|
November 14, 2012 SIGN COMPONENTS MANUAL (SAM) 50
<br />Power Grid, PX = Power White XL, PH = Power White HO, XH = Power White XL HO, MM = Mini Max; 'x' denotes design revision
<br />number.
<br />1. These products are only suitable for connection to a Class 2 power source.
<br />2. When units are connected to a Class 2/"LPS" circuit, they are not to draw a total wattage of greater than the secondary or output
<br />rating of the Class 2/"LPS" supply.
<br />3. These products are suitable for use in dry, damp and wet locations.
<br />4. These products described in this section may be cut into segments per manufacture insulation instructions.
<br />5. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions of
<br />Use" as defined in the Sign Components Manual.
<br />6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end
<br />use product.
<br />LED power supplies, Models GECLPS4.
<br />1. LED power supply, Catalog No. GECLPS4 for dry and damp locations.
<br />2. Each power supply output is Class 2.
<br />LED power supplies, Models GECLPS4D.
<br />1. LED power supply, Catalog No. GECLPS4D for dry and damp locations.
<br />2. Each power supply output is Class 2.
<br />LED power supplies, Models GECLPS6 and GECLPSPHA.
<br />1. LED power supply, Catalog No. GECLPS6 for dry and damp locations.
<br />' 2. Each power supply output is Class 2.
<br />LED power supplies, Models GECLPS3.
<br />1. LED power supply, Cat. No. GECLPS3 for dry and damp locations.
<br />2. Each power supply output is Class 2.
<br />LED power supplies, Models GECLPS5, GECLPSPH, GECLPSPW, GECLPSWH.
<br />1. LED power supply, Cat. No. GECLPS5, GECLPSPH, GECLPSPW and GECLPSWH for dry and damp locations.
<br />2. Each power supply output is Class 2.
<br />Power supplies with Class 2 outputs, Models GEPS24-80, GEPS12-60, GEPS24-20.
<br />1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp
<br />locations.
<br />2. These power supplies need to be installed in an enclosure with a means for the connection to conduit.
<br />3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than
<br />13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110°C. Similarly, for Model
<br />GEPS24-20, a temperature test is required when installed in an enclosure smaller than 13.5 by 6 by 4 inches, but the maximum
<br />temperature on the output transformer by thermocouple is 90°C.
<br />4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet locations.
<br />Power supplies with Class 2 outputs, Model GEXNPS30.
<br />1. This component has outputs that qualify as being Class 2.
<br />2. These components are intended for use in dry location only.
<br />3. The transformer employs a Class B (130) Insulation System.
<br />4. These components shall be installed in compliance with the enclosure and mounting requirements of the ultimate application.
<br />5. The maximum room ambient temperature permitted by the manufacture is 50(C.
<br />6. A Temperature Test is required of the power supply installed in an enclosure that measures less than 13.5 by 6 by 4 inches. The
<br />maximum temperature on the output transformer by thermocouple is 110( C.
<br />Power supplies with Class 2 outputs, Models GEPS24-180U, GE180/MVA/24T1-C
<br />1. The maximum measured output voltage, current and power at the output of these models was found in compliance with the
<br />limits for LPS output requirements and additionally evaluated to comply with Class 2 output criteria.
<br />2. The transformer employ Class B insulation system.
<br />3. Power Supply is intended for use in indoor Dry and Damp location only.
<br />4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
<br />and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in
<br />any other direction.
<br />5. Input and Output leads are style 1316, rated 600 V, 105°C, VW-1. Minimum No. 18 AWG. The suitability of input and output
<br />connections shall be determined in each end use application.
<br />6. The power supply was submitted and tested for a maximum manufacturer's recommended Tc point described in the table below.
<br />If adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature test shall be
<br />conducted in the end use product.
<br />Model Input Voltage, HZ Max. Case Temp @ Tc, °C Ambient, °C
<br />GE180/MWV24T1-C, GEPS24-100-277, 60 80 60
<br />180U
<br />LED Light Engine, Cat. Nos. 1110-WH-ZZ-TTK, 1110-RD-ZZ-TTK, catalog numbers where: "ZZ" representing assembly version:
<br />followed by: "TT" - Optional - represents the color temperature of the LEDs in degree "K" Kelvin. Cat. Nos. 1111-XX-ZZ-Y-UK,
<br />catalog numbers may vary per nomendature.: "XX" representing color: RD, RC, YG, GL, SB, BL, WH, YA, WW, GR, PO: "ZZ"
<br />representing assembly version; "Y" representing number of LEDs; followed by: "TT" - Optional - represents the color temperature of
<br />the LEDs in degree "K" Kelvin.
<br />1. These products are only suitable for connection to a Class 2 power source.
<br />2. When units are connected to a Class 2/"LPS" circuit, they are not to draw a total wattage of greater than the secondary or output
<br />rating of the Class 2f'LPS" supply.
<br />3. These products are suitable for use in dry, damp and wet locations.
<br />4. The suitability of the LED Light Engine mounting means shall be determined in the end-use application.
<br />5. The suitability of the LED Light Engine to be used without an additional electrical enclosure shall be determined in the end-use
<br />application.
<br />6. These products described in this section may be cut into segments per manufacture insulation instructions.
<br />7. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions of
<br />Use" as defined in the Sign Components Manual.
|