|
87 SIGN COMPONENTS MANUAL (SAM)June 19, 2013
<br />SANTA CLARA, CA 95054
<br />Class 2 LED Panel, GLB Series.
<br />1. These products are only suitable for connection to the output of a Class 2 Power Supply rated 24VDC.
<br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
<br />requirements.
<br />3. These products are rated per the Table on Page 2. When units are connected to a Class 2 circuit, their number is to be limited
<br />to draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
<br />4. These products are suitable for use in dry and damp locations without additional enclosures.
<br />LVC CONNECTORS INC
<br />6068 METROPOLITAIN E
<br />E339231
<br />MONTREAL, QC Hl S 1A9 CANADA
<br />PVC Tube, Models LVC-3 and TK-24-XXX.
<br />1. These products are only suitable for protecting listed Class 2 wiring that are supplied by power supplies that are marked as
<br />having a Class 2 output or LPS.
<br />2. For outside wall use only.
<br />3. Not suitable for inside walls.
<br />4. These products may be secured in place in the end product by any means available.
<br />Class 2 Low Voltage Connectors, Model LVC2, LVC4, SNAP-KONEK 111, and STICK-KONEK.
<br />1. These devices are not suitable for interrupting the flow of current by connecting or disconnecting.
<br />2. These products are only suitable for connection to a Class 2 power source, Class 2 supply rated max. 15 Volts AC or max. 30
<br />Volts DC or less.
<br />3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
<br />and energy limits.
<br />4. These products are suitable for use in dry, damp and wet locations.
<br />5. These products are not required to be enclosed or protected from the weather in the end product.
<br />6. Modules can be installed to interconnect leads in the field or pre-installed.
<br />7. These products may be secured in place in the end product by mechanical securement or double sided adhesive tape.
<br />8. For Model LVC2 and LVC4, suitable for connecting stranded wires which are 18, 20 or 22 AWG with compatible wire guide
<br />inserts.
<br />9. For Model SNAP-KONEK Ill, suitable for connecting single conductor per channel either AWM wires 18-24 AWG, or Power-
<br />Limited Circuit Cables type CL3P, CL3R, CL3, CL3X, CL2P, CL-2R, CL2, CL2X and PLTC.
<br />10. The Model STICK-KONEK base and button are used to join LED strips, LED bars, or LED leads wires.
<br />AGTECH INDUSTRIES CORP E314969
<br />5625-A S ARVILLE ST
<br />LAS VEGAS, NV 89118
<br />Class 2 LED M od u l e, C a t. N o. L P 1 2 0 6 0 P- 08, L P 1 2 0 60 P-09, L P 1 2 060 P- 1 0, L P 1 20 60 P - 1 1, LP 1 2 0 6 0 P - 1 2, L P 2 4060 P- 22,
<br />LP24060P-23,LP24060P-24.
<br />1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
<br />Class 2 output requirements for dc circuits.
<br />2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
<br />3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
<br />and minimum 2 inches spacing to top of enclosure.
<br />4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on both
<br />primary and secondary circuits.
<br />MATRIX FRAME
<br />FLEVOWEG 27
<br />E351057
<br />2318 BZ LEIDEN, THE NETHERLANDS
<br />Class 2 LED Module, "Lightbox CREE XP LEDstrip".
<br />1. These products are suitable for use in Dry and Damp Locations Only and may only be supplied with a Class 2 power source with
<br />Current limit rated max. 2.5 Amps or less.
<br />2. These products are only suitable for connection to a Class 2 or LPS power source, rated 24 Volt DC or less.
<br />3. These products shall be mounted in equipment, which provide a suitable overall enclosure.
<br />4. A maximum of 4 Led strips are allowed to be mounted in a row, as detailed in the mounting instructions.
<br />5. These products may only be installed in a metal based enclosure (frame) that is able to transfer the heat that comes from the
<br />LEDs over the metal-core Printing Wiring Board into the ambient.
<br />MATRIX FRAME
<br />FLEVOWEG 27
<br />E358648
<br />2318 BZ LEIDEN, THE NETHERLANDS
<br />Class 2 LED driver box, Model A120606.
<br />1. The power supply has been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
<br />2. The Class 2 output of the power supply is suitable for use in dry and damp locations only.
<br />3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
<br />and minimum 2 inches spacing to top of enclosure.
<br />4. These products shall be enclosed in the end product.
<br />5. These products are suitable for factory wiring only.
|