10179147_2140 E. 17TH - Plan - Laserfiche WebLink

Home Browse Search

47 SIGN COMPONENTS MANUAL (SAM)November 14,2012 LED 10CV 24 PU LED 10CC 350,120-240 0.175-0.120 2.3-28 0.350 10 VA LED 10CC 350 PU 2. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output. 3. A suitable Fire and Electrical Enclosure shall be provided in the end product. 4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 5. These power supplies are only suitable for use in dry and damp locations. Class 2 Power Supply, Models LED 60CV 12P, LED60CV 24P, LED 100 CV 8, LED 100 CV 12, LED 100 CV 24, LED 100 CV 48. 1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output. 2. The electrical ratings are as follows: Input, 60 Hz. Output DC Model V A V VA LED 100 CV 8 100 - 277 1.3 - 0.5 8 100 LED 100 CV 12 100 - 277 1.3 - 0.5 12 100 LED 100 CV 24 100 - 277 1.3 - 0.5 24 96 LED 100 CV 48 100 - 277 1.3 - 0.5 48 96 LED 60CV 12P 100 - 277 0.8 - 0.3 12 60 LED 60CV 24P 100 - 277 0.8 - 0.3 24 60 3. These power supplies are only suitable for use in dry and damp locations. 4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Company name or trademarks lightech™ Ughtech TIe 4 LED Driver / Hclogen Tran,forrnei, and model designation. 'GE LIGHTING SOLUTIONS LLC6/< BLDG 338E 1975 NOBLE RD EAST CLEVELAND, OH 44112 USA E219167 Border tube kits, Includes Lens Cat. No. GExxBTL; Lens connector Cat. No. GE=BTLC; End cap Cat. No. GE=BTLEC; ED<terior corner kit Cat. No. GExxBTLXC; Interior corner kit Cat. No. GE=BTLIC; Base reflector Cat. No. GEBTBR; Base connector Cat. No. GEBTBC; Cam lock Cat. No. GEBTCL. Canopy Kits, Cat. No. GECPL (8 ft length), GECPEC (end cap), GECPLC, (lens connector), GEBTBCL, GEBTBC. Light guide kits includes: Light guide Cat. No. GEXNLGXX-XXX, Light Guide End Cap Cat. No. GEXXXNLGECZZ, XXX may be any alpha letter representing color. ZZ may be any alpha letter representing size. Light Guide Connector Cat. No. GEXXXNLGYZZ, XXX may be any alpha letter representing color, Y can be any alpha character describing the type of connector. ZZ may be any alpha letter representing size.. Mounting clip Cat. No. GEXNMCXX; Supply wire Cat. No. GEXNSXX, Splice connector Cat. No. GEXNSC1; Weather box Cat. No. GEXWBXX-XXX. 1. Border Tube Kit, Canopy Kit and Light Guide Kit are for Wet Location only use when enclosing LED's connected to a Class 2 circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. 2. The LED border tube kit and Canopy Kit was not evaluated as an electrical enclosure. 3. The LED border tube kit and Canopy Kit was not evaluated as a watertight housing. LED power supplies, Cat. No. GEXLPS21, GEXNPS30-120, GEXNPS31-120 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2.The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3.The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40 C. 4. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 5. The drivers are intended for installation inside an electrical enclosure. 6. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. 7. The drivers are suitable for dry location use only except the drivers Models GEXNPS30-120 and GEXLPS21 are suitable for damp location use. LED array drivers, Models GEXLPS21-U, GEPS 12-60U, GE060/MVA/12T12T1-A. 1. These components have been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. The insulation system of the main isolation transformer designated (T2) in these models is a Class 105(A) insulation system. Unless the modules are mounted as specified in condition of acceptability number 7, a temperature test is required when these models installed within an electrical enclosure or raceway. 5. The maximum measured leakage current of a single unit is 0.49 mA. Leakage current measurements shall be performed when multiple LED drivers are used in the final equipment or when the LED driver is used in combination with other equipment in the end-use product.