with compressed air the proper pressure range is 1/2 psi to 45 psi maximum. Following a successful leak test, the system may be pressure tested tip to 200 psi with air, or up to 600 psi with water, if required by local code requirements or project specifications, Vlega LLL, 12303 Airport Way, Ste. 395 - Broomfield, CO 80021 ® lsh: 800-976-9819 % Fax; 800-976-9817 SM -PP 1116 (Ball Valves) is Of 16