|
73 SIGN COMPONENTS MANUAL (SAM)June 19, 2013
<br />2. These products are rated per the Table below. When units are connected to a Class 2 circuit, their ratings are to be limited to
<br />draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
<br />IModel Input - Class 2 Output - Class 2
<br />i HM-12RGB5A3-XY Series 12 - 24 Vdc 10-24V 24 W
<br />3. These products are suitable for use in dry, and damp.
<br />4. These products are each rated max. 24 watts. When units are connected to a Class 2 circuit, they are not to draw a total
<br />wattage of greater than the secondary or output rating of the Class 2 supply.
<br />Sign accessories, Class 2 LED power supplies, Model MJ-12100.
<br />1. The output of this component complies with Class 2 requirements in the Standard for Class 2 Power Units, UL 1310.
<br />2. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
<br />min. 2 inches spacing to top of enclosure.
<br />3. These products shall be enclosed in the end product.
<br />4. These power supplies are suitable for use in dry and damp locations.
<br />5. These devices are intended for factory installation only.
<br />6. This Class 2 power supply is not provided with any grounding. The enclosure must be grounded in the end product.
<br />JUSTIN INC E235322
<br />2663 N LEE AVE
<br />SOUTH EL MONTE, CA 91733
<br />Class 2 Power Supply, Model 601-12[)C, 601-12DCR, 101-24DCR, C2240-12DCR, C2240-24DCR, C2240-12, C2240-12-240,
<br />C2240-24, and C2240-24-240.
<br />1. These power supplies have been evaluated for use in LED signs.
<br />2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
<br />3. These units are suitable for *use in dry and damp locations without a need for an additional enclosure.
<br />4. The output of this power source shall not be connected to any other power source or provide power to components connected
<br />to another power source.
<br />5. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at
<br />least 150 mm (6 in) inside.
<br />Class 2 Power Supply, Model 601-12DC-LC, 601-12DCR-LC, 101-24DCR-LC, C2240-12DCR-LC, C2240-24DCR-LC, C2240-12-
<br />LC, C2240-12-240-LC, C2240-24-LC, and C2240-24-240-LC.
<br />1. These power supplies have been evaluated for use in portable LED signs.
<br />2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
<br />3. These units are suitable for use in dry and damp locations without a need for an additional enclosure.
<br />4. The output of this power source shall not be connected to any other power source or provide power to components connected
<br />to another power source.
<br />5. The attachment plug on the end of the power supply cord is not to be removed.
<br />KASON INDUSTRIES INC
<br />57 AMLAJACK BLVD
<br />E363080
<br />NEWNAN, GA 30265
<br />Power supplies with Class 2 output circuits, Model 61815000200.
<br />1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
<br />application.
<br />2. These units are provided with a Class 105(A) insulation system.
<br />3. Input leads are Style 1015, No. 18 AWG, rated VW-1,600 V, 105(C. Output leads are Style 1430, No. 18 AWG, rated VW-1, 300
<br />V, 105°C. The suitability of the input and output connections shall be determined in each end use application.
<br />5. Strain Relief and Impact Tests have not been investigated. The suitability of the enclosure as ultimate enclosure shall be
<br />determined in the end-use application.
<br />6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
<br />unit is V-2 and the necessity of additional fire barriers shall be determined in end product.
<br />7. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
<br />and minimum 2 inches spacing to top of enclosure.
<br />8. The output of the power supply exceeds the Class 2 output limits. This shall be considered in the end product.
<br />5BJ SIGN INC
<br />1800 W ADAMS BLVD
<br />E350092
<br />LOS ANGELES, CA 90018
<br />Class 2 LED Modules, KPL, FPL, KR3.
<br />1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
<br />2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
<br />limited circuit and is rated greater than 12V DC.
<br />3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
<br />rating of the Class 2 supply.
<br />4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
<br />5. These products are not required to be enclosed or protected from the weather in the end product.
<br />6. These products may be secured in place in the end product by any means available.
<br />LED Class 2 Module, KBJ-301, KBJ-303, KBJ-301-S, KBJ-303-S, KBJ-3RGB, KBJ-401, KBJ-403-S, KBJ-4RGB.
<br />1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
<br />2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
<br />rating of the Class 2 supply.
<br />3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
|