10179149_419 E. 1ST - Plan - Laserfiche WebLink

Home Browse Search

121 SIGN COMPONENTS MANUAL (SAM)November 14,2012 3. These products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. 4. These products are provided with wire soldered on the printed wiring board for connection. 5. These products are suitable for use in dry, damp and wet locations. Class 2 LEDs, Modules designated, "LED STRIPE2 (Border Light)" and "701956-XXXXXX" series, where XXXXXX may be replaced with alphanumeric characters. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LEDs, "LED STRIPE2 (Border Light)", is rated max. 48 Watts per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dr'y, damp and wet locations. Class 2 LED Module, Cat. No. 701269-=0000000<-MB Series, where x)00000000< may be blank or any alphanumeric characters. 1. These products have been evaluated only for use when connected to the Class 2 output of a Listed or Recognized power source rated 15 V DC or less. 2. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 VDCor less. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in the end product with any available means. 5. These products are rated for a maximum of 7.5 watts or less per module. Class 2 LED Border Light, Class 2 "Border Light", Cat. No. 701189-XXXXXXXXXX series. 1. These products are only suitable for connection to a Class 2 power source, rated 30 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 30 V DC. 3. These products are each rated max. 100 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations when rated maximum 30 VDC. 5. These products are not required to be enclosed or protected from the weather in the end product when rated 30 VDC or less. 6. These products may be secured in place in the end product by any means available. 7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall be considered. LED Strips, Cat. No. 701174, 701181 and 701195 with suffix -R, -Y, -A, -B, -W, or -G followed by -1" through -24" 1. These products are only suitable for connection to a UL Listed or Recognized Class 2,24 volt AC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products may be cut into segments through a black mark provided on the printed wiring board. No other cut across the board is permitted. 4. Cat. No. 701174 is rated for 4.2 watts per foot, Cat. No. 701181 is rated for 9.2 watts per foot and Cat. No. 701195 is rated at 1.5 Watts per foot. The total number of feet of each type and inches for the inch unit are not to produce a total wattage of greater than 60 watts per Class 2 circuit. 5. These products are suitable for use in dry, damp and wet locations. 6. These products are not required to be enclosed or protected from weather. Class 2 LED Module, Cat. No. 701946-XXYUYYYZZZ series, where XX, YYYYYY and ZZZ may be replaced with any alphanumeric characters or blank. 1. These products are suitable for use in dry, damp and wet locations and supplied only with a Class 2 power source rated 24 Volt DC or less. 2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place in the end product by any means available. Class 2 power supply, Model 701285. 1. Power supply is intended to power LEDs in signs. 2. Power supply model is intended for permanent connection only. 3. These units are suitable for use in dry location without a need for an additional endosure and in damp locations when installed inside a sign that complies with the Exclusion of Water Test in UL 48. 4. If the power supply output wiring is extended longer than the 5 foot leads provided, the spliced connections shall be made inside a Listed junction box suitable for the application included with proper grounding. Class 2 power supply, Cat. Nos. 701349, 701351. 1. Power supply models 701349 and 701351 are intended to power LEDs in signs. 2. Power supply model 701349 and 701351 are intended for permanent connection only. 3. These units are suitable for use in dr'y location without a need for an additional enclosure and in damp locations when installed inside a sign that complies with the Exclusion of Water Test in UL 48. 5. These power supplies have two outputs. The Class 2 output circuits are not to be conductively connected to each other in the sign by wiring or other type of component. 6. The maximum rated output power for Model 701349 is 42 watts at each Class 2 output. The maximum rated output power for Model 701351 is 60 watts at each Class 2 output. Class 2 power supplies, Models 701507-MOD, 701507-MOD277 (AD060S277/347-SLN). All may be followed by alphanumeric sumx. 1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on primary circuit.