10193154 - Permit (3) - Laserfiche WebLink

Home Browse Search

SIA]E OF CALIFORNIA ENERGY MANAGEMENT CONTROL SYSTEM OR LIGHTING CONTROL SYSTEM @cEc-NRCt-LTl{2-E 12t1 CALIFORNIA ENERGY COMMISSION CERTIFICATE OF INSTATLATION NRCI-tTt-02-E EnerSy Management Control System or Lighting Control System {(*v*'1";â‚¬ftrdd^-f 4 L<--..-..,-* 6L),,*.ua.-, -t-1.,.( il. fiAdhn ,'\?;-1"2/9-: Ef 1- Automatic Oaylight Controls meet all requirements for Automatic Daylight Control devices in the Title 20 Appliance Efficiency Regulationt including the followlng: a. ls capable of reducing the power consumption in response to measured daylight either directly or by sending and receivint signals; b. lf the system includes a dimmer, complies with the Dimmer Control device requirements in the Title 20 Appliance Efficiency ReSulations. c. Automatically return to its most recent time delay settings within 60 minutes when put in calibrauon modc; d. Hasa set point controlthat easily distinguishes settings to within 10 percent offull scale adjustment; e. Has a light sensor that has a linear response within 5 percent accuracy over the range of illuminance measu.ed by the light sensor; f. Has a light sensor that is physically scparated from where the calibrdtion adjustments are made, or is capable of beint calibrated in a manner that the person initiatinS the calibration is remote from the 5ensor during calibration to avoid influenclng calibration accuracy; and 8. Complies with the Title 20 requirementsfor photo controls if the system contalns a photo control component. Q/ z. enoto controls meet all requirements for Photo control devices in the Title 20 Appliance Efficiency Regulations, including the followinS that it does not have a mechanical device that permits disablint of the control. G. The EMCS or LiShting Control System functions as a Dimmer and meets all requirements for a Dimmer Control device in the Title 20 Appliance Efficiency Regulations, including the following: 1. ls capable of reducing power consumption by a minimum of 55 percent when the dimmer is at its lowest level; 2. lncludes an otf position which produces a zero lumen output; and 3. Does not consume more than l watt per lighting dimmer switch leg when in the off position. 4. Dimmer controls that can directly control lamps provide electrical outputs to lamps for reduced flicker operation throu8h the dimming range so that the liSht output has an amplitude modulation of less than 30 percent for frequencies less than 200 Hz without causing premature lamp failure. 5. lf designed for use in three wav circuits is capable ofturning lights off, and to the level set by the dimmer if the liShts are off. tr H. The EMCS or Lighting Control System meets the following requirements: 1. ls capable of automatically turning off cohtrolled lights in the area no more than 30 minutes after the area has been vacated; 2. Allows all liShts to be manually turned off regardless of the status of occupancy; and 3. Has a visible status rignal that indicates that the device is operating properly, or that it has ,ailed or malfundioned. The virible status signal may have an override switch that turns offthe signal. 4. All occupant sensing devices that utilize ultrasonic radiation for detedion of occupants meet the Ultrasound Maximum Decibel Values in the Title 20 Appliance Efficiency Regulations 5. All occupant sensing devices that utilize microwave radiation for detection of occupants meet the r.diation requirements in the Title 20 Appliance Etficiency Regulations 6. Occupant sâ‚¬nsing devices incorporatinS dimming comply with the requirements for dimmer controls in the Title 20 Appliance Efficiency Regulations C-A BuildinB Energy â‚¬fficiency Standards 2013 Non16idential Compliance De.ember ?O15 (Page 3 of 5)